Search Documents

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

By B. Elevli

This paper deals with the selection of alternative accesses to a podiform chromite orebody in Turkey. The most important alternatives studied in a related project have been stated as a new vertical shaft and a ramp system. The comparison of these alternatives have been carried out on the basis of total investment costs, ore transport unit cost and net present value (NPV) of overall project for various depth. The results show that up to the depth of 700 m, the total investment cost and NPV favours the ramp access while unit ore transport cost make the shaft access preferable.

Jan 1, 2002

By J. H. Viljoen, N. B. Strydom, J. S. Greyson, C. H. Van Graan

SYNOPSIS Bad eyesight and poor illumination can contribute to the occurrence of accidents in mines. As one part of a study of this problem, surveys of light intensities have been conducted in 19 gold mines. On 17 of the mines the surveys were on one underground level only, whilst in two of the mines more intensive surveys were conducted by measuring light intensities in all areas to determine any inter-mine variations between the levels of illumination. Readings of light intensity were taken underground at stations, tips, winches, stopes, conveyor belts, waiting places, pump stations, fitters' and boilermakers' workshops, ambulance rooms and in haulages. It is concluded that the average levels of illumination in South African gold mines are comparable with those reported in the literature for mines elsewhere. Standardisation of lighting conditions underground could eliminate inter- and intra-mine variation in illumination levels where they occur. A guide to mine illumination practice would assist such standardisation, and help increase the levels and effectiveness of illumination in mines. Some suggestions are made in this latter connection.

By J. H. Viljoen, C. H. Graan, N. B. Strydom, J. S. Greyson

M J Martinson (Fellow) There is everywhere a lamentable dearth of quantitative information on occupational factors affecting the health and safety of mineworkers, and as the authors point out in their introduction underground lighting is one of the factors which has received little attention in South Africa prior to this welcome paper. Since the authors are to some extent pioneering, it is perhaps inevitable that the paper should raise more questions than it answers, but nevertheless it provides a provisional yardstick against which the need for, and success of, remedial action may be judged. Before commenting in detail on a few aspects of the paper it may be worthwhile to summarize the statutory provisions relating to underground lighting, contained in Chapter 15 of the Regulations promulgated in terms of the Mines and Works Act 27 of 1956. Chapter 15 is entitled `Lighting, Safety Lamps and Contraband', but in the context of the present paper only four simple regulations need be noted: firstly, no person shall work or travel in an unilluminated part of a mine unless he carries a light ; secondly, adequate stationary lights shall be provided at stations and certain other localities in shafts, winzes and places used for winding; thirdly, mechanically propelled conveyances shall be provided with an effective bright light shining in the direction of travel; and fourthly, moving machinery to which personnel have access shall be illuminated so as to be clearly visible. In all four regulations the standard of lighting to be provided is wholly subjective, and under these circumstances the wide inter- and intra-mine variations in light intensity disclosed by the study are hardly unexpected. Nevertheless the data presented in the authors' Table I raise three points (1) Is there any evidence that the 19 mines visited during the survey are representative of the 45-50 large gold mines in South Africa, or that the shafts selected are representative of the respective mines? Mine managers would scarcely be human were they not to offer better lit working places for the survey; perhaps the use of a scaling factor (e.g. tonnes or transit mineworkers per shift, kilowatts, etc.) for each working place might have helped to put the figures in perspective. (2) Looking at two of the more numerous - and probably important - of the ten working places included in the survey, i.e. stations and tips, one is struck by the marked. skewness of both intensity distributions (with higher frequencies at the lower intensities) and the abrupt cut-off in both cases just short of pitch darkness. Thus, of the 45 meaned readings recorded at 26 tips no less than 19 fall in the lowest range of 0,1-0,9 1m/ft2, with but one tip in total darkness; of 46 readings on 26 stations, 7 fall in the lowest range and none is in total dark-'1 ness. Although a light with an intensity in the range 0,1-0,9 1m/ft2 may satisfy the regulations, it is certainly arguable that in some situations it may be safer to have no light at all. (3) In view of the skewness referred to above, one wonders how meaningful are the `total average light intensities for (the gold mining) industry' quoted in Table I, which the authors compare with illumina¬tion levels found in other countries. Looking at tips again, one notes that 34 out of 45 meaned intensity readings fall below the `total average' for tips, and only 10 exceed it. From this it may be concluded that a few well-lit working places included in a `total average' may conceal a plethora in Stygian gloom. In their discussion the authors make fleeting reference to the effect of underground lighting on productivity and accident rates, without however quoting any South African experience in this regard. Intuitively it seems highly likely that better lighting (in the widest sense) would improve productivity and reduce accidents, and of course it is in these areas that the mining industry might seek economic justification for providing better lighting. It is all the more regrettable therefore that these factors were not studied simultaneously with the present investigation, especially at the Psychological Division of the Human Sciences Laboratory has recently published a study on underground accidents in the gold mining industry without making any reference whatsoever to lighting as a causal factor. In the event neither of the two studies enables us to make an economic appreciation of the situation, and this seems to be a classic example of a situation where some dovetailing of research effort would have greatly increased the useful return. On the effect of lighting on accidents, it may be noted that in 1939 Mickel presented some very interesting statistics to the Mine Managers Association of the Transvaal2, on the improvement in accident rates which followed the random issue of electric cap lamps to native mineworkers in the Hercules Section of E.R.P.M. the previous year. Based on a 12 month trial period in which 250 000 shifts were worked with carbide lamps and (contemporaneously) 307 000 shifts with cap lamps, the incidence of major accidents (at least one day in hospital among men using carbide lamps was 1,15 accidents per 1000 shifts, while the incidence of minor accidents (requiring dressing only) was 11,52 per 1 000 shifts. The corresponding figures for men using cap lamps were 0,79 and 7,31 accidents per 1 000 shifts respectively, representing a reduction of over 30 per cent in both major and minor accidents. While these figures are obviously dated - only men using cap lamps were issued with hard hats, for instance - they do indicate a need for similar research today.

Jan 1, 1971

By D. Borman

The location of underground positions in mines has usually fallen to their survey department's. Their usual tasks include: ? installation of a high-precision peg network like the National Survey grid as beacons ? offset measurements to the sidewalls, and sometimes hangingwall and footwalls, of development tunnels and excavations ? offsetting of stoping panels for the calculation of face ? advance and the square meterage of area removed. Other departments build their observations into the plans produced by the surveyors. If more precision is required, they ask the surveyors to `elevate' their points with a theodolite. Apart from the survey peg network and `elevations' these measurements are usually planer measurements suitable for producing plans, sections and projection sheets. When the only representation medium was a sheet of paper or transparency, this was perfectly suitable. However the development of CAD models of the workings has changed all this. Full 3D representation is not properly catered for in the tool sets in current use, and needless hours are spent converting analogue-type observations into digital form. The basic survey models need to be augmented by the observations of other disciplines that are also required to locate positions underground. These include: ? the need for geologists to plott their mapping and ? borehole logs into 3D space ? the need for samplers to position their sample points accurately because the geostatistical models are biased and inaccurate ? the need for stoping width recorders to position their thickness observations to prevent errant evaluation and bonuses ? the need for rock engineers to place their mappings into 3D to build true geotechnical models to manage geotechnical stresses ? the need for production officials to receive updated face ? positions during the month so that they can manage the ? production and utilize their resources properly. This paper covers a new method of positioning profiling points to a suitable degree of accuracy. I believe the method is sufficiently simple and cheap for all to use. Historical methods Platinum and gold orebodies, especially in South Africa, are generally narrow tabular deposits. This made them suitable for depicting on a 2D medium like paper. The determination of stoping or face widths was not a problem, as the ore is removed in a single stoping process. Such 2D representations could be easily positioned using tape offsetting between survey pegs or points tied in from survey pegs. Problems of dip were handled by using 'Stope Sheets' which chose a best fit projection for the whole area depicted or by using true dip section sheets for inclined tunnels. Rolling reef and potholes were the common areas of difficulty. Most mines now model their orebody and plan the extraction in computer graphics. This means that the representation of the current workings has to change to support this trend. It now becomes a truly 3D problem. Mining officials find it inconvenient to have their actual workings in single-line depictions while their orebody is depicted with top and bottom contacts and the planned tunnels in 3D shapes. Geological models which form the basis for the resource model and planning process are often out of date, as the updating process is slow. The geological mapping has to be plotted onto sections and plans. These are then digitized into graphics by a draughtsman and checked by the geologist. Only then does the interpretation and model update take place. Potential methods to create 3D 'Actuals' Global positioning systems (GPS) Surface mines have been blessed by the advent of GPS technology. These simple-to-operate pieces of equipment and compatible software make it possible for all types of mine employees to locate themselves, and therefore to locate their observations. GPS are often inexpensive and give an acceptable degree of accuracy. Only in deep pits or close to the highwalls are observations hindered. Such technology cannot however, work underground. Ground penetrating radar (GPR) GPR is reported to be very useful for estimating the positions of potholes and faults. However it is still considered as providing an estimate, not a definite measurement. GPR is good for seeing into solid rock, not into open spaces. Inertia reading devices Experiments with inertia reading devices have been conducted on the mines. They were the forerunners of GPS for military guidance systems, and were even used for city navigation in the early 70s. They do however work best with heavy or fast-spinning gyros. Anglogold Ashanti's attempt to use them were discontinued in the mid-90s when the developers asked for an additional few million rand for a device that would weigh more than 12 kg and have a limited operational life.

Jan 1, 2006

By M. Åstrand, M. Johansson

"Advanced planning and automation are increasingly important in modern mines. Sophisticated methods for long-term mine planning are often used, and the advent of autonomous machines makes the actual operation more predictable. However, the interface between these two timescales, i.e. the scheduling of the mobile production fleet, often limits the ability to operate mines at maximum profitability. We show how scheduling the production fleet in an underground mine can be modelled as a flow shop. A flow shop is a general abstract process formulation that captures the key properties of a scheduling problem without going into specific details. Thus, the flow shop enables mine scheduling to reap the benefits of scheduling research from other industries. We review recent results from the mining community and the flow shop community, and introduce scheduling methods used in these two fields. This work aims at providing value to researchers from the mining community who want to leverage their skill set, as well as to theoretical researchers by presenting the mining process as a potential application area. Lastly, we discuss the results, and outline some future challenges and opportunities facing the industry. IntroductionThe margins in underground mining are constantly under pressure since costs increase as the mine becomes deeper. One major component influencing the operational performance, and thus the profitability of an underground mine, is how the mobile machinery and staff are coordinated. Today, the coordination of the underground fleet, i.e. scheduling of the machines, is mostly done manually, with methods that are stretched to their limit and with no guarantees on performance. According to a survey of more than 200 high-level executives in mining companies around the world (Mincom, 2011), the top challenge for modern mines is to maximize production effectiveness, rather than improving the reliability of individual items of equipment. This highlights the importance of coordination on a system level.The effectiveness of mine production can be increased by introducing supportive algorithms in the scheduling process. These algorithms enable mines to construct optimized schedules with respect to custom metrics. Additionally, manual scheduling is a tedious and error-prone task where the performance is heavily dependent on the scheduler. To reduce the staff dependency, supportive algorithms can help to achieve more uniform outcomes, resulting in a more predictable process. In turn, this increases the transparency of the mining process through the entire production chain. It is worth noting that automatic scheduling has proved beneficial in many other industries, such as chemicals and metals (Floudas and Lin, 2004; Tang et al., 2001)."

Dec 1, 2018

By N. Gatelier, T. You, J. C. Kandel

ABSTRACT: Underground hydrocarbons storage is a very specific domain for the designer. He is usually free to adjust the section, shape and layout to cope with the geological and geotechnical conditions. This paper presents a panorama of the geotechnical design of mined underground storage caverns, then lists a number of uncommon features encountered in a storage excavated in Sydney, Australia, the Elgas LPG project that had to face major non-isotropic conditions with numerous local variations, impacting on the achievement of the design profiles. Changes in geotechnical design methodology and practice are examined through this project, now in operation, which will have lasted altogether almost ten years. KEY WORDS: underground storage, geotechnical engineering, stability, methodology, design. ZUSAMMENFASSUNG: Die untertaegige Speicherung von Kohlenwasserstoffen unterliegt in der Planung sehr spezifischen Bedingungen. Der planende Ingenieur hat bei der Dimensionierung und Formgebung der Speicherhohlraeume gewisse Freiheiten, muss jedoch vorgefundene geologische und geotechnische Bedingungen beruecksichtigen. Der vorliegende Beitrag gibt zunaechst einen allgemeinen Ueberblick ueber die geotechnische Planung von bergmaennisch aufgefahrenen Speicherhhohlraeumen. Darueber hinaus werden Besonderheiten betrachtet, mit denen das Elgas LPG-Speicherprojekt in einer bergmaennisch aufgefahrenen Kaverne in Sydney, Australien konfrontiert war. Hierbei ging es um die Beruecksichtigung anisotroper Bedingungen mit zusaetzlichen Heterogenitaeten im Gestein und den daraus erwachsenden Schwierigkeiten, die geplante Hohlraumform zu verwirklichen. Ueber einen Zeitraum von fast 10 Jahren, in denen das jetzt in Betrieb befindliche Projekt unterschiedliche Betriebsphasen durchlaufen hat, wurden verschiedene geotechnische Entwurfsverfahren auf ihre Anwendbarkeit geprueft. SCHLUESSELWOERTER: Untergrundspeicherung, Geotechnik, Stabilitaet, Entwurfsverfahren, Planung. RESUME : Le stockage souterrain d’hydrocarbures est un domaine très spécifique pour le concepteur, car celui-ci dispose d'une large liberté pour adapter les sections, les formes et les implantations aux conditions géologiques et géotechniques de l’environnement choisi. Après un panorama de la conception géotechnique des stockages souterrains d’hydrocarbures par la méthode dite des cavités minées, l’accent sera mis sur un certain nombre de particularités rencontrées lors du projet de stockage de GPL de Elgas à Sydney en Australie, creusé dans de très fortes conditions d’anisotropie du massif rocheux, avec de nombreuses variations locales et toutes les implications que cela peut avoir sur le maintien des formes. L’évolution des approches méthodologiques géotechniques durant la dizaine d'années de développement de ce projet depuis les premières études jusqu'à l'exploitation actuelle est également présentée. MOTS-CLEFS : stockage souterrain, géotechnique, stabilité, méthode, conception.

Jan 1, 2003

By T. Bednarski, L. Thomas, G. Banza, D. Muteba, P. Cole, M. Soderstrom

"In copper solvent extraction, aqueous-in-organic entrainment results in the carry-over of unwanted species into the electrowinning process with negative cost implications. The need to bleed is increased and the purity of the copper cathode is potentially compromised, depending on the impurities being transferred (Cl, NO3, Fe, Mn). In some cases, entrainment results in elevated levels of manganese in the electrolyte which can cause oxidative conditions to develop and degradation of the organic phase. Degraded organic phase detrimentally affects the physical performance of the copper solvent extraction process, contributing to even higher aqueous-in-organic entrainment. Aqueous entrainment may be minimized through good operating practices and maintenance of the organic quality, but the accurate measurement of entrainment remains a challenge. This paper presents coalescing devices designed to provide more exact measurements of aqueous-in-organic entrainment. IntroductionMany copper solvent extraction (SX) plants experience high aqueous-in-organic (A-in-O) entrainments but are unaware of the extent of the problem because entrainment is often not measured. Aqueous entrainment results in the carry-over of unwanted species into the electrowinning (EW) process and the need to bleed to maintain acceptable concentrations in the electrolyte. The costs associated with the bleed are exacerbated in copper plants where aqueous entrainment levels are high. Other than these direct costs, there are operational consequences of the build-up of certain species in the EW circuit that can have deleterious effects on plant performance.Minimizing aqueous entrainment in operating plants requires an understanding of the factors that affect entrainment levels. Both chemical and operational influences are discussed in this paper. The difficulty of obtaining a representative sample makes it challenging to obtain an accurate measure of aqueous entrainment from a continuous process like SX. Coalescing devices used to get a more precise measurement of A-in-O entrainment are useful to complete mass balances around the SX circuits. Alternatively, mass balances can be used to estimate aqueous entrainments and are helpful as a tool to troubleshoot operations with a view to improving plant performance."

Jan 1, 2016

By J. Petersen, M. Reuter, E. Asselin, M. Becker, N. Uys

In order to meet society’s ever-increasing demand for metals and address the numerous technical, economic and environmental challenges within the current mining context, a holistic approach to process design, which is grounded in mineralogy, is needed. This would ensure that the impact of varying process mineralogy (and associated chemistry) on technical considerations and the associated economic implications and environmental consequences are taken into account upfront. This investigation focuses on the commodity zinc due to its strategic value coupled with limited resource availability and the wide variety of substantially different process technologies in existence. As the most commonly processed zinc ores contain zinc sulphides, the mineralogy/chemistry of these ores and their associated process routes will be discussed. The findings have been generated through the analysis of two case studies, Teck’s Trail Operations (British Columbia, Canada) and Hudbay Minerals’ Flin Flon Operations (Manitoba, Canada). The flotation of zinc sulphide ores to produce concentrates with varying mineralogy, represents the starting point for both case studies. The hydrometallurgical process routes for the further refining of zinc and other valuable metals include roast-leach-electrowinning (RLE), and zinc pressure leaching (ZPL). The effect of process route choices on primary metal recovery (Zn), coproduction of other base metals (Cu, Pb), potential for other valuable metal production (Ag, Au) including less well known, but increasingly important trace elements (In, Ge), and the production of other by-products (H2SO4, S0) are discussed. The economic and environmental implications of these aspects will also be considered. It is concluded that a quantitative modelling approach must be taken where waste management is integrated into process system design and simulation as a key unit operation. Keywords: Zinc Sulphide Processing; Design Decisions; Mineralogy

Jan 1, 2020

Heavy mineral deposits are becoming more complex in terms of their compositional variation, particle mineralogy and size distributions, and present challenges for the operation of separation equipment to achieve the required grades and recoveries. Changes in equipment design and concepts potentially provide new opportunities for the beneficiation of heavy mineral sands deposits. The development of a framework for the fundamental understanding of separator performance issues is a first step to develop new machines. This paper will present a first step analysis of electro-static and magnetic separation machines with their application to real separation scenarios.

Jan 1, 2010

By B. McFadzean, N. Patterson, M. Becker, S. Geldenhuys

The retreatment of secondary tailings for platinum group metals recovery presents a range of potential challenges, which vary depending on the nature of the original ore and the type of pretreatment it was subjected to. These challenges include the prevalence of ultrafine particles, which promote slimes coatings on valuable minerals, hinder bubble-particle attachment, increase pulp viscosity, and lead to higher gangue entrainment; surface oxidation of minerals, which alters their floatability; and the presence of deleterious gangue minerals and residual platinum group metal species that are inherently difficult to recover by flotation. This study compares the batch flotation performance across a range of tailings samples from the eastern and western limbs of the Bushveld Complex. A complementary mineralogical analysis was conducted to gain deeper insights into mineral behaviour. The paper evaluates these findings to identify the key factors contributing to poor platinum group metal performance.

Mar 6, 2026

By R. W. Ottermann, N. D. L. Burger, A. J. von Wielligh, P. R. de Wet, J. L. Steyn

Underwind and overwind protection system concepts for mine hoist shafts were developed in conjunction with and for the Safety in Mines Research Advisory Committee (SIMRAC). End-of-wind operation of mine hoists is the most hazardous aspect of mine hoisting, carrying the highest risk of loss of life, injuries to workers and loss of production. Systems operating mechanically and with local actuation were developed. This was done in order to remove the increased risk associated with dependency on remote or external energy and information supply associated with most existing protection systems. The proposed underwind protection system concept absorbs the energy of motion of a conveyance overrunning the design lower limit of travel by drawing a metal strip through a set of rollers. This action causes dynamic cyclic plastic bending of the strip material that converts the kinetic and potential energy of the conveyance into strain energy of the metal. In the concept design a pair of cable slings attached to the strips catch the overrunning conveyance and transfer the retardation force. The proposed overwind protection system concept absorbs the energy of motion of a conveyance overrunning the design upper limit of travel by early detaching of the conveyance from the hoist cable. This detaching is carried out via an additional humble hook activation mechanism fitted at a sufficient height below the spectacle plate to allow the conveyance to retard to standstill under gravity before it would crash into the spectacle plate. The conveyance so brought to rest is prevented from falling by means of jack catches on the conveyance interacting with a rack (toothed profile) fitted on the guide rails in the retardation zone. Scale models (1:10 scale) of both protection systems were designed for conformance with established retardation standards. The retardation standards were limited by the requirement of passenger safety in retarding cages. The models were then built and tested in a 1:10 scale shaft model. Retardation performance close to the required levels was achieved. The retardation distance required should allow such systems to be retrofitted to most existing shafts. Given the simplicity and robustness of the designs

Jan 1, 2003

By N. D. L. Burger

Underwind and overwind protection system concepts for mine hoist shafts were developed in conjunction with and for the Safety in Mines Research Advisory Committee (SIMRAC). End-of-wind operation of mine hoists is the most hazardous aspect of mine hoisting, carrying the highest risk of loss of life, injuries to workers and loss of production. Systems operating mechanically and with local actuation were developed. This was done in order to remove the increased risk associated with dependency on remote or external energy and information supply associated with most existing protection systems. The proposed underwind protection system concept absorbs the energy of motion of a conveyance overrunning the design lower limit of travel by drawing a metal strip through a set of rollers. This action causes dynamic cyclic plastic bending of the strip material that converts the kinetic and potential energy of the conveyance into strain energy of the metal. In the concept design a pair of steel wire rope slings attached to the strips catch the overrunning conveyance and transfer the retardation force. The proposed overwind protection system concept absorbs the energy of motion of a conveyance overrunning the design upper limit of travel by early detaching of the conveyance from the hoist rope. This detaching is carried out via an additional detaching hook activation mechanism fitted at a sufficient height below the spectacle plate to allow the conveyance to retard to standstill under gravity before it would crash into the spectacle plate. The conveyance so brought to rest is prevented from falling by means of jack catches on the conveyance interacting with a rack (toothed profile) fitted on the guide rails in the retardation zone. Scale models (1:10 scale) of both protection systems were designed to conform to established retardation standards. The retardation standards were limited by the requirement of passenger safety in retarding cages. The models were then built and tested in a1:10 scale shaft model. Retardation performance close to the required levels was achieved. The retardation distance required should allow such systems to be retrofitted in most existing shafts. Given the simplicity and robustness of the designs, further development was recommended because of their enhanced self-sufficiency and reduced risk of malfunction. Keywords: underwind, overwind, deceleration, mineshafts, hoisting.

Jan 1, 2004

By A. Esterhuizen

Since 2005 Two Rivers Platinum Mine has set out on an initiative to actively monitor and control ground conditions on a daily basis, by making use of borehole cameras and pro-actively amending the support and mining strategies based on day-to-day observations of the hangingwall conditions. Today the borehole camera observations form part of the Rock Engineering Department?s daily function, and the size and frequency of falls of ground and ensuing accident rates have been drastically reduced since implementation of the system. The Two Rivers Platinum fall-of-ground management system aims to support 100% of the possible fallout thickness, based on ongoing data gathering and interpretation, thereby ensuring safety and limiting support cost.

Jan 1, 2014

By R. J. Fruehan

Slags have many useful functions in iron and steel making. In particular, slags are used to remove impurities such as sulphur, phosphorus and inclusions from the metal, and a large amount of research has been done in this area. Slags also insulate the metal thermally and form reactions with the atmosphere such as reoxidation and nitrogen pick-up. However, slags serve other more unique functions, several of which are reviewed in this paper. The role of slags in new iron smelting processes with regards to reduction of ore and gaseous desulphurization are discussed. In iron smelting processes, much of the reduction occurs by the reaction of carbon in the char and the metal suspended in the slag with iron oxide dissolved in slags. The slags also react with the gas resulting in sulphur removal from the process. The mechanisms of these reactions and pilot plant data for these processes are given in this paper. Slag formation within ferrous burden materials affects the cohesive zone and the performance of the blast furnace. Recent theoretical and experimental findings on this topic are presented. In the electric arc furnace, foamed slags are used to allow for higher power operation and productivity. Of particular interest, foaming in stainless steel production is more difficult than for normal steels. The foam index, or the ability of the slag to foam, for stainless steelmaking is similar to that for carbon steelmaking slags. The poor foaming is due to the lack of gas generation for the foam. Methods to increase foaming in stainless steelmaking are discussed.

Jan 1, 2004

By Dave Deglon, Andrévan der Westhuizen

Objectives ?Survey typical Met Accounting streams at the Zincor refinery ?Determine Precision in Metal Conc?s Measurements for Monthly Met Balance ?Determine the Components of Variance in these Met Acc Values (Sampling, Preparation, Analyses) ??Common plant practice? should be mirrored even though not always in perfect agreement with ?laid down procedures? or ?good practice? ?Mass Measurement and Inventory Measurement was considered in less detail ?not reported here

Jan 1, 2005

In Chapter 1 we mentioned that up to three components are considered to represent the variability of regionalized variables : a deterministic component, a correlated component, and a random component. In Chapter 2 we considered some of the models based on the assumption of randomly distributed values: the random component was assumed to be the only one present. In Chapters 3 to 11, more general but also more complex models were described, based on the assumption that the values were correlated with the possible presence of random noise. In this chapter we introduce a model used to analyse non- stationary data, for which a deterministic component (or drift) must be assumed. This model will be used for estimation purposes, and the corresponding optimal linear estimation procedure is known as universal kriging. The theory of universal kriging is much more complex than the theory of kriging. Fortunately, in the majority of mine valuation problems the drift can be ignored and the simpler form of kriging can be used.

Jan 1, 1978

By W. P. Nel

The introduction of the Higher Education Qualifications Framework (HEQF) and the updated Higher Education Qualifications Sub-Framework (HEQSF) has caused many South African university departments to rethink their programme qualification mixes (PQMs). In addition to the requirements stated in the HEQSF, a number of other factors have to be taken into consideration by a university department. These factors include, for example, the standards generated by the Engineering Standards Generating Body (ESGB) and subsequently approved by the Engineering Council of SA (ECSA) and the need to prepare students for various categories of professional registration with ECSA. This means that a university department has to choose the correct mix of Learning Programmes (LPs) from the HEQSF menu (which consists of 13 types of LPs). Preparing students for ECSA registration is aligned with the mission of universities, which is to teach and undertake research. However, research and the LPs associated with research go beyond the requirements for current ECSA registration. Assuming that universities offering engineering LPs would elect to prepare students for both ECSA registration and teach them to produce research outputs, which is mostly done at Master and Doctorate levels (NQF Levels 9 and 10), then it follows that academics are more interested in NQF Level 5 to 10 pathways (abbreviated as ?L5-10?) rather than the shorter pathways required towards professional registration. (For example, ECSA requires an NQF L5-L7 pathway for registration as a candidate professional technologist. This specific pathway may consist, for example, of two LPs, namely the 360-credit Diploma and the Advanced Diploma.) A L5-L10 pathway is a combination of LPs that will prepare the learner with a NSC (or equivalent qualification at level 4) to Doctoral level (level 10). Universities may choose at least four major pathways from the HEQSF menu in order to educate and develop students from NQF Level 5 to 10. However, various pathways towards registration in the category of candidate with ECSA are also embedded into these four NQF L5-L10 pathways, where each consist of a unique combination of LPs. Each of these pathways has an opportunity cost, and economic reality means that smaller departments may have to choose between the four pathways. Of all the many factors involved in PQM decision-making, the focus of this paper is on the HEQSF requirements, ECSA standards, and ECSA registration and how these, together with the various qualifications and educational LPs provided for by the HEQSF may impact on the PQM decision taken by engineering departments and schools at South African universities. The proposed four NQF L5-L10 ?pathway tool? for PQM decision-making may be useful for pointing out the advantages, disadvantages, and applications of the various pathways and combinations of pathways. Rather than deciding from a menu of thirteen qualifications and associated LPs, this article proposes that decision-making be undertaken on the basis of a menu of four main articulated ?NQF L5-L10? pathways (which also include one or more of the ECSA?s pathways for professional registration). The proposed ?NQF L5-L10 pathway? tool is an attempt to move one step closer to the aim of achieving a structured decision-making approach for designing a PQM at departmental level.

Jan 1, 2014

By G. T. Lineberry, C. M. Baird, D. L. Silverstein

The University of Kentucky (UK), with an enrollment of 25,891 in fall 2002, is a comprehensive, public land-grant university located in the Bluegrass Region of Central Kentucky. As the State’s flagship university, UK has long been involved in distance education, first through traditional correspondence courses, followed by use of videotape and satellite delivery in the 1970s and1980s, but soon supplanted by use of interactive television (ITV) and on-line course delivery in the 1990s to date. Today, UK Distance Learning Programs annually administers approximately600 course sections, with services provided to over 5200 enrollees. Courses are offered via six media: interactive video, Internet, on-site, satellite, open-air and cable television, and videotape, with hybrid delivery becoming increasingly popular. The University of Kentucky College of Engineering experience with distance instruction prior to 1985 was limited to videotape non-credit offerings. The Department of Mining Engineering, a small department in terms of numbers of both faculty and students, was a University pioneer in distance education. The first University degree program offered in its entirety by distance delivery(initially by itinerant faculty) was the Master of Mining Engineering. Satellite delivery from Lexington to Cumberland, Kentucky, was a welcomed change of delivery mode in 1987–88,resulting in six hours less travel time for faculty each week. Shortly thereafter, other initiatives directed toward fulfilment of its land-grant mission were undertaken by the College. Use of satellite for course delivery rapidly declined due to limited interactivity, in favour of compressed video and on-site instruction. Classroom sites in the Kentucky Tele-Linking Network (KTLN) now number over 200. The Network links schools, colleges and universities, as well as public and private agencies throughout the State. The KTLN supports voice, video, and data transmission in a uniformly-equipped environment. Beginning in the early 1990s, transfer-critical pre-engineering courses were delivered from Lexington to Kentucky’s community colleges with the largest pre-engineering enrolments. Success was limited, but lessons learned were invaluable. In 1996, the University of Kentucky College of Engineering was asked by the Kentucky Council on Higher Education (the predecessor to the Council on Postsecondary Education) to expand engineering education in Kentucky, first by initiating cooperative B.Sc. degree programmes in Chemical Engineering and Mechanical Engineering on the campus of Paducah Community College (PCC), located 400 km from the UK campus in Lexington. The third partner in these programmes is Murray State University (MuSU), a public regional comprehensive university 80 km south of Paducah. The genesis of the new degree programmes, which were subjected to ABET review in October 2002, as well as a summary of the major accomplishments and challenges of the innovative programmes, will be offered. The limited use of distance technologies for course delivery in these B.Sc. degree programmes will be discussed. A ‘no-spin’ overview of other non-traditional distance-learning ventures within the College of Engineering will be chronicled, with an honest assessment of the motivation for these efforts and, where appropriate, their relative degree of success. Among these ventures are: a BScME and a Master of Engineering programme at Toyota Motor Manufacturing of Kentucky, Georgetown, Kentucky; course exchange in Chemical Engineering between the University of Kentucky and the University of Louisville; an ITV-based Master of Engineering programme for practicing engineers in Kentucky; proposed joint-degree programmes in Civil Engineering and Mechanical Engineering with Western Kentucky University; and a proposed part-time MScME programme in Paducah, Kentucky, with a start date of August 2002, threshold enrolment permitting. Keywords: distance learning, distance education.

Jan 1, 2003

By M. Pelser, J. Hagemann

"The Anglo American Platinum Rustenburg Base Metals Refiners (RBMR) is the largest producer of nickel cathode in South Africa. It treats slow-cooled matte to recover a platinum group metal-containing magnetic fraction for downstream processing and a nonmagnetic fraction to produce nickel and copper cathode, cobalt sulphate, and sodium sulphate. The refinery was recently expanded from 21 to 33 kt/a nickel. During the ramp-up phase, the sulphur removal section was found to be a constraint to throughput. Nickel hydroxide is precipitated from nickel spent electrolyte by addition of sodium hydroxide, and filtration of the nickel precipitate allows sulphur to be removed from the circuit as aqueous sodium sulphate in the filtrate. The filtration fluxes were found to be limiting the circuit’s capacity. An obvious solution would have been to install additional filtration capacity at significant capital cost and long lead times. RBMR chose rather to first initiate a collaborative project with Anglo American Technical Solutions to better understand the impact of process conditions on filtration characteristics and to evaluate whether the filtration flux could be increased by improving the quality of the nickel precipitate.A deeper understanding of nickel hydroxide precipitation chemistry and kinetics in the context of high nickel and sodium hydroxide concentrations was developed, guided by precipitation theory and confirmed by laboratory tests and plant observations. It was found that the filtration rate could be significantly improved by modifying the precipitate characteristics. A new precipitation process was engineered and retrofitted into the existing plant. Since start-up of the new precipitation system, the available capacity of the sulphur removal section has more than doubled, and control of the process has improved with the better agitation. This paper describes the theory and results used to design the new agitation system, as well as the impact of the change on capital investment, operability, and process efficiency."

Jan 1, 2016