Search Documents

By J. J. Kellar

Researchers have long speculated regarding the adsorption state of collectors on mineral surfaces. Only recently have analytical techniques become available which allow direct in-situ analysis of adsorbed layers. Fourier transform infrared spectroscopy coupled with internal reflection spectroscopy (FT-IRJIRS) with reactive internal reflection elements allows for unobtrusive investigation of the adsorbed layer (Harrick, 1979). This technique has been used both for the in-situ identification of adsorbed species and for the direct calculation of collector adsorption density in real time from infrared spectral data (Miller and Kellar, 1988). The reactive mineral IRE serves both to internally reflect the infrared light and to act as a substrate at which collector adsorption can be monitored. Shown in Figure 1 is a schematic of light being internally reflected in an IRE. As the light is totally reflected at the interface, an evanescent wave propagates a short distance (typically a few microns) away from the IRE, and sampling of the interfacial region occurs. Because of multiple internal reflections, great sensitivity can be obtained. Flotation systems for which this method has been demonstrated include CaF2/oleate, Al2O3/ dodecyl sulfate, CaCO3/oleate, ZnS/xanthate, and KCl/octylamine (Miller and Kellar, 1988; Kellar et al., 1989, 1990; Miller et al., 1990).

Jan 1, 1992

By M. Alnot, J. A. Mielczarski, J. J. Ehrhardt, J. M. Cases

The flotation behavior of minerals depends on the balance between hydrophobic and hydrophilic species present at the surface of the minerals. The direct characterization of the interfacial products formed by the interaction of water and an aqueous solution of amyl xanthate with chalcopyrite, tetrahedrite and tennantite (the two former contain antimony and arsenic) were carried out by X-ray Photoelectron Spectroscopy (XPS) and infrared (IR) reflection spectroscopy. The experimental data collected from in-situ (IR ATR) and ex-situ (XPS, IR External Reflection) measurements have let us determine the types of the adsorption products and to propose mechanisms of interaction between the aqueous solution of surfactant and surface of the investigated minerals. It is shown that two major processes take place at the mineral interfaces: (i) the interaction with water and oxygen resulting in the formation of the oxidation products which are mainly hydrophilic (but also a hydrophobic product was found), and (ii) the adsorption of xanthate producing different types of hydrophobic surface products. The results obtained show differences in the composition of the outermost atomic layers of the investigated minerals which obviously will produce differences in the flotation behavior of these minerals. This work forms a good fundamental basis for a better separation between copper minerals containing arsenic and antimony, and chalcopyrite.

Jan 1, 1995

By Frank W. Bowdish

Studies of sulfidization and flotation of chrysocolla involving the use of pH and sulfide ion instruments, a Zeta meter, microflotation techniques, and sensitive determinations of adsorbed sulfur have given new insight into the mechanism of the process. Factors that affect the recovery of sulfidized chrysocolla by flotation appear to be the pH at which it is sulfidized, and certain alterations of the surface that occur during aging after sulfidization. Such aging results in increased recoveries. The surface charge, as measured by electrophoretic mobility, of chrysocolla shows an unexpected negative increase as pH values are changed from 6.0 to about 4.5, and this appears to be correlated with increasing sulfur adsorption and flotation recovery over the same or even wider pH ranges.

Jan 1, 1970

By K. Darcovich

The wettabilities of agglomerates made from coals of several different ranks were measured by the adhesion technique. Oil levels from 0 to 10% by weight were used. As was expected, it was found that higher-rank coals are more easily oil-wetted and that the surface properties of the agglomerates correlate with agglomeration recovery and ash removal data.

Jan 1, 1992

By N. Arbiter

If two fluid phases are brought into contact with a solid, one fluid may completely wet the surface to the exclusion of the other, or both may wet it, forming a three-phase line of contact. These relative wetting tendencies are quantified by the contact angle 0 which is related by Young's equation (1,2) [12 cos? = 13 ? 23] [to the three interfacial tensions (3). No contact angle for the first fluid, indicating that it does not wet the solid in the presence of the second, means that the difference between the two solid-fluid fluid surface tensions, - 8 is greater than (or just 13 -23 equal to) the fluid-fluid tension 12; a finite angle indicates that the difference is less.*]

Jan 1, 1964

By C. E. Zebula, F. F. Aplan, R. S. Datta

The hydrophobicity of oil shale was found to follow the sequence R-5 > Mahogany >> Eastern. Further, hydrophobicity was found to correlate with the total organic carbon (TOG) content, decreasing with increasing specific gravity of raw oil shale pieces. Differences in hydrophobicity from piece to piece indicate that gravity preconcentration would be much more effective for Western than for Eastern oil shales. Purified kerogen concentrates and low specific gravity fractions (<2.0) of raw Western oil shale samples show critical surface tension of wetting values of [y]c = ~35 mNm -1, and for a kerogen concentrate from an Eastern oil shale [y]c = ~46 mNm-l. This infers that dust from oil shale mining operations can be suppressed by surfactant solutions similar to those used to suppress coal dust.

Jan 1, 1988

By A. Marabini, G. Belardi, N. Sheau, F. Veglio

The present paper deals with the modelling of a Multi-gravity separator in the treatment of chromite fines. A first screening study was carried out by 2" full-factorial experiments in order to check the main effects and interactions among the investigated factors: shake frequency, shake amplitude, tilt angle and washwater flowrate were taken in consideration in the study. Two size fractions were employed in the experimental tests. Successively, considering the factor with larger influence on the Cr203 and SiO2 grade and Cr203 recovery in the concentrate, a further improvement of the experimental design was performed to determine empirical models to describe the behaviour of the MGS in the mineral treatment. The results show how intrinsic interaction among the factors take place, highlighting that an optimization study must be carried out considering all the MGS setting parameters.

Jan 1, 1995

By M. J. McPherson, P. Mousset-Jones, G. Danko, I. M. Konduri, F. Calizaya

The flow of air through a bare rock, underground airway is affected by the size and frequency of the micro- and macro-asperities of the rough surface. The focus of this study is to characterize this roughness using the coefficient of friction, the friction factor and the fractal dimension. The rough surfaces were identified by two sets of 177 and 78 transverse profiles measured by a laser profiler along the length of an underground airway at the Sunshine Mine, Idaho. Based on the measurements, the friction factor was estimated from Atkinson&apos;s equation and the coefficient of friction from the Moody diagram, and power series and variography were used for computing a fractal dimension for the airway surface. Significant conclusions are reached relating the effect of error in the measurement of cross-sectional and rubbing surface areas of a drift, on the estimated friction factor for the airway. The potential role of the fractal dimension as an alternative to the friction factor for characterizing the roughness of a mine airway is discussed.

Jan 1, 1993

By Penglu Gan, Jinjie Zou, Chenglang Pan, Xiaowu Tang, Yu Zhao

"The north segment of the Zizhi Tunnel that consists of twin tunnels was excavated at a shallow depth in soft ground using the Shallow Tunneling Method. Based on continuous field measurements, the development histories of surface settlement were analyzed first. The observed development process could be roughly divided into three stages and the influence of river was evidenced. Transverse and longitudinal surface settlements above the twin tunnels were then fitted with empirical models. The obtained trough width parameters in transverse and longitudinal direction (it and il) and the volume loss (VLs) were presented and discussed. Additionally, surface settlement was compared with the crown settlement. The relationship between surface and crown settlement behaved in two different ways inside and outside the river-affected region. The findings in this project give references for predicting surface settlements in similar tunneling condition. INTRODUCTION Nowadays tunnel construction has become a major way of utilizing underground space in many large cities. The ground deformation will be inevitably induced in the tunneling process. Engineers should always be careful about excessive deformation that may damage adjacent structures. For shallow tunnels, controlling ground deformation turns to be more risky. Since soil arching is not completely formed in the shallow tunneling, settlements can easily develop from tunnel crown to ground surface.A conventional tunneling method named Shallow Tunneling Method (STM) has been developed and widely applied to constructed shallow tunnels in China. The major difference between this method and the New Austrian Tunneling Method (NATM) is whether considering self-supporting capacity of surrounding ground or not. In order to reduce the disturbance of surrounding soils, several guidelines are highlighted in this method, including advanced pipe forepoles, strict grouting, short excavation length, strong support, quick closure and frequent measurements (Fang 2012). Nevertheless, the ground deformation is still hard to control and becomes a concerned problem, mainly because ground settlement has some regional features and largely depends on the detailed excavation methods (bench cut method, multiple heading method, etc.) and ground condition (sand, clay, decomposed rock, etc.)."

Jan 1, 2016

By Paul E. Richardson, Edwin E. Maust

Cyclic voltammetry and surface potential (photovoltage) measurements have been carried out on galena electrodes in sodium tetraborate solutions with added HC1 and NaOH to adjust the pH over the range 2 to 13. The first technique shows that the surface species formed on moderate anodic polarization and reduced on subsequent cathodic polarization are the same over the entire pH range. At anodic potentials, a soluble metal species and excess sulfur are formed; at cathodic potentials, sulfur is reduced to a soluble species. More importantly, excess surface sulfur is formed spontaneously under zero current conditions in alkaline solutions. This has been shown to occur on both polished surfaces and on virgin surfaces produced by in situ cleavage under the electrolyte. The photovoltage gives some insight into the charge and potential distribution at the galena surface. This is found to depend on past electrochemical history and the n- or p-type semiconducting character of the electrode and is interpreted in terms of changes in the surface stoichiometry that occur during reduction or oxidation. The effect of surface stoichiometry on subsequent xanthate interactions is discussed.

Jan 1, 1976

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

5.1 INTRODUCTION There are several types of surface ground disturbances, each of which is immediately transmitted to surface structures and causes damage of various forms, depending on the location of the structures in the subsidence basin. Many criteria have also been proposed for defining the potential structural damage. All of these topics will be discussed in this chapter. 5.2 TYPES OF GROUND DAMAGES There are two types of ground damage, continuous and dis¬continuous, that could inflict damages to surface structures. Dis¬continuous ground damage is open fractures of various degrees. Four types of fractures are commonly seen (Brauner, 1973b): 1. Fissures or cracks. Cracks are the most common form of ground damage and range from completely closed to several feet wide. Surface cracks are most prominent when the ratio of mining depth to mining height is smaller than 30 to 50 times mining height. Cracks initiate parallel to, but ahead of the moving long¬wall face at some intervals when the depth-to-mining height ratio is less than 25 to 30. As the face continues to move, they open up and then close gradually, and in most cases eventually close up completely when the face moves farther away. Sometimes when the depth-to-mining height ratio is larger, cracks may initiate be¬hind the face and go through the same cycle. Cracks are also more likely to occur in the hill when the face is moving in the uphill direction. Cracks also occur at or near both sides of the panel edges. Those cracks tend to remain open permanently. When the surface is covered with grass or other vegetation, cracks of less than 1 to 2 in. wide usually do not penetrate it and become invisible on the surface. 2. Steps. A step may occur when the longwall face stops abruptly if the mining depth-to-mining height ratio is less than 20. Steps may also occur along the panel edges. Steps also range from a few inches to a few feet in width and depth. If planes of weakness are oriented favorably, ground will slide along these planes and form steps on the surface. 3. Cave-in pits. These result from local collapse of the ground from the mine level to the surface when the mining depth is less than 150 ft and occur mostly above abandoned mined lands. They may be as large as 40 ft wide and deep. 4. Bumps (compression ridges). Bumps result from ground compression and occur mostly near panel center some time after mining. Bumps of up to 4 ft, but mostly 1 to 2 ft, have been identified. Continuous ground damage refers to the formation of the sub¬sidence basin where continuous nondestructive ground deforma¬tions occur. As mentioned earlier, continuous ground deforma¬tions associated with a subsidence basin include subsidence, slope, curvature, displacement, horizontal strain, twisting, and shearing. 5.3 TYPES OF SURFACE STRUCTURAL DAMAGES Both continuous and discontinuous ground disturbance cause damage to surface structures. A. Structural Damages Due to Discontinuous Ground Disturbance 1. Fissures or cracks. Open cracks can cause dislocation of surface structure if the gaps are sufficiently large so that the struc¬tural elements cannot resist but fail. On the other hand, minor cracks affect only the appearance, and not the structural integrity. 2. Steps. When a surface structure is located on a step, some portions of the structure lose support and become overhung. In the case of a residential house, there will likely be many open frac¬tures in the overhung portions, followed in severe cases by sepa¬ration of the superstructure at the edge of the step. 3. Cave-in pits. If the caved-in pit is larger than the surface structure, the structure will drop into the pit and become unstable. If the caved-in pit is smaller than the surface structure, the struc¬ture may either become overhung or lose support in some portions. In either case, it is unsafe for use. 4. Bumps (compression ridges). Bumps will disrupt roadways or house floor. If located under supporting members of the struc¬tures, it may cause damages. B. Structural Damage Due to Continuous Ground Disturbances 1. Subsidence. Pure subsidence or uniform subsidence over an area does not cause any structural damage. However, if it becomes a topographical low area, it may be flooded with water and make the surface structures unusable. It must be noted that the flat bottom area at the center of the final supercritical subsidence basin does not reach that position suddenly. Rather, as shown in Fig. 3.1, it is subjected to the dynamic surface deformation asso¬ciated with the traveling subsidence basin before it is left behind to be part of the flat-bottom area. Therefore any structure located at the center of the final supercritical subsidence basin must be able to resist the dynamic surface deformation in order not to be dam¬aged. 2. Slope. Ground slope will induce tilting of the structure. Tall structures with small base areas, such as water towers, chimneys, and power transmission towers are most sensitive to ground slope. If the ground slope is such that if after tilting the center of the gravity of the tilted structure falls outside the base area, it will topple, but this seldom occurs. Ground slope will change the designed slope of a buried trans¬portation pipeline, either increasing or decreasing the original slope depending on whether the ground slope coincides with or opposes the original slope. There are maximum allowable final slopes for various types of transporting materials. Ground slope also affects highways and railways. There is a maximum allowable final slope for a railway because tractive effort increases 1/1000 of its weight for every increase of 1/1000 in grade. 3. Curvature. There are positive (convex) and negative (con¬cave) curvatures. When a surface structure is located on a positive curvature, both ends become unsupported, followed by bending upward at the midportion. The top portion is subjected to more severe stretching than the lower one. As a result, vertical cracks with a wider gap at the top occur at the window, door frames, on the walls, and at -the wall joints. V-shaped cracks appear at the

Jan 1, 1992

By Thomas O. Glover

History of Underground Coal Mining in Illinois The production of coal in Illinois using underground mining methods, commenced early in the 1800&apos;s; however, the first shaft entrance was not sunk until 1842. The shafts range in depth from 16 feet (4.9 m) in Peoria County to 1,001 feet (306 m) in Christian County. The earlier mines were smell, private operations that worked outcrops and shallow seams at less than 100 feet (30.5 m) in depth. By 1975, there were reported 4,076 abandoned underground coal mines in 70 Illinois counties (Nawrot, 1977). There were many more mines; however, only 4,076 underground mines have been documented. Small mining operations characterize the majority of the underground mines. There have been no significant multiple seam operations in Illinois. The most extensively mined seams were the number two, five, and six seams. Number two seam was worked in the early 1900&apos;s by 252 mines in the longwall mining region of northern Illinois (Nawrot, 1977). Available records for 2,054 abandoned mines identify 1,043 as shaft nines, 700 as slope mines, and 311 as drift mines. Some operators began reporting annually to the State Department of Labor in 1879 and by 1882 all mine operators were reporting. Annual reporting still continues to date. The information is compiled by the State Department of Panes and Minerals in their "Annual Coal Report." By the end of 1974 there were 800,000 acres (323,756 hectares) of abandoned underground coal mine workings (Smith-Stall, 1975)2 Copies of abandoned underground coal mine maps may be inspected by interested parties in the State Department of fines and Minerals office in Springfield, Illinois, or at the office of any county recorder for mines within their county. Copies of active underground coal mine maps may be inspected at a State mine rescue station near the mine site or at the county recorder&apos;s in the county in which the mine is located. Copies of active underground coal nine naps shall be open to the examination of all interested persons, but such examination shall be made only in the presence of the State mane inspector or the recorder. At the present time, the Department of Mines and Minerals has 1,746 maps of abandoned underground coal mines in its possession. These maps cover the majority of

Jan 1, 1977

By K. K. Kohli

Since the adoption of the Surface Mining Reclamation and Control Act of 1977, which mandates that surface subsidence be an intergral part of the underground coal mine design, there has been a sudden rise of demand on guidelines for minimizing surface subsidence and its associated structural damages. Unfortunately there is no sufficient amount of systematic subsidence data to fill such a gap, although considerable research has been devoted to the subsidence-induced damages of surface structures in the past. However, it was said that many surface subsidence surveys have been performed and monitored by coal companies during the past twenty years, and that it will be a great source of information for subsidence engineering design if they can be collected and assembled together. An effort was therefore initiated in the Department of Mining Engineering, West Virginia University, under contract with the U. S. Bureau of Mines in December 1978 to contact each individual coal company in the Northern Appalachian Coal Field for any surface subsidence survey data. After 10 months&apos; survey, the data collected include 17 longwall panels and 2 room and pillar sections. The data in-each panel and section cover the complete set of subsidence survey raw data, underground mine layout maps, surface topo maps, geological loggings showing the stratigraphic sequences and thickness of the overburden, and if available, locations and types of surface structures. On-site visits were followed to study the surface terraines and structures. Interviews were conducted with the owners of the surface structures in most cases about, if any, the history and characteristics of damages.

Jan 1, 1980

By S. S. Peng

In dealing with the mining engineering problems, the traditional approaches of laboratory experimental simulations and/or analytical solutions are not very effective. Mainly because the field problems are too complex to be solved with a few simplified assumptions. Conversely it is also true that the experimental and analytical/ numerical models currently available are far from being able to model the actual cases. Under such conditions, the most effective mean of research into mining engineering problems is to combine the mine (field) investigations with laboratory and / or analytical modelings. It is with this concept in mind this research was initiated in 1973. &apos;The field investigations which began in the fall of 1978 consisted of mainly visiting the mines where surface subsidence monitorings had been or were being monitored and/or surface structural changes had occurred. From such visits, subsidence data were collected. A quick analysis of those data provided preliminary understandings of the characteristics of the surface subsidence parameters in the regions (1-5). Using those date, models of various types are being developed for subsidence prediction / control. So far, a total of 44 longwall subsidence profiles in 22 longwall panels and 10 room-and-pillar profiles in 5 room and-pillar sections have been collected. This paper summarizes the combined results published previously (1-5) and present the preliminary results of the predictive models developed.

Jan 1, 1982

By M. Martins

This work presents and discusses the influence of the surface tension (gLV) of methanol/water mixtures on the flotation response of apatite versus gangue minerals conditioned with flotation reagents (75 g/t cornstarch and 100 g/t Berol 867) at pH 10.6. Berol 867 is a collector composed of sodium alkyl sarcosinate plus nonionic surfactant. The highest Schulz efficiency of separation (recovery of apatite minus recovery of gangue) was achieved at ?51.0 mN/m. The critical surface tension of wettability (gC) of apatite was found to occur at 34.7 mN/m when determined by means of gamma flotation experiments, and it was 33.9 mN/m when determined by Zisman?s approach.

Jan 1, 2009

By A. Vilinska

The adhesion of Leptospirillum ferrooxidans bacterial cells onto the sulfide minerals pyrite and chalcopyrite was evaluated using two different physical-chemical approaches; thermodynamic and extended DLVO theory. For the parameters incorporated into calculations, the zeta potentials and contact angles of powdered solids and bacterial cells were acquired experimentally. The Hamaker constants essential for Lifshitz-van der Waals inter-action calculations were calculated following two different methods: macroscopic and microscopic. Adsorption tests were carried out at physiologic conditions to estimate the amount of cells adsorbed onto a mineral surface and the extent of alteration of that mineral surface in biobeneficiation. The free energy of adhesion was found to be negative for both minerals, indicating that the adhesion is energetically favored and preferred. The interaction energy diagrams of the total interacting force was also negative for the cases where the particles were charged oppositely; in the remaining cases, the total force was attractive after overcoming an energetic barrier caused by the repulsive electrostatic forces. Under the conditions of the adsorption test, the experimental results are in agreement with the theoretical; this suggests that the physical-chemical forces are crucial for bacterial adhesion.

Jan 1, 2011

By N. Careddu

In recent years, slabs with a rough surface have captured a large share of the ornamental stone market. However, the main technologies used for this type of treatment are based on mechanical shock (bush-hammering) or thermal treatment (flaming or flame-finishing). These traditional technologies are widely used, but have many limitations that decrease their usefulness. The purpose of this study was to develop a technology that enhances the natural colors of the rock and produces a rough surface without compromising its mechanical characteristics, in contrast to traditional technologies. This report shows the technical, economic and aesthetic results obtained with a new water-jet treatment and compares it with competing technologies.

Jul 1, 2010

By W. M. Cross

The use of fillers and reinforcements for plastics has increased considerably over the past few decades. For example, in the 1980&apos;s the average growth rate of filler use was 5.8%. [Katz and Milewski, 1987] Similar filler use growth rates occurred in the 1970&apos;s due largely to the increase in price of petrochemical starting materials for plastics. While filler use is still sometimes predicated on the cost benefits associated with their addition to the plastic, other mechanical and performance advantages associated with filler addition are being realized, and account for most of the increased usage. Plastic filler types are many and varied, and include both inorganic minerals/metals and organic compounds, with the former type being, by far, the more common. Common mineral fillers include oxides, including both natural and synthetic silica; carbonates, particularly calcium carbonate; clays such as kaolin; and silicates like mica and talc. It has been recognized that a number of factors influence filler performance, including particle size, shape, surface area, and hardness to name a few. In addition, the interaction between the filler and the plastic is of paramount importance as this interaction will determine the wettability, bonding and the adhesion between the two materials, and ultimately, the mechanical properties of the composite. Froth flotation has long been recognized as a viable process to separate different mineral types. [Leja, 1982] Prior to flotation the minerals are liberated from the ore by comminution. The mineral particle size range produced by this comminution process is typically between 300 and 10 microns. This size range is also typical of mineral fillers for plastics. The size similarity between mineral fillers and minerals concentrated by froth flotation is only one of many similarities that can be found.

Jan 1, 1997

By S. G. Haycocks, M. Karmis, C. Haycocks

Risk assessment is a primary factor in the decision to mine some near surface orebodies, such as limestone, by either surface or underground methods. Identification and quantification of risks demonstrate that environmental concerns are greater for surface operations than underground, and may include such factors as runoff, spoil piles, aesthetics, dust, and large site reclamation. Risk assessment also includes local public feeling towards surface and underground operations while considering the balance between environmental impacts and the economic effects of mining on the local community. A complete understanding of the risks involved permits a comprehensive and accurate comparison between the two mining alternatives.

Jan 1, 1992

By Ian P. G. Hutchison

12.1 INTRODUCTION This chapter deals with the tools required to design leach operations to minimize spillage from leach pads and ponds and erosion damage during flood events or prolonged wet periods. It outlines methods used to design for prolonged dry periods when water shortage can be a problem. Seasonal operational aspects such as winter shutdown and coping with spring snowmelt periods are also discussed. General criteria useful when designing pregnant and barren solution ponds are also outlined. The aim of these notes is to provide designers and operators with a simp1ified approach to developing design parameters which make effective surface water management easy to achieve without resorting to extensive or elaborate analyses. Section 12.2 briefly outlines the types of problems associated with wet climates and floods, as well as dry periods. Determination of flood design parameters is discussed in Section 12.3. Circuit water balance and pond sizing are outlined in Section 12.4. Pond design considerations are included in Section 12.5. Worked examples are included in Section 12.6. 12.2 RAINFALL/RUNOFF PROCESSES There are two types of rainfall-runoff processes that are important when designing heap leach facilities. The first of- these is the short-term, intense rainfall or snowmelt events that occur over a period of a few minutes or hours, causing flooding that can lead to erosion damage and overtopping of ponds and containment dikes. Specific problems that can manifest themselves during these events include: • Washout of access roads; • Damage to containment dikes; • Flood water contamination of circuit water; • Damage to process water ponds by perimeter erosion or overtopping and erosion; • Loss of process circuit fluid due to breaks in containment dikes or process water ponds; and • Erosion of leach pile and consequent sediment contamination of process fluid. Other types of rainfall -runoff processes that could cause problems are the long-term-(generally months-long) wet or dry periods. Extended wet periods

Jan 1, 1988