Search Documents

By Will B. Jamison

An ignition detection and suppression system was developed under the scope of this contract. The objective of this machine mounted system was to detect flames caused by frictional sparking from the cutting bits of a continuous mining machine and to suppress it with sufficient speed to prevent the development of an explosion, and to keep the flame from harming the machine operator.

Jan 1, 1976

Surface mining and reclamation of a southeastern Ohio site with sandstone-shale overburden resulted in (as compared to premining levels): 1) runoff volumes and peak rates that increased by a factor of from 2 to 10 during mining and after reclamation, 2) destruction of the "aquifer" perched on the underclay of the mined coal bed and gradual, but, as yet incomplete redevelopment of this aquifer after reclamation, 3) no immediate effect on another, lower perched "aquifer", 4) up to 100 times greater sediment concentrations in runoff. Results were influenced by increasing annual precipitation amounts through the period of record; 1978, 1979, and 1980 (postreclamation years) experienced precipitation amounts approaching or exceeding long-term normalcy for the area. Part of the reason that the site produced more runoff after reclamation than before mining is that the premine condition was one of an open, porous soil under woodland, while the postreclamation condition was one of a compacted, bulldozed soil. Sediment concentration results were influenced by failure of the postreclamation erosion control system and by a series of detention reservoirs above the stream monitoring station.

Jan 1, 1983

By John D. Rockaway

Failure of the mine floor supporting coal pillars frequently occurs when the subcoal strata include "underclays" or other low strength strata. The failure process has been studied to define the response of these materials to applied coal pillar loads and to determine the applicability of bearing capacity analysis to evaluate unsafe conditions. The study has been accomplished through an investigation of both the intact and insitu geotechnical properties of the subcoal strata and through the installation of floor movement monitoring instrumentation. The results of these studies have indicated that both the shear strength of the underclay and the stratigraphy of the subcoal strata must be considered in the analysis. The shear strength was the major controlling factor determining the ultimate load carrying ability of the materials, but the thickness and stratigraphic position of the weak layers influenced the mechanism of the failure process. The methods of bearing capacity analysis were used to define pillar stability that included provisions for taking into consideration a two-layer system. Conditions assumed for a coal mine where a weak underclay overlies firmer strata. The results of the analysis compared very well with observed mine conditions, indicating marginal conditions in areas of the mine which later experienced pillar support failure. In addition, a "heave factor" was derived to predict potentially unstable floor conditions in the mines studied in detail.

Jan 1, 1979

By O. H. Metzger

This is one of a series of papers being published by the Bureau of Mines on mining areas and districts in the Western states. It describes mining and milling practices in the vicinity of Wickenburg in Maricopa and Yavapai Counties, Ariz. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of the operators of the mines visited. Reports of geologists and engineers who previously visited the area were drawn upon freely. Individual acknowledgments are made in the text.

Jan 1, 1938

By Thomas Gales

Longwall mining has a high potential for producing bulk production from a single face. Production is interrupted for a considerable time when it is necessary to move the equipment to a new block of coal. The frequency of such moves can be reduced by increasing the dimension of the block to be moved. Merely doubling the tonnage in a block to be mined may increase production by more than 21,000 tons per year. The time taken to move the equipment can be reduced by careful preplanning, industrial engineering analysis, and specially designed equipment. Reducing its move time from 30 days to five days can increase production by more than 25,000 tons per year. Increasing the panel dimensions and reducing the move time can give an increase in pretax profits of more than $600,000. A comprehensive bibliography is included.

Jan 1, 1977

By D. V. Gaffney

This report presents the results of a three-phase investigation of the feasibility of using cemented coal waste in active underground coal mines to prevent mine subsidence. Coal caste was broadly defines to include waste from both coal preparation plants and coal-fired power plants. Underground systems with potential for cemented backfill are determined through identification of current mining methods and available technologies for cemented backfilling and consideration of materials and systems constraints upon mining and backfilling integration technical concerns including operation, health and safety, materials utilization, environmental impact, applicability and techni¬cal status are assessed for six (6) systems which were identified as potentially feasible. Two (2) of these systems are conceptualized in a hypothetical case history and developed to further assess their operational and economic feasibility. Comparisons of costs among both systems and with costs of surface disposal are presented. Also presented are the conclusions reached concerning the present feasibility of using cemented backfill in active coal mines and potential avenues for further research. Appendices contain further consideration for design of cemented mixtures to be used in backfilling, the results of laboratory testing of mixtures rich varying concentrations c: waste products and cementing agents, and an annealed bibliography

Jan 1, 1981

By Forrest T. Moyer

[The safety record of the nonmetal mining industry during 1965 way worse than that of 1961 in all general measures s of injury experience except for a slight improvement in the number and frequency rate of nonfatal injuries Work fatalities in 1965 totaled al and occurred .it a frequencyrate of 0.29 and a severity rate of 1,711 per million man-hours of worktime. The fatality total was seven oven higher than to 1964 and the injury ratess increased d 32 and 28 present, respectively Thin total. of 2,172 nonmetal injuries u- in 1965 was 3.4 less than in 1964 and the frequency rate per million ion man-hours worked declined percent to 22.73 from: 23.14 in 1964. However, the 1965 nonfatal severity rate of 1,339 per million man-hours worked was 15 percent our the: d.96,1 rate of 1,160, This increases was largely attributable to two more permanent total and nine more permanent partial injuries. in 1965 than in the proceeding year. The average severity all injuries in 1965 was 132 days, 1-I. or charged per injury or 25 days more than in 1961. Injury experience in the nonmetal mining industry, including and excluding officeworkers, for the a-year period 1961-65 is shown in table 1. The average number of men working, on active days in 1963 was 48,429, or 635 fewer than in 1961. However, mines and mills, wore active an average: of 5 days more for a total of 277 in 1965, and each worker averaged 2,245 hours compared to 2', 190 hours in 1961. As a result, aggregate worktime of 108.7 million man-hours increased 1 percent over the 1964 total of 107.4 million hours.]

Jan 1, 1970

By T. H. Miller

An attempt has been mace in this publication to present annotated references to all articles pertaining, to ore dressing that were published during 1931 and 1932; in a few instances reference is made to articles published prior to 1931 where the articles have not been included in previous bibliography appended to the annual statistical discussions of ore concentration published by the Bureau of Mines. Articles have been taken from more than 75 periodicals, journals, serials, etc., and 423 articles are abstracted herewith. A number of these abstracts, particularly those appearing in foreign publications, have been taken from Chemical Abstracts (published by the American Chemical Society, Easton, Pa.), the general use of which the authors wish to acknowledge. Other annotations were taken directly from the original publications. The entire field of ore dressing has been included in the bibliography and articles dealing with crushing, grinding classification, concentration, thickening, and filtration have been included, as well as on amalgamation, cyanidation, leaching, magnetic concentration, washing, etc., and on theory and laboratory operation. The articles are arranged in alphabetical order by authors. Lack of printing funds prohibited the inclusion of a subject index.

Jan 1, 1934

By C. M. Harrer

Reconnaissance investigations were made of 129 iron occurrences in Arizona to determine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential western iron markets are discussed. The location, features, qualities, extent, and potential of iron occurrences and some associative resources--limestone and dolomite, coal, petroleum and natural gas, power, and water are discussed. The most abundant iron minerals are magnetite and hematite. The higher grade deposits are extensive contact-metamorphic or pyrometasomatic replacements of calcareous Paleozoic to Proterozoic rocks associated with intrusives. Large low-grade deposits of great potential are present as Precambrian taconite, semitaconite-, and jaspilite-like iron formations of magnetite-hematite. Iron occurs also as low-grade concentrations of magnetite in extensive alluvial deposits. Nonferrous metallurgical slags, nearly 100 million tons, are considered a potential source of iron. Various accessory elements are associated with the iron minerals and these pose metallurgical and economic problems.

Jan 1, 1964

As a part of its overall wealth in fuel resources, the United States possesses large reserves of coal of ignite rank. According to recent estimates of the Federal Geological Survey (3, 5),l/ the assured lignite reserves of this country amount in total to over 463 billion tons, equivalent to 24 percent of our total national coal reserve on a tonnage basis and 15 percent on a heating-value basis. Distribution and relative amounts of United States coal and lignite reserves are indicated in figure 1. By far the largest proportion of our lignite reserves, over 95 percent is found in North Central States, principally in North Dakota, South Dakota, and Montana, in the vast coal-bearing structural grouping designated as the Fort Union formation. Of the remaining United States reserves, all but a fraction of 1 percent are found in a series of relatively scattered deposits in Texas.

Jan 1, 1954

Rock property tests were performed on NX-size diamond drill core from the roof, floor, and coal from the longwall mining section of Federal No. 2 mine, West Virginia. The purpose of these tests was to determine the engineering properties of the various strata as part of a ground control study of the longwall operation. The following tests were performed: 1. Uniaxial compressive strength, Young's modulus, and Poisson's ratio 2. Triaxial compressive strength 3. Brazilian tensile strength 4. Modulus of rupture 5. Specific gravity Thirteen boxes of core delivered to the University on April 1, 1974 were identified as follows: 2 PTR 1 -2 boxes of roof rock 2 PTF 1 -2 boxes of floor rock 2 PTR 2 -2 boxes of roof rock 2 PTF 2 -2 boxes of floor rock with approximately 3 ft of coal in Box 2 (designated 2 PTC 2) 2 PTR 3 -2 boxes of roof rock 2 PTF 3 -2 boxes of floor rock 1 PC 5 -1 box of coal

Jan 1, 1976

By William W. Adams

A general increase in employment prevailed in the stone-quarrying industry of the United States during 1941 compared with 1940. Likewise, more accidents occurred to men working in and about the quarries, with the result that the accident-frequency rate for the industry as a whole was higher in 1941 than in the previous year. Reports from operating companies to the Bureau of Mines, covering open and underground quarries, as well as rock-crushing and rock-dressing plants, cement mills, and limekilns at or near the quarries, showed a total of 86,123 men employed and a total of more than 22 million man-days of labor performed during 1941. The total working time of the industry averaged 260 days per man. Measured in man-hours, the volume of work equaled 173 million, an average of 2,011 man-hours per employee.

Jan 1, 1943

By Donald Christofferson

This report documents the program conducted to demonstrate the application of a flywheel-powered propulsion system to underground mining shuttle cars. Such application can replace the present electrical trailing cable common to most shuttle cars and thereby eliminate those safety hazards, maintenance problems, and haulage route limitations inherent in the trailing cable. Described are the activities undertaken to specify and design a flywheel of optimum size, shape, and material; to identify the best concepts of input and output systems; and to achieve installation of the power package into a shuttle car. The resultant Flywheel-Powered Shuttle Car is an FMC Model 6L shuttle car, 6-ton capacity, 20-ton gross vehicle weight, powered by a flywheel system with 4.5-kilowatt-hour usable energy. The completed vehicle was delivered to the Bureau of Mines in Bruceton, Pennsylvania, for testing and evaluation.

Jan 1, 1986

The 1965 Lignite Symposium, the Louth in a series and the third sponsored by the University of North Dakota and the Bureau of Mines, was held at Bismarck, N. Dak., on April 29-30, 1963. These symposia provide a forum for those interested in the technology and utilization of solid fuels, especially lignitic coals. As part of the meeting, a 200-mile field trip was taken including; inspection of (1) the 200-megawatt, pulverized lignit-fired Leland Olds plant of Basin Electric Power Cooperative, under construction near Stanton, N. Dak.; (2) the site of the Glunharold mine of the Truax-Traer Coal Co., Division of Consolidation Coal Co., where a wheel excavator was being assembled; (3) the operating Beulah mine of Knife River Coal Mining Co., subsidiary of Montana-Dakota Utilities Co., near Beulah, N. Dak.; and (4) the 400-megawatt, hydroelectric Garrison Dam powerplant, near Garrison, N. Dak.

Jan 1, 1966

By William L. Crentz

Early in the nineteenth century, coal from Clearfield County entered the eastern commercial market. Ashley reports that coal was moved down the Susquehanna River by ark from Clearfield to Columbia, a distance of 260 miles, as early as 18o4. Around 1850, the famous Moshannon or Lower Freeport bed was discovered. Several years later the Moshannon Basin was developed extensively, and the coal from this area soon acquired an enviable reputation as a high-quality industrial fuel. Today much of the original Moshannon Basin coal is worked out, and the Lower Kittanning bed has replaced the Lower Freeport bed as the principal source of production in southeast Clearfield County. With depletion of the thick underground deposits, the importance 'of Clearfield County as a coal Producer would have diminished rapidly, if it had not been for strip mining the thinner beds. About 60 percent of the coal produced in the county is strip-mined, and the trend toward this mining method is expected to continue as the older underground operations are exhausted. Many strip mines are working in beds that are too thin to be recovered economically by any other method.

Jan 1, 1952

By O. H. Metzger

This is one of a series of capers being published by the Bureau of Mines on gold mining A the Western States. It describes the production of gold in the principal mining districts of New Mexico. The material was gathered red on a trip through tale State in the summer of 1936. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of mine operators in all parts of the State, who willingly contributed all information requested. Geological reports of the Geological Survey and the New. Mexico Bureau of Mince were drawn upon freely for information; credit to individual paper, is given in the text.

Jan 1, 1938

By R. E. Head

[This paper embodies the data obtained by a detailed statistical, microscopic analysis of the composite mill feed concentrate, and tailing from the Magne and Arthur mills of the Utah Conger Co. for 1 month in 1929. It is one of a series of papers by the same authors5 dealing with the mineralogical characteristics of the ore and concentration products from various well-known plants. The work was done in the cooperateive microscopic service laboratory at Salt Lake and represents the results of cooperation between the United States Bureau u of Mines, the Utah Copper Co. and the University of Utah.]

Jan 1, 1935

By A. Brown

This report details work performed and results obtained in a study of the water management aspects of oil shale mining and retorting in the Piceance Creek Basin. Three specific sites were investigated, and optimal water management systems for both conventional and in-situ extraction processes were generated. Water-related legal and environmental constraints on development were identified and the water management schemes were developed in compliance with these regulations. Limitations on shale oil production implied by limited water supplies were evaluated. Potential Basin-wide effects of development were evaluated using a computer model, and mitigation strategies were developed. Recommendations for additional investigation and analyses were presented.

Jan 1, 1977

By J. L. Henry

The development and status of technology for producing titanium from U.S. resource materials are summarized in this Bureau of Mines report. Commercially feasible processes and investigations of alternative procedures are reviewed in order to identify techniques that could make existing operations more effective or areas in which future research may lead to the development of new production methods. Procedures are described for producing concentrated titanium dioxide from starting materials such as sands, massive deposits, and mineral processing residues containing rutile, ilmenite, and perovskite; producing and purifying titanium tetrachloride from concentrated rutile, ilmenite, and titaniferous slags; reduction of titanium tetrachloride to titanium sponge metal using metallic magnesium or sodium; purifying and consolidating titanium sponge and scrap by arc melting or induction melting techniques; purifying sponge, scrap, and alloys by molten salt electrorefining; and electrowinning titanium from chloride salts.

Jan 1, 1987

By William W. Adams

The quarrying and related industries of the United States made a large gain in employment (man-hours of work) in 1942 with a somewhat smaller number of men employed than in 1941. This was accomplished chiefly by increasing the number of workdays per man and also by increasing the length of the workday. In spite of the greater volume of work performed, the industry had a more favorable accident-frequency rate in 1942 than in the previous year. Accident and employment reports from operating companies showed that the industry employed 84,270 men for an average of 271 days per man in 1942, with a volume of work of almost 181 million man-hours. The average workshift comprised 7.93 hours, and the number of man-shifts worked totaled nearly 23 million. Injuries from accidents in and about the quarries and plants caused disability to 6,461 employees, 112 of whom died as a result of their injuries, including 28 employees whose lives were lost in a single disaster. The accident-frequency rate in the industry was 35.73 per million man-hours worked, comparing favorably with a rate of 40.11 for the previous year. However, the figure for 1942 included a death rate of 0.62 per million man-hours which, because of the disaster referred to, was considerably higher than the fatality rate of 0.44 for 1941. Had the disaster not occurred, the fatality rate for the industry for 1942 would have been 0.46. The major disaster in which 28 lives were lost occurred on March 26 at the Sandts Eddy quarry of the Lehigh Portland Cement Co. near Easton Pa.

Jan 1, 1944