Search Documents

By J. H. Wilhelm

Continuous thickeners can be sized either from previous experience, continuous pilot-scale test results, or from batch settling tests. Although it is a relatively simple process to size full-scale thickeners when previous experience or pilot-scale operating data are available, batch testing is often the only realistic method for sizing thickeners due to time restrictions, budget limitations and availability of sample material. Many authors have, therefore, suggested means of running batch tests and analyzing the resulting data. Fundamental thickening theory had its beginning with the work o£ Coe and Clevenger(1). In order to determine the size of the thickener settling area, they proposed that a series of batch settling tests be run at various initial concentrations. The solids handling capacity at each concentration can then be determined and the lowest capacity (maximum area requirements) used to size the thickener. Kynch(2) developed a mathematical analysis in which the relationship between solids concentration and settling rate can be obtained from a single batch settling curve. Talmage and Fitch(3), Yoshioka(4)(5) and Dick(6), have enlarged upon these works to give a basis for methods of sizing thickeners.

Jan 1, 1979

By G. K. Wilson

This paper will discuss some of the more important aspects to be considered when selecting pumps for mill discharge, cyclone feed or other severe-duty applications Included will be the selection of the pump based on such factors as particle size, particle distribution, head, flow, temperature and pH Other specifics to be covered: The relationship of impeller speed, head and wear factors as they affect pump performance and wear life; the importance of selecting a pump whose performance curve best suits the application; and how the addition of service factors applied to the actual operating conditions can lead to severe operational problems such as premature wear, pump running out on curve, and exceeding horse power limitations.

Jan 1, 1996

By Leonardo Rosas Sánchez, Darío Ángel Bulla

"The two track road sector between Cisneros-Loboguerrero (having a length of 14 km and 11 short unidirectional tunnels) is a new highway still on construction located along the existing Highway Buga – Buenaventura (Colombia). Due to the steep topography, difficult geological/geotechnical conditions, the traditional portal construction approach was impossible to be implemented in eleven (11) of the twenty two (22) portals. In this specific project, the skewed portal approach was developed as the optimal and more effective solution. The construction time and costs of portals were reduced in 21 months and 75%, respectively. At the same time, the natural equilibrium of the slopes was maintained, thus, facilitating adequate safety factors along the useful life of the project. This document pretends to show a detailed design experience (and the construction of the entry portal of tunnel 11 (left)). INTRODUCTION The Cisneros-Loboguerrero project is a 14 km length dual lane highway, connecting productive zones with the Pacific Ocean along the current Bogota-Buenaventura highway as shown in Figure 1. The project is located at the northern side of the Dagua River Valley. The preliminary design suggested constructing portals under challenging topographical conditions, i.e., slope cuts having heights between 50 to 100 m (some having slopes > 100%) requiring complex developments and having very high risks.The entry portal of tunnel 11 (left) was the first portal successfully built by implementing the skewed portal approach. Later, this approach was used as a model for the construction of the other ten (10) portal having similar topographic and geotechnical conditions. The development of this new alternative provided a considerable reduction on the construction time of portals, thus relieving a critical path in this project."

Jan 1, 2016

By Leigh Freeman

This article provides an overview for a series of leadership development workshops offered through the SME Young Leaders Program. The first of these workshops, “Accelerated Development Plan,” will be held at the upcoming SME Annual Meeting in St. Louis, MO on Sunday, March 26. How does a foundation of technical competencies relate to the development of social competencies necessary for management and leadership roles in the resource sectors? Technical competencies provide the foundation for a successful career. Social competencies provide the framework on that foundation. Successful leaders will be those who develop competencies in all areas.

Jan 1, 2006

By M. R. Fletcher

Slags generated by the ferrous metals industry can he used to produce high-value ceramic materials. The properties of these ceramics can be controlled by judicious choices of composition, additives, and processing parameters. Standard methods of materials handling, such as comminution and mixing, are as applicable to slag as to any other mineralogic raw material. In this study, foundry slag was ground, homogenized, melted, and, formed to produce a glass, and then heat treated to crystallize it into a high-strength glass-ceramic. The product shows promise as a low-cost, wear-resistant tile material that (-an he custom cast. This and similar materials made from slags and natural rocks are candidates for use as construction materials, acid-resistant piping, shock-resistant sheathing, rot-proof pilings, and, when foamed, even as pontoons.

Jan 1, 1990

By M. R. Fletcher

Slags generated by the ferrous-metals industry can be used to produce high-tech ceramic materials. The properties of these ceramics can be controlled by judicious choices of composition, additives, and processing parameters. Standard methods of materials handling, such as comminution and mixing, are as applicable to slag as to any other mineralogic raw material. In this study, foundry slag was ground, homogenized, melted and formed to produce a glass, and then heat treated to crystallize it into a high-strength glass-ceramic. The product shows promise as a low-cost wear-resistant tile material which can be custom cast. This and similar materials, made from slags and natural rocks, are candidates for use as construction materials, acid-resistant piping, shock-resistant sheathing, rot-proof pilings, and, when foamed, even as pontoons.

Jan 1, 1988

By Lauren M. Roberts, Ralph R. Sacrison

Pipeline or borehole free-fall transfer of material has long been done in support of underground mining. This paper addresses some characteristics and design elements in selecting systems suitable to the transferred media and the mine requirements. Though aspects of overall systems are discussed, principal attention is directed to the slickline/dropline/transfer line and the discharge diverter/rockbox/energy dissipator/boot. These terms are common to these systems, often used interchangeably, and will be used as appropriate to the material, equipment and construction. Following several design sections, fabrication and construction, and system operating and maintenance procedures are discussed.

Feb 1, 2025

By J. Tuzson, H. McL. Clark

Introduction Wear of pumps, wet cyclones and pipelines by suspended solid particles will impact their operating economies by limiting their useful life, reducing their reliability and increasing the amount of servicing. Erosion is considered a materials problem. The empirical solution consists of testing different materials in field applications. Such tests are time consuming and expensive. The prediction of localized wear rates, life estimates and appropriate material selection demand a better understanding of the slurry wear process in environments corresponding to those found in working equipment. Key words: Wear, Slurry abrasion, Coriolis erosion tester The slurry wear process Solid particles suspended in liquid generally move with the flow, but such particles deviate under the centrifugal and Coriolis forces encountered in pumps. The concentration of particles will increase, and a solid layer or bed may accumulate if the acceleration is directed against the flow passage wall. Large particles in dilute suspensions may impact the wall. dissipating their kinetic energies and removing material. However, particles smaller than about 11)(1 µm encounter great drag when moving through the liquid. and such par¬ticles have little kinetic energy left when they reach the wall. They cannot penetrate the stagnant boundary layers present in pumps. Therefore, small particles tend to form beds that slide along the wall, removing material by a process that could he called sliding erosion or wet abrasion. Wear by impact erosion from large particles in dilute slurries can he predicted by appropriate analytical and empirical methods. However, laboratory tests and calculations of wear rates that correspond to sliding erosion are more likely to correlate with field experience from wear under similar conditions. Specific energy Data from laboratory slurry erosion experiments have shown that the amount of material removed is approximately in proportion to the energy expended in the erosion process. Thus. the specific energy-energy expended in removing by erosion a unit volume of material-offers a simple, practical measure for the erosion resistance of materials. The concept was found to also apply to sliding erosion (Clark et al.. 1997). Generally, the study of the material-removal process in slurry erosion continues to remain a subject of research. Conceptually, if the flow velocities and accelerations could be calculated in a pump or pipeline, the energy dissipated at the passage walls could also be estimated, and the material removal rate would become known from the specific energy determined by laboratory tests. Slurry erosion testing Laboratory devices made specifically for slurry erosion testing may be grouped into the following: jet erosion devices, slurry pots and the Coriolis test machine (Pagalthivarthi and Helmly, 1992). Jet erosion devices use a slurry pump and nozzle to produce a high-velocity slurry jet that is directed at a flat material specimen, either perpendicularly or at some acute angle. Combined impact and sliding erosion are produced. but the processes cannot be separated, and the wear is difficult to assess except by weighing. Slurry pots consist of a cylindrical vessel containing the slurry of interest. In the slurry pot, test specimens are attached to a rotating arm. The samples are rotated in the slurry and experience local flow conditions that result in combined impact and sliding erosion. Wear depth measurements from detailed laboratory experiments have been successfully correlated with results from an analytical model of the process, and specific energy values have been calculated (Wong and Clark, 1995). In industrial use, the samples are weighed to determine the total material loss. Materials are ranked with respect to some reference material. The Coriolis erosion tester (Tuzson, 1984) consists of a rotor with a central cavity, from which two opposing radial passages lead out (Fig. 1). The slurry is fed to the centerof the rotor in one pass from a stirred overhead tank. The slurry particles are subjected to the Coriolis acceleration as they flow out through the radial passages. The material specimens are mounted into the radial passage walls facing the direction of rotation and are eroded by the particles that are pressed against them as they flow out radially. A narrow groove is worn into the sample within a few minutes, using a few gallons of slurry. Material removal is estimated accurately from profilometer traverses across the wear scar at different locations. The energy dissipated by the particles can be estimated, which leads to a well-defined experimental value for the specific energy.

Jan 1, 2000

By William D. Leech, Peter S. Buskirk

Virginia Electric and Power Company commencing in early 1985 will begin operating the Bath County Pumped Storage hydroelectric facility, presently the largest capacity installation of its kind. Six concrete lined vertical shafts, 3 ea x 44.0 ft (13.4m) diam x 330 ft (100m) and 3 ea x 28.5 ft (8.7m) diam x 740 ft (226m), comprise a portion of the three underground power conduits. The project team decided to employ the slipform over the conventional jump form method. This selection was based on the engineer's hydraulic design and the contractor's performance requirements. This paper presents the key elements of the shafts' successful slipform operations. The contractor achieved slip rates as high as 60 ft (18m) per day; and the owner received competent permanent linings as specified by the engineer. The authors describe the team's effort to progressively improve both concrete quality and placement rate.

Jan 1, 1985

By Jed Greenwood, Lyall Workman, Michael Haggerty, Russell Sheets

Draglines often work from a position on the active highwall or spoil side bench to remove undisturbed waste material and spoil in the previously mined pit. To protect the dragline crew members and the machine, it is necessary that the highwall remain stable while the dragline is present on the bench. In the past several years, we have been involved in determining the causes for highwall failures that included the dragline. While there have been no injuries and limited dragline damage with these incidents, the potential certainly exists for a more serious outcome. In all cases, the operation had completed a geotechnical study to support the ground control plan and pit designs. However, all these incidents included aspects that would not likely have been identified in studies to determine highwall and spoil designs to support ground control procedures. In general, these events included aspects that were localized and would have been difficult to identify in initial slope stability studies either observationally or during the soil testing and modelling efforts. Although the authors do not have quantitative evidence of this, it does seem there has been an increased number of events in recent years. This may be due to loss of institutional knowledge, mining in more challenging areas, or simply an increase in localized variation. This paper will describe some of the issues we have seen and what the causes of failure were. It becomes clear that avoiding similar incidents in the future requires on-going observation and inspection of active highwalls and spoil benches to try and identify local variability and impact on mining. The information can proactively be used to update stability modeling of any concerning issues to determine likelihood of problems and to develop solutions.

Feb 1, 2025

By E. Medina, W. Callupe, R. Sharon

Slope stability in Barrick’s Pierina Mine open pit is significantly influenced by the structural geology, the variably argillized rock mass, and locally by perched groundwater. Development of an extensive surface water diversion network continues at Pierina, which is necessary to minimize highwall and adjacent natural landslide movement and erosion during the wet season. Slope movements are effectively monitored using optical survey methods, strobe light extensometers, gap monitors, and piezometers. The slope stability program at Pierina is focused on improving the understanding of the stability mechanisms in order to ensure continuous safe operating conditions. Priorities are placed on developing an accurate detailed engineering geological model, enhancing groundwater depressurization, and optimizing highwall controlled blasting procedures.

Jan 1, 2003

By Thomas A. Simpson

Hydrogeological techniques were used to solve problems of slope stability in open-pit mines of the Eufaula bauxite district, Alabama. Geologic and hydrologic data were evaluated and used to design a system of dewatering wells to enable the operators to mine bauxite more efficiently and economically. Walls of open-pit mines in the district were subsequently stabilized by the operation of the dewatering system. Three open-pit mines, each at varying stages of the mining process, of the A. P. Green Refractories Company, were used to develop a sequential series of guidelines that indicate how to effectively remove ground water from the formations surrounding the ore bodies in the district. The use of sound engineering principles in well design, in combination with the correct interpretation of the pit hydrology provided the basis for solutions of the slope- stabilization problem aided in the economical removal of bauxite from mines of the district.

Jan 1, 1975

By Joseph W. Siefke

The Kramer borate deposit is located in the western Mojave Desert at Boron, California, about 100 miles northeast of Los Angeles (Figure 1). The deposit derives its name from the district in which it lies. Borax (Na2 B407.10H2O) is being mined from the Boron open pit to serve a major portion of the United States and world borate markets. This paper deals primarily with those geologic factors which affect slope stability in the overburden at the Boron open pit. Discussion includes slope failure history, slope monitoring techniques and the results of a dipmeter survey of overburden structure. Open pit mining was begun at Boron in 1957. The initial pit was successfully excavated at the recommended 1.5:1 (horizontal to vertical) slope in the overburden. During pit expansion in 1962, excavation of the overburden exposed beds dipping into the pit at +15 degrees and numerous high angle fractures associated with two intersecting fracture systems, the West Jenifer and Portal fault zones. Ensuing south and east wall failures indicated the need for more structural information in the arkose to establish better wall design criteria. Barnard and Kistler (1963) recognized that the many facies changes, faults and other variables in the Boron overburden make it extremely difficult to reduce prediction of slides to a simple arithmetical formula. Despite the difficulties and uncertain¬ties, special programs such as surface resistivity, refraction seismic and core drilling were conducted in an attempt to predict slope stability conditions and to gather geologic information. These early efforts while helpful, did not provide the necessary details of bedding orientations and fault locations which are of paramount importance in our slope stability program. A dipmeter survey in 1974 successfully measured these variables and data from that survey are instrumental in the design of slopes currently being excavated.

Jan 1, 1976

By V. G. Matziaris

The differentiation between saturated and un-saturated soils becomes necessary due to basic differences in their nature and engineering behavior. The most important difference is the existence of a suction zone, above the water table, in unsaturated soils. Pore water pressure in this zone is always negative and the shear strength is greater than the one in saturated soils. This is due to an occasional and apparent component in the Mohr-Coulomb equation, which appears in unsaturated soils. In slope stability analysis of unsaturated soils, the factor of safety increases due to this occasional cohesion component of the shear strength. However, the suction zone tends to disappear because of rainfall. In these cases the factor of safety decreases and eventually the slope may fail. In this article, a parametric study of the effect of suction zone fluctuation due to precipitation in slope stability is examined. For this purpose a Combined Hydrology and Stability Model (CHASM) has been applied.

Jan 1, 2005

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

By J. L. Workman

The stability of spoil and highwall slopes are important to successful strip mining. This paper discusses soil parameters of importance in stability analysis. The common mechanisms of spoil failure are discussed. Modes of highwall failure are also outlined. The importance of water to stability is presented. Dragline mining methods most suited to creating spoil and highwall profiles that address stability needs are provided. It is concluded that groundwater and surface runoff must be well controlled, and that it will often be necessary to modify spoil and highwall configurations to achieve a stable overall slope angle.

Jan 1, 1996

By J. Andrew Leach, Robert T. Tape, Thomas G. Harper

A practical approach to elope stability design of heap leaches up to 90 m (300 ft) high is presented based on recent experiences with heaps throughout the Western U.S. Shear strength parameters for foundations, ore and liner systems are considered, with particular attention given to frictional contacts between geomembranes and clay or geotextiles. Stability of both ore and containment dikes is discussed including the effects of seismicity, staged dike construction, progressive heap development and in-heap solution levels. Design criteria and methods of analyses are presented along with techniques for improving stability.

Jan 1, 1987

By Carl D. Broadbent

The goal of slope mechanics is to achieve efficient and safe pit slopes. In the case of ultimate mine slopes the objective is to minimize the stripping ratio by steepening the slopes to their maximum stable limit. On the other hand, the inclination of working slopes is normally established by operating space requirements and the function of slope mechanics should be the continuous surveillance of slope conditions to assure long-term stability and to provide timely warning of impending slides so that corrective measures may be incorporated in production planning. In 1956 Kennecott instituted a program to provide the resources necessary to develop and maintain a slope mechanics capability, including technical knowledge, engineers, and instruments. Although the goal has not been fully achieved, very significant progress has been made. Other papers (3, 4, 7, 8, & 12) have described the purposes and detailed results of the most recent study carried out at the Kimbley Pit. The study has provided valuable experience and has given the industry a three dimensional picture of the stability variables that influence a mine slope. The study has better defined those areas which require further investigation and has indicated those design and analytical techniques which can be used with confidence. In effect, the study has paved the way for the next step; that of refining the design process and applying it for profit.

Jan 1, 1968

By M. Jaramillo

The Expanded West Pit of the 15 MTY El Cerrejon Mine will reach a maximum depth of270 m. Slope stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization call for anchoring the footwall by installation of cable bolts, 9 to 33 m long, of multi-strand steel cable. For each of the 15 m high mining benches, a row of bolts is installed with variable horizontal spacing, depending on dip magnitude. Cable bolting is now standard operating practice and 11800 bolts will have been installed during the life of the mine.

Jan 1, 1995

By M. Jaramillo

The expanded west pit of the 15 Mta (13.6 stpy) El Cerrejon mine will eventually reach a maximum depth of 270 m (890 ft). Slope-stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization calls for anchoring the footwall by the installation of 9- to 33-m- (30- to 108 ft-) long multistrand steel cable bolts. For each of the 15-m- (50-ft-) high mining benches, a row of bolts is installed with variable horizontal spacing, depending on the dip magnitude. Cable bolting is now standard operating practice, and an estimated 11,800 bolts will be installed during the life of the mine. Results to date have been satisfactory in terms of the stability condition of the bolted slopes.

Jan 1, 1997