Search Documents

By P. Ramsaywok, G. Legodi

Spiral concentrators are widely used in the coal industry treating fine (-1mm) coal. Their application was a limitation to the product quality until the introduction of low-cut spirals which allow a lower quality ash product to be produced, thus expanding the market. The Exxaro Grootegeluk 1 (GG1) plant has a two-stage traditional rougher-cleaner spiral circuit using conventional SX4 spirals to produce semi-soft coking coal product at 12.5% ash by mass. The overall plant product is 10.3% ash meaning that the coarser sized coal dense medium separation circuits must compensate. A low density cut-point spiral targetting 10.3% ash would thus be beneficial to the overall complex. The spirals were tested in the two-stage plant environment and in a pilot plant. This paper discusses the findings and compares a two stage four-turn low density cut and conventional spiral. The two spiral technologies were unable to sustain a 10.3% ash product. Pilot test work was also conducted on GG1 coal, demonstrating that an eight-turn low density cut-point spiral achieves the targetted 10.3% ash under controlled conditions. Keywords: Spiral, low-cut, coal

Jan 1, 2020

By J. U. Burger

The Elizabeth Bay aeolian deposit in Namibia comprises a sedimentary package of diamondiferous grits that have been deposited, reworked and concentrated to various degrees by dominant southerly winds. Diamond concentration in these deposits is highly variable and often unpredictable. The deposit is marginal from an economic perspective and therefore requires selective mining which in turn requires correct sampling and accurate estimation. Three methods of sampling have been used at Elizabeth Bay for mineral resource estimation: (i) pit samples utilizing an excavator to produce a sample 1 to 3 metres deep with a 10 to 20 m2 footprint, (ii)GB50 grab sampling with a 3.34 m2 footprint and (iii) a BG36 bucket auger drill with a 5 m2 footprint. Pit sampling, being easy to execute, has been the most widely used despite a limited penetration ability and, at times, questionable integrity. The GB50 grab sampling tool was tested at Elizabeth Bay and although it had better penetration ability and sample integrity, it struggled with cemented horizons. No sample optimization was conducted prior to the GB50 grab sampling. The latest phase of sampling was conducted using a BG36 bucket auger drill which is capable of penetrating thick overburden, penetrate cemented horizons and provides an acceptable sample support size. Geostatistical simulation methods were applied to establish the optimum sampling parameters required to estimate a mineral resource at an indicated level of confidence. The results show that a 5 m2 sample support size is adequate and that a 50 m 100 m sample configuration is optimal. Sample data obtained from the three methods confirms that the BG36 bucket auger tool combined with the parameters identified in this exercise produce the best results for diamond resource estimation.

Jan 1, 2009

By S. Stuurman

Inorganic acids such as sulphuric acid have found use together with certain reducing agents in leaching of copper-cobalt oxide ores. These reagents are not ideal due to the adverse effect the inorganic acids generally have on the environment and the high costs of the reducing agents. In this study a copper-cobalt oxide ore from the Central African Copperbelt was leached in two different environments; sulphuric acid in conjunction with hydrogen peroxide as a reducing agent and tartaric acid. The effects of acid concentration, reducing agent concentration, and temperature were independently determined for both leaching environments. The sulphuric acid concentration was varied between 0.4 M and 1.2 M and the concentration of hydrogen peroxide between 4.0 M and 6.5 M, while the tartaric acid concentration was varied between 0.15 M and 0.35 M. The temperature was varied between 20°C and 50°C. The results showed that the extraction of both copper and cobalt increased with sulphuric acid concentration, reaching a peak at approximately 0.8 M and then decreasing at higher acid concentrations. A similar increase and decrease in metal extraction was observed when the reducing agent was increased. In leaching with tartaric acid, the extraction of cobalt was much higher than that of copper, although extraction of both metals increased with acid concentration. Additions of small amounts of hydrogen peroxide were found to increase cobalt extraction in tartaric acid but had a minimal effect on copper. An increase in the solution temperature had a significant effect in the organic acid environment, with the effect on cobalt extraction being much more pronounced than on copper.

Jan 1, 2014

By J. Petersen, A. E. Lewis, J. Chivavava

Rare earth elements (REEs) have special properties that prompted their extensive use in high-tech applications. The demand for REE has, therefore, increased over the past years, resulting in the supply risk of the materials. Extraction from non-conventional low-grade ores, like easy-to-mine ion adsorption clays (IACs), by hydrometallurgical methods is being explored to supplement the supply of REEs. The extraction of REEs from low tenor IAC leach solutions requires enrichment using cost-effective methods such as precipitation. Therefore, the aim of this study was to understand the recovery of REEs from IAC leach solutions using various reagents for precipitation. In the first part of the study, recoveries of REEs from IAC leach solutions through direct precipitation using H2C2O4 and NH4HCO3, as well as antisolvent crystallization using C2H5OH, were predicted via thermodynamic modelling using OLI Stream Analyzer. Verification experiments were then conducted through the use of an agitated reactor. Simulation results showed that high yields of REEs were possible using each of the reagents, but large quantities of C2H5OH were required. Experimental results confirmed the high yields predicted from simulations. Precipitation with H2C2O4 was found to selectively recover REEs while rejecting Al. However, utilization of NH4HCO3 and C2H5OH resulted in the co-precipitation of Al. Furthermore, the yield of Y from antisolvent crystallization was significantly lower than the theoretical value. The product recovered from antisolvent crystallization consisted of well faceted, large crystalline particles, which filtered faster than the fine, amorphous REE carbonates recovered using NH4HCO3. REE oxalates were crystalline, larger than the REE carbonates and, overall, showed the highest filtration rate.

Dec 11, 2024

By F. Lombard

We consider in this paper the use of a modified version of Hotelling?s statistic in the analysis of particle size distributions. The statistic can be adversely affected by the presence of outliers among the data. We propose a competitor to the statistic that is based on ranks, and hence is less sensitive to outlier effects. The results of a Monte Carlo study suggest that the rank test is highly competitive with the Hotelling test in its ability to detect differences between two mass size distributions. The calculation of the rank statistic is explained in detail and its application is illustrated on two sets of data.

Jan 1, 2012

By F. Lombard

We consider in this paper the use of a modified version of Hotelling?s statistic in the analysis of particle size distributions. The statistic can be adversely affected by the presence of outliers among the data. We propose a competitor to the statistic that is based on ranks, and hence is less sensitive to outlier effects. The results of a Monte Carlo study suggest that the rank test is highly competitive with the Hotelling test in its ability to detect differences between two mass size distributions. The calculation of the rank statistic is explained in detail and its application is illustrated on two sets of data.

Jan 1, 2012

By A. A. Debrah

Artisanal and small-scale mining (ASM) plays a fundamental role in the national and local economies of resource-rich countries in Africa. As such, more effort must be geared towards fostering this type of economic activity to sustain livelihoods in rural communities. Across Africa, efforts to operationalize ASM based on a sustainable development framework have been quite tedious and often ineffective. This is because most of these frameworks lacked context and an understanding of the continuum from the artisanal through small-scale and up to the junior miner, grouped under the general term ?ASM?. Driven by the need to contextualize some of the definitional issues in this niche sector, and gain a clearer understanding of their peculiar challenges, this paper aims to contribute to the debate on ASM by considering two of Africa?s resource-rich countries ? Ghana and South Africa. Since South Africa has made greater inroads in protecting the interests of small-scale miners, we thus draw comparisons from both countries? approach to ASM, outline the lessons learnt, and provide recommendations regarding the ways forward.

Jan 1, 2014

By A. Refahi

For predicting the energy consumption during the size-reduction process, the Bond approach is often used. In this work, the PFC3D discrete element method (DEM) software was employed to model the crushing behaviour of some rocks with different mechanical properties in a laboratory jaw crusher. FLAC3D software was adopted to analyze the stress distribution in the rocks. The rocks studied were modelled as granular assemblies in the shape of a sphere and/or a cube located between two jaws, and the work done by the jaws in the crusher was determined. Nine different types of rocks were studied and the energies consumed by the crusher were compared to those of the Bond comminution energy estimated from the Bond index. There is considerable difference between Bond crushing energy and work done by the jaw crusher for rocks. It appears that the Bond approach is not a suitable method for predicting single particle fracture energy done by the crusher. To verify the results obtained from DEM models, the fracture behaviour of the crushed rocks was examined and was compared to the PFC3D results. The tensile mode of fracturing is favourably modelled by the PFC3D software while the delamination mode cannot be well modelled by PFC3D software. Keywords: jaw crusher; discrete element method; crushing energy; Bond index

Jan 1, 2009

By M. Le Roux, Q. P. Campbell, M. Fofana

The determination of densimetric information to predict coal washabilities is an important step in characterising the feed material, as well as the performance of operating plants. However, traditional methods like float-and-sink analysis are hazardous and time-consuming. This is especially true for finer particle size ranges, where very long settling times are required in a medium. De Beers Technologies recently developed a density analyser, known as the RhoVol, for use on diamondiferous kimberlite. Operating over size ranges from 25 mm down to 3 mm, it can determine the mass, volume, density, size and shape of all the particles in a given population and is thus able to provide information about the densimetric distribution on a single particle basis. A study was carried out to compare uncalibrated and calibrated RhoVol results to densimetric and size data obtained using traditional zinc chloride float-sink procedures, for three different coal samples in the size range 3 mm to 8 mm. The results indicate that the RhoVol can be used to provide simple, rapid and safe size-by-washability information for coal, provided proper pre-calibration is done, mainly to account for the effects of particle porosity in the density determination. Keywords: Coal washability determination, RhoVol, densimetric curve

Jan 1, 2020

By M. Shaw, H. R. Heydenrych, A. E. Lewis, E. Glass, J. Chivavava

The removal of calcium from the retentates of reverse osmosis (RO) treated minewater is desirable since it allows the recovery of both additional potable water (through RO) and higher-purity salts (in downstream processing). This, in turn, reduces the need for costly and unsustainable evaporation ponds and enhances the economics and operability of potential zero-liquid discharge downstream processes, e.g. evaporative-, cooling- and eutectic freeze-crystallisation. For this study, a multi-component retentate high in sodium content was considered, typical of those emanating from minewater reclamation plants in Mpumalanga, South Africa. Four technologies were evaluated to remove calcium: gypsum precipitation by addition of lime; calcium carbonate precipitation by addition of soda-ash; heating crystallisation of calcium sulphate anhydrite; and cooling crystallisation of gypsum. Full processes were developed and simulated using electrolyte thermodynamics. Using the results of these simulations, capital- and operating costs, as well as revenues were calculated and used in economic comparisons of the processes. Sensitivities to key purchasing and selling prices were also investigated to understand the impact of changes in these variables. For the case of a low magnesium-to-sodium ratio in the feed, gypsum precipitation through lime addition was found to have the lowest operating and total annualised costs; but, if revenue could be derived from the sale of sodium sulphate, calcium carbonate precipitation through soda-ash addition was favoured. Keywords: Calcium removal, gypsum precipitation, calcium carbonate precipitation, heating crystallsation, cooling crystallisation, economic comparison

Jan 1, 2020

By P. Michalcik, V. Petros, M. N. Bagde, K. Holub

The objective of this paper is to present some results of laboratory experiments during the investigation of stress-strain characteristics of Carboniferous sandstones at dynamic loading. During these experiments increasing frequency and the constant amplitude of dynamic loading and/or constant frequency at different amplitude of dynamic loading were applied. Der Gegenstand dieses Artikels ist, irgendeine von Ergebnissen von Laborexperimenten bei Messung der Spannungs- und Deformationscharakteristik der Karbonsandsteine bei ihrer dynamischen Belastung vorzustellen. Im Laufe diesen Experimenten wurden entweder anwachsende Frequenzen bei konstanter Amplitude der dynamischen Belastung, oder gleiche Frequenzen bei variabler Amplitude der dynamischen Belastung verwendet. L'objectif de ce papier est présenter quelques résultats d'expériences de laboratoire pendant l'enquête de caractéristiques de la tension – deformation de grès Carbonifère à sollicitation dynamique. Pendant ces expériences fréquence croissante et l'amplitude constante de sollicitation dynamique et/ou fréquence de la constante à amplitude différente de sollicitation dynamique ont été appliquées.

Jan 1, 2003

By T. Scheldt, M. Lu, A. Myrvang

Abstract: In this paper both continuous and discontinuous modelling are utilised in order to analyze the stability of the Gjøvik Olympic Mountain Hall. The large span cavern (62 m) was built for the 1994 Winter Olympic Games at Lillehammer, and is a unique case study because of the large amount of available input data, through a comprehensive pre-investigation, stress and deformation monitoring program before, during and after the excavation. Phase2, a two-dimensional non-linear finite element program, and the Discontinuous Deformation Analysis (DDA) are used as representative tools for continuous and discontinuous modelling, respectively. The analysis results are compared and discussed taking the reliability of the models, time-consumption and costs into consideration. Some guidelines for the total modelling process, from field measurements to final results, are also presented. Zusammenfassung: In diesem Artikel werden sowohl kontinuierlich als auch diskontinuierlich Modellierung verwendet, um die Stabilität, der in den Berg gebauten Olympiahalle in Gjøvik zu analysieren. Die Olympiahalle wurde 1994 zu den Olympische Spielen in Lillehammer errichtet. Ihr Dach erstreckt sich über eine Breite von zweiundsechzig Meter. Für den Bau wurden umfangreiche Daten durch Voruntersuchungen, und Überwachung von Gebirgsspannungen und Deformationen bevor, während und nach Exkavation eingesammelt. Auf Grund dieser großen Datenmenge stellt die Olympiahalle ein herausragendes Beispiel für den Bau ähnlicher Projekte dar. Für die kontinuierlichen Modellierungen wurde „Phase2“, ein zwei-dimensionales, nicht lineares „endlich Element“ Rechnerprogramm angewandt. Die diskontinuierlichen Modellierungen erstellte man mit Hilfe von der „Diskontinuierliche Deformations Analyse“ (DDA). Die Analysenergebnisse sind mit Rücksicht auf die Zuverlässigkeit der Modelle, Zeitverbrauch und Kosten verglichen und diskutiert worden. Im Artikel werden Richtlinien für den Modellierungsprozess von Dateneinsammlung bis Schlussfolgerung gegeben. Résumé: Dans cet article la modélisation continue et discontinue sont utilisés pour analyser la stabilité de Gjøvik Olympic Mountain Hall. Cette caverne de grande portée (62 m) a été construite pour les Jeux Olympiques d’Hiver de 1994 à Lillehammer, et est une étude de cas unique grâce à la grande quantité de données disponibles, de par un programme de pré-investigation compréhensive, monitorage des contraintes et déformations avant, pendant et après l'excavation. Phase2, un code d’éléments finis non linéaire à deux dimensions, et l’Analyse en Déformations Discontinues (DDA) sont utilisés comme outils représentatifs de la modélisation continue et discontinue, respectivement. Les résultats d'analyses sont comparés et sont discutés, prenant en compte la fiabilité des modèles, la consommation en temps de calcul et les coûts. Quelques indications pour le procédé total de modélisation, des mesures sur place aux résultats finaux, sont aussi présentées.

Jan 1, 2003

By N. Naude, L. S. Leal Filho, M. P. Tshazi

In this paper, the authors performed experiments in the Denver and Leeds laboratory flotation devices at the University of Pretoria at various particle sizes to evaluate the performance of the devices. Quartz was used in a single mineral system at discrete sizes fractions, -25 μm, +25- 45 μm, +45-75 μm, and +75-106 μm. Hydrodynamic analysis, based on dimensionless power and Reynolds numbers, indicated that the Leeds cell required higher power input to achieve comparable flow conditions. Specifically, the Leeds cell exhibited an average power number of 1.03, whereas the Denver cell averaged 0.77 within the same impeller speed range of 1000 rpm–1500 rpm. For comparative flotation performance, impeller speeds were calibrated, resulting in operating speeds of 1200 rpm for the Denver cell and 1400 rpm for the Leeds cell. The cells performed similarly at two coarser-sized fractions. However, some deviations were observed in the finer particle size range. The -25 μm (fine) fraction initially achieved a recovery of only 15%. An additional reagent dosage was required to enhance the recovery of this fraction significantly. These findings highlighted the influence of particle size on flotation recovery. For all experiments, the Denver laboratory flotation cell outperformed (defined by higher recovery) the Leeds device, while still operating at a lower impeller speed. This advantage can be attributed to its impeller-stator design and air dispersion features, effectively overcoming slurry resistance and resulting in superior flotation performance compared to the Leeds cell.

May 27, 2025

By F. Lanaro, K. Röshoff, R. Christiansson, L. Jing

This paper presents the results of a project for developing a methodology for empirically determining some of the mechanical properties of the rock mass at the Äspö Hard Rock Laboratory, Southern Sweden. Using the equations available in the literature, the deformation modulus, friction angle, cohesion and unconfined compressive strength of the rock mass were estimated. A comparison of the results using different classification methods (Q, RMR, GSI, RMi, Ramamurthy’s) was made to estimate the range of variations in the mechanical properties with the considerations of: i) the quality/quantity of the geological data; ii) the technique for partitioning of the rock mass into homogeneous domains; iii) the sensitivity and subjectivity of the empirical methods; and iv) the need for validating the empirical methods against a test case. Cet article présente les résultats d’un projet visant à établir une méthodologie, pour déterminer, de façon empirique, les propriétés mécaniques de la masse rocheuse. En utilisant les corrélations disponibles dans la littérature, quelques-unes des propriétés de la masse rocheuse ont pu être déterminées (module de déformation, angle de friction, cohésion, force de compression illimitée). Une comparaison des résultats obtenus par différentes méthodes (Q, RMR, GSI, RMi, de Ramamurthy) a permis d’établir une échelle de variations des propriétés mécaniques et de formuler une série de recommandations concernant : i) la qualité/quantité des données géologiques ; ii) la technique de partition de la masse rocheuse dans des domaines homogènes ; iii) la sensibilité et la subjectivité des méthodes empiriques ; iv) la nécessité de valider les méthodes empiriques à l’aide de nouvelles études de cas. Dieses Paper präsentiert die Ergebnisse eines Projekts mit dem Ziel, eine Methodik für die empirische Festhellung von mechanischen Eigenschaften im Gesteinmassiv zu etablieren. Durch Verwendung der in der Literatur zugänglichen Korrelationen, wurden einige Eigenschaften des Gesteinmassivs festgestellt (Entstellungsmodul, Reibungswinkel, Kohäsion, unbeschränkte Kompressionsstärke). Ein Vergleich der Ergebnisse unterschiedlicher Methoden (Q, RMR, GSI, RMi, Ramamurthy’s) wurde durchgeführt und dies erlaubte die Feststellung der Variationsskala von den mechanischen Eigenschaften, sowie eine Reihe Empfehlungen für: i) Qualität/Quantität der geologischen Dateien; ii) die Technik für Teilung des Gesteinmassivs in homogene Domäne; iii)die Empfindlichkeit und Subjektivität der empirischen Methoden; iv) das Bedarf die empirische Methoden gegen neue Fallgeschichten zu validieren.

Jan 1, 2003

By M. Wong-Kian, L. A. Cornish, A. van Bennekom

Samples of four different satellite materials were prepared by either hot isostatic pressing (HIP) of the powder or tungsten inert-gas welding of rod onto a 316 L stainless-steel substrate. The samples were subjected to a series of comparative erosion corrosion tests, and generally the Hipped samples experienced between 13 and 24 per cent less loss in mass than the equivalent welded alloys. Resistance to erosion corrosion increased with increasing carbon, chromium, and tungsten contents. Metallographic studies indicated the differences in carbide content between the different satellite materials, and the differences in morphology between the Hipped and welded samples. Finer and more homogeneous microstructures were

Jan 1, 1995

By M. Ayhan

Drums of a modern longwall shearer are manufactured to include various constructional features conveying extracted material onto the face conveyor as efficiently as possible. Designing a drum with a conical shell or with reduced vane length, consequently with a stepper vane angle, is the most widely employed method in an attempt to increase loading efficiency. This study compares loading performances of two such drums, one having a conical shell with modified loading vanes, the other with a cylindrical shell with reduced vane length. Firstly, the loading performances of drums are predicted and the maximum haulage rate attainable with the drums are calculated. Then the performances of drum are compared by long-term comprehensive underground trials with coal shearers under similar conditions during the production operation of Park Termik Cayirhan coalmine in Turkey. Although higher loading performance is predicted for cylindrical drums, the in situ trials point out that Globoid drums have a slightly higher loading performance than cylindrical drums. Furthermore, the relationship between operational variables, i.e. extraction height, sumping depth, haulage rate and in situ loading performance, were investigated statistically on the basis of data gathered during the underground trials. Keywords: longwall mining, shearer drums, loading performance.

Jan 1, 2006

By J. W. van der Merwe, A. Palazzo

"Owing to the corrosiveness of the untreated brackish cooling water typically used for steel mills (and other environments), it is important to treat the water and monitor corrosion in such systems. Generally, corrosion rates are monitored with corrosion probes inserted into a pipeline or vessel. This has been standard practice for many years, and is widely accepted in industry. Typically, two kinds of probes are used - electrical resistance and linear polarization resistance (LPR) probes.In this study, the effectiveness and accuracy of the LPR technique was evaluated by comparing the electrochemical measurements with the results of mass loss tests using corrosion coupons. The corrosivity of the environment, a synthetic brackish water, was varied by varying the calcium hardness and alkalinity, and to simulate actual plant conditions temperatures of 35°C and 45°C were used. In addition to the corrosion rate measurements, the iron concentration was measured, as well as the imbalance from the probe.The corrosion rates obtained by LPR were from 57% lower to 385%higher than those from the immersion tests. Most probe measurements were higher than the immersion results, and 50% of the probe results were50% or more higher than the immersion results. The best correspondence between the two methods was obtained at low calcium levels, except for one measurement that was 93% higher than the coupon results. There was no clear correlation between parameters such as temperature and total alkalinity and the difference between the results. It would therefore appear that LPR measurements can differ significantly from immersion results, and LPR results should therefore be used with caution in industrial applications."

Jan 1, 2015

By R. Castro, R. Gómez, F. Betancourt, M. Moncada

In block cave mining, rock fragmentation is a key parameter that influences the production level design and mine planning. Fragmentation occurs mainly by natural breakage during the caving process and in the draw column. The breakage that occurs within the column is known as secondary fragmentation. Secondary fragmentation has been successfully described using the block caving comminution model, which replicates the fragmentation mechanics between particles under drawn and vertical loads in a draw column. This model is based on a kinetic and population balance approach, in which non-normalized and normalized assumptions can be used depending on material and comminution system behaviour. In this paper, the non-normalized and normalized approaches are applied and compared to laboratory data to determine which assumption should be used for secondary breakage in block caving. Approaches are compared graphically, with the mean square error and the Fisher test with a false-rejection probability of 0.05. Based on a statistical analysis, the results show that the normalized model can be applied to all the rock types tested.

Nov 1, 2021

By L. Forbes, G. Forbes, J. Wang

Bubble size measurement is a vital part of flotation system analysis and diagnostics. Over the years, a great many different bubble size analysis tools have been developed. However, all of them rely on ex-situ measurement and in-pulp sampling techniques. This paper evaluates the Mettler Toledo ParticleView™ Measurement probe as a novel method for in-situ bubble size measurement. This device is then compared to the conventional Anglo Platinum Bubble Sizer (StoneThree). It was found that the in-situ bubble size analysis technology appears to be a more user-friendly and reliable option for determining bubble size in flotation. However, the current instrument design is not suited to industrial applications. Keywords: Bubble size measurement, bubble coalescence, PVM probe

Jan 1, 2020

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007