Search Documents

The inherent weakness of the Zincor and similar iron removal processes is the relatively high undissolved zinc loss associated with the iron residue. High soluble zinc losses also occur due to poor filterability of the iron residue even though it may be limited to intermittent events. This work focussed on defining the optimum operating window for the Zincor iron removal process where iron is mainly removed in the form of amorphous, intermediate iron phases such as schwertmannite and ferrihydrite. In terms of the main operating conditions, optimum filterability was achieved under the following conditions: pH of 3.0, temperature as high as practically possible (70C), at least 25 kg/m3 seeding, and a retention time of at least 4 hours. When increasing the temperature from 60C to 70C, the required residence time decreased by almost 50%. Undissolved zinc loss was also reduced from 8% to between 2% and 3% by using a basic zinc sulphate/zinc oxide mixture as neutralising agent to effect iron removal.

Jan 1, 2003

By J. T. M. Amphlett, C. A. Sharrad, M. D. Ogden, R. I. Foster

"A renewed interest in nuclear power around the world in order to reduce greenhouse gas emissions is going to increase demand for uranium as fuel. This will result in more uranium being mined, which will in turn increase associated environmental pressures, such as fresh water use. A move to lower quality waters containing impurities such as chloride would help alleviate these pressures. In this work, we determined the uptake characteristics of weakly basic anion exchange resin Ps-EDA towards uranium from saline solutions in a dynamic flow column. Breakthrough curves were produced, with suppression of uptake being observed for chloride concentrations above 5 g L-1. Calculated resin saturation capacities at zero and 5 g L-1 chloride are comparable with literature values for strong-base anion exchange resins, and exceed those published for weak-base resins up to 20 g L-1 chloride. Data has been fitted to multiple breakthrough models, with the modified dose-response model most effectively predicting uranium recovery. The results show that the ethylenediamine functionality could be suitable for use in future uranium processing flow sheets where a high-saline lixiviant is used. IntroductionIon exchange (IX) is a key technology in the uranium mining industry and is well established for the extraction of uranium from both acidic and alkaline leach liquors (Edwards and Oliver, 2000). It was first employed in 1952 at the West Rand mine in South Africa (Ford, 1993; Taylor, 2016). H2SO4 and Na2CO3 are the most commonly employed lixiviants used to solubilize uranium in acidic and alkaline leach conditions respectively. The chemistry of these systems causes uranium to form anionic sulphate or carbonate complexes, which can be taken advantage of by anion exchange resins.Another major technology for the extraction and purification of uranium from leach liquors is solvent extraction (SX). This technique involves the extraction of uranium from the aqueous phase into an immiscible organic layer. Although this is a commonly used method, there are major drawbacks to it, including the use of large volumes of flammable solvents, solvent loss, phase disengagement, third phase formation, and the production of problematic degradation products (Veliscek-Carolan, 2016). These problems can be circumvented through the use of IX resins."

Dec 1, 2018

By S. C. Greeff

At ISCOR the quantitative determination of the structural properties of coke is done with a Leitz-TAS Image Analysis System. A reflected light microscopic image of a coke sample is converted into a binary image and stored in computer memory or on hard disc. By means of mathematical and stereological techniques the system can transform the images electronically. A lightpen can be used to determine the sequence of these operations. TASIC, which is based on BASIC language, is used as the program language on the computer. The majority of the programs are written by the user to ensure satisfactory results for specific studies. The computer controls the whole system, including the movement of the microscope stage, focusing, transformation and measurement of the image and data processing. The computer is also applied for establishing statistical correlations between the structural and other coke and coal parameters as well as for graphics and predictions of the coke structure. Factors affecting the structural properties of coke are discussed and conclusions are drawn.

Jan 1, 1987

By J. C. Barry, J. H. van Laar, P. L. Crouse, H. Bissett, I. J. van der Walt

"Plasma-assisted spheroidisation of metal powders offers several technical advantages with respect to both the ease of materials handling and powder-metallurgical item manufacturing. Advantages include improved flowability, increased powder packing density, elimination of internal component cavities and fractures, changes in morphology resulting in decreased friction between particles and contamination during pneumatic transport and enhanced particle purity. In this empirical study, spherical iron particles were produced using a microwave plasma operating at atmospheric pressure and characterized using optical microscopy and SEM techniques. Iron powders were fed into the system at fixed operating conditions, resulting in particles with spherical structures. The theoretical estimate of the time required for melting to occur is 1.6 ms, an order of magnitude smaller than the actual residence time. IntroductionParticle design and functionalization has become an increasingly popular aspect of materials synthesis and powder-metallurgical item manufacturing. One such technique involves the spheroidisation and densification of feed materials, typically in the form of chemical powders with wide particle size distributions. The major benefits of powder spheroidisation include improved powder flowability, increased powder packing density and powder purity, reductions in internal voids and defects, as well as the ability to manipulate the particles surface morphologies (Boulos, 2004). Thermal plasma processing has the potential for scale-up and for producing industrial quantities of spheroidised powder.Thermal plasma technologies offer a wide spectrum of material synthesis and treatment options, amongst others the synthesis and spheroidisation of nano-sized ceramic and metal particles (Kumar and Selvarajan, 2006). The spheroidisation process occurs within the plasma discharge via in-flight heating and melting of the powder feed material, given high enough plasma temperatures (Fridman, 2008, p. 495). Surface tension in the molten droplets results in spherical, or nearly, spherical, powder particles being formed upon exiting the plasma discharge where the droplet undergoes rapid cooling and freezes. Quite often, the bulk density of these spherical particles is higher than that of the starting material (Boulos, Fauchais and Pfender, 2013, p. 42). The different plasma spheroidisation techniques reported include radio frequency (RF) induction thermal plasmas (Jiang and Boulos, 2006; Karoly and Szepvolgyi, 2005; Yuming, Junjie and Yanwei, 2013), nontransferred direct current (DC) thermal plasmas (Chaturvedi et al., 2014; Kumar and Selvarajan, 2008; Suresh, Selvarajan and Vijay., 2008) and microwave-assisted plasma processing methods (Chen, Gleiman and Phillips, 2001; Vanamu et al., 2004; Weigle et al., 2004)"

Jan 1, 2016

By Dennis Van Heerden

Southern Africa has a long history of underground hard rock mining dating back to the late 1800?s. The rock support of underground excavations has significantly changed during this period, due to improved technology, experience gained and rock support requirements by mining and geotechnical engineers. This paper examines the available underground rock support methods in Southern Africa with emphasis on the types and characteristics of: - Rock bolt types. - Rock bolt and long anchor grouts. - Thin-sprayed liners. - Sprayed Concrete. - Ground consolidations through injection methods. - Cavity and void filling with aerated cement products. [ ]

Jan 1, 2007

By J. Trckova, P. Prochazka

Physical models from equivalent materials satisfying geometrical and physical similarity have been constructed. A special technology of simulating the excavation of an opening at the front part of a tunnel and of measuring the deformation at the tunnel face was applied. The results yielded by the physical models were used to formulate constitution relations in the numerical solution. This coupled modelling enables us to predict the behaviour of tunnel structures more accurately. On a construit des modèles physiques, réalisés en matériaux équivalents et répondant aux conditions de ressemblance géométrique et physique. Sur ces modèles, on a utilisé une technologie intéressante de simulation du forage du tunnel et de la mesure de déformation du front de taille pendant le forage en progression. Les résultats donnés par les modèles physiques ont été utilisés pour formuler les relations de constitution dans la solution numérique. Une telle construction de modèles combinés permet de prévoir plus précisément le comportement de la structure du tunnel. Es wurden physikalische Simulierungsmodelle aus äquivalenten Werkstoffen konstruiert, welche die Bedingungen der geometrischen und physikalischen Ähnlichkeiten erfüllen. Bei diesen Modellen hat man die interessante Simulationstechnologie des Tunnelvortriebs sowie die Verformungsmessung beim Tunnelabbaustoß während des Vortriebsvorgangs eingesetzt. Die Ergebnisse der physikalischen Simulation wurden zur Formulierung von Konstitutionsrelationen in der numerischen Lösung genützt. So eine kombinierte Simulation erlaubt eine genauere Prognose des Benehmens der Tunnelstruktur.

Jan 1, 2003

By B. P. Watson

Crush pillars have been incorporated into a mechanized, low-profile trackless system at South Deep Gold Mine. These pillars had to be designed to fail near the face and to ensure that pillar failure is contained within the pillar, to avoid bursting and the risk of high loads being generated during a seismic event, respectively. PoweRite backfill bags were recommended to maintain the integrity of the pillars; except in the main access drives, where the sidewalls were to be supported on 5.6 mm diameter weldmesh and yielding anchors. The results of a trial site investigation exceeded expectations, showing a residual pillar strength of about 37 MPa for a newly formed pillar and 8 MPa for a pillar subjected to seismicity and a closure of more than 300 mm. The introduction of these pillars has improved the rock mass conditions because of the active nature of the support, compared to the previous passive backfill method. Importantly, the pillars have increased mining efficiencies and improved face availability. A potential cost saving to the mine of R140.9 million could be realized over a period of 10 years.

Jan 1, 2014

By G. A. Bezuidenhout, J. P. T. Kapusta, D. K. Chibwe

"Peirce-Smith converters (PSCs) are extensively used in the copper, nickel, and platinum group metals industries. The typical converting operation involves lateral purging of air into molten matte through a bank of tuyeres. This blowing operation occurs at low pressure from the blowers, resulting in a bubbling regime that is considered inefficient from both a process and an energy utilization perspective. Inherent drawbacks also include recurrent tuyere blockage, tuyere punching, and low oxygen efficiency.Western Platinum embarked on a full-scale industrial evaluation of generating a jetting regime by using sonic injection. Prior to industrialscale tests, a numerical assessment to ascertain the feasibility of implementing sonic injection into a PSC was conducted. The work included flow characterization at high-pressure injection achieving sonic velocity at the tuyere exit. The 2D and 3D simulations of the three-phase system were carried out using the volume of fluid method together with the RKE turbulence model to account for the multiphase and turbulent nature of the flow.This paper discusses the key findings in understanding plume extension, velocity distribution, shear wall stress analysis, and phase distribution characteristics in the system. Plant trials are also discussed with reference to the commercial aspects of a full-scale implementation of sonic injection in the smelter."

Jan 1, 2015

Prof C T O'Connor holds the degrees of BSc, BSc Hons, University of Cape Town (UCT), where he started his academic Lecturer in the Department of Physical Chemistry in 1976. Mr P Smith, educated in England and the former Southern Rhodesia, joined Gold Fields of South Africa in 1966 as a Metallurgical Learner Official. After obtaining a BSc Eng at the University of the Witwatersrand in 1972, he returned to Gold Fields. Mr P D K Robinson was born in Zimbabwe, and was educated at Dale College in Kingwilliamstown, matriculating in 1952. He holds a Mine Surveyor's Certificate obtained in 1961) and a Mine Manager's Certificate (obtained in 1966), as well as an EDP from the University of the Witwatersrand.

Jan 1, 1991

By R. J. Davidson, W. D. Douglas, J. A. Tumilty

SYNOPSIS Two pilot plants operating on different types of carbon were used to generate steady-state adsorption data in the treatment of gold-plant solutions of high and low tenor. A pilot plant comprising three 4 m long columns and using 3 mm extruded activated carbon was used to treat pregnant solutions with a gold concentration of 5 to 8 g/t at pH 10 to 11,5. Column influent was pumped at a super¬ficial flow velocity of 0,5 m/min while the carbon was moved daily so as to effect gold loadings on the carbon of 5 to 10 k /t. With a carbon-bed depth of 12 m, an adsorption efficiency of 99,9 per cent was obtained in a bed depth of 9 m, which was subsequently reduced to 8 m when the depth of the carbon bed was reduced to 8 m. This improvement in efficiency was attributed to the reduced residence time of the carbon from 12 to 8 days. A corresponding decrease in adsorbed silica indicated that some silica fouling of the carbon had occurred. A second pilot plant, comprising a single column 6 m in length and using coconut-shell carbon of 1,0 to 2,4 mm, treated a solution with a gold concentration of 0,7 g/t at pH 8,0. Feed solution was pumped at a superficial flow velocity of 1,0 m/min while carbon was moved every 8 hours to give gold loadings of more than 5 kg/t. An adsorp¬tion efficiency of 99,5 per cent was indicated at steady state. Intermittent washing of the column with dilute hydrochloric acid was shown to have a beneficial effect on the gold adsorption and to reduce the pressure drop across the column. Intermittent washing with dilute sulphuric acid indicated that there had been some passivation of the car¬bon during the treatment of a solution with a gold concentration of only 0,2 g/t. Compared with other adsorption systems, the countercurrent moving bed appears to offer significant advantages in terms of metallurgical efficiency and capital investment. The inability normally associated with moving-bed systems to treat solutions containing suspended solids may be overcome to a degree by the use of relatively coarse extrud¬ed carbon.

Jan 1, 1985

By H. A. Uys

The metallurgy of tin smelting In a submerged arc furnace By H. A. UYS, Ing. Metallurgy (Pretoria) (Visitor) The control of tin smelting demands a knowledge of slag characteristics and of the equilibrium reaction that governs the process. These factors are explained by reference to the tin-smelting operation at Iscor, Vanderbijlpark. In the primary cycle, it is important to obtain the highest possible FeO content in the slag. In the secondary cycle, a primary slag high in FeO gives a hardhead (iron-tin alloy) high in iron, which is essential if a high ratio of FeO to SnO is to be obtained in the secondary slag. This determines the economy of the smelting operation: the iron that is introduced into the system from the ore concentrate must go out in the secondary slag. Additions of lime are necessary in the secondary cycle but must be limited if the volume of slag is to be kept Iow.

Jan 1, 1977

By K. Liddell

Current practice for the recovery of platinum group metals (PGM) from flotation concentrates is by energy-intensive smelting processes followed by separation and refining of the base and precious metals. Energy costs are rapidly increasing in South Africa and this trend is forecast to continue in future years. Moreover, the smelting operations are highly susceptible to deleterious constituents, particularly chromite; and the increasing tonnages of UG2 chromititic ore being mined results in an increasing chromite content of smelter feeds. Hence there is a substantial incentive to assess and implement alternative processes to smelting for the treatment of PGM concentrates. The Kell process is a patented hydrometallurgical alternative to smelting that is totally insensitive to the chromite content of the feed concentrate and comprises three commercially proven unit operations (pressure oxidation leaching of base metals and sulfur, roasting and chlorination of precious metals). The Kell process provides the opportunity for existing and new PGM producers to significantly reduce their energy consumption, and in particular their consumption of electricity, by removing the need to smelt PGM concentrates. Energy costs, greenhouse gas emissions and installed power requirements are also much reduced. Compared with smelting and refining these reductions are calculated as: ? Total energy consumption-50% reduction ? Electrical energy consumption-84% reduction ? Energy consumption costs-76% reduction ? C02 emissions-70% reduction ? Installed power requirement 92% reduction. The data obtained from simple laboratory batch amenability testing can be readily applied to the Simulus mass and energy balance simulation procedure to determine energy and reagent consumptions, equipment selection and process optimization. The applicability of Kell to treating low-grade 'dirty' concentrates with high UG2 content as well as to polymetallic concentrates containing base metals as the major payable metals with subordinate PGM means that these savings can also be expected when the process is used for treating a range of concentrate types and grades. Keywords PGM,UG2, Merensky, smelting, chromite, electricity, hydrometallurgy, Kell Process, Eskom.

Jan 1, 2011

By M. W. Hildyard, J. A. L. Napier

The improved design of support systems and stoping strategies when changes in depth, stratigraphy, or mine layouts are considered must rely on the designer's fundamental understanding of the deformation mechanisms adjacent to underground openings so that he can extrapolate and predict expected mining conditions. This paper presents a numerical approach to the modeling of the growth and interaction of mining-induced fractures near the edges of deep tabular excavations in brittle rock. Fractures are represented by displacement-discontinuity elements that are allowed to propagate according to prescribed growth rules. This procedure is justified by the reproduction of several features observed in laboratory simulations of fracturing around openings in blocks of rock subjected to uniaxial and biaxial compression. An attempt is then made to explain some of the attributes of the fracture zone surrounding tabular stopes. Particular questions of interest are the sequence in which fractures form and are mobilized in front of the mining face, the effect of parting planes parallel to the plane of the excavation, and the distribution of stress parallel to the hangingwall and footwall.

Jan 1, 1992

By A. M. Hearn, J. G. Roos

Energy consumption, being a large proportion of the input of the ferroalloy production process, can be measured in terms of the efficiency with which the energy is utilized and the effectiveness with which it is used. The efficiency of the usage of energy revolves around the specific consumption of the energy for the production of the alloy, which encompasses the thermodynamic aspects of the process and is more of a metallurgical function that will not be addressed further in this paper. The effectiveness with which the energy is utilized is determined by the optimisation of the electricity supply from the utility (in this case Eskom). The South African electricity supply industry is on the brink of considerable restructuring, implying changes in ownership, structure and regulation. In other countries, however, restructuring has often seen higher prices. Owing to the diversity of growth prospects in South African markets, Eskom is turning to new market management and generation strategies. In future, Eskom will develop pricing strategies to increase demand from attractive customer segments such as paper & pulp, iron & steel, aluminium, and other metallurgical industries. There will be a broader spectrum of product offerings, including dynamic pricing options and demand-side management incentives. In a future electricity market that will become more dynamic and demanding, it will become increasingly important for electricity consumers to optimise their electricity supply. There are many facets in optimising the electricity supply, which include optimal utilisation of the tariff, integrating energy cost management into the production planning process, implementation of demand-side management actions, modelling, scenario planning (.what-ifs?.), optimisation, maintenance scheduling coordinated with the tariff periods, etc. This paper gives consideration to the status of the development of technology at the manganese alloy works of Samancor at Meyerton, South Africa in order to increase the effectiveness with which energy is utilized.

Jan 1, 2004

By M. Tangstad, D. Lu, G. Tranell, S. Gaal, J. Safarian

The kinetics of MnO reduction from high carbon ferromanganese slag was investigated using a sessile drop technique at 1600 ºC. The effects of reductant type, ambient atmosphere and slag composition on the MnO reduction were illuminated. Two different types of industrial reductants (ground to a particle size of 44 to 106micron and pressed to pellets) were used as substrates for small slag droplets of varying composition, which were reacted in a CO or Ar atmosphere with the reaction studied in-situ. The cross sections of the reacted slag-carbon samples were subsequently studied by EPMA to find the extent of MnO reduction as a function of reaction time. It was found that the rate of MnO reduction is affected by both the type of reductant, the ambient atmosphere and the presence of metallic components in the slag. Higher reduction rates were obtained for charcoal than for coke as reductant while a CO atmosphere unexpectedly yielded faster MnO reduction than an Ar atmosphere. It was also found that metal prills in the initial slag will increase the rate ofMnO reduction.

Jan 1, 2007

By W. Spencer

An examination is made of quality standards in castings produced by the South African foundry industry, and some examples are given of the consequences of poor quality to the user. Corrective measures are suggested.

Jan 1, 1981

By D. Noort, M. Dawborn, D. O. del Castillo

This paper was originally presented at the North American/9th US Ventilation Symposium, June 2002, Kingston, Ontario, Canada. Reprinted with permission of the publishers, A.A. Balkema Publishers, Rotterdam, Netherlands. This paper is a study of the ventilation, cooling and refrigeration system design of the Mindola copper mine in Zambia. The challenges that were addressed varied from the restrictions imposed by an ageing infrastructure to the requirement for increasing the annual production rate, coupled to the introduction of a higher level of mechanization while maintaining acceptable conditions and limiting total ownership costs. A description of how the ventilation, refrigeration and cooling systems were modelled in order to obtain the projected heat loads associated with two different mining methods over the life of the project. The methodology included a number of iterations to optimise the design and include aspects such as the expected inrush of hot fissure water, the operation of diesel machinery at depths in excess of 1500m below surface, developing a cost-efficient cooling strategy and selection of the refrigeration machinery to meet the requirements imposed by the cooling strategy. This paper demonstrates the successful implementation of an integrated design approach.

Jan 1, 2005

By P. Bracher

Most efforts to mechanize low seam (narrow reef) mining of platinum ore are presently based on board-and-pillar methods with1.6?1.8 m in reef excavation. This paper attempts to substantiate the benefits of low profile mining: primarily improved head grade with resulting reduced tailings losses. Board-and-pillar equipment supplied by DBT, facilitating1.1?1.2m mining height has been in operation in an Anglo Platinum mine since September 2001. Major aspects of the equipment, battery scoops (LHDs) and rotary bolting rigs, are described and presently achieved results reported. The medium term industry goal is rock breaking without the use of explosives. An outline of present DBT developments is presented.

Jan 1, 2003

By W. J. Kempson

As a result of the rising electrical energy costs in South Africa, a method was sought to reduce the overall electrical consumption of typical shaft systems. A typical shaft configuration was analysed and the primary energy consumers were identified. The ventilation fans for this system were found to consume 15% of the total energy of the shaft system. It was calculated that more than 50% of this energy is consumed by the shaft itself, more specifically, by the pressure losses that occur in the shaft as the ventilation air passes through it. In order to ensure that the theory being used for the evaluation of these shaft systems is accurate, a total of five shafts were instrumented and the actual pressure losses over the shafts plotted against time. These shafts were then analysed from a theoretical perspective. Finally, in order to ensure a thorough understanding of the behaviour of the ventilation air in shaft systems, the systems were simulated using computational fluid dynamics (CFD) techniques. There were significant discrepancies between the theoretical analysis and the CFD simulation during the initial comparisons. This discrepancy lessened as the complexity of the CFD models increased, until when the complete shaft was modelled using the full bunton sets, the pipes, and the flanges, the difference between the theoretical evaluation and the CFD simulation was small. This result demonstrates that the theory is insufficient and that the interrelated effect of the buntons and fittings has not been fully appreciated by current theory. The final phase of the work presented here was to evaluate the costeffectiveness of using different bunton shapes and shaft configurations. It is shown that the increase in the pressure losses and therefore the direct operating costs of the shaft can vary by as much as 80%, depending on the bunton configuration chosen. The placement of the piping in the shaft can increase the pressure losses, and therefore the direct operating costs of the shaft, by as much as 12%, depending on the placement of the piping in the shaft; this effect includes the use of flanges. The use of fairings on a large cage can reduce the resistance that the cage offers to the ventilation flow by as much as 30%. This, however, does not translate into a direct saving because as the cage moves through the shaft, the overall effect is transitory. These savings can be significant when the items highlighted in this work are applied correctly. Keywords shaft design, ventilation, energy consumption, modelling, CFD.

Dec 1, 2013

Contribution by W.D. Ortlepp In the Journal of May 1994, the authors first presented the concept and analysis that formed the basis for a design approach for deep tunnels, now expressed more explicitly in the present paper (March/April 1996). In a contribution in the Journal of March/April 1995, I expressed a certain disquiet about the validity of their original approach. The authors responded to these criticisms in the same issue. It is apparent to me now that both the contribution and its rebuttals were written, probably for different reasons, in such an obscure and pedantic way as to further confuse the reader rather than provide enlightenment. My concern still persists. But in order to avoid further confusion I will attempt to pose my uncertainties and difficulties in a much more direct way. On page 98 (top of 2nd column) in the earlier paper, an important statement concluded as follows: '. . . the horizontal ellipse requires 140 per cent less force for equivalent stability'.

Jan 1, 1996