Search Documents

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [ ] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m%-sec instead of meters. Adding the gravitational constant corrects this: [ ] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per sec). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [ ] References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters' Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 3, 1985

By J. R. Sturgul

A dynamic input-output model for a coal power enterprise that now includes four underground coal mines, three coal washing plants, a power plant and a railway transportation system was developed. The model is applied to analyze investment alternatives for long-term development, including the expansion of existing mines, the opening of new mines, the construction of new coal washing and power plants and the upgrading of the railway system. As a result, the optimal investment strategy with capital schedules and projected sector outputs is obtained. Also, the importance of the new power plant to the strategic development of the company is demonstrated. It is concluded that, without applying a dynamic input-output model, it would be much more difficult or impossible to conduct such a systematic and compete analysis.

Jan 1, 1999

By E. S. Erickson, R. L. Stone

Introduction Evidence from blast furnace operations has indicated that using pellets with a higher ISO low temperature reducibility, a lower SiO2 content, and better resistance to low temperature degradation results in considerable coke savings and improved furnace operation. Although these benefits could not be directly related to reducibility differences alone, we believed there was sufficient evidence of the advantages in improved pellet reducibility to warrant laboratory investigation of ways and means to effect such improvements. It is well known that pellet reducibility can be significantly altered by changes in the basicity and the amount of non-iron oxide constituents. Past work (Friel and Erickson, 1980, 1982; Saeki et al., 1977; Thanning, 1974) has shown that with increased MgO contents, and at optimum CaO/S1O2 ratios, significant improvement in low temperature reducibility can be attained. The improved properties of such fluxed pellets have reportedly led to increased blast furnace efficiency and productivity (Saeki et al., 1977; Ilmoni, 1975). Less well known, however, is exactly what factors control reducibility in acid pellets. Because of this gap in knowledge, studies were undertaken of the factors affecting reducibility in acid pellets and to estimate their relative significances in modifying reduction behavior. This paper describes that part of our work done to determine the effect of bentonite on reduction behavior. Our approach was to first examine the effect of bentonite's presence on as pure an iron oxide as possible (i.e., a magnetite "superconcentrate" containing about 0.2% SiO2) so as to eliminate any gangue-binder interaction. The next step was to look at bentonite effects on concentrates with only limited amounts of gangue (containing about 1% SiO2), but of two different types, simple and complex silicates. Last, we

Jan 1, 1988

By V. B. Menon, L. D. Michaels, M. E. Mullins

Introduction The cleaning of coal to remove sulfur and inorganic impurities has, in recent years, become an essential operation in any coal utilization process. US coals, on average, contain about 3% total sulfur, of which more than 60% is generally inorganic or pyritic sulfur. Existing technologies such as heavy media cycloning, selective agglomeration, and electrostatic separation have the potential for removing about 80% of the pyrite from coal (Khoury, 1981). In view of the large volumes of coal being used today, there exists a need for the development of new processes to further improve the separation of pyrite from coal. Colloidal particles in suspension possess surface charges that are related to the chemical composition of the particles. In aqueous suspensions, the surface charge is a function of pH. For coal-pyrite mixtures, it is possible, by an adjustment of the pH (also a function of polar molecules), to reach a state where the charge on coal is very close to zero, but the charge on pyrite is still substantial. The introduction of collector particles with a charge opposite that of the pyrite should then result in the selective flocculation of pyrite and collec¬tor. These flocculates should settle out much faster than coal and could be removed from the bottom of the settling column. This note discusses our preliminary observations of the effect of clay-based collector particles, especially bentonite, on the settling behavior of coal and pyrite. These experiments were conducted with a view to developing a new electrokinetic flocculation process for separation of coal-pyrite mixtures. Experimental The objective of the experiments was to determine the effects of clay-based additives on the settling rates of clean coal, pyrite, and coal-pyrite mixtures. Illinois Colchester (No. 2) coal was obtained after processing in an existing coal cleaning facility. This coal was reported to contain less than 0.3% pyritic sulfur, which was in the form of a fine powder with an average particle size of 5µm. Pyrite (of average particle size 5 µm) was also obtained from the same facility and reportedly contained less than 0.1% coal. The zeta potentials of coal and pyrite in water were measured as a function of pH using a zetameter. The pH was adjusted by adding sodium hydroxide or hydrochloric acid to the suspensions. Sedimentation experiments were conducted in 50-mL glass cylinders, and settling rates were measured by noting the height of clear liquid above the settling front as a function of time. Settling behavior was also charted by periodically taking photographs of the system. The following systems were investigated: •a slurry consisting of 2.5 g of clean Illinois Colchester coal in 50 mL of water of pH 6.0, with and without the addition of 0.5 g of bentonite (Fisher, purified grade) ; • a slurry consisting of 2.5 g of pyrite in 50 mL water of pH 6.0, with and without the addition of 0.5 g of bentonite ; and • a slurry consisting of a mixture of 1.25 g clean coal and 1.25 g pyrite in 50 mL water of pH 6.0, with and without the addition of 0.5 g of bentonite. In addition, experiments were conducted with kaolinite (Bath, South Carolina) and alumina (Fisher, purified grade) as collector materials to verify the observed effects. Results and discussion Figure 1 shows the zeta potential values for the Illinois coal and pyrite as a function of pH. The zeta potentials of coal and pyrite decrease with increasing pH, changing from an initially positive value at low pH to a negative value at high pH. The point of zero charge (PZC) for the coal is at a pH of 6.2, while the PZC for pyrite occurs at a pH of 10.3.

Jan 1, 1988

By R. W. Smith, Z. Sadowski

INTRODUCTION Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of contaminant metal ions and other chemicals on the flotation. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances, cations such as Ca2+, Mg2+, Fe2+, and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions. Some adsorption (abstraction) experiments were also performed. Experimental materials and methods The barite used was a high-purity, naturally occur¬ring mineral sample (Kings Creek, SC). The material was ground in a porcelain mill and a fine fraction (mean particle size 11.49 µm) separated out by air elutriation. The mean size was determined by an aqueous sedimentation method using a CAHN electro-balance. In the method, an 0.6-g sample of the barite was dispersed in 450 cm3 of pH 7 water containing 0.01 g of sodium tripolyphosphate. The mean particle size was denoted X0. The stability of the barite suspensions was determined by a comparison of the mean size of the investigated barite suspension aggregations with the mean size of barite powder determined in the presence of sodium tripolyphosphate. The mean sizes (X) of the barite aggregations were determined using the same amount of water and barite sample as in the measurements of dispersed barite particle size but without the presence of polyphosphate. The ratio X/Xo is thus a measure of the stability of a suspension (the greater the ratio, the less stable the suspension). The adsorption (abstraction) experiments were carried out in polyethylene bottles containing 1 g of barite powder in 200 mL of solution. The solids were added to a solution containing a known concentration of metal chloride salts (AlCl3, FeCl2, MgCl2, and CaCl2) . The pH was controlled by both HCl and NaOH addition. The suspensions were agitated in a shaker for three hours. The final ion concentrations in solution were determined by atomic absorption analysis. The electrokinetic measurements were made using a Komline-Sanderson Zeta Reader in a conventional manner. All experiments were carried out in the presence of 1.0x10-3 k.mol/m3 NaClO4. Experimental results Figure 1 shows the zeta potential of barite particles as a function of pH in the presence of iron(II). The

Jan 1, 1988

By M. Khandrika, B. K. Parekh

Column flotation has proven to be the most effective technique for the flotation and recovery of ultrafine coal. The commercial application of columns in the coal industry is steadily increasing (Parekh et al., 1990; Yoon et al., 1992). For the flotation of coal or mineral air is used for generating bubbles. Using a conventional flotation cell, Miller and Mishra (1985) compared froth flotation behavior of fine coal using air, nitrogen and carbon dioxide gas. They concluded that carbon dioxide gas provided a higher rate of recovery and a lower ash content. The objective of the present study was to investigate the effect of various gases such as compressed air, nitrogen, argon, and carbon dioxide on the column flotation of fine coal.

Jan 1, 1999

By R. Poulin, R. Pakalnis, D. Peterson

Introduction A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water: cement ratio between 0.35:1 to 0.4:1. The prototype, developed from Phase I, was technically comparable to that of conventional steel cable bolts. However, high cost and limited accessibility hindered its commercial acceptance. The second phase of the project was sponsored by the British Columbia Science Council and Pacific Pultrusions Ltd. of British Columbia to locally develop a glass fiber cable bolt. This phase of the project has resulted in the DAPPAM cable bolt (Pakalnis et al., 1994). DAPPAM Cable bolts are the second most used support method in Canadian underground mines after mechanical rock bolts. It is projected that 870,000 m (2.9 million ft) of cable bolts are installed annually in Canada (Poulin et al, 1994). The objective of the research program was to develop a glass fiber cable bolt with similar pullout strengths to the conventional steel cable bolts (267 kN - 60,000 lbf). More than 200 laboratory pull tests were conducted employing standard cable bolt test procedures, as outlined by the US Bureau of Mines (Goris, 1994), to assess optimum rod and surface composition, geometry, number required, pullout and shear characteristics, among others. This resulted in the DAPPAM cable bolt (Fig. 1). It consists of 10 individual 0.6cm-diam (0.25-in.-diam) rods enveloping a 2.2-cm (0.8-in.) outside diameter, high-density polyvinyl grout tube. The composite used in the construction of the rods is comprised of about 65% glass fiber within a 35% polyester resin matrix (by volume). Through pultrusion (a continuous fabrication technique), the fibers and resin are combined into a composite material. The strength of the overall composite is largely governed by the material properties, the alignment [ ] of the fibers relative to the applied load and the density and interaction of the overall components within the composite. A further modification to the composite was the addition of a sand grit to the surface of the individual rod. This increased the overall bond strength between the rod and the cement-based grout, used to solidify the cable bolt to the rock mass. The grout tube has an inside diameter of 1.9 cm (0.75 in.) and is rated at a pressure of 1.72 MPa (250 psi). During installation, the grout is pumped through the annulus of the grout tube thereby filling the hole from toe to collar. Laboratory and field trials concluded that a minimum drill hole diameter of 4.8 cm (1.08 in.) be used to ensure optimum grout coverage. Table 1 compares the design strengths (as tested) for DAPPAM vs. the ultimate strengths for a conventional 1.6cm (0.6-in.) steel cable bolt. The characteristics for the steel cable have been derived directly or indirectly by Goris et al. (1994). A design tensile strength of 289 kN (65,000 lbf) was proposed for the composite developed. However, recent tests have indicated maximum breaking strengths of more than 400 kN (90,000 lbf) (Fig. 2). Figure 2 shows the load vs. displacement pull out curves for steel and DAPPAM cable bolts. The methods of testing were standardized so as to be able to compare the results directly. The shear strength of the fiberglass cable is largely a function of the surface area sheared. Shear strengths of 89 kN (20,045 lbf) were obtained for the configuration shown in Fig. 1 when sheared normal to the axis of the cable. The testing procedure was similar to the shear tests performed on steel by Goris (1993). It is important to reinforce the implication that critical bond strength has on the success of an overall support system.

Jan 1, 1995

By G. G. O. O. Uwadiale, M. A. U. Nwoke

The flotation of Azara barite tailings was investigated using crude rubber nut oil (RNOc), refined rubber nut oil (RNOR) and oleic acid as fatty acid collectors. Chemical characterization of the rubber nut oils indicated high acidity, high saponification values and high iodine indexes, which are indicative of a high fatty acid compositions. The Azara barite tailings analyzed 64.6% BaSO4 by atomic absorption spectrophotometry. Gravity and magnetic separation techniques yielded a BaSO4 concentrate with a grade of 74.8% and a recovery of 92.5%. Barium sulfate grades of 90.0%, 92.8% and 94.8% with recoveries of 80.3%, 85.4% and 86.7% were achieved with collector dosages of 750g/t crude rubber nut oils, refined rubber nut oils and oleic acid, respectively. Hence, rubber nut oils are effective fatty acid collectors for the flotation of barite tailings.

Jan 1, 1998

By G. G. O. O. Uwadiale, M. A. Kollere, M. A. U. Nwoke

Birnin Gwari and Alawa graphite deposits were upgraded by flotation. Using 0.5 kg/t kerosene and 0.25 kg/t sodium silicate, flotation concentrates grading 90.7% and 88% Cg with recoveries of 86.2% and 84% were produced from Birnin Gwari and Alawa graphite samples, respectively. The combination of 0.5 kg/t kerosene, 0.2 kg/t pine oil and 0.25 kg/t sodium silicate yielded high-grade graphite (92.3% Cg) with a recovery of 83.9%. Flotation with refined rubber nut oil and kerosene, at a 1:1 ratio, produced a concentrate grade of 86.3% Cg with a recovery of 90.4%. With acid leaching of the flotation concentrate, a high-grade graphite concentrate containing 98% Cg was produced.

Jan 1, 1998

By R. D. Schmidt, S. E. Follin

Introduction Mineral recovery from an in situ leaching operation is determined by the often complex interaction of hydrology, mass transport, and chemical kinetics. The operating conditions of many pilot and production scale uranium leaching operations involve heterogeneities in aquifer permeability. Differences in permeability may be naturally occurring, the result of differences in main size or cementation, or they may be induced by leaching activity. Variations in permeability directly affect the fluid flow streamline pattern, fluid flux, and so also leaching geochemistry and uranium recovery. An in situ leaching hydrology model (ISL) and a mass transport-oxidation rate model (ISLGC) have been developed for use in making site specific predictions of the leachability and productive potential of heterogeneous ore deposits, and for the optimal design of leachant injection and recovery operations. The two models are linked by output and input requirements. The ISL hydrology model generates a leachant flow streamline pattern between injection and recovery points in a flow domain incorporating regions of arbitrary permeability. The ISLGC transport model describes the changing solution concentrations of uranium and oxygen and the changing mineral concentrations of uranium and pyrite resulting from convection, longitudinal dispersion, and oxidation reactions. ISL hydrology model Basic equations The differential equation for steady-state two- dimensional flow in an isotropic porous medium is

Jan 1, 1988

By L. W. Saperstein, M. C. Radomsky, D. L. Passmore, J. D. Bennett

About 60 small surface coal mines in Pennsylvania participated in a program designed to improve safety performance in the workplace. The method involved the use of safety sampling and observation to assess the degree of safety exhibited by workplace behavior and conditions. Data were collected through the use of on-site safety instruments covering seven major occupational positions typical of small surface mines. Workplace events observed (acts and conditions) were assigned a hazard classification. Feedback was initiated to improve safety performance in areas failing to conform to appropriate safety standards. Results suggest that the variety of unsafe acts and conditions associated with the companies observed are extensive. Further, the experiences drawn from this pilot project have proven the need to pursue this behavioral approach. Future research should concentrate on subjecting the present approach to a strict experimental design involving randomly selected “poor risk” mines.

Jan 1, 1987

By J. J. Snodgrass

Faults, sandstone channels, and abandoned mine workings present severe safety hazards, disrupt mining, and necessitate costly precautions or discontinuance of operations. In addition to fault detection, mining companies have a need to map discontinuities such as seam thinning and previously mined areas in both longwall and room-and-pillar operations. Initial field tests demonstrated successful generation and propagation of higher order guided wave modes. Theoretical studies indicate potential for improved resolution by sensing small details in the coal seam and roof structure. Controlled-waveform source transducers and specialized detectors are particularly useful to preferentially excite and detect the Love (SH) and Rayleigh-type (P-SV) waves, including the higher frequency modes. The distinct observation of reflections using the transducers in the shear wave mode makes feasible the detection of the water-filled voids.

Jan 4, 1985

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations reluted to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 3’% to 1% S and greater than $28.65/t ($26 per st) for removal below 1% sulfur.

Jan 8, 1987

By S. G. Malghan, J. P. Van Dillen

Introduction Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined. HGMS of Uranium Ores The mechanism by which uranium minerals are attracted to a magnetic field is either due to its magnetic susceptibility or its association with other minerals that are magnetic. Data on magnetic susceptibility of uranium minerals are scarce. The only reported data are for uraninite at 2360 X 10-6 cm3/mole. Povarennykh (Andres, 1976) concluded that the magnetic properties of minerals depend on: • Structure of the outer electron shell in a mineral with electropositive atoms; • Valence of the atoms; • State of the chemical bonds; • Type of coordination; and • Proportion of magnetic atoms (Fe, Mn, Cr, and Ni) in the composition of the mineral. However, information on the magnetic susceptibilities of the constituent atoms of a mineral alone does not suffice for evaluating the mineral compound as a whole. Most often, uranium minerals can be beneficiated by HGMS if they are associated with other minerals that are magnetic. This appears to be a more predominant mechanism by which the uranium minerals are beneficiated. Experimental A Sala-HGMS (Malghan and Subramanian, 1981), model 10-15-20, separator was used in the experiments. The matrix material-ferromagnetic stainless steel in the form of expanded metal or steel wool-was packed into a 38-mm (1.5-in.) diameter by 360-mm (14-in.) long canister. The matrix material occupied only a 150-mm (6-in.) length. The experimental set-up and slurry flow direction are described elsewhere (lannicelli, 1976). The response of uranium ores in the HGMS was studied by feeding well-dispersed slurry at 10% solids and examining the influence of process variables on selectivity and overall uranium recovery. The chemical and mineralogical characteristics of the ores under study are presented in Table 1.

Jan 12, 1983

By Wu Xueling

9K medium was used to isolate iron-oxidizing bacteria from 27 sump water samples collected from Dexing Cop-per Mine, Chengmen Mountain Mine and Yin Mountain Mine, Jiangxi Province, China. Lead acetate and silver nitrate were used to enrich metal-resistant iron-oxidizing bacteria from the above water samples. Isolate 16 was isolated from the sample taken at Dexing Copper Mine. Growth experiments indicated that when incubated under lead acetate (3,500 mg/L), isolate 16 still carried out ferrous ion oxidation, while isolate H1, a less resistant strain taken at Yin Mountain Mine, had a tolerance level of only 400 mg/L. When assayed with other metals, i.e., Ag+ (240 mg/L), Hg2+ (0.9 mg/L), Cu2+ (32,000 mg/L) and Mg2+ (22,500 mg/L), isolate 16 still carried out ferrous ion oxidation while, on the other hand, isolate H1 exhibited much lower tolerance levels, i.e., Ag+ (60 mg/L), Hg2+ (0.1 mg/L), Cu2+ (19,000 mg/L) and Mg2+ (13,500 mg/L). Based on 16S rDNA sequence data, isolate 16 and H1 were both identified as Acidithiobacillus ferrooxidans.

Jan 1, 2007

By J. R. Frederick

Introduction In response to industry needs and requests, Joy Mining Machinery is aggressively evolving a "game changing" system of underground development mining machinery. This entry-development system (EDS) project is concentrated on providing clean, protected and ergonomic operator areas and a quantum leap in productivity. To meet these goals, a virtually continuous and automated mining system is needed. Operators must be able to efficiently and ergonomically perform required functions from a protected environment. Health-related issues, such as respirable dust and noise, must also be addressed. A new concept system of integrated face equipment, from the continuous miner to and including advancing the section belt and services, is needed. Phase I of the project was aimed at developing the bolting technology required. Through acquisition of Cram Australia and joint development efforts with Canyon Fuel Co., Joy now has this capability. The test platform, known as the Joy Multibolter, has successfully completed its trials at Canyon Fuel's SUFCo Mine (Fig. 1). These tests validated the bolting technology and operator protection and ergonomic issues. Phase II includes the development and testing of an integrated mining machine (IMM) capable of advancing a heading 1.5 m (5 ft) while simultaneously cutting a fullface width (single pass) and installing a complete bolt pattern. The IMM, unveiled at MINExpo 2000, incorporates the bolting technology of the Multibolter with automated full-face cutting. This machine was designed to meet Joy's stringent health, operator protection and 300m/d (1,000-ft/d) productivity goals. Phases III through V will include development of processes and integrated haulage, ventilation, power, material handling and section services advancing equipment. Processes and equipment developed will be designed for seamless integration into a complete entry development system. The focus of this paper is the new continuous miner (IMM) development, proposed testing and expectations for the EDS. The IMM is scheduled for commissioning and trials beginning in April 2001 at the SUFCo Mine. SUFCo Mine Canyon Fuel Co. is jointly owned by Arch Western Resources and the Itochu Corp. of Japan. It owns and operates three coal mines in Utah: the SUFCo Mine in Sevier County, the Skyline Mine in Carbon and Emery Counties and the Dougout Canyon Mine in Carbon County. Incorporating state-of-the-art-mining technology and advanced mine management practices, the SUFCo Mine is one of the most efficient underground coal mines in the world. The SUFCo Mine is located approximately 50-km (30 miles) northeast of Salina, UT, in the Wasatch Plateau portion of the Uinta coal basin. The mine property consists of 9,900 hm2 (24,470 acres) with approximately 118 Mt (130 million st) of recoverable reserves. Public utilities and industrial concerns purchase approximately 95% of the coal mined at SUFCo through short- or long-term contracts. Coal reserves are extracted by longwall mining, and the panels are developed using continuous miners. The longwall face at SUFCo Mine is 283-m (930-ft) wide, and the seam height ranges from 2.4 to 4 m (8 to 13 ft). The two development sections are in full operation using Joy 12CM12 continuous miners. Two super longwall panels, under development in the northeast portion of the lease block, are 4,270-m (14,000-ft) long with a 283-m (930-ft) wide longwall face. Each panel contains approximately 5.4 Mt (6 million st) of recoverable coal. SUFCo has been a world leader in productivity for a

Jan 1, 2003

By P. Venkatasubramanian

The selection of a mining method for a mineral deposit is a complex decision problem. Human judgment, based on experience with mineral deposits and geologic conditions, remains the single most important input of the decision-making technique. If the use of artificial intelligence, in particular the developments in expert systems, is taken to its logical conclusion, the experience of the domain experts could be incorporated into a decision-support expert system. A knowledge-based decision support system for mining method selection for ore deposits has been designed whereby the domain knowledge is represented as production rules and organized in a semantic tree representation. This model is written in the PROLOG language. While the verification difficulties of expert systems models are recognized, an example of the model's decision on the mining method for a given ore body is presented and shown to be consistent with the decision made by human experts. In addition, plans, for further verification of the model are delineated.

Jan 1, 1992

By L. G. Austin

The data of Dunn and Martin (1978) is reanalyzed using a rigorous application of Hertzian theory to the impact process. The Young's modulus of steel required to fit their data to the theory is a factor of about 10 3, too low compared to the values quoted for steels. Thus, doubt is thrown on the validity of their experimental technique, and it is possible that their values for maximum impact force and stress are far too low.

Jan 1, 2002

By A. A. Odunaike, E. G. Okafor, M. H. Mokwe

Microscopic Studies were performed on ore samples from the Muro banded iron ore deposit in Nigeria and the Marampa iron ore deposit in Sierra Leone. Ore characteristics that affect processing of both ores were compared with a view toward assisting mineral processing engineers in choosing the most suitable methods for upgrading the ore. The Nigerian ore contains 30% to 37% (by weight) Fe and the Sierra Leonean ore contains 34% to 51% (by weight) Fe. Hematite is the main iron mineral in both ores. The Sierra Leonean ore is relatively coarse grained (typically around 250 µm) and can be upgraded by conventional gravitational methods. In contrast, the Nigerian iron ore is fine grained and must be ground to -74 µm to liberate the hematite for recovery by flotation. Both ores contain high percentages of phosphorus and sulfur, which are above the required specifications for direct reduction and blast-furnace practice. These deleterious elements can be rejected by grinding and flotation.

Jan 1, 1999

By R. L. Grayson, G. Mishra

Introduction Many old underground mines have been developed extensively into reserves requiring large numbers of workers to maintain and rehabilitate lengthy track haulages and/or belt conveyor systems. Often, large numbers of fans are required to maintain minimal airflows in areas where poor conditions and huge leakages prevail. Problems that beset one such coal mine and projects undertaken to restore it to potential profitability are presented. Brief history The Vesta No. 5 mine was opened in 1908. Drift development began near the Monongahela River, which was the primary avenue for shipping metallurgical coal to coke ovens in Pittsburgh. Over the ensuing 75 years, the main haulage entries were developed a distance of 16.1 km (10 miles) to the present mining area. Track haulage was used to transport coal from working sections to the river loading facility. As haulage distance and areas of high water influx increased, management decided, in 1973, to construct an underground conveyor belt system. The project spanned 36 months and culminated in a system of 22 flights, ranging from 205.7 to 1767.8 m (675 to 5800 ft) long. Six intake and eight return entries were developed as the mains were advanced. These entries provided adequate ventilating capacity over the years, but as extensive gob areas progressed and roof conditions deteriorated, the entries became inaccessible and more resistant to airflow. By 1981, five fans were being used to circulate 943.9 m3/s (555.5 cfm) of air through the mine. An average of 6440 t (7100 st) were produced from 20.8 continuous miner unit shifts and 2.7 longwall unit shifts each day in 1981. The ratio of support to production personnel was 1.94. To maintain the outby 16.1 km (10 miles) of haulage, 110 personnel were used. The average cost per ton was $43.54 ($39.58 per st), resulting in excessive bottom-line losses. The mine possessed a rather promising reserve, mostly in lease, of good quality, medium-sulfur metallurgical coal, but it also had a number of formidable operating problems. Operating problems Contributing factors toward relatively low productivity and high costs were the conditions of the track haulage, conveyor, and ventilation systems. Productivity was affected greatly by downtime associated with the conveyor system, which lacked adequate access for making splices or other repairs. Many areas within the conveyor belt entry itself required more

Jan 3, 1987