Search Documents

By S. Mohanta, B. C. Melkap

"SynopsisDry beneficiation of coal by air dense medium fluidized bed is an emerging trend. It is widely believed that the particle size of the medium has a significant effect on the separation efficiency. This investigation demonstrates that medium particle size has a major effect on separation efficiency. Experimental results show that different size fractions of the same feed respond differently to the same size fraction of medium solids. Furthermore, a particular size fraction of feed coal responds differently with different size fractions of medium solids. The Ep values and overall metallurgical performance parameters, obtained from experimental results, clearly indicate the superior performance of an air dense medium fluidized bed separator when using –150+106 µm magnetite powder as the fluidizing medium. These observations reinforce the importance of sizing the medium particle size for the air dense medium fluidized bed.IntroductionIn an air dense medium fluidized bed (ADMFB), a fluidizing bed of a particular density is created by suspending solid particles in an upward air flow. A feed containing coal particles of different densities is introduced into this fluidizing bed. The particles with relative density less than the bed density float on the top of the bed, while particles denser than the bed density sink through it. Since there is a general correlation between ash content and density of coal particles, it is possible to remove ash-forming impurities from a raw coal to the required level by regulating the density of the fluidizing bed. Recently, the ADMFB process has received significant attention world-wide for its specific advantages of low operating cost and less restrictive for small capacities (Luo and Chen, 2001; Houwelingen and de Jong, 2004; Dwari and Hanumantha Rao, 2007; Sahu et al., 2009; Mohanta et al., 2012). This process is not recognized as a well-established industrial practice because of the availability of efficient wet processing technology. However, with the revival of interest in dry beneficiation of coal in general, and ADMFB in particular, there is a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have made the process a competitive and viable option for beneficiating coal."

Jan 1, 2015

By L. Cornish, P. A. Olubambi, J. H. Potgieter

Four 22%Cr series duplex stainless steels alloys containing varying nickel contents of approximately 5, 7, 9 and 13% were melted in a vacuum induction furnace, hot rolled, solution annealed and water quenched. Their corrosion behaviour was investigated in sulphuric acid and sodium chloride solutions using a potentiodynamic polarization technique. Increasing nickel contents have appreciable influence on their corrosion behaviour. Polarization curves show similarities in the uniform corrosion behaviour of the alloys in the solutions and a significant difference in their pitting behaviour in chloride environments. Alloy 2209 generally exhibited highest resistance to uniform corrosion while 2213 displayed distinct and best pitting corrosion resistance. Their corrosion behaviour were attributed to the influence of nickel on phase modification, microstructural refinement, and the probably types of films formed in different environments. Keywords: Duplex stainless steel; Nickel; Microstructure; Phase modification; Corrosion

Jan 1, 2006

By F. Dehghani

The influence of different grinding methods on the shape characteristics of magnetite particles was investigated. Also, the effect of particle shape on the flotation of the magnetite, both alone and in the presence of quartz particles, was investigated. The shape characteristics of the magnetite particles were measured and calculated from images obtained by scanning electron microscopy via an image analysis system. The flotation tests were performed using a laboratory flotation cell. Results showed that in the -250+212 µm and -106+75 µm size fractions, ball mill products have a higher elongation value than rod mill products, while in the -150+125 µm size fraction, rod mill products have a higher elongation value. Particles with higher elongation values and lower roundness values have a higher flotation kinetic constant. Furthermore, the influence of magnetite particle shape on flotation is greater, and the flotation kinetic constant is higher, in the presence of quartz particles than in the flotation of magnetite alone Keywords shape, elongation value, flotation kinetics, magnetite.

Dec 1, 2013

By L. Kühnel, H. Lieberwirth

Confined bed comminution in High Pressure Grinding Rollers (HPGR) and Vertical Roller Mills (VRM) is gaining substantial attention in many applications. Previously used mainly for milling coal or construction materials, HPGR and VRM have started to complement or even replace tumbling mills in ore beneficiation. Materials like coal or clinker are relatively homogenous, however, in comparison to metal ores and wall rocks. This characteristic poses a new challenge to the confined bed comminution but also an opportunity. Fuerstenau and Abouzeid have investigated the selectivity in comminution of a mixture of particles of different strength in a particle bed. The median particle size and particle size distribution (PSD) of the two constituents used were kept constant. Only the proportion of the two constituents was modified. The competence of a material is, however, also a function of particle size. Smaller particles tend to be more competent than larger ones of the same material. If selective comminution is applied on ores, this size influence has to be understood. The paper presents research results on this topic based on experimental investigations with model materials as well as with natural particles, which were stressed in a piston-die press. It appeared that the comminution result depends substantially on the material characteristics and the composition of the mixture. Conclusions will be drawn for the application in future applications of selective comminution in mineral processing. Keywords: Confined bed comminution, HPGR, VRM, piston die press, particle size

Jan 1, 2020

By V. Labiouse, R. Gärber

The paper aims at clarifying the up-to-now misappreciated role taken by pore water on the design of deep tunnels in saturated porous media. Numerical simulations with a non-dimensional FEM-model emphasise the influence of pore water characteristics (in situ pressure and compressibility) and boundary conditions (lining permeability) on the short and long term underground-structure equilibrium states. These results cannot be achieved by means of monophasic total stress analyses. Dieser Beitrag untersucht den Einfluss des Porenwassers auf die Dimensionierung von tiefen Tunnelbauwerken in wassergesättigtem Untergrund. Numerische Simulationen mittels eines dimensionslosen FEM-Modells betonen den Einfluss der Porenwassereigenschaften (in-situ Druck und Kompressibilität) und der hydraulischen Randbedingungen (Tunnelausbaudurchlässigkeit) auf Kurz- und Langzeitverhalten des Untergrund-Ausbau Gleichgewichts. Diese Ergebnisse können nicht ermittelt werden anhand von Einphasen- und Totalspannungsmodellen. L’article s’intéresse au rôle méconnu de l’eau interstitielle dans le dimensionnement de tunnels profonds creusés dans des milieux poreux saturés. Des calculs adimensionnels par éléments finis soulignent l’influence des caractéristiques de l’eau interstitielle (pression in situ et compressibilité) ainsi que des conditions aux frontières (perméabilité du revêtement) sur les équilibres court et long terme de l’ouvrage. Ces résultats ne peuvent pas être obtenus par des calculs en contraintes totales.

Jan 1, 2003

By S. T. L. Harrison, M. Smart, C. J. Edward

Biooxidation, a biohydrometallurgical process, utilizes a mixed microbial consortium to mediate the dissolution of refractory gold-bearing ores to enhance gold recovery during cyanidation. Recognition of water as a critical resource has prompted improved water management strategies within mining and minerals processing. Bioremediated wastewater from the cyanidation tailings provides a potential water source to supplement the water required for the biooxidation circuit, reducing freshwater extraction. Gold biomining operations have typically been reluctant to recycle this wastewater due to the potential inhibitory effects of cyanide and thiocyanate (SCN-) on the microbial population. Historical process upsets suggest that the microorganisms are sensitive to SCN- concentrations as low as 1 mg/L. However, effective bioremediation processes resulting in effluents with low or negligible SCN- concentrations may allow gold biomining plants the opportunity to recycle available water. Microbial activity as well as alteration in community structure were monitored as a function of increasing SCN- concentration over the range of 0 mg/L to 5 mg/L to investigate the response of the biooxidation community to potential SCN- spikes resulting from upsets in the remediation process. Appropriate microbial growth and ferrous iron oxidation activity with a nominal shift in community structure were observed at SCN- concentrations up to 1 mg/L. Thiocyanate concentrations above 1 mg/L resulted in the complete inhibition of ferrous iron oxidation activity. This was attributed to Leptospirillum ferriphilum’s sensitivity to SCN-. Exposure to a SCN- concentration of 5 mg/L resulted in a lower cell concentration and a significant increase in growth lag time, and the absence of L. ferriphilum from the microbial population. At. caldus and Ap. cupricumulans were still present at 5 mg/L SCN-, although Ap. cupricumulans was unable to oxidise ferrous iron at this SCN- concentration. It was concluded that recycling bioremediated cyanidation tailings wastewater within the biooxidation circuit is feasible; however, to retain process performance, SCN- concentrations should not exceed 1 mg/L. Keywords: Biooxidation, thiocyanate, water recycling, community structure

Jan 1, 2020

By H. M. Chikashi

Keywords: Pyrometallurgy, furnace, bath agitation, regression analysis, entrainment This paper presents the results of linear regression analysis of the influence that each component of slag has on the losses of copper in slag-cleaning-furnace slag. Data used for the analysis are actual plant data collected over the past two years of operation. Facts obtained from the study will be helpful for smelter management to control these components in the flash smelting furnace feed and slag, to levels which will enable better control of copper in slag, and smoother operation of the KCM slag-cleaning furnace.

Jan 1, 2011

By J. A. Venter, M. K. G. Vermaak, J. G. Bruwer

Electrostatic separation is employed in the concentration of zircon and rutile. The zircon concentrate undergoes an acid treatment to remove impurities from the surface of both the zircon and rutile. The purpose of the acid treatment is to increase the difference in the resistivities of the two minerals, thus ensuring the best possible electrostatic separation efficiencies. Previous test work suggested that these impurities are not removed, but only modified; the surface modification seemed more prevalent in the case of the rutile. The resistivity of the rutile changes with pH and thus the electrostatic separation of the rutile is influenced. X-ray photoelectron spectroscopy (XPS) indicates that there is an increase in the OH and adsorbed H2O concentrations on the rutile surface. XPS also showed significant differential charging on the rutile surface, which indicates that the species on the rutile surface have different resistivities. The zircon particles from the conducting and non-conducting streams have similar resistivities and no major differences in their surface species. Zircon losses during the final electrostatic separation appear not to be due to surface effects, but due to shielding of particles during the separation.

Jan 1, 2007

By Dolly Chakraborty, S. Ranganathan, S. N. Sinha

Experiments were conducted to study the influence of temperature, particle size and ore/coke ratio on the kinetics of reduction. The rate of reduction increased with temperature. The reduction of iron was completed at shorter time intervals at temperature above 1000ºC. Usually the reduction of chromium commenced after the reduction of iron was almost complete. Reduction was controlled by diffusion at low temperatures and by chemical reaction at higher temperatures. The nature of the reducing agent had a very significant influence on the rate of reduction. The study showed that chromium was converted into the carbide during reduction. Increasing the size of the reducing agent increased the rate of reduction initially. After a critical size, the rate of reduction decreased. However, increasing the size of the ore particle decreased the rate of reduction, initially. Beyond a critical size, it increased. An optimum particle size of the chromite ore and that of coke must be chosen, particularly in the production of agglomerates to achieve maximum degree of reduction.

Jan 1, 2007

By G. Coetzer

During galena flotation of Rosh Pinah milled material, metal ions and salts contents of various water resources (deionized, simulated circulated, lead concentrate thickener, lead tailing thickener and borehole) influenced mineral recoveries, upgrade ratios, selectivities, froth stability and flotation kinetics. The various water resources employed during galena flotation caused activation, depression or selectivity effects on minerals due to the presence of different ions in solution. Metal ions in these water resources were adsorbed by the ore, whilst ions associated with gangue minerals (dolomite and quartz) were released into the flotation pulp. Lead concentrate thickener water caused depression of sphalerite and pyrite, increased fast floating fractions for silver, copper minerals, sphalerite and quartz (unwanted), and improved slow floating rate selectivity against pyrite and sphalerite. Lead tailing thickener water enhanced sphalerite recovery during galena flotation (unwanted), and increased fast floating fractions of pyrite. Western borehole water did not affect galena recovery, but sphalerite and pyrite recoveries were unacceptably too high. Ions from copper, lead, and zinc salts tended to release high amounts of ions, such as calcium, magnesium, silicon, and manganese from gangue minerals (dolomite and quartz) during milling. During galena flotation, lead ions depressed sphalerite, pyrite and dolomite at a lead concentration of 400 ppm, but sphalerite was activated at a concentration of 800 ppm. Sphalerite was activated with copper ions (89% recovery, 2.09 upgrade ratio) and depressed with zinc ions (maximum recovery of 25%). This corresponds with findings in previous investigations. Dolomite and quartz were slightly activated with zinc ions. No evidence was found that lead and copper ions activated any gangue minerals during galena flotation. Keywords: galena, water resources, metal ions, activation, depression, selectivity.

Jan 1, 2003

By D. Yu, Y. Thibault, D. Paktunc

"Prereduction and flux-aided direct reduction of chromite provide significant advantages in reducing energy consumption and greenhouse gas emissions during ferrochrome production. In this investigation, a comparative evaluation of the influences of several alkali fluxes was carried out based on experimental observations supplemented by advanced material characterization and thermodynamic predictions. Direct reduction of a chromite ore with alkali fluxes at 1300°C for 1 hour produced (Cr,Fe)7C3 type alloys with Cr/Fe mass ratios from 0.7 to 2.3. Among the alkali fluxes, reduction aided by NaOH resulted in a high degree (85%) of Cr metallization with the ferrochrome alloy being Cr4.2–4.6Fe2.4–2.8C3. The formation of liquid slag, which facilitated Cr metallization, was limited by the formation of NaAlO2 between 800 and 1300°C. This, in turn, restricted the collection and transport of the charged ionic Cr species (i.e. O2–) to graphite particles. Under the conditions studied, ferrochrome particles were often small and largely unliberated, which would make the physical recovery of ferrochrome challenging. At 1400°C, the amount of liquid slag increased, enabling the growth of alloy particles. Direct reduction of chromite aided by NaOH is promising as an alternative technology to conventional flux-based smelting in electric arc furnaces. IntroductionConventional smelting processes are energyintensive (Riekkola-Vanhanen, 1999) with the energy requirements greater than 4 MWh/t (Naiker and Riley, 2006; Beukes, van Zyl, and Neizel, 2015), and the greenhouse gas emissions can be significant, exceeding 10.5 t CO2 per ton Cr in ferrochrome produced (International Chromium Development Association, 2016). These include emissions occurring on-site (smelter), emissions due to electricity production, and emissions due to upstream processes. Overall energy requirements are influenced by the degree of prereduction and smelter charge temperature. Significant reduction in electricity consumption can be realized if the charge is prereduced before feeding to the submerged arc furnace (Niayesh and Fletcher, 1986). This consideration has led to the development of several prereduction technologies, with the most important example being the Premus process. In comparison to the conventional smelting processes, this prereduction process lowers the overall energy consumption and greenhouse gas emissions by about one-third (Naiker, 2007)."

Dec 1, 2018

By C. Gatschlhofer, A. Krammer, H. Raupenstrauch, T. Hochsteiner, A. Holzer, L. Wiszniewski

The rising demand for lithium-ion batteries, coupled with international climate targets, emphasises the need for circular economy and zero-waste recycling approaches. However, so far, no industrial-scaled solutions are available that fulfil global recovery targets. Therefore, a novel pyrometallurgical reactor was developed at the Chair of Thermal Processing Technology at Montanuniversitaet Leoben to avoid lithium slagging and recover volatile elements via the gas phase. Nevertheless, previous results show that several impact factors, including interfering elements or pre-treatment steps, strongly limit the recycling efficiency of black mass. To simulate the black mass and provide feedback on possible influences of pre-treatment steps, cathode material from production with additives of interfering elements was analysed regarding melting behaviour. The results show that formation of a further processable alloy was increased by almost 50% when pretreatment steps were excluded, indicating pre-treatment steps as a major influence to be considered within this specific recycling route.

Jan 1, 2023

By L. Marais, S. Denoon-Stevens, J. Cloete

"Historically, mining companies worldwide provided housing and developed towns to accommodate their employees. At the end of the 1980s this approach became less prevalent and attempts were made to mitigate the effects of mine development and mine closure on communities living near the mines. Permanent settlement in mining towns urgently needed to be minimized. Since the advent of democracy, South African policy has moved in the opposite direction, shifting the emphasis to creating integrated communities and encouraging home ownership. Despite this policy shift, however, mines continue to influence local housing conditions. One direct outcome has been the development of informal settlements. We surveyed 260 informal settlement households in Postmasburg, a small and remotely located town in the Northern Cape Province of South Africa. We found that because they employ contract workers and thus arouse expectations of employment, the mines here contribute extensively to the development of informal settlements. But local factors also contribute, and the functional role of informal settlements as a form of housing that supports mobility should not be underestimated. We also found that both municipal and mining company policies for informal settlements were inadequate. Finally, we found that low-income informal settlers not associated with mine employment suffered the highest levels of social disruption.IntroductionA mine generates demand for labour, which in turn generates demand for housing. When settlements spring up near a mine this often means poor housing conditions. In South Africa in the 1960s and 1970s mining companies invested heavily in company towns or mining settlements, but they have become increasingly hesitant to do so, for three reasons. First, declining resource prices in the mid-1980s and the 1990s compelled them to focus on core business interests and reduce the costs of peripheral activities such as housing (Bryceson and MacKinnon, 2013); second, at the turn of the 20th century they were often accused of taking over the role of local government (IIED, 2002) and consequently became hesitant to invest in developing mining towns; and third, changing labour regimes also curbed their investment in such towns (Haslam McKenzie, 2010). Increasingly, the companies began to endorse block-roster shifts, and outsourcing also became more common in the early 1990s. Block-roster shifts in Australia (together with improved technology) have meant that miners do not need to settle near the mines but can fly in and fly out and have their urban houses as their stable homes. This has had serious negative implications for housing in remote towns in Australia, particularly worker camps, large-scale renting out of available accommodation, and ‘hot-bedding’."

Oct 1, 2018

A new system for granting access to mineral rights is proposed in the recently released White Paper, ?A Minerals and Mining Policy for South Africa?. Official policy states that ?Government?s long-term objective is for all mineral rights to vest in the State for the benefit of and on behalf of all the people of South Africa?. In order to achieve this objective, government is presently investigating the feasibility of imposing a financial or tax-related disincentive to holding mineral rights. The paper aims to present the pros and cons and to examine the alternatives which will cause minimal disruption to the minerals industry in the period during which mineral rights are transferred to the State. South Africa is a country whose economic and political history is embedded in the development of its mineral resources and has inherited a system which cannot simply be wished away. Hasty or radical decisions will compound the problem, rather than provide a lasting and widely acceptable solution. Mineral rights ownership and its impact on access to mineral deposits are discussed. Taxation as a possible economic disincentive is also evaluated. Finally, the value of mineral resource related information as a prerequisite to mineral policy decisions and as an alternative to mineral rights taxation is emphasized.

Jan 1, 1999

By R. H. Steel

Ingot casting and wire drawing In Iron Age Southern Africa by R. H. STEEL (Visitor) This paper describes the experiments that were conducted in 1974/1975 on two related aspects of Iron Age copper technology in Southern Africa: ingot casting and wire drawing. Three types of ingot were successfully cast: the St Andrew's Cross ingot, the marale ingot, and the musuku. It is suggested that the 'studs' on the musuku are not the remains of broken-off rods as previously proposed by other investigators, but that the ridged pattern is an ornamental feature. Copper wire was successfully drawn with similar tools and according to the procedures described in the literature on African Iron Age wire drawing. It is concluded that these accounts are generally accurate and that the pre-European metal workers are worthy of respect for the results they achieved with primitive methods.

Jan 11, 1975

By J. Dienenthal

Automatic Charging and Stoking Machines for use at ferroalloy furnaces are in operation for more than 20years. Dango & Dienenthal Maschinenbau GmbH (short: DDS) has developed several machine generations. Today advanced solutions help to achieve better charging and stoking results to minimize cost and to improve the working environment around the furnaces. Three different alternatives can be considered: Rail-mounted solution The machine(s) travel(s) on an overhead monorail to one or several furnaces and is locked in the desired working position from where charging and stoking is performed. Mobile solution This machine travels on the charging platform and is also locked at the respective working position to perform charging and stoking. Automation of a standard mobile charging and stoking machine A standard charging and stoking machine can be adapted for automation. A reliable navigation system is included. Charging and stoking is performed with the moving machine. Advantage versus other solutions: considerable lower investment cost and possibility to upgrade the mobile charging and stoking machine for later automation. Overall, automatic charging and stoking can save up to 10 per cent of the specific smelting energy. A better and more consistent furnace operation can be achieved. Different programs are used to cope with different furnace conditions and changing raw materials. All machine movements can be recorded and correlated to other furnace parameters. Working environment on the charging platform is greatly improved.

Jan 1, 2007

By C. N. Harman

Steel is the most versatile material which has made the progress in every aspect on this earth possible. There are hundreds of varieties of steel because for each application it has to be made with specific properties to get the most optimum usage. It is well known that the basic constituent of steel is iron. But it is the proportion of other elements in it, which give each type of steel certain specific properties. These elements are added in liquid iron inform of Ferro alloys to get the desired composition and properties. Thus, Ferro alloys are important additives in the production of steel. It can be said that no steel can be made without use of one or more of the several Ferro alloys. They form the backbone of steel. Thus, the Ferro alloys industry is vitally linked for its growth and development to that of the steel industry. Ferro alloys industry in India has never been globally competitive, despite its rich ore deposits and low-cost manpower, essentially due to a) Insufficient availability and high cost of electric power b) Increasing ores and reductants cost c) Non-availability of low ash, low phos. coking coal in the country for the production of desired coke with low ash, and low phos. contents, making import of such coke at a high cost imperative d) High-cost and insufficient infrastructural facilities (both road and rail) for rapid transportation of ore from mines to plants e)Stiff competition from producers and exporters of Ferro alloys in other countries like South Africa, Kazakhstan, China, Russia, Australia etc. due to global trade agreement which has made drastic reduction in customs duty on imports necessary. f) Wide fluctuations in the International price of Ferro alloys depending on demand versus supply. To over come these challenges plus adhering to stringent pollution control norms innovations are inevitable in the process technology, and plant equipment design, along with frequent changes in product mix, to be more cost-effective. An attempt is made in this paper to address the innovations that took place in the past and those that further need to be made, considering the future of this industry.

Jan 1, 2007

By C. van Tonder

Paper written on project work carried out in partial fulfilment of B Tech (Engineering Metallurgy) degree This investigation relates to a multi-purpose electrolytic system. Its primary purpose is to electrowin gold from high or low concentration gold cyanide solutions and/or from gold sludge, and to convert the recovered gold into a gold (alloy) electroform or electrode at the gold mine itself. These operations are carried out sequentially and in situ in the same electrolytic cell. Electrorefining of the gold recovered may also be done in the cell. The system applies to silver as well, and may be adaptable to base and platinum group metals. It could also be used in environmental applications, to remove undesirable metals present in aqueous solution at very low concentration. The work to be discussed forms part of recently filed patent applications. Subsequent and future developments of the system are briefly outlined. This paper, in part or in full, has been published by the Metallurgical Mine Managers Association (MMMA), with permission from the authors.

Jan 1, 2006

By B. Leong, H. Joubert

Keywords: Pyrometallurgy, furnace, auxiliary equipment, copper slag launders Pyromet has designed copper launders for tapping slag. What makes Pyromet?s launder design innovative and safe is that it does not have any cooling water channels underneath the launder runner, whilst achieving effective cooling of the runner. If matte burn-throughs were to occur through the launder runner, the risk of damaging water channels and the risk of explosions are reduced. In addition, since the cooling water channels are not harmed, the launder is easily repairable and reusable. Pyromet makes use of Finite Element Analysis to optimize the launder geometry to ensure that sufficient energy is removed from the centre of the launder. Factors considered during the launder design include the suitability of the geometry to the client?s needs, experience from existing installations, and ease of fabrication. Pyromet goes so far as to develop procedures for fabricators to ensure that fabrication issues do not compromise the functionality of the launder. When launder orders are received by Pyromet, the entire fabrication process and the functioning of the launders during operations are monitored to ensure that the launder designs are continuously improving with every installation.

Jan 1, 2006

By S. Lin

A new hydrogen production process, named the HyPr-RING, has been proposed. Fundamental concept of the HyPr-RING is integration of water carbon reaction, water-gas shift reaction and CO2 absorbing reaction in a single reactor. Firstly, thermodynamic analysis was done to judge the possibility to realize the process. It was found that high pressure and temperature condition, such as 20 MPa and 1000 K, is required to promote this integrated reaction. Next, experimental verification of the new process was done under the high pressure and temperature reaction conditions. As the results, integration of above three reactions in a single reactor can be done successfully and produced a large amount of hydrogen as estimated by thermodynamic analysis. Experiments showed that organic materials including coal, heavy oil, biomass, plastics can be used in this process. In the gaseous phase, no pollutants such asH2S, SO2, COS are detected so that gas cleanup system is not required for power generation when this process is used. Finally, a process design was made to estimate process efficiency. Theoretically, 1 mole of carbon can generate 2 moles of hydrogen and cold gas efficiency of this process estimated as more than 80 per cent. The process potentially reduces hydrogen production cost compared with the conventional hydrogen production methods. Keywords: Hydrogen, Fossil fuel, Energy, Process, Supercritical water

Jan 1, 2001