Search Documents

By J. Cygankiewicz

Efficient prevention of mine fires is impossible without predicting the self heating processes in the given geological and mining conditions. The respective forecasting method is presented in this paper based on the following assumptions: - factor deciding on fire hazard in the underground workings is the process of heating of coal from the primary rock temperature to the critical temperature when the heating rate growth rapidly - another important factor is the fire incubation time defined as time needed to achieve the critical temperature. This time is determined by balance of heat and mass in the heated coal - contact of crushed coal with oxygen in air cause some exothermic processes as : physical and chemical sorption of oxygen , oxidation reaction and evaporation of humidity Heated coal transfers its thermal energy to the environment by conductivity to the rocks and by convection to the flowing gases. The heating is possible if thermal energy generated from coal is greater then the share transferred to the environment. The paper presents the laboratory method of measurement of heat generation in adiabatic conditions. Also the mathematical model with examples of computation enabling to forecast the self heating process of crushed coal is presented.

Jan 1, 2003

By J. E. Quintanilha de Menezes, L. Ribeiro e Sousa, I. Ferreira

The Paradela dam has a spillway that makes it possible to discharge a maximum flow of 400 m3/s, the water discharges being on the river Sela, about 2km upstream the river Cávado. After the first use of the spillway, some landslides have occurred on the right bank of the river Sela as a result of the erosion generated on its base about one hundred meters near some houses of a small village. This paper presents a study performed for the slope stability where finite element results are taken into account. A monitoring program was established that essentially consisted of measuring sub-horizontal displacements in points located in boreholes at different depths and also phreatic levels. Some monitoring results are presented. Le barrage de Paradela a une décharge d’eau avec un débit maximal de 400 m3/s sur le fleuve Sela dans un endroit situé environ 2km sur l'amont du fleuve Cávado. Après la première utilisation de cette décharge, quelques glissements se sont vérifiés sur le versant droit du fleuve Sela résultant de l’érosion générée sur sa base dans une zone à 100 mètres de quelques maisons d’un petit village. Ce travail présente une étude réalisée concernant la stabilité du versant avec la considération des résultats des éléments finis. Un programme d’auscultation a été mis en place pour mesurer les déplacements sub-horizontales sur des points situés en forages à des différentes profondeurs. Quelques résultats de cette monitorization sont présentés. Der Ueberlauf des Padela Dammes ermoeglicht das Ablassen einer max. Wassermenge on 400 m3/s in den Sela Fluss, ca. 2 km flussaufwaerts des Cávado Flusses. Nach Inbetriebnahme des Ueberlaufes traten in ca. hundert Meter Entfernung zur Wohnbebauung eine Dorfes Erdrutschungen am rechten Ufer des Sela Flusses auf, die auf Erosionen am Flussbett zurückzuführen waren. In der vorliegenden Studie wurde die Boeschungsstabilitaet unter Beruecksichtigung von Berechnungsergebnissen der Finiten Element Methode untersucht. Es wurde ein essprogramm ausgearbeiten, das im Wesentlichen auf Messungen der Untergrundverformungen in verschiedenen Bohrlochteufen sowie auf Grundwassermessungen beruht. Im Folgenden sind einige Messergebnisse dargestellt.

Jan 1, 2003

By R. J. Dippenaar

In his inaugural lecture (delivered in Afrikaans at the University of Pretoria on 16th February, 1995), Professor Dippenaar defends his doctrine, philosophy, objectives, and methodology, as was required of a newly appointed professor in the days of old. Briefly, he recounts the growth and achievements of the Department of Material Science and Metallurgical Engineering at the University of Pretoria; he sketches its strategic guidelines and the obstacles encountered; he outlines the opportunities for the metallurgical industry in South Africa and the need for environmental control; and he describes how modeling techniques, together with expert systems, can aid both the industry and the community. He ends on an optimistic note, saying that his Department will continue to strive to transform adversities into opportunities, and to give its students a view of new horizons beyond the foundations laid by their teachers.

Jan 1, 1996

By E. J. Magri

For life-of-mine planning, as well as for short- and medium-term planning of grades and mine layouts, it is extremely important to have a clear understanding of the patterns followed by the distribution of gold and uranium within the mining area. This study is an attempt to reconcile the geostatistical approach to the determination of ore-shoot directions, via an analysis of the spatial distribution of gold and uranium values, with the sedimentological approach, which is based on the direct measurement of geological features. For the routine geostatistical estimation of ore reserves, the Hartebeestfontein gold mine was divided into 1I sections. In each of these sections, the ore-shoot directions were calculated for gold and uranium from the anisotropies disclosed by geostatistical variogram analyses. This study presents a comparison of these results with those obtained from direct geological measurements of paleo-current directions. The results suggest that geological and geostatistical studies could be of significant mutual benefit.

Jan 1, 1978

1. New books Australian Institute of International Affairs. Uranium - energy source of the future? Canberra, thelnstitute (Box E181, P.O., Canberra, A.C.T. 2600, Australia), 1979. 202 pp. A$4,95 (postage 50c). Euroeconomics. The steel industry in Western Europe.. industrial and financial indicators. Paris, Eurofinance (9 Avenue Hoche, 75008 Paris, France), 1979. 167 pp. FF4,500 (Available in English and French.) M. B. Piggott. Load-bearing composite materials. Oxford, Pergamon Press, 1979. $15,00. J. H. E. Olaf. Automation and remote monitoring and control in mines. Essen (West Germany), Verlag Gliickauf GmbH, 1979. 200 pp. DM36. (In English.) J. P. Jenkins and E. T. Brown (eds). KWIC index of rock mechanics literature. Oxford, Pergamon, 1979. 742 pp. £60. R. J. Wakeman (ed.). Progress in filtration and separation 1. Amsterdam, Elsevier, 1979. 346 pp. Dfl.llO,OO. 2. New journal As from 1980, Coal Calendar is being published as a separate monthly periodical. 3. Proceedings L. E. St Pierre and G. R. Brown (eds). Future sources of organic raw materials. Oxford, Pergamon, 1979. 612 pp. £22,50. P. Haasen, V. Gerold, and G. Kostorz (eds). Strength of metals and alloys. Oxford, Pergamon, 1979. 3 vols., 1800 pp. $200. K. J. Miller and R. F. Smith (eds). Mechanical behaviour of materials. Oxford, Pergamon, 1979. 3 vols., 1800 pp. U.S.$200. 4. Tax relief? The Publishers' Association of Great Britain recently issued a circular to a number of professional bodies drawing their attention to a court decision in favour of tax allowances on the purchase of textbooks. In January Electroheat The International Union for Electroheat, which com. prises a score of highly industrialized countries, every four years organizes a congress at which experts discuss the technicalities and economics of the latest applications of electroheat in industry and other sectors. Corrigenda: March issue The following amendments should be made to Table II of the paper 'Commodity analysis:

Jan 1, 1980

By J. Zwartendyk, A. Azis

Optimizing the public gains from the exploitation of mineral resources By Dr A. AZIS and Dr J. ZWARTENDYK Every nation must decide how it should exploit its mineral resources so as to contribute most to its national objectives. It is argued that the present value of the future corporate income tax flow derived.from mineral exploitation may serve as a useful indicator in moving toward a taxation policy that would contribute optimally toward the greatest public benefit. The future stream of corporate income taxes depends largely on the mineral endowment, consisting of deposits now being mined, known unmined deposits, and unknown deposits. Unknown deposits may be estimated by geological inference. Both known and unknown deposits can be categorized according to grade and size, and divided into economic and uneconomic deposits on the basis of certain prices, costs, rate of return and taxation levels. Computer simulations can be run of discounted cash flow models at various taxation levels to showthe impact of taxation changes on future tax revenues.

Cutting strong rock with a drag bit assisted by high-pressure water jets By M. HOOD. B.Sc. Hons. (Min. Eng.). B.Sc. (Mech. Eng.). A.M.I.M.M. (Visitor) Experiments are described that led to the discovery that coherent high-pressure water jets directed immediately ahead of drag bits while they are cutting strong rock reduce the magnitudes of the forces on the bits significantly. Tests were carried out to assess the effects of the pressure of the water jets on bit-cutting performance. The pressure was varied between 10 MPa and 50 MPa, the water flow rate being a constant 30 I/min. Over this pressure range, the force on the bit was reduced to the extent that the depth of cut of the bit was at least doubled with the point of impingement of the jets optimized. Forces on the bit were found to be particularly sensitive to the point of impingement of the water jets relative to the bit. The optimum configuration was found to be with two jets, one directed towards each corner of the bit and impinging on the rock approximately 2 mm ahead of the leading edge of the bit. Experiments in which a drag bit and high-pressure water jets were used to cut strong abrasive quartzite in the underground mining situation have demonstrated a potential increase of up to five times in the average depth of cut due to reduction of the forces on the bit. The results from the underground tests indicate that the life of the bit is improved significantly - by a factor of approximately two - when highpressure water jets are used.

Jan 11, 1976

By R L. Bowers, D S. Smit

In light of soaring commodity prices, Nkomati has investigated the potential of processing additional low grade nickel ores to add to their reserves. The Chromititic Peridotite Mineralised Zone (PCMZ) was identified as one ore type with the potential of producing a high grade nickel concentrate. In addition to the nickel, copper, cobalt and PGM?s, the ore also contains a significant amount of chromite which adds substantial value to the project. Pyrrhotite, pentlandite, chalcopyrite and chromite are the dominant minerals within the ore, which on average grades around 0.23% Ni and 12% Cr2O3. The PCMZ ore contains excessive amounts of fibrous silicates which makes it a challenging float, with gangue control as the key element to success. Extensive laboratory testwork, which eventually led to a pilot plant campaign, was undertaken with the aim of developing a process route for treating the PCMZ ore. Several flotation circuit configurations were tested and results from the optimal circuit indicated that a nickel concentrate grading at 8.5% is achievable at a recovery of 78%, with substantial recoveries for the copper, cobalt and PGM co-products. The chromite concentrate, grading at 45%, was extracted from the flotation rougher tailings via a spiral plant. These promising results were incorporated into the plant design and are currently being evaluated in a bankable feasibility study, which will see the current 100ktpm MMZ concentrator being upgraded to a 250ktpm PCMZ concentrator as part of Nkomati?s Phase II expansion.

Jan 1, 2007

By C. C. Oosthuizen

Paper written on project work carried out in partial fulfilment of Technikon Practical Training Frank shaft is mining both Merensky reef and UG2 reef. The Merensky orebody is almost depleted and this was the reason for starting to mine the UG2 ore reserves. It was decided to mine the UG2 orebody with trackless equipment using a bord and pillar mining method. Frank shaft has been mining the UG2 orebody for nearly 5 years. The T-cut mining method was introduced to see if it could improve the grade of the run of mine (ROM) as well the extraction percentage.

Jan 1, 2005

By P. J. Le Roux

"Mining companies are under constant pressure to reduce their cost structures to sustain profitability. In mines using an open stoping mining method, dilution often has a significant effect on profitability. At Target mine in South Africa, dilution in some open stopes was found to exceed 10%, falls of ground being a major contributor to the problem. This dilution can reduce the recovered grade from 5.5 to 4.5 g/t, resulting in a potential loss of about R21 million per month based on a gold price of R240 000 per kilogram. In addition to the cost of dilution, the cost of damage to, or loss of, trackless equipment as a direct result of falls of ground in open stopes is significant. Other associated costs include transport, hoisting, secondary blasting, milling, and plant treatment of waste material. Stable open stopes are essential in order to reduce falls of ground. Back-analyses of stope instability at Target mine have indicated that conventional rock mass failure criteria are unsuitable for stope design. An alternative strain-based criterion has been developed, and has proved to be very successful, allowing the stability of open stopes to be calculated reliably. Since its implementation in 2010, dilution and equipment damage have decreased markedly, creating value for the mine. IntroductionMines that make use of an open stoping mining method aim to extract only the ore, leaving the waste behind. Many orebodies have well-defined boundaries between the ore and the waste rock. In such orebodies, the introduction of waste into the ore due to overbreak dilutes the grade. In massive disseminated orebodies, dilution is less problematic. Overblasting, falls of ground, or other causes may result in dilution. A study undertaken in Canada (Pakalnis et al., 1995) found that approximately 51% of all underground metal mines utilized open stoping mining methods and, from surveys conducted at these mines, open stoping operations experienced dilutions of up to 20%, and occasionally more. Dilution of this magnitude has a significant economic impact on any mining venture. Research carried out in Australia by Capes (2009) came to the same conclusion."

Jan 1, 2017

By J. A. C. Diering

The simulation of mining in faulted ground was recently described by Crouch. His method is extended here to enable a wide range of non-homogeneous mining problems to be modelled. Essentially, the boundary conditions at geological interfaces are incorporated into the overall iterative solution, which is necessary if faults and joints are to be modelled realistically. Two examples are given to demonstrate the method: the mining of coal a seam below a thick dolerite sill, and the mining of a flat reef in close proximity to a vertical fault where hangingwall and footwall rocks have different properties.

Jan 1, 1980

By J. P. Coetzee

There is an ample supply of all the raw materials required for the future development of the industry, with the possible exception of coking coal. Improved methods of coke production are being developed. It is anticipated that steel production will reach eight million tons per annum by 1980. New techniques and equipment for refining steel will be installed, together with new processing equipment. The most serious problem now facing the industry is the acute shortage of labour.

By I. A. Mutemererwa

This paper investigates the role of vertical integration between chrome ore mines and ferrochromium smelters in the location of ferrochromium production capacity in South Africa and Zimbabwe. Vertical integration is important in understanding the increasing competitive position of these two countries as observations show that an increasingly larger share of the global market has been coming from integrated producers. The paper argues that the increased vertical integration between mines and smelters in South Africa and Zimbabwe has led to a lower cost of chrome ore as an input compared with other producers. Underlying this hypothesis is the basic tenet that, more likely than not, production will take place where the costs are lowest. The paper concentrates on high carbon ferrochromium (HCFC) production in market economy countries (MEC). Using an ordinary least squares model, the study tests the relationship between low chrome ore costs and vertical integration shows a statistically significant relationship. These findings partially support the view that the control of sources of chrome ore is a major source of competitiveness. Keywords: competitiveness, ferrochromium (ferrochrome), ordinary least squares, dummy variables, vertical integration, southern Africa.

Jan 1, 2000

By B. van Beek, J. H. Zietsman, A. Lexmond, N. J. Andrew

"In platinum group metals (PGMs) smelting, the slag-to-matte ratios are very high (approximately 4:1 to 9:1). The slag temperature therefore has a strong influence on matte temperature, which is a continual concern due to the low matte melting temperature and its resultant high superheat. Maintaining a stable slag temperature is therefore a critical safety and operational issue. This project aims to improve the understanding of the slag bath temperature drivers so that a more effective slag bath temperature control strategy can be implemented.With the aim of developing a multiphysics model of the furnace, extensive data analysis was performed to develop an in-depth understanding of the process before the start of modelling work. In this work, the effect of fluctuating furnace feed composition on slag temperature was examined. The results are based on equilibrium calculations using FactSage, implemented with ChemApp.A method was developed, using an equilibrium calculation at 25°C, to convert the available chemical assays to approximate mineralogical assays in order to determine the feed enthalpies. Actual 2013 furnace feed data was used and the average specific energy requirement to produce slag and matte at 1600°C was calculated to be 671 kWh/t concentrate. The furnace energy input was then kept constant, and it was found that the slag temperature varies significantly as a function of the feed composition. These results were compared to actual slag temperatures measured on site. It was found that close management of the furnace energy balance is important for maintaining a stable slag temperature."

Jan 1, 2014

By Donald J. Murdock

Column flotation has been developed over the past ten years as an alternative to conventional flotation. It has been used mainly in the cleaning applications of sulphide flotation, where its ability to wash the froth of entrained gangue and produce a higher-grade product has given it a distinct advantage over other technology. The benefits of column flotation can be summarized as follows: Improved concentrate gradeby 2 to 5 per cent . Significantly lower operating costs . Savings in capital investment . Superior control. Since the initial development of the equipment, a number of design improvements have been developed that now form the basis of the Cominco column-cell design. The purpose of this article is to discuss some of those design innovations, and present some typical industrial results.

Jan 1, 1991

By M. W. Hildyard

A blast was engineered close to a tunnel in a deep-level mine with the purpose of studying the wave interaction with the tunnel. Numerical modelling of seismic wave propagation was used in both the forward planning and the back-analysis of this experiment. This paper presents the forward analysis. A likely model for a propagating blast was investigated and developed. This model predicts the influence of the velocity of detonation of the blast and the rise-time of the blast on the radiation pattern, and hence on the expected positions of maximum velocity at the tunnel surface. An attempt was made to quantify the parameters of the blast model, using waveform data from two other blast experiments. The blast model caused particle velocities which were an order of magnitude lower than these measured velocities. Large values for blast pressure were required to match the amplitudes of the recorded velocities. An alternative ?effective? source with a similar mechanism but increased diameter was proposed to account for the higher velocities. It was established that distant velocities scale with the square of the borehole diameter. A calibration blast at the experimental site was also modelled. Agreement in the waveforms was not sufficient for conclusive statements to be made about the validity of the source model. However, the modelled waveforms show an encouraging correspondence with some measured waveforms. This gave confidence that the model could be used to examine wave propagation around the tunnel, and allowed a scaled source to be developed for forward analysis of the main experiment.

Jan 1, 2001

By G. Laing

On scheduled commissioning and effective operation of a solvent extraction circuit relies on getting the design of both the core contact equipment and the peripheral plant right. Experience has shown that poor performance of new plants is frequently a result of ?utility? systems that do not match the requirements of the circuit, rather than the mass transfer equipment itself. Both the operator/owner and designer need to understand the ?complete requirements? for the circuit to get the balance of the design right. This paper reviews generic issues, frequently overlooked or altered during cost-cutting exercises, which have a significant impact on plant performance.

Jan 1, 2002

By M. Sephton

Slat-band chains, currently manufactured from Type 430 ferritic stainless steel, are used as conveyors in various industries. A process to strengthen these chains?with the aim of prolonging the lifetime of the conveyors?was developed recently. The process entails heat treating the cold-worked chain at 475°C,strengthening the material by precipitation of the Cr-rich phase a? at relatively long periods of aging. In the present work, it was found that increasing the interstitial content by solution heat treatments (at 880°C or 930°C) prior to cold rolling and aging, causes an increase in strength at shorter aging times as a result of the precipitation of chromium-rich carbides and nitrides. The solution treatments can introduce martensite into the microstructure if carried out at a sufficiently high temperature. This, along with the deformation caused by cold work, also increases the strength. Corrosion resistance is not affected by the treatments, but ductility is lowered. However, calculated critical crack lengths indicate that solution treatment at a temperature below the Ac1allows for a larger critical flaw size, and that the lifetime of the chains will probably be determined by fatigue. Although the duration of the service of the chains are reportedly controlled by wear, with these treatments the tensile strength of the material is increased to within acceptable limits for conveyor chains. The tensile strength is an indication of the wear or abrasion resistance of a material. It is expected that after the treatments, the wear resistance will be improved, but since embrittlement occurs, the fatigue resistance is lowered. It is concluded that the preferred processing route for the chains would be solution treatment at 880°C, fast quenching to trap the interstitial atoms, cold rolling and then aging at 475°C for 8 minutes.

Jan 1, 1997

By C. J. Tonkin

Compressed air is widely used on South African gold mines. However, due to recent and proposed future electricity tariff increases it is quickly becoming too expensive to produce and use. Boxfront chute systems at ore passes were focused on during this study, and a number of alternative power sources were examined. After comparing primarily costs, and secondarily safety and practicality, of a number of systems based on water and hydraulic oil, a system making use of either air or water was determined to be the most cost effective. A payback time of 8 years was calculated, which will be significantly less taking into account the avoidance of failures due to electricity and water shortages, which would not affect this system due to its ability to swap between either air or water. It was recommended that this system be installed at all boxfront chutes as soon as possible so that the company can begin to benefit from the cost savings.

Jan 1, 2013

By J. Labuschagne

There are a number of factors that contribute to the profitability of a mine and its associated concentrator. Chief among these is the time taken from the first hoist of material from underground to the first batch of concentrate shipped. The main aim of this project was to integrate the mining model with a concentrator production schedule to minimize the time it would take to produce concentrate (without the concentrator having to stop because of a lack of feed material) in the most capital-effective manner. A secondary goal was to ensure detailed stockpiling requirements, as the concentrator is in an area where 'visual pollution' is to be avoided. To achieve these two goals a dynamic stockpile model was created by utilizing the mine production schedule and breaking it down to a daily production figure. Four different concentrator development models were then proposed. The difference between the mine production and concentrator consumption was integrated over the life of the mine to provide the accumulated stockpile tonnages for both Merensky and UG2 ore. To prevent a situation where the concentrator was operational without any feed, the stockpile levels were never allowed to fall below zero. When a development option was selected, the standard metallurgical performance calculations were used to derive a concentrate production schedule, which was used as a basis for commercial negotiations for the sale of concentrate.

Jan 1, 2013