Search Documents

By R. Weber

Methane explosions in underground coal mines are a major concern across the mining industry. After the Pike River disaster, Arnot Coal became even more aware of the explosion risk. To determine whether Arnot has adequate precautions against a methane explosion, such as the one that led to the Pike River disaster, a literature survey covering the causes of the incident and what preventative measures should have been in place was conducted. Many different methane explosion prevention methods were evaluated, as well as codes of practice. Based on the findings, Arnot?s measures to prevent conditions favourable for a methane explosion were evaluated.

Jan 1, 2014

By A. P. Squelch

The high incidence of accidents and fatalities in the South African mining industry, in particular those associated with falls of ground, is often attributed to ineffective and/or inappropriate training methods and material. Recently introduced mine health and safety legislation in South Africa also requires that all mine workers receive appropriate and effective training to enable them to operate safely in their given mining environment. There can, therefore, be no doubt that methods to provide effective training, in particular safety related training, are urgently required in the South African mining industry. In the search for alternative and improved training approaches, attention has fallen on virtual reality (VR) technology as a possible solution. VR has found acceptance in a number of industries as an effective method of training for a variety of work place activities, including those of a safety related nature. VR has successfully been applied in a number of industries to improve the effectiveness of safety and hazard awareness training. The CSIR: Division of Mining Technology (CSIR Miningtek), in conjunction with the Safety in Mines Research Advisory Committee (SIMRAC), therefore evaluated the potential of VR to be used as a training medium in the South African gold and platinum mining industry. Aspects of the evaluation included an assessment of the technical capability of VR to represent a typical underground mining environment with sufficient realism and the relevance of the VR training concept for a largely illiterate workforce. For these purposes, a prototype PC-based VR hazard awareness training simulator has been developed by CSIR Miningtek, and a series of evaluation sessions conducted at a typical deep level gold mine. The conclusion from this evaluation work is that virtual reality technology has the potential to provide effective training systems that are relevant to the South African mining industry. Keywords: Virtual reality, mine training, safety training.

Jan 1, 2001

By J. U. Burger

The Elizabeth Bay aeolian deposit in Namibia comprises a sedimentary package of diamondiferous grits that have been deposited, reworked and concentrated to various degrees by dominant southerly winds. Diamond concentration in these deposits is highly variable and often unpredictable. The deposit is marginal from an economic perspective and therefore requires selective mining which in turn requires correct sampling and accurate estimation. Three methods of sampling have been used at Elizabeth Bay for mineral resource estimation: (i) pit samples utilizing an excavator to produce a sample 1 to 3 metres deep with a 10 to 20 m2 footprint, (ii)GB50 grab sampling with a 3.34 m2 footprint and (iii) a BG36 bucket auger drill with a 5 m2 footprint. Pit sampling, being easy to execute, has been the most widely used despite a limited penetration ability and, at times, questionable integrity. The GB50 grab sampling tool was tested at Elizabeth Bay and although it had better penetration ability and sample integrity, it struggled with cemented horizons. No sample optimization was conducted prior to the GB50 grab sampling. The latest phase of sampling was conducted using a BG36 bucket auger drill which is capable of penetrating thick overburden, penetrate cemented horizons and provides an acceptable sample support size. Geostatistical simulation methods were applied to establish the optimum sampling parameters required to estimate a mineral resource at an indicated level of confidence. The results show that a 5 m2 sample support size is adequate and that a 50 m 100 m sample configuration is optimal. Sample data obtained from the three methods confirms that the BG36 bucket auger tool combined with the parameters identified in this exercise produce the best results for diamond resource estimation.

Jan 1, 2009

The aim of this research was to study the absorption characteristics of thermally dried fine coal from South African collieries. After milling to ?150 µm and pressure filtration, the samples were subjected to either air drying or thermal drying at 150°C. The samples were then put into a climate box at 28°C and at three different relative humidity levels, namely 30, 60 and 94 per cent. It was found that the equilibrium moisture content of thermally dried coal at a specific relative humidity was lower than that of air dried coal. The relationship between the equilibrium moisture content and relative humidity is described by 1 ? RH = exp (-KTMen). There was no relationship between the volatile matter content and equilibrium moisture content, but there was an increase in the equilibrium moisture content of the coal with an increase in mineral content. The moisture uptake rate increased with an increase in temperature and a decrease in particle size. A model is discussed that fitted the experimental data and gave a good prediction for changes in the conditions. There was no evidence of greater moisture absorption by thermally dried coal. Keywords: Fine coal, thermal drying, drainage, South Africa, drying

Jan 1, 2002

By G. M. Cresswell

The 2 360 t/h two module Phola coal preparation plant represents anew era of large plant in the Witbank coalfield designed to extend its life to 2020 and beyond. The plant uses the optimum processing model for Witbank coals, receiving a feed coal size of -50 mm, wet screening it into coarse and small coal fractions 50 x12 and 12 x0.63 mm before processing them in parallel through two primary DM cyclone sections, in order to make a 27.5 MJ/kg export floats product. The sinks are processed through a common high density DM cyclone section to produce a 21.5?23 MJ/kg thermal coal middlings product. The plant design incorporates the largest size DMS equipment used to date in South African coal preparation plants, i.e. 1 150 mm large diameter pump fed DM cyclones and 4.2 m width banana screens. The fine coal is conventionally processed by spirals, whereas the raw coal slimes are filtered using automated plate and frame filter presses and added to either the middlings or discards depending on its quality. The paper describes the database, innovative design concepts, construction, and commissioning.

Jan 1, 2010

Rock mass classification systems are extensively used in rock engineering design work, and mine design is no exception. Among the systems most widely used for mining-related design work are the NGI 0-system (Barton et al., 1974), the RMR system (Bieniawski, 1976), the MRMR system (Laubscher and Taylor, 1976) and, more recently, the GSI system (Hoek et al., 1998). Classifying the rock mass is widely seen as being the fieldwork required to characterize the rock mass and enable the application of empirical design methods associated with the different classification systems. This paper argues that it is fundamentally important to recognize the distinction between rock mass characterization and rock mass classification. These two processes should, in most cases, be separated from each other. Rock mass characterization should be used to determine the intrinsic properties of the rock mass independently of the application; i.e. independent from the infrastructure to be designed, the size, shape, and orientation of the excavation(s) or pillar(s), etc. Rock mass characterization should also be compatible with most classification systems and empirical design methods to be used. Rock mass characterization is the background fieldwork required to perform rock mass classification and/or engineering design work. Rock mass classification is the subsequent step to the characterization, and an integral part of the design process. Parameters that vary according to the design, such as the relative orientation of geological structures compared to the opening or the mine-induced stresses, should be calculated as part of the rock mass classification and design process, rather than during the rock mass characterization process. The failure to distinguish between rock mass characterization and rock mass classification can lead to major design errors and poor results.

Jan 1, 2012

This paper describes the extraction of gold, as the anionic aurocyanide complex, from solution by strong- and weakbase anion-exchange resins. The effects, on the rate of extraction and the loading capacity for gold, of parameters such as pH, temperature, ionic strength, agitation, and the presence of competing anions are reported. The elution and regeneration of strong- and weak-base resins will be examined in a second paper. A third paper in this series will present the results of several smallscale pilot-plant investigations carried out with strong- and weakbase resins In cyanide pulps from various South African gold mines, and will compare the metallurgical performance of resin-In-pulp with that of the carbon-in-pulp process.

Jan 1, 1984

By P. Vlasak, Z. Chara

Since the flow behaviour of slurry containing both coarse and very fine particles has not been sufficiently clarified, the paper focuses on the experimental study of the particle size distribution, time and intensity of shearing and the effect of chemical agents on the hydraulic gradient versus the average velocity relationship of fluidic ash slurries in the laminar and turbulent regimes. The recirculation pipe loop with smooth stainless steel pipes of inner diameters 26.8 and 36 mm was used for measuring the ash-water mixtures flow parameters. The dense fluidic ash-water mixtures behave as time dependent non-Newtonian slurries. Shearing, the addition of bottom ash or chemical agents, favourably affects the flow behaviour of dense fluidic ash-water slurries. The hydraulic gradient in the laminar region significantly decreases; also the laminar/turbulent transition region is reached for lower flow velocity.

Jan 1, 2007

By L. Gunnewiek

An advanced real-time monitoring system called the tapblock diagnostic system (TDS) has been developed. The purpose of the TDS is to help furnace operators manage the safe operation and economical maintenance of furnace tapblocks. This system is an evolution of the current practice of using historical records and operator interpretation to assess the ?health? of a tapblock. The main parameters affecting tapblock health are heat removal capacity and refractory wear, and these are currently difficult to assess in situ except in a global way. By using monitored and operating data together with predictive numerical modelling and multivariate statistical methods, real-time tapblock performance is assessed relative to expected performance. A state indicator in the form of a green, yellow, and red light is used by furnace operators to monitor the tapblock performance and health status during operation. Access to historical operating data and the provision of diagnostic functions allow for probable health degradation events to be deeply investigated. A recent opportunity to evaluate the actual performance of a first generation TDS installed in the KIVCET furnace at Teck Cominco?s Trail Operations showed that a reasonable estimate of tapblock health was made. However, the evaluation also found that some areas of refractory wear were missed, and a new mechanism affecting refractory wear was discovered that was not previously known. This has reinforced the belief that there is a need to develop improved methods of monitoring so that data used to define the health of the tapblock is more comprehensive and accurate.

Jan 1, 2008

Interest in the potential use of high-density, thickened tailings has recently increased significantly. Reasons for considering this new technology vary across projects, but commonly include the need to conserve water, perceived lower risk of catastrophic failure, potential easier closure, or even reduced overall costs. As with any new technology, there has been some tendency to overstate its potential benefits. This paper reflects on whether or not the potential benefits that have been attributed to paste and thickened tailings have been realized. Using a grading system, thirteen benefits that were ascribed to the new technology some years ago are evaluated. Data is taken from case studies, and it is suggested that the key proven benefits appear to be reduced operating costs in some cases, reduced wall-building costs, and reductions in water consumption. One key potential benefit that has not been universally achieved is a reduction in the footprint of the tailings facility. Reports in the literature highlight the sometimes confusing nature of trade-off studies. Unless full life-of-mine costs are considered, these studies can be misleading and incorrect. The need to establish a consistent basis for comparative studies is discussed.

Jan 1, 2012

The Proceedings of the above Symposium have been edited and published by the Symposium Committee. The Symposium was sponsored by the Australian Coal Association, the Joint Coal Board, and the United Nations Economic Commission for Europe. The Symposium was very well attended, with presentations from fourteen countries, including all the major coal-producing countries of the world. The Proceedings are presented in two parts: the Symposium Part and the Workshop Part. The Symposium Part deals basically with the theoretical aspects of outbursts and high-gas emissions in mines, while the Workshop Part is more practically oriented and describes case studies, and the management systems, and drilling technologies used in underground mines.

Jan 1, 1996

By H. Knorre, A. Griffiths, R. Higgins, S. Gos

Hydrogen peroxide is gaining acceptance as a reagent for the treatment of mining effluents containing cyanide. In this paper some of the chemical and environmental aspects of treatment with hydrogen peroxide are discussed, and one way of improving the economics of the process is described. This is known as selective detoxification, which involves the oxidation of the less stable (cyanide) complexes while not affecting the more stable complexes, which contribute very little to the concentration of free cyanide or to the toxicity of the treated water.

Jan 1, 1987

By R. Romano, E. Montalar, J. B. Serón

The SMR geomechanics classification system (adaptation of RMR for slopes) is reviewed with data from 87 actual slopes in Valencia. In a research project, SMR has been applied by a GIS system, as a method to forecast stability problems in future road construction. As a result of this work a methodology for GIS application has been developed. On revient sur la classification geomechanique SMR ( une adaptation du RMR pour talus et pentes) avec les dates de 87 talus existant autour de Valencia. Dans le cadre d’un projet de recherche SMR a été appliquée, avec un système GIS, comme méthode de prévision de stabilité problèmes dans la construction de futures routes. Une méthodologie pour l’application du GIS a été développe. Das Geomechanische Einteilungssystem SMR (eine Anpassung des RMR an Böschungen) wird an Hand der Daten von 87 Böschungen im Gebiet von Valencia überdacht. In einem Forschungsprojekt wurde das SMR in einem Geographischen Informationssystem (GIS) als Methode zur Vorhersage von Stabilitätsproblemen bei zukünftigen Straßenbauprojekten eingesetzt. Das Ergebnis dieser Arbeit ist die Entwicklung einer Methodologie für die GIS-Anwendung

Jan 1, 2003

By B. B. Tati

The project report is based on vacation work done by the writer at the Khutala Colliery during December/January 2009?2010. The purpose of this report is to explain and describe the design process in a multi-seam mine design for coal extraction at the Khutala Colliery. The multi-seam design will focus on the No. 2 and No. 4 seams as these are the seams that are currently being mined by underground methods at Khutala Colliery. The seam thicknesses and the parting thickness between the seams provide suitable conditions for designing a multi-seam mine design. An investigation into the pillar design aspects is carried out followed by a numerical modelling analysis of various scenarios. This analysis validates the first principles approach provided by multi-seam design guidelines. The design results from the analysis of the selected pillar design indicate sufficient parting for primitive conditions between seams, thus illuminating the need for superimposing in-panel pillars. This multi-seam mine design confirms the potential for the extraction of coal in a new panel. The design indicates that significant amounts of power station coal are present and suitable for extraction by room and pillar mining methods. The panel block indicates 401 625 tonnes of ROM coal. This block has a life of panel that will be mined just over a 4-month period. This 4-month period is assumed to mined at a production rate of 48 000 tonnes per month. The total capital cost required for the new panel is R48 281 127.05. Keywords Multi-seam mining, panel design, ventilation flow, superimposition.

Jan 1, 2011

By W. F. McKechnie

"Southern Africa is generally thought to be well explored, with only limited potential for major new diamond discoveries. However, Chiadzwa in Zimbabwe and reports of a significant new kimberlite find in Angola are testimony to the dangers attached to an attitude that ‘there is nothing left to find’.Since the major discoveries in the central interior of South Africa in the 1870s, diamond exploration in the region has been led by market and political factors that influence the key exploration drivers of opportunity and value proposition. Unexpected new discoveries by new players always impact on existing producers and, from time to time, denial of opportunity through political or protectionist policies has inhibited investment in exploration.Entrepreneurial exploration appetite in southern Africa will be tempered by the potential value equation and security of investment. Overlaid on this, developments in diamond recovery technologies provide opportunity to reinvigorate current mines and old prospects previously considered too difficult or costly to exploit. Position on the cost curve will remain a key factor for survival in an increasingly competitive environment. IntroductionThe diamond industry in southern Africa boasts a history of 150 years of discovery and mining, forming the cornerstone of development of the core, modern economies at the southern tip of Africa.Since the discovery, in the 1860s and 1870s, of the secondary diamond placers and primary diamond-bearing kimberlite deposits in the central interior of the then Cape Colony and Orange Free State, southern Africa has endured as the pre-eminent diamondproducing region in the world. Notwithstanding periodic competition from significant new discoveries in other parts of the globe and the paucity of recent, new discoveries in the region, its ranking is unlikely to change in the short to medium term.In a geological context the region contains the Kaapvaal-Zimbabwe and Angola-Kasai cratons, identified in terms of Clifford’s rule as areas inherently prospective for diamonds, being underlain by portions of the Earth’s crust that are tectonically stable and older than 1.5 billion years (Clifford, 1992). Although the Democratic Republic of Congo (DRC) would, in a geographic context, be considered to be part of Central Africa, for the purposes of this review it is included in southern Africa since northeast Angola and the adjacent parts of the DRC form part of the same geological terrane and diamond production from both countries needs to be considered together. Historical and current diamond production from the northeastern parts of the DRC around Kisangani is not considered to be significant and its inclusion in the overall numbers for the DRC does not materially affect the overall picture presented here."

Feb 1, 2019

By J. Markgraaff

Because composites offer new solutions to materials problems, they are currently the focus of intense research and development worldwide. However, the natural tendency of users is to remain with tried materials in every situation of material selection. This approach ignores the tremendous advances that have been made in composite materials and their application. These advances enable engineers to tailor composites to suit specific applications such as the demanding needs of mining and industry in South Africa. However, the application of composites, where new and improved components and products are needed or are being developed is often hampered by the limited knowledge and experience of the engineers concerned. This paper presents some of the basic information needed for an appreciation of the terminology, definitions, and properties of various types of composites. It also reviews recent developments in manufacturing technology and product development that may find application in local industries and mining.

Jan 1, 1996

By Z. Weisheng

The lift system is the main part in manganese nodule mining on the ocean bed. It connects the nodule collection system (miner) with the surface platform (mining vessel) and transports the nodules from the ocean bed to the surface. China started the research on lift technology in deep ocean mining in 1991, and a slurry pump hydraulic lift method has been developed for the nodule mining system. The detailed slurry pump hydraulic lift experiments have been undertaken with crushed nodules in the vertical pipe. The lift parameters to lift coarse particles in the lift pipeline have been discussed, including the pressure drop, the solid concentration, and the mixture velocity. The author of this paper not only took part in all these studies on the lifting technology, but was also responsible for some of this research. This paper will present the component parts of the lift system and the research results of coarse particle mixture flow in the vertical lift pipeline. Keywords: deep sea mining, slurry pump lift, lifting parameters.

Jan 1, 2007

By R. Altindag

In rock cutting mechanics, the effects of the rock and coal brittleness on the efficiency of cutting bits are examined by many researchers. There is no universally accepted brittleness concept as a measure of cutting efficiency. The effect of the brittleness on rock cutting has not been completely explained. The aim of this study is to correlate the relationships between Specific Energy (SE) and brittleness concepts. The applicability of various brittleness measurement methods for rock cutting efficiency has been investigated. In this study, the raw data derived from previous experimental studies were used, and the relationships between SE and brittleness concepts were investigated. The two previously used brittleness concepts, which are named as B1 (the ratio of compressive strength to tensile strength) and B2 (the ratio of compressive strength minus tensile strength to compressive strength plus tensile strength), and a new introduced brittleness concept named B3 (the area under line in relation to compressive strength and tensile strength) were evaluated in this study. The relations among these brittleness concepts for rock cutting efficiency were established using regression analysis. There is no correlation found between the SE values and the brittleness of B1and B2values. But, the SE is strongly correlated with the brittleness of B3. It was seen that the suggested brittleness of B3concept could be used as an indicator in rock cutting efficiency analysis.

Jan 1, 2003

By K. Levin, P. Lloyd

During the commissioning phase, which is usually the most exciting part of a project involving the design and construction of metallurgical plant, the commissioning engineers interact between the client and the project management. The client wants to see whether all the equipment that he has bought and that, in his opinion, has taken far too long to erect will actually work. Project management expects the commissioning people to con¬vince the client that this is the best design ever developed and that never before have time and money been spent so well. The commissioning team has to fulfil these expectations. Commissioning work is a `shirt sleeve' function, with little of the glamour that is normally associated with fields such as engineering and operations. The team usually works in a partially completed plant with more temporary than permanent services and little (if any) office accommodation, normal working hours do not apply, and the demands made on the team change suddenly and dramatically. This article outlines the activities of the commissioning group and the systems used to smooth the commissioning path.

Jan 1, 1981

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012