Search Documents

By P. A. Olubambi

The leaching of zinc and copper from Nigerian bulk sulphide ore with sulphuric acid in the presence of hydrogen peroxide was studied. The aim of the study was to investigate the effectiveness of hydrogen peroxide as an oxidant for the sulphuric acid leaching of zinc and copper from a complex sulphide ore. Distribution of elementals within the various particle sizes was initially determined by ICP-OES and XRF to provide a basis for explaining the dissolution process. The effects of concentration of hydrogen peroxide, particle size, stirring speed, and leaching time at a constant temperature of 298K were studied. There were variations in elemental and mineralogical composition within the different sizes. The concentrations of zinc and copper reduced as particle size decreased while silica, sulphur, iron and lead contents increased. Dissolution results showed that the leaching rate of copper was lower than that of zinc. The highest recoveries of zinc and copper were obtained at a leaching time of 180 minutes, stirring speed of160 rpm, particle size of 75 µm and a concentration of 1M H2SO4/1MH2O2. It was observed that the leaching rate of zinc and copper increased with increasing hydrogen peroxide concentration. Increased stirring speed had a negative leaching effect as it promotes hydrogen peroxide decomposition. Keywords: Nigerian sulphide ore, zinc, copper, hydrometallurgy, sulphuric acid, hydrogen peroxide.

Jan 1, 2006

By R. J. Hundermark, L. R. Nelson

"The critical importance of tap-hole design and management for furnace performance and longevity is explored through examining some of the specific matte, metal, and slag tapping requirements of non-ferrous copper blister and matte converting and smelting, ferroalloy smelting, and ironmaking systems. Process conditions and productivity requirements and their influence on tapping are reviewed for these different pyrometallurgical systems. Some critical aspects of the evolution of tap-hole design to meet the diverging process and tapping duties are examined. Differences and similarities in tapping practices and tap-hole management are reviewed. Finally, core aspects of tap-hole equipment and maintenance are identified – aspects that are considered important for securing improved tap-hole performance and life, so pivotal to superior furnace smelting performance. IntroductionThe sheer diversity of tapping configurations used on industrial pyrometallurgical operations is at first bewildering. They range from historical tilting furnaces without tapholes to modern eccentric bottom tapping (EBT) tilting and/or bottom slide-gate electric arc furnaces; to classical single tap-hole multiphase tapping (e.g. metal/matte and slag); to dedicated phase tap-holes (e.g. dedicated metal/matte-only and slag-only); to dedicated phase multiple tap-hole configurations (up to eight metal/matte-only tap-holes and six slag-only tap-holes); to more esoteric metal/matte-only siphons and slag overflow skimming, e.g. Mitsubishi Continuous Process (Matsutani, n.d.). This can be further complicated by periodic batch tapping; consecutive tapping on a given taphole; alternating tap-hole tapping practice; near-continuous slag-only tapping, with discrete batch matte/metal tapping on higher productivity, but low metal/matte fall (<20% by mass feed) Co and Ni ferroalloy and platinum group metal (PGM) matte furnaces; near-continuous tapping through batch tapping of individual tap-holes that are opened consecutively (Tanzil et al., 2001; Post et al., 2003); to fully continuous tapping on coupled multi-furnace cascades (Matsutani, n.d.)."

Jan 1, 2016

By W. K. Brisden

The SAG Milling Seminar, which was held at Murdoch University in Perth on 30th November and 1st December, 1989, was a very successful technical seminar. Organizer Dr Norm Stockton reported a total attendance of 130, which was higher than the 70 expected: 20 delegates came from the eastern States and the remainder were from Western Australia.

Jan 1, 1990

Papers of Interest The following papers may be of interest to members. APCOM The Thirteenth International Symposium on the Application of Operation Research and Computer Techniques for Decision Making in the Mineral Industries will be held at the Technical University CIausthaI, Federal Republic of Germany, from 6th to 11th October, 1975.

Jan 1, 1975

By C. S. Chenga

Sustainable development is currently an extremely relevant concept worldwide, especially in developing countries like South Africa. Mining and metals companies are also directly affected by the sustainable development agenda. The Mining Charter?s requirements as well as new legislation (Mineral and Petroleum Resources Development Act) expect, among others, for mines to support infrastructure and poverty eradication projects in the communities surrounding the mines. The aim of this paper is to, against the background of a qualitative study of mining communities in the North-West Province of South Africa, put forward some critical factors for the sustainability of social development projects in the mining sector.

Jan 1, 2006

By W. C. Joughin

A risk evaluation model has been developed, that enables the quantification of expected injuries and economic losses resulting from rockfalls associated with a support system in a given geotechnical environment. This enables the comparison of different support systems based on the expected frequency of injuries and the total cost of the support system, including the expected economic losses. The model takes into consideration the variability in joint orientations and joint strength within the geotechnical environment and the variability and quality of support systems. The quantification of the benefits of other rockfall risk-mitigating strategies, such as the effectiveness of barring or monitoring, are also incorporated in the model. The risk model is described in this paper and the validation of the model and case studies are described in Part II.

Jan 1, 2012

By R. C. O’Ferrall, W. G. Goulding

This paper describes the performance of a Robbins 52R Boxhole Borer from its introduction into the mine in July 1975 until late in 1977. As indicated by the costs involved, the performance has increased considerably and is expected to be even better once further envisaged modifications have been made. The average cost for the first half of 1977 was R275 per metre bored as against an average of R628 for 1975.

Jan 1, 1978

The 98th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 16th August, 1995. Obituaries The President announced the death, during the year, of the following members: Honorary Life Fellows R.C.J. Goode, F.G. Hill Life Fellows R.S. Cooke, J. W. V. Mortleman Fellows S. Craib, R.R. Hendry, T.J.B. Jones

Jan 1, 1995

By D. R. Lawrence

A method for the calculation of the economic optimum spacing of raise connections in &apos;scattered&apos; mining layouts is described. The method of calculation and the results obtained in a case study are presented. An indication of how the overall optimum spacing (which satisfies both economic and geological considerations) can be determined is also given. " The case study demonstrates that, even with the present strike-cleaning systems,significant savings in working costs can result from an increase in the spacing between raise connections. Furthermore, improvement of the present systems would result in a considerable increase in these savings.

Jan 1, 1983

By C. H. Wyndham, N. B. Strydom, S. Benade

A group of 23 underweight men weighing less than 50 kg were subjected to an acclimatization procedure in which the work rate was gradually increased from 35Watts on the first day to 70Watts on the eighth day. Excessively high body temperatures and heart rates were observed on these subjects throughout the acclimatization period and on their performance they must be rated as heat-intolerant. It can be concluded that such underweight men should not be subjected to acclimatization at such high work rates and that they should not be allocated to tasks involving these rates in a hot environment. The fact that their body surface areas are inadequate to enable them to get rid of the internal heat produced during strenuous work plus their low work capacities are the major reasons for their inability to tolerate heat.

By M. Mikolás, L. Pomothy, K. Špakovská, M. Vanek

"Enterprises are faced with increasing economic competition and managers are obliged to look for methods that will ensure a competitive edge in their companies’ markets. These methods include managerial concepts that employ common sense and are low cost. One of these approaches is the KAIZEN methodology, of Japanese origin; kaizen means continuous improvement (CI) when translated. A mining company, despite some of its idiosyncrasies, is just an enterprise where the application of KAIZEN can be advantageous. The company investigated, OKD, is the only domestic producer of hard coal in the Czech Republic and operates four mines that produce 11 Mt of coal annually. The OKD management team opted for KAIZEN as their principal method of continuous quality improvement. This paper suggests ideas for development and application of processes that provide for continuing improvement of production and management. The authors have taken the OKD Company to be their benchmark in the field of mining activities. The paper also focuses on possible difficulties accompanying the introduction of CI sustainable methods. Three years of application of CI methods has increased the income of the company by almost US$38.1 million, which provides a strong argument for continued application."

Jan 1, 2015

By Huang Zhiwei, Paul Skayman, Kevin Holley

In 1989 The First Brigade for Geology and Mineral Exploration of Qinghai Province discovered gold at Jinlonggou and Qinlongtan, Tanjianshan. Between 1992 and 2002 small scale mining was carried out at these sites using underground mining methods at Jinlonggou and an open pit at Qinlongtan. During 2003 and 2004 geotechnical investigations were carried out in support of a bankable feasibility study. An important objective of this investigation was to meet both internationally accepted standards and codes of practice, and also to satisfy the Chinese requirements. Extensive use of local experience was utilised. Where possible geological drilling information was incorporated into the assessment. Extensive geotechnical mapping of surface and underground exposures, and index testing to gain an appreciation of rock intact strength were used to characterise the sites. Rock mass classification (MRMR) was used to assess indicative overall slope angles and appropriate bench stack heights for the proposed pits at Jinlonggou and Qinlongtan. Measured discontinuity orientations were used in kinematic analysis to assess stability of possible pit slope geometry at a batter and overall scale to provide preliminary recommendations for the pit slope configuration. Numerical modelling was also carried out to improve the understanding of anticipated pit behaviour. Site investigation and preliminary geotechnical design details, that incorporate site specific conditions for the formation of open pits at Tanjianshan, are discussed in this paper.

Jan 1, 2006

By T. Orupold

This paper covers the commercial development of gravity separation of fine particles using a Lamella High Shear Rate REFLUX? Classifier (REFLUX? Classifier), focusing primarily on coal applications. The REFLUX? Classifier is a fluidized bed device that incorporates a system of closely spaced parallel inclined channels located above the fluidized bed. These channels make it possible to achieve a significant suppression of the effects of particle size, resulting in a highly effective separation on the basis of density. The improved gravity separation performance is shown to be remarkably high, with a significant reduction in the variation of separation density with particle size, and a significant reduction in the change in Ecart probable error (Ep) with size. The first full commercial-sized units of the REFLUX? Classifier were field-tested in late 2009 in coal applications. More recently, the technology has been applied in fine particle separation in minerals applications and there are a number of full-sized units operating in chrome applications in South Africa. Initially, pilot-scaled units (typically the RC?300) were trialled in iron ore, mineral sands, and manganese plants amongst other minerals, typically after other technologies failed to achieve the desired results. Currently a number of laboratories globally are carrying out more testing in minerals applications. More than 50 RC? units are now operating in coal and minerals applications. This paper introduces the REFLUX? Classifier technology, identifies commercial applications, and gives some commercial results.

Jan 1, 2014

By T. Z. Mugodi, D. R. Fleming

Information and Communications Technology (ICT) is defined as ‘The goods and services that support the electronic display, processing, storage and transmission of information’. Early in 2002 the South African Department of Trade and Industry (DTI) commissioned a study into the diffusion and adoption of ICT in eight sectors of the economy. The platinum mining Sector was one of these. The key findings presented in this paper are based on the platinum sector component of that study. The paper examines the theoretical basis behind technology transfer and innovation diffusion and presents the results of an ICT diffusion survey carried out in the South African platinum mining sector. ICT is shown as the modern day technological tool which is an accelerator of economic development. The current state of ICT diffusion in the platinum mining sector is defined and projections for the near future are given. Recommendations which will ensure smooth and full adoption are presented and justified.

Jan 1, 2003

The Department of Mineral Resources of Thailand is organising, on behalf of the Government of Thailand and the International Tin Council, the Second Technical Conference on Tin. The Conference will be held at Sala Santitham, Bangkok from 18th to 22nd November, 1969. Papers will be grouped under three main headings: (i) Geology and prospecting; (ii) Mining and ore dressing; (iii) Miscellaneous, e.g. stimulating production, metallurgy, estimation of reserves etc. Pre-prints of papers will be circulated. A field trip to Southern Thailand has been arranged for 25th November to 2nd December, 1969. Details of the Conference and the field trip can be obtained from Mr. W. Fox, International Tin Council, Haymarket House, 28 Haymarket, London, S.W.l, England.

By M. Sanchez, I. Imris, G. Achurra

The Smelting and Converting El Teniente Process for copper concentrates as well as Slag Cleaning Furnace Technologies to treat slags coming out from the El Teniente Furnaces are widely applied today in Chile and around the world. Several industrial applications of this process have shown their capability to treat copper concentrates in a wide range of chemical and mineralogical compositions. Main operational parameters determining performance of the process are: oxygen enriched air flow rate, degree of oxygen enrichment, moisture content of the solid materials processed, molten material levels inside the vessel, frequency of molten materials tapping, bath temperature and copper losses in slags. In this work, the copper losses in the slags from El Teniente pyrometallurgical process are predicted by calculation from thermodynamic data and compared with those determined by microscopic examination and slag industrial data. Results obtained show that the main part of copper losses in the slag from El Teniente Furnace are mechanically entrapped or floated unsettled droplets of the coexisting matte phase. by the contrary the very low copper losses in the slag from slag cleaning furnace are limited by the physico-chemical form.

Jan 1, 2004

By C. G. Anderson

"As demand for copper and precious metals continues to grow, the need to develop new supplies increases. In the imminent future, the new large global ore bodies are more complex, with enargite, tennantite and tetrahedrite as the abundant contained mineralogy. These resources also contain considerable gold and silver. As such, direct treatment by conventional smelting is prohibitive due to the potential environmental impacts and copper quality issues. This paper outlines the effective application and associated economics of industrially proven Alkaline Sulfide Leaching (ASL) hydrometallurgical technology to an enargite concentrate for selective removal and recovery of arsenic, antimony, gold and silver, leaving a clean high-grade copper concentrate. The fundamentals behind the technology are described, along with those of hydrometallurgical arsenic fixation and stabilization. Flowsheets and unit operations are elucidated, along with an in-depth economic analysis. INTRODUCTION Hydrometallurgical methods can be employed for treatment of gold-, arsenic-, antimony-, tin- and mercury-containing materials, concentrates and ores, as well as complex ones containing any number of metals (Conner & Anderson, 2013). The alkaline sulfide leaching (ASL) system is one of these. It is essentially a mixture of sodium sulfide and sodium hydroxide with other meta-stable alkaline species as required. This is a unique hydrometallurgical system beause it is a very selective lixiviant for the distinct leaching of tin, gold, antimony, arsenic, tellurium, silver and mercury (Anderson, 2000, 2001a, 2001b, 2002, 2003, 2012, 2014; Anderson & Twidwell, 2008a, 2008b, 2010; Anderson et al., 2004, 2005; Glazkov & Tseft, 1961; Gnatyshenko & Polyvyanni, 1961; Nadkarni et al., 1975; Nadkarni & Kusik, 1988; Polyvyanni, 1963). Worldwide, ASL technology has been employed industrially in the former CIS, China and the United States for the production of antimony (Anderson et al., 1992, 1994; Anderson & Krys, 1993; Holmes, 1944; Kaloc, 1967; Nordwick & Anderson, 1993; van Stein, 1971)."

Jan 1, 2015

By V. Brabie, S. Jansson, L. Bohlin

The rate of dissolution of solid MgO-C and doloma into liquid in CaO-Al2O3-SiO2-MgO slag at different temperatures was studied under conditions of forced convection by rotating cylindrical refractory specimens in a stationary crucible containing the molten slag. The corrosion rate was calculated from the change in diameter of the cylindrical specimens. Refractory specimens were 13 mm in diameter and 70 mm long. The specimens were rotated for15 to 120 minutes at speeds of 100 to 400 rpm in the molten slag. The rate of corrosion increased with temperature and with the rotating speed of the rod, and decreased when the slag was nearly saturated with MgO. The experimental results confirm the assumption that the diffusion of magnesium oxide through the slag phase boundary layer controls the corrosion process. The corrosion mechanism seems to be the dissolution of the refractory materials into the slag, followed by penetration of pores and grain boundaries and dispersion of the grains in the slag. Keywords: MgO-C refractory, doloma refractory, molten slag, corrosion rate, corrosion mechanism

Jan 1, 2004

By M. J. Santofimia

Multiphase microstructures in steel have been intensively studied in the past years, but combining non-equilibrium phases still offers a great potential for further development of these steel grades. Thus, improved combinations of mechanical properties can be obtained with microstructures formed by bainite or martensite, in combination with retained austenite. In particular, microstructures on the basis of carbon-depleted martensite and retained austenite can be produced by the very promising production process named quenching and partitioning (Q&P). Originally, the Q&P process aimed to avoid the formation of bainite during the heat treatment. However, the process does provide the possibility for (carbide-free) bainite formation during the partitioning step, i.e. in the presence of martensite. This article evaluates this approach, considering thatthe formation of bainite from austenite is strongly influenced by the preceding formation of martensite. Although the accelerating effect of the presence of martensite during bainite formation has been observed, it is not yet fully understood, and experimental and theoretical studies are being performed in order to come to a more effective exploitation of these processes for the formation of multiphase microstructures.

Jan 1, 2013

By H. A. D. Kirsten

Written contribution by L.J. Besaanst I am a Mechanical Engineering Technician (T3), and wish to further my education to at least NHD (T4) level. I read your paper in the Journal of The South African Institute of Mining and Metallurgy with great interest, and must compliment you on its brilliance. However, there are some questions I should like to ask, and certain points I should like to highlight. I should appreciate your comments. Written contribution by J.F. Curtis The comprehensive and finely detailed survey of, and proposals for, engineering education in South Africa reflects the author&apos;s wide experience in the needs for, and the provision of, such education. This paper wil make a major contribution to the enhancement of the profession of engineering and the improvement in quality of engineering activities in South Africa. Contribution by G.W. Annandalet I have studied your paper in some detail, and am of the opinion that it makes an important contribution to the topic of the development of technological manpower, which is currently being debated in South Africa at al levels. Debate on this topic has risen above the level of academic discussion; it has been discussed by the Economic Advisory Council of the President, and is being considered at Ministerial level. Author&apos;s reply to L.J. Besaans Thank you for your contribution and complimentary remarks. As you have pointed out, there are certainly many aspects that will have to be addressed in the resolution of the crisis in engineering education. I trust that the following comments satisfactorily answer the queries you have raised. Author&apos;s General Comments Since publication of the paper, attention has become focused on the provision of employment opportunities an aspect not dealt with specifically in the paper. The following comments serve to indicate some of the directions in which job opportunities will have to be developed in the numbers that will be required.

Jan 1, 1991