Search Documents

By S. W. Clark, R. Meglen

A seismic refraction survey of selected environs of Brewster Phosphate's Lonesome mine near Bradley, FL identified various layers of overburden, minable matrix (ore body) and basement (i.e., bedrock) that correlated with core logs. Bivariate correlation procedures determined that statistical relations existed between mining parameters and seismic velocities. For instance, a correlation of approximately -0.6 was inferred between P wave velocity and ore grade.

Jan 1, 1990

By J. Chai, H. H. Sedarat, Gary J. E. Kramer, A. Kozak

Precast concrete segmental lining systems have been gaining widespread use in seismically active areas and a single-pass version of such a system has been developed for use on the Silicon Valley Rapid Transit (SVRT) Project in San Jose, California. The response of tunnel linings to seismic shaking is often predicted using engineering judgment, elastic closed-form solutions and numerical modeling. Such analyses generally assume a continuous structural system and hence do not explicitly model the behavior of the jointed segmental lining. A number of analyses were performed to predict radial and circumferential joint behavior during seismic ovaling and wave propagation. These analyses included a complex, three-dimensional finite element based ground-structure interaction model that incorporates inelastic constitutive soil behavior, cracked concrete properties and no-tension, frictional segment joint surfaces. The paper discusses the results of the analyses and provides guidelines for the design of precast systems in zones of high seismicity.

Jan 1, 2007

By Neil and Associates

Seismic tomography is one of several additions to the suite of geotechnical engineering tools for use in various underground rock and mineral geologic structures. Seismic tomography is a method for reconstructing a cross section of an object based on attributes of seismic energy that have been transmitted through the object. The in-seam seismic tomogram provides a dataset that can be graphically portrayed in a color-coded format that is then used to infer relative stress concentration (Fig. 1). During the past several years, the US Bureau of Mines (USBM) at its Denver, CO and Twin Cities Research Centers in Minnesota funded several innovative hardware and software developments. These were directed toward use of in-seam seismic tomography for underground geologic strata evaluations. These preliminary investigations have matured into well-defined and field-proven technical advances for improving ground-control decision making in the mining industry.

Jan 1, 1996

By D. K. Denton, D. F. Scott, T. J. Williams

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, de¬tect hazardous ground conditions and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep, >1,220-m (>4,000¬ft), underground pillars. If high¬stress areas are detected, they can be destressed prior to development or they can be avoided High-stress ar¬eas can be monitored with succes¬sive seismic surveys to determine if stress decreases to a level where de¬velopment can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost¬effective, efficient and noninvasive. Also, investigators can monitor large rock masses, as well as moni¬tor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer envi¬ronment.

Jan 1, 2000

By Jozef Descour, Kazunori Nishioka, David M. Neil

Designers, engineers, and contractors are using three-dimensional seismic tomography for geotechnical site investigations and during tunnel excavation for hard rock and soft ground applications. Utilizing multiple types of seismic signals produced by a TBM, drill, or impact breaker, the reflection of different velocity features are processed into a holographic image of the actual structure to be encountered. The Mill Creek Phase 3 alignment in Cleveland, Ohio, was imaged to define existing conditions along a 1,200-ft section of a proposed 6.1-m (20-ft) diameter CSO tunnel and, specifically, a zone of expected anomalous conditions where drilling was inconclusive. In Japan, Kajima Corporation used TRT™ to image a number of tunnels including the Fujikawa and Kanaya tunnels in a combination of methods to map structural features along the alignment.

Jan 1, 2001

By K. Y. Haramy, E. C. Westman

Anomalous geologic or stress conditions ahead of a longwall face have the potential of causing great harm to both the individual miner and the mining operation as a whole. NSA Engineering has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of afield effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration that was likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with the laboratory measurements.

Jan 1, 1997

Anomalous geologic or stress conditions ahead of the longwall face can cause great harm to both the individual miner and the mining operation as a whole. The U.S. Bureau of Mines has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of a field effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure, and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration, likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with laboratory measurements.

Jan 1, 1995

By Bill Cain, R. John Caulfield, D. Scott Kieffer

The East Bay Municipal Utility District is undertaking seismic upgrades of the Claremont Tunnel in the San Francisco Bay area. The tunnel carries treated water across the active Hayward Fault to supply a major metropolitan area. Studies indicate the tunnel could be severed by fault offset during a major seismic event. A design approach to achieve limited operation of the tunnel following fault displacement has been established and design details are currently being evaluated. This paper describes the project, the design approach, and summarizes significant construction constraints.

Jan 1, 2001

By F. R. Corwin, M. S. King, R. W. Zimmerman

A model has been developed to relate the velocities of seismic waves in unconsolidated permafrost to the porosity and the extent of freezing. The permafrost is idealized as an assemblage of spherical quartz grains imbedded in a matrix which itself is composed of spherical water inclusions in ice. The theory of Kuster and Toksöaz, based on wave-scattering considerations, is used to determine the effective elastic moduli, and hence the wave speeds. The model predicts Vp and Vs to be decreasing functions of both the porosity and the water/ice ratio, and Vp/Vs to be an increasing function of these two parameters. The theory has been applied to laboratory measurements of shear and compressional wave velocities in thirty-three permafrost samples from different sites in the North American Arctic. Although no direct measurements were made of the extents of freezing in these samples, the data are consistent with the predictions of the model. The theory can be used to infer the extent of freezing of the water in the pore spaces, based on knowledge of the porosity and either of the two wave speeds.

Jan 1, 1986

By Vincent J. Murphy

INTRODUCTION Geophysical applications to engineering projects are usually considered for reconnaissance exploration, and for some preliminary design phases. Recent experience indicates a growing need and a greater number of requests for measurements during construction. This is particularly true where seismic velocity values are related to strength properties of rock. Typical project objectives during construction are: dike and tunnel realignments required by surprise conditions encountered during foundation preparation; checks on grouting effectiveness which require velocity measurements before and after grouting; and dynamic moduli measurements along the walls of tunnels and deep excavations. This paper considers one of the on-site seismic applications that is rather simple and straightforward, and yet has few references in the literature. The specific objective is the measurement of seismic velocities (both "P" waves and "S" waves) for determining the thicknesses and dynamic moduli values of loosened zones of tunnel wall rock. PRE-EXCAVATION SEISMIC METHODS The seismic methods suitable for engineering project studies are well known and especially suited for routine site reconnaissance; these are illustrated in Fig. 1. The seismic refraction profile with a

Jan 1, 1997

Passive seismic monitoring is a useful tool for measuring wave propagation in rock mass in deep underground mining. About 20000 mining ? induced seismic events of a hard rock mine, are identified and investigated. The travel times of source-receiver pairs allow us to demonstrate temporal change in velocity. It was found that the average P wave velocity is about 6000 m/s in the mining regions. Velocity investigations on the data during about three months around the main shocks show a significant decrease of the average seismic wave velocity after the main shocks. The sudden drop of average velocity change after the main shocks implies the creation of new fractures in the rock mass due to the main shocks. Afterward, the average velocity increased to a normal level after a time duration of several days. A reasonable explanation for the post seismic velocity increase is that opened cracks begin to close due to crack healing.

Feb 23, 2014

By B. H. Richard, P. J. Wolfe, T. G. Holdeman

Guided seismic wave propagation was studied in the Lower Freeport (6A) coal seam in the Oak Park No. 7 mine near Cadiz, OH. Three component geophones were implanted in the coal at distances ranging from 72 m to 183 m from the seismic source. Both Love- and Rayleigh-type modes were observed but the Love-type mode produced the best data. Detailed analysis was performed on the best Love data and a Dziewonski map of group velocity vs. frequency was constructed. This map was in excellent agreement with a theoretical dispersion curve calculated for a model of the coal seam. The Love wave group velocity was found to have a minimum value of 510 m/sec at 275 Hz. Only the fundamental mode contributed significantly to the observed signal and it was observed up to the maximum distance available.

Jan 1, 1987

By B. Ollila, L. Brown

As mining fronts converge in sill pillar extraction, the mine seismic hazard can be significantly altered and large seismic events have been known to occur. This study used common seismological tools to analyze the extraction of highly stressed sills from two deep Canadian mines with the objective of characterizing the rock mass failure process and relation to large seismic events. The approach treated a sill pillar as a mine-scale failure process, meaning the temporal and spatial analysis scales needed to exist on a similar scale to a significant part of the mine. The temporal analysis scale overlapped with the entire mining sequence, included several years of data to establish long term change in the characteristics of rock mass failure. The spatial analysis scale included the rock mass surrounding a large part of the convergent mining sequence. To accommodate the large spatial and temporal scales, the highest magnitude 2% of events in the dataset were analyzed. Similar results were shown for sill pillars in both mines. Changes in event location, time, magnitude, energy index and apparent volume were similar to expected behavior of rock failure. Indications of strain hardening and strain softening were observed in the sills. The hardening period was characterized by a high rate of small events, high energy index and low apparent volume, giving an indication of high stress and low rock yield. The softening phase was characterized by a decrease in the rate of small events concurrent with an increase in the rate of large events, low energy index and high apparent volume, indicative of release of stress and increase in deformation. Large magnitude seismicity was strongly related to the softening phase, with several Nuttli magnitude 3.0+ events occurring shortly after the transition from hardening to softening failure regimes. Sill failure was indicated by consistently low EI and low levels of seismicity and seismic hazard in the sill pillar.

Apr 26, 2022

By A. Iannacchione

Longwall mining began within the Pittsburgh coalbed of Pennsylvania (PA) in the early 1970?s. Originally, longwall mine layouts were designed to fit within existing room-and-pillar operations, where panels were limited to that of typical production panels, e.g. a few hundred feet wide by a few thousand feet long. In these early designs, the gate entries were comprised of chain pillars similar to those found along main entry systems or within pillar recovery sections. The modern longwall mine has little in common with their 1970?s predecessors. Today the entire mine layout is designed around the longwall mining method. The longwall panels have grown to well over one thousand feet in width with lengths now measured in miles. In addition, development pillar sizes and shapes are matched to specific performance requirements.

Feb 27, 2013

By Carl H. Eckert, James P. Berson

INTRODUCTION The demand for specialty metals in industrial applications is in it's healthiest state since the late 1970'8, and several specific markets are recording record sales. Such metals as gold, silver, zirconim., titanium, beryllium, gallium, germanium, the platinum group, and the lanthanides accounted for sales in excess of $2 billion in 1985 among the end uses covered in this report. Although specialty metals as a group have suffered the effects of recessionary pressures in the past, these metals have proved more resiliant than such large volume metals as copper and nickel. This is due to the unique physical properties they possess which makes the threat of substitution or replacement through technological development uneconomic. The outlook for these specialty metals is optimistic in electronics, catalysts, ceramics, and alloys, and their specialty status results .in a combined average annual growth in demand of 7% through 1990. WHAT MAKES THESE METALS SPECIAL? Such characteristics as electrical conductivity, corrosion resistance, catalytic activity, thermal stability, and optical properties allow the term specialty to be applied to these metals. More importantly, all of these metals possess more than one of these qualities, as shown in Table 1. [ ] These five major functions are important in the end uses for these metals, although the specific applications vary somewhat. Conductivity in term of low or high electrical resistance is of obvious importance to electronics manufacturers. Producers of circuit boards or semiconductors require such metals as gold, palladium, platinum, and gallium due to their low electrical resistivity. However, these producers also require such metals as beryllium in the oxide form for insulation components because of the compound's low electrical conductivity. Although the lanthanides' conductive characteristics are not particularly attractive in electronics, they are of great importance to alloy manufacturers producing permanent magnets for automotive and computer applications. Corrosion and wear resistant properties are extremely attractive to a number of end-use industries, particularly in view of the estimate by the United States Bureau of Mines that $10 to $50 billion in losses are experienced by U.S. industry due to equipment corrosion and $100 billion due to equipment wear. The strength of high purity titanium and zirconium make these metals the obvious choice for corrosion and wear resistance particularly in the chemical processing industry, where the ability to maintain integrity in corrosive environments is a must. Heat exchangers, nuclear control rods, and a number of parts in jet engines have benefited greatly from the use of these metals. However, such other specialty metals as beryllium, and the lanthanides also improve the wear or corrosion resistance in various products. For example, a beryllium-copper alloy contact maintains it's spring like character, and does not loose this character after repeated use, which could result in the loss of an electrical contact. Lanthanide, in the form of cerium oxide, is commonly employed in alloys used to produce catalytic converter casings for the purpose of reducing damage by corrosive road salt. In some instances, the catalytic activity of several of the specialty metals assists in the economic production of other materials. However, the importance of specialty metals in catalysts is most apparent in catalytic converters for emission control. Platinum, palladium, and rhodium are

Jan 1, 1986

By Leroy O. Gieseke, John B. Begley

If the particles produced and transported in your plant are as chunky as rough crushed coal or as fine as cement, there are probably several conveying and elevating systems suitable for your operation. The problem is deciding which is most suitable in terms of space, energy cost, allowable product degradation, productivity, and angle of movement. Each conveying and elevating method should be fit to the products it can handle successfully, to desirable economics, and to suitability for the overall operating scheme. Matching along these lines will result in selection guides that should be useful for many years, although design evolution is expected for the materials handling equipment involved. There are several common bulk material handling devices for moving solids: belt conveyors, screw conveyors, bucket elevators, chain conveyors, and en-masse conveyors/ elevators. En-masse conveyor/elevator equipment is commonly compared and contrasted with the other devices. These comparisons often involve en-masse versus all others. En-masse has developed into a versatile technique because the machines can move materials horizontally, vertically, or in closed circuit. Such machines unload, elevate, store, reclaim, and distribute materials-all without ancillary equipment except for chutes and gates. Bulk material can be carried, as with a belt conveyor or bucket elevator; pushed, as with a flight or screw conveyor; bumped, as with a vibrating conveyor; blown, as with a pneumatic conveyor; fluidized, as with a dense phase pneumatic conveyor; or by applying internal forces to it to induce "en-masse" flow. Conveying en-masse is analogous to the flow of a fluid in an open channel, and elevating en-masse is analogous to the flow of fluid in a pipe. In the case of a fluid, flow is caused by a differential in pressure. With en-masse movement, flow results from resistance to shear induced by the movement of chain and flights.

Jan 12, 1980

By David van Cleave, David L. Rome

Whether you buy your minicomputer from a manufacturer or another vendor, the first thing you must do is define your needs. With good planning, the initial cost will be low and your return on investment will be maximized over the long term. Involving all members of your staff who will he using the new computer in the planning phase is also important. Their participation will alleviate any potential concerns they may have about new equipment, and their suggestions will provide valuable input for your specifications. After you define your proposed system, survey available hardware and software. The survey will help you in the next step, preparation of specifications. The specifications, along with a quote request, are then sent to various manufacturers. Consider the Manufacturer When selecting your minicomputer, one important item to consider is the manufacturer. Remember, when you buy a computer, you're also buying the services of a computer company. A firm that makes a commitment to its customers and provides a product that is field tested before releasing it for sale is preferable. Examine the company's maintenance and support packages, since every machine requires preventive maintenance. Does your manufacturer or original equipment manufacturer (OEM) support service sites in your area? Has their service record been commendable? Will they provide training for your personnel and a supply of circuit boards so you can retain a degree of self-service autonomy? Three methods of buying a computer involve the manufacturer, an OEM, and the systems house. Buying direct from the manufacturer means you go straight to the source, using no middleman. This gives you maximum flexibility; you can consider every alternative and many possible combinations of computers, peripherals, and software until you find exactly the right system for you. The OEM buys computers direct from the manufacturer and builds them into his own computerized, special purpose product. He usually sells a complete package, including software and hardware, and often noncompetitive equipment as well (a scientific or engineering instrument, for example), designed for the mining market. Because he offers a packaged product, the OEM can often charge less for the system than if you put the pieces together yourself. In many ways, the OEM also provides a unique system. And while the OEM sells a packaged solution, he also usually has the special market knowledge necessary to modify the system to meet your unique needs, if necessary.

Jan 11, 1981

By Paul L. Russell, R. G. K. Morrison

9.1-CLASSIFICATION OF MINERAL DEPOSITS AND ROCK MATERIALS After a mineral deposit has been discovered, delineated and evaluated, the next step is to select a mining method that is physically, economically and environ- mentally adaptable to recovering the mineral from the deposit. The term "mineral deposit" is used to denote a concentration of mineral (including rock and coal). Even where there is considerable past experience available, many of the critical design criteria must be determined utilizing only information obtained from an examination of exploratory drill core specimens. The factors that affect this selection are as follows: (1) the spatial characteristics of the deposit (size, shape, attitude and depth); (2) the physical (or mechanical) properties of the mineral deposit and surrounding rock; (3) ground water and hydraulic conditions; (4) economic factors, including grade of the ore. comparative mining costs and desired production rates; and (5) environmental factors, such as the preservation of the surface overlying the mine, and the prevention of air and water pollutants. Of these factors, the spatial characteristics of the deposit and the physical (or mechanical) properties of the mineral and surrounding rock limit the methods that can be employed to mine it. Six types of mineral deposits are recognized, as follows: 1. Massive-A deposit of considerable lateral and vertical extent in which mineralization (or ore) is relatively uniformly distributed. Disseminated copper ores are typical deposits. Dome salt also is included in this classification. 2. Bedded or Tabular-A mineral deposit that parallels the stratification, most often in sedimentary rock, usually laterally extensive, and of limited thickness. Most coal measures and some evaporite mineral deposits (e.g., potash) fall in this class. 3. Narrow Vein-A zone or belt of mineralization (ore) typically long, narrow (less than 10 ft), often dipping steeply, and usually lying within boundaries separating it from neigh- boring rock. Many gold and other metallic minerals occur in narrow veins. 4. Wide Vein-As defined under narrow vein except that the vein thickness is greater than 10 ft. 5. Lentictclar or Pocket-An isolated ore body, or an enrichment of limited vertical and horizontal extent in a massive, bedded or vein deposit. Lead, zinc and iron ores often occur in this type of deposit. 6. Placer-A surface or near-surface deposit, usually tabular and may be of consider- able areal extent, containing mineral particles (e.g., gold, platinum) in detritus (e.g., sand, gravel). The rock materials associated with mineral deposits are classified as follows: 1. Detritus-Sediments and other accumulations of solid particles produced by the mechanical and/or chemical disintegration of rocks, and usually having a low cohesive strength and very low compressive strength (e.g.. soil, sand, gravel, alluvium, playa). 2. Jointed and Fractured-Unbonded-A rock mass, often occurring on or near the surface or in fault zones, in which the joints or fractures contain alteration or decomposition

Jan 1, 1973

By Sheldon Shepherd

Fifty years ago, belt scales were mechanical devices based on a complex weight balancing design. Today's systems use load cells to assess material weight, belt speed sensors and microprocessor-based integrators to continuously compute the rate of material transferred along a conveyor. Belt scales have become important assets to a plant. They help maximize the use of raw materials, control inventories and aid in the manufacture of a consistent product. Choosing and installing a belt scale system may seem complicated but it can be simplified by following a few guidelines.

Jan 1, 1999

By N. B. Pundari

Proper selection of large walking draglines, based on sound engineering principles and field experience, has not kept pace with the large capital expenditures needed to buy these stripping machines. The use of large walking draglines for stripping overburden in US surface coal mines grows steadily, but equipment selection continues to pose problems. An improper size, model, make, or spoil reach selected for a particular stripping application results in additional, unnecessary coal production costs. Large walking draglines are being used to dig deeper tar sands at the Syncrude operations near Fort McMurray in Northern Alberta, Canada. This application is compared with typical deep digging operations and dragline use prevalent at typical US strip mines.

Jan 4, 1981