Search Documents

This paper summarizes the results from a project aimed at adapting scroll centrifuges for application to the dewatering of flotation concentrates. The main impetus for the project was to reduce the high cost and footprint size of the technology currently used to dewater fine coal. The technical challenge was to enhance solids capture by incorporating a laser-cut screen into the design of the basket. The project has shown that a pilot-scale scroll centrifuge can be used to dewater froth concentrate. A number of different basket designs were tested, the best results being achieved with a basket comprising a laser-cut screen of aperture 70 µm. The best result on a sample of untreated flotation concentrate, which was taken from the open trough flotation cells at a coal preparation plant (CPP) in NSW was a solids recovery of 82 wt% at a product moisture of 24.3wt%. By comparison the best product achieved with a conventional wedge wire basket was a similar moisture content but solids recovery was only 64 wt%. This could only be achieved after the feed had been artificially thickened. Conditioning of the centrifuge feed with polymer flocculants led to an increase in recovery up to 88 wt% with a moisture content of ca 25 wt%. It is thought that optimizing additive selection and conditioning parameters, as well as screen aperture and open area, could improve performance still further. The results were obtained using centrifuging conditions (centrifugal force, feed solids, feed rate) in the pilot-scale machine which should be possible to translate into conventional designs of commercial scale machines, without downgrading solids throughputs. However only with full-scale trials will it be possible to establish this assertion with certainty.

Jan 1, 2001

By A. Schippers, S. Hedrich

Chalcopyrite represents the most important copper resource and is currently mainly exploited using pyrometallurgy. Bioleaching is an environmental-friendly and economic alternative to conventional mineral processing technologies. The technical feasibility of stirred tank reactor bioleaching of copper ore concentrates using acidophilic iron-/sulfur-oxidising bacteria is proven, however, often incomplete due to inefficient chalcopyrite dissolution. A decoupling of bacterial growth from bioleaching activity in one bioreactor by adjusting appropriate temperatures for both process steps allows for almost complete chalcopyrite dissolution. Separation of copper and recovery of other metals from the PLS was possible by implementation of different biological and chemical techniques. The Ferredox process has been proposed to treat limonitic laterite ores for cobalt and nickel recovery by means of anaerobic reductive dissolution with autotrophic, acidophilic bacteria. As a modification, aerobic reductive dissolution of laterites with acidophilic bacteria has shown economic and environmental advantages over anaerobic reductive dissolution. The reductive bioleaching technology has the potential to increase metal recovery in existing mines, and transform unexploited ores and limonite stockpiles into valuable resources. Keywords: Biomining, bioleaching, chalcopyrite, laterite, Ferredox process

Jan 1, 2020

By R. Trammell, O. Eterigho-Ikelegbe, S. O. Bada

In response to the enormous amounts of coal discard generated during coal mining and preparation, the development of an efficient and sustainable strategic use of this resource is essential. Furthermore, the rising urban population over the next decades is confronted with the depletion of quality raw materials for building components. To this end, this study reports new information on the morphology, water absorption, and flexural strength properties of ceramic composites produced from three different coal discards and polysiloxane pre-ceramic polymer (PCP) resin. In addition, test results relating to the continuous operating temperature, chemical resistance, and efflorescence potential of the composites are presented. The results show that the water absorption and flexural strength of the coal composites, up to 1.94% and 36.46 MPa respectively, exceed the requirements for ceramic and clay roof tiles. The continuous operating temperature of composites is found to be more thermally stable than conventional roofing tiles (concrete and ceramic) between ambient temperature and 600°C. In addition, the excellent chemical resistance of the composites (94.43%−99.98%) compared to conventional roofing tiles (67.82%−99.97%) eliminates the need for additional external coatings. The interesting results documented so far suggest that this technique could be used to produce low-temperature application building products such as bricks, panels, roofing tiles, etc. This new recycling technique offers an excellent opportunity to eliminate enormous volumes of coal discard and to advance the circular economy in the coal industry.

Aug 2, 2022

By G. L. Smith, B. Genc, V. Morar, U. Govender

This paper presents a novel holistic healthy human framework for C-suite executives and senior leaders in the minerals industry. The value-add of the framework centres around the integration of inner holistic health and interpersonal holistic health to support and enhance environment, social, and governance transformation, with a focus on the social enterprise. The framework unpacks key components of holistic health and their interlinkages to environment, social, governance, and stakeholder engagement. Insights were gleaned from interviews with 10 C-suite executives, each with over twenty years of experience in mining or business leadership. By applying the holistic healthy human framework, industry leaders can strengthen the social licence to operate and positively transform the industry's public image. Broader application to other sectors is underway.

Oct 2, 2025

By J. O. Roux

The Impala Platinum Limited Base Metals Refinery in Springs, South Africa, refines convertor matte containing base metals and PGM?s (platinum group metals) using a hydrometallurgical process. In addition to a PGM-rich concentrate that is further refined, the Base Metals Refinery produces nickel (in powder or briquette form), copper cathodes and cobalt powder. Five leaching stages are utilized to remove the base metals and impurities from the PGM concentrate. The project described in this paper involves a radical redesign of the second stage leach autoclave with the aim of reducing maintenance costs and downtime, increasing throughput and ensuring a safer working environment. The second stage leach process at the Base Metals Refinery, produces a PGM-rich residue through the extraction of copper and any remaining base metals from the first stage leach solid residue material. Leaching is performed in an autoclave operating at a pressure of 600 kPaG and a temperature of 140°C to 150°C. Concentrated H2SO4 is added to the feed to produce a solution with a free acid content between 10 and 30 g/L and a pH of less than 2. Oxygen is passed into the 1st and 2nd compartments of the autoclave. As a result of the aggressive, highly oxidizing conditions within the autoclave, the original design utilized a heavy wall carbon steel shell with lead lining and two layers of acid bricks. The bricks acted as a wear resistant material and ensured a low surface temperature at the skin of the lead lining, whereas the lead lining acted as a corrosion barrier to protect the steel shell. These brick lined autoclaves were heavy, maintenance intensive and prone to catastrophic failure. A radical autoclave redesign was needed to reduce the high costs of manufacturing, installation and operation. Finite element modelling was used to optimize the design and various high alloy materials were investigated for the application. Based on extensive test work, the carbon steel shell was replaced with duplex SAF 2205 stainless steel in the new design. The use of this highly corrosion resistant material, eliminates the need for the lead and brick linings and reduces the wall thickness requirements substantially, resulting in an increase in the available volume for the same external shell dimensions. The vessel is welded in circular sections to form an elongated, impermeable, cylindrical body, with several agitator nozzles and compartments. The first new duplex stainless steel unit has been in continuous operation for more than 24 months and its performance has exceeded the highest expectations. The design was so successful that a patent has been registered. The major benefits of the new stainless steel design include increased throughput, improved performance, less downtime and a safer working environment. Lead has been eliminated and replaced with a more environmentally safe material, and the total lifespan of the vessel has been extended. In addition, the autoclave project has made significant developments in advancing the field of welding and optimizing the integrity of welding quality standards in South Africa.

Jan 1, 2009

By A. E. Voigt

Iron ore samples representing the input and output of several jigging experiments were analysed to determine the effect of particle size, shape, and density on jigging performance. Traditionally, the manual measurement of the size and shape of individual particles is very tedious and prone to inaccuracies and inconsistencies. Using a novel multi-view imaging technique the 3-dimensional representations of each particle in the sample was determined. From this representation several size and shape measurements were extracted, and these were correlated with the individual particle density measurements. A rigorous investigation into the confidence associated with density and the size and shape features as a function of sample size was conducted, thus allowing the significance of correlations in the data to be determined. The jig?s performance was seen to be clearly sensitive to density and markedly so to particle size, while the results for shape indicated the need for continued work in the definition of particle shape.

Jan 1, 2012

By D. Grabowski, Z. Pokryszka

ABSTRACT: Some residential areas of the iron basin of Lorraine (in the North-East of France) are affected by noxious gas emissions (under oxygenated, carbon dioxide loaded and radon loaded gas mixtures). Site investigations showed that the gas flow was mainly due to natural thermal air circulation between old mines and the external atmosphere. The main hazards associated with this flow of gas and its potential accumulation in confined volumes within buildings are asphyxiation and intoxication. A further study is in progress in order to better understand the origin of the gas generation within the old iron mine workings. Following the first hypothesis, the carbon dioxide emission is mainly due to the specific hydro-geo-chemical process associating the pyrite oxidation with the acid dissolution of carbonates. KEY-WORDS : gas, emission, mine, flow, pyrite. ZUSAMMENFASSUNG: Einige Wohngebiete der Eisenmulde Lothringen (im Nordöst Frankreich) werden von Ausgasung gesundsheitsschädlichen sauerstoffarmen Mischungen, die mit Kohlendioxid und Radon beladen sind, betroffen. Untersuchungen am Ort haben gezeigt, wie diese Gasstroemung von natürlichem thermischen Luftumlauf zwischen den alten Bergwerken und der externen Atmosphäre ausgelöst wird. Erstickung und Vergiftung sind die wichtigste Risiken, die mit dieser Gasströmung und ihrer möglichen Speicherung in begrenzten Lokalen zusammenhängen. Eine weitere Untersuchung wird durchgefuehrt so dass man die Herkunft der Gaserzeugung in den alten Grubenräume besser versteht. Der ersten Hypothese folgend, Ausgasung von Kohlensäure liegt vor allem an dem hydro-geo-chemischen Prozess, der Pyritrösten mit der säuren Auflösung von Karbonate verbindet SCHLÜSSELWÖRTER: Gas, Ausgasung, Bergwerk, Strömung, Pyrit RESUME: Certaines agglomérations du bassin ferrifère lorrain (au Nord-Est de la France) sont affectées par des émanations de mélanges gazeux sous-oxygénés et chargés en certains gaz nocifs (dioxyde de carbone, radon…). Les investigations effectuées in situ ont montré que les écoulements gazeux à l’origine de ces émanations sont liées au phénomène de tirage naturel entre les anciens travaux miniers et la surface. Les principaux risques engendrés par ces émanations de gaz et son accumulation possible dans des endroits confinés sont l’asphyxie et l’intoxication. Une étude est en cours afin d’expliquer l’origine de la modification de l’air au sein des vieux travaux miniers. Les émissions de dioxyde de carbone seraient dues à des processus hydro-geo-chimiques associant l’oxydation de la pyrite et la dissolution de carbonates. MOTS CLES: gaz, émanation, mine, écoulement, pyrite.

Jan 1, 2003

By J. P. Hugo

Nuclear energy - its interactions with mining and metallurgy - PRESIDENTIAL ADDRESS given by J. P. Hugo Pr. Eng., B.Sc (Eng.) (Rand), Ph.D. (Sheffield) Energy is the life blood of the modern technological era in which we live and it was, I think, Benjamin Franklin who said that the manipulation of energy was the basis of all science and technology. This is perhaps an oversimplification, but there can be little doubt that our life today, and the improved standard of living we aspire to, are governed almost entirely by our ability to generate and manipulate energy. This ability has made it possible for Man - each specimen a feeble twentieth of a horsepower - to travel to the moon, to recover valuable minerals from the depths of the earth, to do arithmetic at unbelievable speed, to lessen the drudgery of manual labour. For these and virtually every aspect of our life we are dependent on energy from external sources. It is, therefore, not surprising that the per capita consumption of energy, and more particularly electricity, has become one of the most reliable criteria by which to measure the standard of living and technological advancement of a country.

By P. C. Carrasco

Knowing the origin of the relevant and irrelevant components of the nugget effect is essential to optimize the process under study. This paper describes the causes of the nugget effect and, its dependency on the sample support, sampling density, and on the QA/QC procedures. Several examples of natural and ?human? nugget effect are given. A method to estimate the magnitude of the relevant and irrelevant components is suggested. Finally, the economic consequences of misunderstanding the nugget effect are analysed.

Jan 1, 2010

Numbering of the Journal Because computer and library authorities prefer journal subscriptions to be based on the calendar year, and because the present numbering system of the Journal of the South African Institute of Mining and Metallurgy does not conform with the calendar year, it has been decided to change the numbering system of the Journal.

Jan 1, 1979

By S. Bradshaw, A. Mabentsela

"Physical and numerical modelling methods were followed to identify mechanism(s) for tundish slag entrainment in a bare tundish and one with a flow control device (FCD).The physical and numerical models made use of water and paraffin to model steel and slag respectively. Observations from the physical model showed that the steel-slag interface remains immobile in both cases. Entrained paraffin formed droplets approximately 1 mm in diameter. Results from both models (numerical and physical) showed that in both cases (bare and FCD case), areas of high entrained slag concentration exist near the inlet region. The entrained slag concentration decreases towards the tundish endwalls.Flow patterns and velocities tangential to the steel-slag interface from the numerical model showed that slag entrainment in both the bare tundish and tundish with a FCD possibly takes place via two mechanisms. First, the slag moves across the steel-slag interface via mass transfer; secondly small velocities tangential to the interface at depths greater than 10 mm below the interface carry the already ‘entrained’ slag into the bulk steel phase. These tangential flow patterns are dominant in the inlet region, hence the high concentration of entrained slag in this region. IntroductionThe tundish serves as the last metallurgical vessel through which steel passes before solidifying in the moulds. It is in the tundish that the last traces of non-metallic inclusions should be removed, otherwise the inclusions carry over to the moulds and cause defects in the steel product. In the tundish, the slag is less dense than the melt and thus resides on the top of the melt. The slag provides a sink into which the non-metallic inclusions float to and dissolve. The slag also protects the melt from air and heat loss. However, when slag is entrained in the melt as a result of increased turbulence or shearing at the steel-slag interface, slag can become a source of nonmetallic inclusions.Numerous studies on flow patterns in the tundish have been carried out since the introduction of the tundish. These studies were aimed at improving the flow characteristics in the tundish (Chattopadhyay, Isac, and Guthri, 2010; Cloete, 2014; Jha, Dash, and Kumar, 2001; Jha, Rao, and Dewan, 2008;"

Jan 1, 2017

By T. H. Yang, K. K. Lee, Z. Z. Liang, C. A. Tang, L. C. Li, Y. Tsui, L. G. Tham

Abstract: A series of numerical tests of hydraulic fracturing in heterogeneous rocks were performed to investigate the influence of pore pressure magnitude and gradient on initiation and propagation of tensile fractures. The numerical tests were run with a Rock Failure Process Analysis code, F-RFPA2D, incorporated with a Flow-Stress-Damage coupling model (FSD). To investigate the influence of pore pressure magnitude on fracture behaviour, “pinch-off” breaking tests, originally employed by Bridgeman to investigate the effective stress law for tensile fracture in a uniform pore pressure field, were numerically modelled. In another numerical test, a double-notched sample, with fluid pressure in one notch while keeping the other one open to the atmosphere, is numerically extended to investigate how the fluid flow direction or the pore pressure gradient will influence the fracture behaviour. The simulation results show that fracture is strongly influenced by both pore pressure magnitude and pore pressure gradient. Keywords: seepage mechanics; heterogeneous; pore pressure; numerical simulation; failure process ZUSAMMENFASSUNG: Um den Einfluss der Wasserdruckgroesse der Oeffnung und der Porisitaet auf den Bruchentstanden und Verbreiten der Tension von Gebirgen zu beurteilen, wurde viele nummerische Pruefungen auf den hydraulischen Bruch in dem Gebirgen aufgenommen. Diese Pruefungen wurden mittels der Analyse- Software F-RFPA2D und Flow-stress-Damage Coupling model ( FSD) durchgefuehrt. Um den Einfluess der Wasserdruckgroesse der Oeffnung auf den Bruch zu beurteilen, wurden auch Bruchpruefung und nummerische Analogexperimenten gemacht, und dadurch wurde die ganze Phase der Bruchentstanden und Verbreiten wiedergezeigt, und die Ergebnissen ergeben sich, dass die Wasserdruckgroesse der Oeffnung und der Porisitaet sehr viel auf den Bruchentstanden und Verbreiten der Tension von Gebirgen beeinfluessen. Schluesselwoerter: Durchlaessigkeit , ungeleichmaessig, Wasserdruck der Oeffnung, nummerische Analog, Zerstoerungspahse Résumé : Une série de simulations numériques a été ménée pour analyser l’influence de la grandeur de la pression de pore et du gradient sur la naissance et la propagation des fractures de tensions par le biais de la simulation numérique des fractures hydroliques dans des rochers hétérogènes . Le logiciel F-RFPA (Rock Failure Process Analysis code ) intégrant FSD ( Flow-Stress-Damage coupling model ) y a été employé. Les résultats des simultations montrent tout le processus de la naissance et de la propagation des fractures sous la pression de pore. Ces résultats nous ont permis de constater que la grandeur de la pression de pore et le gradient exercent une influence importante sur la naissance des fractures dans les rochers et sur leur mode de propagation . Mots de clé : le mécanisme de transfusion ; l’hétéogénéité ; la pression de pore ; la simultation numérique ; le processus destructif

Jan 1, 2003

A number of issues relating to the computational aspects of pillar design are addressed in this paper. The computation of average pillar stress values is important when attempting to establish criteria for pillar design and in the analysis of the stability of tabular pillar layouts. One of the default ?classic? numerical methods that are used to determine pillar stresses is the displacement discontinuity method. In many instances it is not clearly understood that this approach does suffer from some limitations, particularly in relation to the fact that in coarse element simulations, the simulated average pillar stress (APS) can depend on the chosen mesh size. The nature of this error is highlighted in this paper and some strategies are suggested to bound the magnitude of these errors. It is demonstrated as well that the popular linear stiffness approximation to pillar or seam compressibility does appear to allow reasonably accurate estimates of the average pillar stress when either the pillar height is varied or when the seam modulus differs from the host rock modulus. A practical implication of this study is that if the seam modulus is noticeably lower than that of the host rock, such as for coal seams, it is important to use a linear stiffness constitutive model for the pillars rather than a ?rigid? pillar assumption. This added complexity seems unnecessary, however, when simulating hard rock pillars in mines where the seam modulus is very similar to that of the surrounding rock.

Jan 1, 2011

By K. -H. Lux, Z. Hou

ABSTRACT: It is well known in underground mining and waste disposal that the development of excavation damaged zones (EDZ), and thus, hydraulic pathways, is closely related to the excess in the corresponding damage boundary (= long-term strength) of the rock mass and the resulting damage. By integrating short-term and long-term strength, dilatancy, damage and healing into the newly extended Hou/Lux constitutive model for rock salt, it is possible to treat the tertiary creep, to identify the EDZ around underground facilities and to predict the time-dependent development of the EDZ in rock salt. Under in-situ conditions, the EDZ of a 37-year-old drift at the Sondershausen salt mine and the EDZ around a drift dam in rock salt are numerically examined. The numerical analysis gives satisfactory results. RÉSUMÉ: Dans les exploitations minières et le stockage souterrain des déchets, le développement des zones endommagées et fracturées (EDZ – excavation damaged zone), créant des chemins préférentiels pour écoulement, est étroitement lié au contexte géotechnique et à la méthode d’excavation. En intégrant la résistance court et long terme, la dilatance, l’endommagement et le colmatage, le nouveau modèle rhéologique Hou/Lux pour le sel gemme est capable de traiter le fluage tertiaire, d’évaluer l’extension de l’EDZ et de prédire l’évolution de EDZ dans temps autour des ouvrages creusés dans le sel gemme. L’EDZ d’une galerie datée de 37 ans dans la mine de sel de Sondershausen et les EDZ autour de barrage des galeries dans un sel gemme ont été modélisées. Les résultats numériques fournissent des résultats satisfaisants. ZUSAMENFASSUNG: Bekanntlich ist die Entstehung von Auflockerungszonen und damit hydraulischen Wegsamkeiten in der unmittelbaren Umgebung um bergmännische Hohlräume mit der Überschreitung der entsprechenden Schädigungsgrenze eng verbunden. Unter Berücksichtigung der Bruchfestigkeit, Schädigungsgrenze, Dilatanz, Schädigung und Verheilung kann das Stoffmodell Hou/Lux das Verhalten des tertiären Kriechens beschreiben, die Auflockerungszone im Salzgebirge ermitteln und ihre zeitabhängige Ausdehnung vorausberechnen. Mit diesem Stoffmodell werden die Auflockerungszonen einer 37jährigen Strecke in der Salzgrube Sondershausen und die Auflockerungszonen um ein exemplarisches Abdichtungsbauwerk im Salzgebirge numerisch untersucht. Dabei werden zufriedenstellende Berechnungsergebnisse erzielt.

Jan 1, 2003

By A. Mainza, A. Mabentsela

A finite element model of a 5 m radius DC arc ilmenite furnace in idling mode was used to test the notion that the slag solidifies when it comes in to contact with colder pig iron, thus constituting the initial step in the formation of solid slag at the slag-pig iron interface. It was found that a slag that is 150°C hotter than the pig iron does not solidify at the interface. The 150°C temperature difference between the slag and pig iron is a result of solid slag at the slag-pig iron interface, not the other way around as suggested in the literature. Calculations show that the thickness of the frozen slag at the slag-pig iron interface is 1.7 cm for the furnace used. It is proposed that slag solidification begins with the slow co-current flow of molten slag and pig iron in the outer parts of the furnace. This provides enough time for molten slag to interact with molten pig iron without solidifying. As the reduction products form due to reduction of the slag by carbon in the pig iron, the slag solidifies. This approach negates the need for the slag to solidify by merely coming into contact with an inherently colder pig iron. Making use of a low thermal contact conductance between the slag and pig iron was found to be sufficient to numerically capture the presence of solid slag at the slag-pig iron interface and to preserve the 150C difference between the slag and pig iron phase.

Mar 30, 2023

By D. K. Weatherley, T. P. Oladele, L. B. Bbosa

Comminution is a critical stage of mineral processing which aims to reduce the size of ore particles through breakage, consequently increasing the likelihood of liberation of valuable minerals. Several factors, such as pre-existing cracks, mineralogical composition and particle size, are known to affect ore breakage behaviour. While investigating the contributing role of each factor is essential to improve understanding of breakage, isolating individual factors by experiment is typically impractical. Numerical techniques such as the Bonded Particle Model-Discrete Element Method (BPM-DEM) have been developed as a means of studying closely controlled breakage conditions. This study evaluates this technique in modelling the effect of pre-existing cracks breakage behaviour for synthetic ore specimens during impact breakage in a short impact load cell (SILC). Synthetic ore was modelled as a collection of discrete entities connected by brittle-elastic beams. Model parameters were calibrated against macroscopic material properties of a conventional homogenous synthetic ore. The extent of pre-existing cracks within specimens was prescribed by varying discontinuities between the connecting entities. An approach with the insertion of seed points was used to model the mineralogy of the specimens. Results showed that pre-existing cracks resulted in a decrease in the fracture force as the crack density increased. Additionally, the irregularity of fracture patterns within rock specimens after impact became more apparent as the crack density increased. The findings were used to emphasise some of the attributable causes of the variation observed between ore hardness characterisation tests and in situ ore behaviour. Keywords: Element Method; Bonded Particle Model, synthetic rock sample; rock fracture, preexisting cracks

Jan 1, 2020

By S. J. Webber

This paper reports on the use of the MINSIM-D stress-analysis program for the modeling of two large seismic events that occurred on the same fault eleven years apart. It was found that the first event (magnitude 5,2) could not be ascribed to purely mining-induced stresses, indicating that the largest seismic events probably result from the interaction of mining-induced stresses with large scale tectonic stresses. However, the stress changes induced during eleven years of mining were found to be capable of generating sufficient excess shear stress (ESS) to be responsible for the second event (magnitude 4,3), The upper limit for the magnitude of purely mining-induced events was found to be approximately 4,3.

Jan 1, 1990

By A. Pellegrino, F. Collin, C. Guiducci, R. Charlier

A numerical approach for modeling coupled Hydro-Mechanical fracture behavior in 2D is presented in this paper. This approach accounts for the strong dependence of the flow characteristics on fracture apertures and offers an anisotropic description of the flow propagation in the fracture. An interface finite element and a constitutive model are developed . In order to validate the applicability of the model to general geomechanic problems, 2D simulations were performed. Results show the good application of the mathematical model and the fundamental hydraulic role played by the fractures. In diesem Beitrag wird ein Stoffgesetz vorgeschlagen um hydromechanisches Kluftverhalten numerisch zu Modellieren. Dieser Vorgang nimmt die starke Abhängigkeit der Fliesseigenschaften von der Kluftöffnung mit in Anbetracht. Ein Interfaceelement und ein Stoffgesetz wurden entwickelt. Zum validieren der Anwendbarkeit dieses Modells wurden 2D Simulationen durchgeführt. Ergebnisse haben gezeigt dass das mathematische Model anwendbar ist und dass Klüfte eine fundamentale hydraulische Rolle spielen. Une approche numérique pour la modélisation du comportement couplé hydro-mécanique des fractures en 2D est présentée dans ce papier. Cette approche prend en compte la forte dépendance des caractéristiques du flux de fluide sur les ouvertures des fractures et présente une description anisotrope de la propagation du flux dans la fracture. Un élément fini d'interface et un modèle constitutif sont développés. Dans le but de valider l'applicabilité du modèle à des problèmes généraux de géomécanique, des simulations 2D ont été réalisées. Les résultats montrent la bonne application du modèle mathématique et le rôle hydraulique fondamental joué par les fractures.

Jan 1, 2003

By J. W. Latilla, J. J. van Wijk

In late 1997 a request was received to assist with determining the powered support unit (shield) load capacities for the planned 2 seam short wall. This project had a number of aspects which made it attractive to utilize numerical modelling in conjunction with other more conventional design tools in the design of the shields. Amongst these were: The 2 seam panels were to be laid out about 25 m below the previously short walled 4 seam, the 4 seam had in turn been over-mined by the 5 seam long wall, the proposed face height of the 2 seam short wall was 5.5 m while the 4 seam had been mined at 4 m. The top seam in the area (5 seam) had been mined at between 1.5 and 2.2 m high, the face conditions with about 95 m of broken material applying dead weight loading to the 2 to 4 seam inter-burden septum were hard to predict and cyclical loading due to the presence of strong sandstone bands in the 2 to 4 seam inter-burden. The basic thrust of the study was to take the known, and successful, situation (4 seam short wall) and carry out comparative modelling to enable prediction of likely 2 seam conditions. Some two dimensional aspects studied were: 5 m goaf hanging up behind shields, stresses in beams to determine likely first goaf roof span, stresses in cantilever beams to asses cyclical loading due to sandstone bands in the interburden being loaded by the overlying goaf and stresses on chain and crush pillars adjacent to the goaf edge. Three dimensional aspects that were investigated included: Load distribution along face for close goafing and 5 m goaf hang-up and load in a 1 m wide rib modelled in the position of the powered support units. From the modelling it was possible to determine the optimal shield leg capacity of the new 2 seam equipment. These outputs were used when drawing up the technical specifications for manufacture of the new equipment. The face was successfully commissioned in August 2002. Fin 1997, requête fut faite pour aider à la détermination des capacités de charge pour l’unité de soutènement mécanisée (bouclier) pour la couche 2 courte taille en projet. Certains aspects de ce projet le rendaient intéressant pour utiliser la modélisation numérique en même temps que d’autres méthodes conventionnelles pour la conception des boucliers. Parmi ces aspects se trouvaient : Les panneaux de la couche 2 devaient être placés environ 25 m au dessous de la couche 4 courte taille ; la couche 4 avait été remplacée par la couche 5 longue taille ; la hauteur de taille proposée pour la couche 2 courte taille était 5.5 m, tandis que la couche 4 avait été exploitée à 4 m. La couche supérieure de la région (couche 5) avait été exploitée entre 1.5 et 2.2 m de hauteur ; il était difficile de prédire les conditions de taille, avec environ 95m de matériaux cassés ajoutant une charge morte à la plaque de séparation entre les couches 2 et 4 et un chargement cyclique causé par des bandes de grès dans l’entre-fardeau 2-4. L’idée principale de l’étude fut de prendre la situation connue et réussie (couche 4 courte taille) et de faire une modélisation comparative pour prédire les conditions probables de la couche 2. Certains des aspects à double dimension qui furent étudiés étaient : Un accrochage de remblai de 5m derrière les boucliers ; contraintes dans les poutres pour déterminer le premier intervalle probable entre remblai et toit ; contraintes dans les poutres en porte-à-faux pour évaluer le chargement cyclique causé par les bandes de grès dans l’entre-fardeau qui est accablé par le remblai et les contraintes sur les piliers par chaîne et d’écrasement adjacents au bord du remblai. Aspects à trois dimensions qui furent étudiés : Distribution de la charge le long de la taille pour les remblais proches et l’accrochage de remblai de 5 m et la charge dans une nervure de 1 m de large modelée dans la position des unités de soutènement mécanisées. La modélisation a permis de déterminer la capacité de portée optimale du bouclier du dispositif nouveau pour la couche 2. Ces résultats furent utilisés pour dresser les spécifications techniques pour la fabrication de l’équipement nouveau. La taille fut commissionnée avec succès en août

Jan 1, 2003

By R. J. Pine, J. M. Rance, J. S. Coggan

ABSTRACT: The safe design of excavations created in a fractured rock mass is of paramount importance in rock engineering. Depending on the nature of the stress regime acting on an excavation, and the associated deformational behaviour of the rock mass surrounding the excavation, a number of potential failure mechanisms exist. These involve a combination of shear failure on existing joints, extension of critically oriented joints and propagation of new fractures through previously intact rock. Conventional numerical codes usually adopt either a continuum or discontinuum approach; this often results in significant over simplification and kinematic limitations particularly when modelling complex rock mass behaviour in the close vicinity of excavations. This paper describes the results from several case examples using a combined finite element-discrete element code, ELFEN that incorporates a crack propagation mode. Through the use of selected rock engineering examples, the authors demonstrate the potential of the code in the realistic simulation of complex rock failure both in underground and surface excavation applications. RÉSUMÉ: La conception sûre des excavations créées dans une masse de roche fracturée est d'importance primordiale dans la géotechnique. Selon la nature du régime d'effort autour d’une excavation, et le déformation associé de la masse de roche autour de l'excavation, il exsite un certain nombre de mécanismes potentiels d'échec. Ceux-ci comportent une combinaison d'échec de cisaillement sur les joints existants, la prolongation des joints d’orientation critique et la propagation de nouvelles ruptures dans la roche précédemment intacte. Les codes numériques conventionnels adoptent habituellement l’approche, soit d’un continuum, soit de discontinuum; ceci a souvent comme conséquence une sursimplification significative et les limitations cinématiques en particulier en modelant le comportement complexe de la masse de roche très proche des excavations. Cet article décrit les résultats de plusieurs exemples de cas en utilisant un code qui s’agit d’une combination d’élément discret et d'élément fini, ELFEN qui incorpore un mode de propagation de fissure. Par l'utilisation des exemples choisis géotechniques, les auteurs démontrent le potentiel du code dans la simulation réaliste de l'échec complexe de roche pour les applications aux excavations soit au fond soit à l’extérieure. ZUSAMMENFASSUNG: Das sichere Design der Aushöhlungen, die in einer zerbrochenen Felsenmasse verursacht werden, ist vom paramount Wert in der Felsentechnik. Abhängig von der Natur des Druckregimes, das auf einer Aushöhlung und dem dazugehörigen deformationalen Verhalten der Felsenmasse umgibt die Aushöhlung fungiert, bestehen eine Anzahl von möglichen Ausfalleinheiten. Diese beziehen eine Kombination des Scherausfalls auf vorhandenen Verbindungen, Verlängerung der kritisch orientierten Verbindungen und Ausbreitung der neuen Brüche durch vorher intakten Felsen. Herkömmliche numerische Codes nehmen normalerweise entweder ein kontinuum oder discontinuum Annäherung an; dieses ergibt häufig bedeutende Übervereinfachung und kinematische Beschränkungen, besonders wenn es kompliziertes Felsenmasseverhalten in der Nähe der Aushöhlungen modelliert. Dieses Papier beschreibt die Resultate von einigen Fallbeispielen mit einem kombinierten begrenzten Element - getrennten Elementcode, ELFEN, das einen Sprungausbreitungmodus enthält. Durch den Gebrauch von vorgewählten Felsentechnikbeispielen, demonstrieren die Autoren das Potential des Codes in der realistischen Simulation des komplizierten Felsenausfalls bei Anwendungen für beide Tagebaue und Untergrundsaushöhlungen.

Jan 1, 2003