Search Documents

By D. C. Andersen, G. L. Smith, J. Pearson-Taylor

Following a restructuring of Anglo Platinum Limited in 2004 the strategic long-term planning function has been centralized. This paper describes the revised strategic long-term planning process covering aspects of the planning cycle, systems and methodologies, categorization of capital expenditure, corporate governance and planning tools.

Jan 1, 2006

By B. X. Huang

Hydraulic fracturing technology is presented as a solution to improve permeability and thus solve the extraction problem of coal seam gas in low-permeability gas-bearing coal seams. Given an existing group of original cracks, the propagation of main hydraulic cracks and hydraulic wing cracks was simulated using realistic failure process analysis software. The process represents the structural transformation of hydraulic fracturing and permeability improvements caused by it. In addition, a field test for improving the permeability of gassy coal seams by hydraulic fracturing was also conducted. The propagation of the main cracks and wing cracks by hydraulic fracturing forms a network of original joint cracks, hydraulic wing cracks, and main hydraulic cracks, which improve the permeability of the coal seam. High-pressure water in the drill hole and in the main hydraulic cracks permeates the two flanks of the hole, forming the permeating water pressure. With an increase in drill water pressure and an extension of the main hydraulic cracks, the permeating water pressure on both sides of the main hydraulic cracks in the coal mass also increases. Hydraulic cracks tend to form connections through rock bridges. The extension of hydraulic wing cracks through connections in the rock bridges between the cracks transforms the rock mass to a fractured structure and improves its permeability. Hydraulic fracturing technology for improving permeability in underground conditions can increase the amount of gas drainage by a factor of 15. A stress relief area develops at a radial distance of 10-2.0 m from the hydraulic fracturing drill hole, while an area of rising stresses, called the pressurized area, develops a further 15 m away from the pressurized hole. Practice has proved the existence of the stress transfer phenomenon and the high stress area after fracturing. This kind of hydraulic fracturing technology is more effective in holes drilled from underground than in surface drill holes, with respect to costs and controllability, and is therefore the major trend in gas drainage development in coal mines.

Jan 1, 2012

NOTICE The Institute has received requests for copies of Uranium in South Africa', Vols. 1 and 2, but is unable to supply, as all copies have been sold out. If any members have copies they wish to dispose of it would be appreciated if they would contact the Secretary, P.O. Box 1183, Johannesburg. Telephone 834-1271.

By T. Flitton, R. Peattie

"The extreme depths and consequent expense of drilling and sampling the gold-bearing reefs of the Witwatersrand Basin have resulted in limited data being available for estimation of grade ahead of the mining face. There is, however, a wealth of information from mined-out areas of these deposits. This estimation challenge resulted in the development of a unique method of Mineral Resource estimation.AngloGold Ashanti (AGA) utilizes a technique termed macro cokriging (MCK), which allows for the integration of the limited advanced borehole data with the large chip sample data-sets from the previously mined-out areas by adopting a Bayesian geostatistical approach. The MCK process, in short, is the estimation of mixed support size data together with the application of four-parameter distribution models.The gold value estimation for the Carbon Leader Reef (CLR) on the AGA TauTona Mine is used in this paper as a case study of the process and to demonstrate the effectiveness of this technique through production reconciliation. The current method has been proven over the last 20 years and is now an established part of the Mineral Resource evaluation process within AGA.IntroductionOwing to the extreme depths of the goldbearing reefs at the AngloGold Ashanti (AGA) Witwatersrand operations and the prohibitive expense and time involved in drilling boreholes to the required depth, only limited drilling and sampling data is available ahead of the mining face. Whereas traditional estimation techniques are interpolative, within the Witwatersrand the estimation is primarily extrapolative, with the majority of the data being sourced from the mined-out areas. This significant challenge to estimation resulted in the development of a unique method of Mineral Resource estimation and evaluation."

Jan 1, 2016

By T. Y. Yunsel

Estimation techniques such as polygonal, triangular prism, trapezoid, isopach maps, and inverse distance methods are often used in ore or industrial minerals deposit evaluation. These techniques do not express the variability of the deposit and do not allow a determination of the reliability of the estimates. However, geostatistical methods can express a measure of the error associated with the estimates, by finding weighting coefficients for a given mining block, and can also help with data configuration that minimizes the error. This work addresses an application study on the quality and reserve characteristics of the cement raw materials of the Adana Cement Factory in Adana, Turkey, based on the spatial distribution and variability of the chemical components (Si02, CaO, A1203, Fe203). The study has been carried out using a geostatistical procedure that is useful for site assessment, characterization, and monitoring situations where data are collected spatially. Directional and omnidirectional experimental variograms of the cement raw material variables showed that neither strong geometric nor severe zonal anisotropy exists in the data. The most evident spatial dependence structure expressing the continuity for omnidirectional experimental variograms were characterized by exponential and spherical variogram models. These models have been used in cross¬-validation analysis, which proved that these models, their parameters, and kriging parameters are applicable for the study area. Quality contour maps of the deposits at given levels underground were estimated using a kriging interpolation technique. Anomalies such as bullseyes and drift were not observed in the maps that were generated. Kriged maps showed the spatial distribution of quality continuity and variability of the deposits. Grade-tonnage curves and total tonnage estimates in the particular grade were determined using ordinary kriging in order to improve the mining operation and planning. Consequently, local uncertainty and the probability of extreme values occurring are tools of prime importance for the mine planning, the optimum mix of raw materials coming from different quarry stopes.

Jan 1, 2012

By S. Luyckx

This paper reports hardness and abrasive wear resistance test results from a wide range of WC-Co alloys, varying in cobalt content as well as WC grain size. The results show that the abrasive wear resistance increases with increasing hardness and that the rate of increase is higher for larger WC grain sizes. The increase in abrasive wear resistance was found to be parabolic up to a critical hardness value and exponential above that value. The transition from parabolic to exponential behaviour was found to occur at the same contiguity value for all grain sizes, which suggests that at that contiguity value the WC skeleton becomes continuous in all WC-Co alloys.

Jan 1, 2004

By J. Härkki, R. Hiltunen

The Akanvaara intrusion (surface area 50-55 km2) in Savukoski, Northern Finland, hosts 23 distinct monocumulate layers of small euhedral chromite crystals enclosed in a silicate matrix. These chromitite layers have been divided into four groups; UC (upper chromitite), ULC (uppermost lower chromitite) LC (lower chromitite) and LLC (lowermost lower chromitite). The driving force for investigating the Akanvaara chromites and their reduction behaviour originated from their very low MgO content and relatively low Al2O3 content, giving them a unique quality which based on thermodynamics should facilitate the reduction. Another interesting feature is the high amount of V2O3 present especially in the upper chromitite. The chromites included in this study are from the UC and ULC layers (24.9 and 22.7 per cent Cr2O3 respectively). To obtain a better understanding of the reduction behaviour of Akanvaara samples in comparison to MgO-bearing chromitites, Kemi chromite from the ferrochrome works in Tornio, Finland, was included in the study as a reference sample. The reduction experiments were isothermal in a temperature range of 1000-1400°C in CO atmosphere. Experiments were also conducted with coke addition in pellets and briquettes in CO/Ar/H2 atmospheres. The results of the reduction experiments complemented with microanalytical research indicate that the Akanvaara chromites do reduce to a higher degree than the Kemi chromite. Although the aim was to characterize the mechanisms of reduction focusing on gas-solid reactions, the nature and amount of the gangue minerals was such that a considerable amount of slag phase was formed, which affected the reduction mechanisms extensively. The structural features together with low MgO and high FeO content in both Akanvaara chromites are important factors resulting in better reducibility than in the Kemi chromite.

Jan 1, 2004

By P. C. van Aswegen

Owing to the strategic value of organic solvents, an investigation was conducted on the reduction of solvent losses at the Buffelsfontein solvent-extraction plant. It was established that the major cause of the high solvent losses was the high content of suspended solids in the uranium pregnant solution. To improve the clarification of the pregnant solution, it was decided to replace the conventional sand clarifiers that were being used at that stage. After pilot-plant tests had been conducted, a circulatorclarifier 16 m in diameter was installed to treat 9000 m3 per day of pregnant solution containing approximately 500p.p.m. of suspended solids. The clarifier was commissioned successfully, and yielded an overflow containing approximately 80 p.p.m. of suspended solids compared to the previous value of 250 p.p.m. This reduction in suspended solids immediately resulted in a decreasing trend In losses of organic solvent, finally yielding a reduction in these losses of approximately 50 per cent.

Jan 1, 1983

By T. Chikande

"Falls of ground pose costly hazards to personnel and equipment and thus measures should be taken to prevent them. This study endeavours to improve the support systems used in geotechnically poor ground at a Zimbabwean platinum mine by analysing the status quo and recommending an effective support system. Various techniques were used to determine the quality of ground conditions, predict the rock mass behaviour, and to identify the appropriate rockbolt type. An analysis of the current ground control methods and their limitations was also undertaken.The results showed that the current support system and mining practices in poor ground need to be modified to improve safety and productivity. Stoping overbreak is influenced by poor ground conditions and the explosives currently used. The use of emulsion is recommended to replace ANFO. Redesigning of pillars is also recommended in poor ground conditions. An evaluation of the current roofbolt system indicated an opportunity for improvement. With new insight on the performance of the shorter length roofbolts currently in use, a new support system was recommended taking into consideration cost-benefit analysis. Barring down using pinch bars in poor ground was seen as a risky and time-consuming exercise, hence the use of mechanical scalers is recommended to achieve zero harm and to meet production targets. Smoothwall blasting is recommended in poor ground to minimize excavation damage. Other recommendations include the use of hydrological surveys to determine groundwater levels and implement corrective measures. Both empirical and numerical modelling approaches need to be utilized in determining the optimum support. IntroductionThe presence of geological discontinuities such as faults and joints weakens the rock mass. Adequate support is critical in achieving zero harm in underground mines. This paper reviews the current support systems used in poor ground conditions at a Zimbabwean platinum mine. The area of research is located on the Great Dyke of Zimbabwe. The mine exploits platinum group elements (PGEs) and base metals. It is shallow, having a maximum depth of less than 300 m. The Great Dyke is the second largest reserve of PGEs, following the South African Bushveld Complex (Oberthur et al., 2012). It is a linear layered intrusion that extends for about 550 km with a maximum width of 11 km (Prendergast, 1989). The generalized section of the Great Dyke is almost like a trumpet, comprising layers that dip towards the centre. The reef exploited at the mine, the Mineralised Sulphide Zone (MSZ), is located in the pyroxenite layer, which is hosted in the ultramafic sequence. The MSZ is a uniform layer about 2– 3.5 m thick, dipping at around 10–14° from surface outcrop towards the axis of the basin, and located between bronzite and websterite horizons. The visible disseminated sulphide mineralization shows a typical and consistent vertical distribution of platinum group metal (PGM) and base metal values. The research was undertaken to review the current support systems used in geotechnically poor ground conditions in a bid to improve both safety and productivity."

Jan 1, 2016

By I. Zemanek, A. Rozsypal

Mrazovka tunnel was excavated under one building whose subsurface space was not possible to reinforce against additional settlements induced by digging. In the presented contribution the risk analysis, warning levels and results of deformation measurements are described. Lespace souterrain d‘un des bâtiments sous lequel le tunnel Mrazovka a été creusé n‘a pu être renforcée contre l‘affaissement supplémentaire provoqué par l‘emplacement du tunnel. Le matériel présenté décrit l‘analyse des risques, le niveau des limites et les résultats des mesures des déformations. Der Untergrund eines der Gebäude, unter dem der Tunnel "Mrazovka" ausgeschachtet wurde, war es nicht möglich, gegen nachträgliches Setzen zu versteifen, hervorgerufen durch die Untertunnelung. Im vorliegenden Beitrag sind Gefahrenanalyse, Grenzwerte und Ergebnisse von Deformationsmessungen beschrieben.

Jan 1, 2003

The 106th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22 Erlswold Way, Saxonwold, Johannesburg on Wednesday, 13th August, 2003. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Kevin Moxham, President, Association of Mine Resident Engineers Prof. Jay Barton, Vice President, The Geological Society of South Africa Dr Gus Muller, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Marius van Rooyen, President, Institute of Mine Surveyors of South Africa Benjamin Ngulube, Deputy Vice President, South African Institution of Electrical Engineers Dr Francois Malan, Chairman, South African Institute of Rock Engineering Dr Paul Jourdan, President, Mintek

Jan 1, 2003

By A. A. Smithen

There is an increasing awareness of the importance of including an assessment of environmental liabilities in the preparation of bankable feasibility documents. This means that environmental assessments of proposed, existing and decommissioned mine sites have to be undertaken for the purposes of quantifying environmental liabilities and assessing potential risks. This paper examines the need for considering environmental liabilities before describing the approach adopted in undertaking due diligence studies for the preparation of bankable feasibility documents and some of the difficulties experienced. Finally, some concluding remarks are made and the implications for the mining industry are discussed.

Jan 1, 1999

By John Freer

Over 200 delegates attended the SAIMM Colloquium on Flotation, which was held at Mintek on 22nd September, 1983. In introducing the programme, the Chairman of the Technical Programme Committee, Mr Eugene Fivaz, said that an attempt had been made to strike a balance between theoretical and practical papers, which he hoped would provide something for everyone. He wished to record in advance the thanks of the Institute to S.A. Cyanamid for sponsoring the lunch, and to Bateman Equipment Limited for the cocktail party to be held at the end of the day's proceedings.

Jan 1, 1983

Council and Standing Committees - 1982/83 President: Prof. A. N. Brown Vice Presidents: Prof. R. P. King and J. D. Austin Honorary Treasurer: Prof. D. G. Krige Immediate Past President: G. Y. Nisbet Members of Council: B. C. Alberts, R. H. English, P. T. Fewell, C. E. Fivaz, J. S. Freer, Prof. G. G. Garrett, J. J. Geldenhuys, Dr A. K. Haines, P. N. Harris, H. E. James, Dr B. K. Loveday, Dr J. Lurie, D. G. Malan, G. Pienaar, B. E. Protheroe, Dr 0. K. H. Steffen, G. C. Thompson, Dr H. Wagner, Dr P. T. Wedepohl. Chairman, Witbank/Middelburg Branch: H. C. van Zyl.

Jan 1, 1983

A number of impending and actual pit wall failures have been observed and documented, which have been interpreted to initiate on newly generated structural features. This infers failure through intact rock. Failure mechanisms have been postulated resulting from circumferential stress, extensional strain and brittle flexure. These will be discussed in the context of the failures and the associated monitoring. The implications of failure initiating on ?unknown? features has a significant impact for deep open pit mines where designs are based on the expected structural regime. Being able to anticipate such failures is important for design. Equally important is management of such changes as they arise. In this context, monitoring using high resolution microseismic techniques will be discussed as a means of providing early warning of such failures.

Jan 1, 2006

By W. J. Whiten

Models of cone crushers and vibrating screens are described. These models have been constructed from actual plant data using a systematic model-building technique. Included in this technique is regression analysis using multi-dimensional spline functions. The models have been used too simulate complete crushing plants and hence to design and evaluate a control system for crushing plants.

Comminution is a vital part of minerals extraction, and therefore of the South African economy. The high cost and throughput-limiting nature of comminution forms a strong motivation for research directed at improving the efficiency of the process. Building on a ten year background of fundamental charge motion research, a new formal UCT flotation and communication group has been formed. The group is also moving strongly into the field of milling circuit modelling and simulation, based on close links formed with the Julius Kruttschnitt Mineral Research Centre (JKMRC) of Australia, and an international collaborative research programme.

Jan 1, 1998

By C. Ringas, F. P. A. Robinson

Various theories proposed to account for microbial corrosion are reviewed as a background to a better understanding of this type of corrosion in iron-based alloys. Experimental evidence is presented to show that even stainless-steel alloys are prone to microbial attack by sulphate-reducing bacteria. The corrosive attack by the bacteria is due primarily to the hydrogen sulphide that is produced as part of their metabolic processes.

Jan 1, 1987

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery ? Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery ? Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2012

By M. Rhodes

The Sukari project, which is owned by Centamin Egypt Ltd, is located in southern Egypt, 770 km south of Cairo but close to the Red Sea. The project is the first new gold development in Egypt and was commissioned in the middle of 2009. In 2007, Centamin purchased the CIL plant from the Kori Kollo mine in Bolivia. This plant was originally designed to treat 6.5 Mtpa of oxide ore. The Sukari deposit contains an oxide zone close to surface with a thick zone of mixed oxide and sulphides below this. The sulphides contain relatively coarse pyrite and arsenopyrite with fine <10 µm gold inclusions. Eventually, the sulphide ore will be mined from underground. Metplant Engineering Pty Ltd, a subsidiary of Bateman Engineering Pty Ltd was contracted to design modifications and additions to the Kori Kollo plant to enable it to treat the Sukari ores. The plant was designed to treat the three ore types in stages. Throughput was set to 4 Mtpa, dueto Sukari ore being harder, at a head grade of 1.7 g/t to produce 200 000 oz of gold. The oxide circuit was based on the use of the Kori Kollo plant and the difference with mixed ore was that the oxide circuit would treat flotation tailings rather than ore. This circuit has a leach capacity of 26 000 m3 and residence time of 24 hrs The main feature of the upgraded mixed ore plant was the addition of a flotation circuit to produce a concentrate which would be reground and treated in a separate leach and elution circuit. Ore is crushed in a gyratory crusher and the comminution circuit uses a conventional SABC producing a product with a P80 of 150 microns. The throughput of 580 tph of oxide ore and 500tph of mixed ore was set to match the mills from Kori Kollo, with the addition of the pebble crusher to accommodate the more competent Sukari ore. The flotation circuit comprises a single rougher circuit to maximize recovery. The concentrate is thickened prior to regrinding which is carried out in a tower mill and two SMD mills operating in series. The final product, with a P80 of 12 microns, from the regrind circuit is leached in a CIL circuit with a total capacity of 2 550 m3. Gold is recovered through a conventional pressure Zadra circuit. Tailings from both circuits report to separate tailings thickeners and are pumped to a tailings storage facility. The circuit is designed to maximize the recovery of water. The project lies in one of the driest deserts in the world and a feature of the operation is the use of sea water from the Red Sea. This water is pumped 25 km from the coast.

Jan 1, 2009