Search Documents

By E. F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged mechanical dust collectors (scrubbers) with high dust collection efficiency and low energy comsumption for controlling dust in coal mining operations. All of the scrubbers described are similar in configuration and are powered by 6-hp, 2,000-ft3/min vane axial fans. Air pressure differential is less than 6 inches water column. Height of the scrubbers? including fan is less than 14 inches, width is less than 16 inches, and length is less than 45 inches. The flooded fibrous-bed scrubber achieved respirable (less than approximatey 7 µm) dust collection efficiencies of 95 percent. The small-diameter-cyclone scrubbers showed about 92 percent efficiency and can be best where excess water is a problem. The wetted brush scrubber showed 88 percent efficiency at low cost, and the wetted fan scrubber showed a slightly lower efficiency (87 percent) but offered the smallest size and cost. A suitable water droplet eliminator is described.

Jan 1, 1978

By H. C. Ko

Calorimetric determinations of low-temperature heat capacities and the standard enthalpy of formation were made by the Bureau of Mines for aluminum sulfide, A12S3. The standard entropy (S°), enthalpy of formation (?Hf°), and calculated Gibbs energy of formation (?Gf°) at 298.15 K are 27.93±0.05 call deg-mole, -155.6±0.9 kcal/mole, and -153.0±1.0 kcal/mole, respectively.

Jan 1, 1976

By J. L. Ambs

The U.S. Bureau of Mines (USBM) Diesel Research Program emphasizes the development and evaluation of emission control devices to reduce exposure of miners to diesel exhaust pollutants. Studies by the USBM have shown that diesel exhaust aerosol (DEA) contributes a substantial portion of the respirable aerosol in underground coal mines using diesel equipment not equipped with emission controls. The USBM and the Donaldson Co., Inc., Minneapolis, MN, have developed a low-temperature, disposable diesel exhaust filter (DDEF) for use on permissible diesel haulage vehicles equipped with waterbath exhaust conditioners. These were evaluated in three underground, mines, to determine their effectiveness in reducing DEA concentrations. The DDEF reduced DEA concentrations from 70 to 90 pct at these mines. The usable life of the filter ranged from 10 to 32 h, depending on factors that affect DEA output, such 'as mine altitude, engine type, and duty-cycle. Cost per filter is approximately $40.

Jan 1, 2010

By J. T. Popp, C. M. McCulloch

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con- tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By Robert M. Becker

Part 5, the last of this series, deals with the theoretical confirmation and application of results developed in parts 1 and 2. The bulk-sampling variances of Hassialis and Kassel and Guy are compared with those in part 2, both as to formulation and as applied to ores and coal. The results provide confirmation for much of the development in part 2. Examples are presented for determining the reliability of bulk samples with respect to various measurable characteristics. These characteristics include, for example, assays for elements or compounds and particle surface area. The bulk samples considered consist either of a given weight, a given volume, or a given number of particles. In addition to problems of sample reliability, some of these examples may also be applicable to quality control. Several possible applications of results developed in parts 1 and 2 are outlined. These include tests for random data, degree-of-mixing indices, and particle-fineness indices.

Jan 1, 1966

By A. C. Richardson

[During the past two and a half sears the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators, have been making an extensive studs of coal preparation in the State of Alabama. Considerable time has been devoted to the studs of the washing characteristics of the Mars Lee bed and the various methods used In preparing from it a low-ash coal suitable for the manufacture of metallurgical coke. One of the phases of this problem is the utilization of middlings products from the washing plants. This paper gives the results of treating jig middlings on a coal-washing table at the Bureau of Mines laboratory at Tuscaloosa, Ala. The sample used was secured from the Sayreton washery of the Republic Steel Corporation, Sayreton, Ala. WASHERY PRACTICE The Mary Lee bed is very bony, and operators find it difficult to produce from this bed a washed coal much under 10 per cent ash. Experience has shown that in the preparation of a coking coal from the Mary Lee bed it is best to use a process which permits the recovery of a middlings product. Middlings are desirable because separation according to specific gravity is never perfect, and a middlings product makes possible a low ash in the primary warned coal without excessive losses of combustible in the refuse. The general washery practice on the Mary Lee bed is to crush the run-of-mine coal through some maximum screen size and wash it upon some one type of jig without re-treatment of any of the products made. The maximum size treated varies from 3 inch to J inch. The middlings product from multiple-cell jigs is usually termed "boiler fuel" and when possible is utilized as such. At present the production of boiler fuel is often in excess of power requirements, and the surplus, due to its high ash content, becomes waste.]

Jan 1, 1931

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have long used stationary tapered element oscillating microbalances (TEOMs®) in laboratory settings. They have served to assess the mass concentration of laboratory-generated particulates in experimental , dust chambers and they provide a reference method for comparison with other particulate- measuring instruments. Current NIOSH research is focused on further adapting TEOM technology as a wearable personal dust monitor (PDM) for coal mining occupations. This investigation's goal is to help identify, quantify, and provide means for resolving certain TEOM- related error. The present research investigated bias caused by thermal effects on filter assemblies. New filters used in the PDM for 8 h tests show an average positive bias of 25.5 pg, while similar tests of equivalent filters used in two 1400A model TEOMs show an average positive bias of 34.3 µg. The derived bias values allow correction of previously collected biased data. Also, pre- heating the filters for 24 h at 46° C shows significant bias reduction, with PDM pre-heated filters subsequently averaging -3.3 µg and 1400A TEOM filters averaging 5.9 µg. On a single-point comparison to gravimetric sampling, a 25.5 µg bias is only significant at low mass loadings. At 2.5 mg, this bias represents a negligible 1 % of the mass measurement. If ordinary linear regression is used, the bias is still insignificant. However, if the more valid weighted linear regression is used, it gives more weight to the smaller dependent variable values, which are more impacted by the bias. Consequently, what is 1% bias on a single high-mass value can translate into a larger bias percentage at high-mass values when performing a weighted regression on data that include a large number of low-mass values.

By E. L. Garton

Michigan is becoming one of the important oil-producing States of the country. The amount of crude oil produced within its boundaries has increased from only 4,000 barrels in 19253/ to nearly 16 million barrels in 19935.4/ The Bureau of Mines method of crude-oil analysis and classification-indicates that the oils from the several producing fields are predominantly paraffin-intermediate-base, wax-bearing crudes. In general, they will yield 25 to 35 percent of highly paraffinic gasoline and about the t- me amount of kerosene and gas-oil combined, 7.2 to 15 percent of lubricating oil stock, and 20 percent of residuum with a carbon residue or about 6 to 7 percent. In addition, there appears to be some correlation between certain properties of the crude oils and both the geographical location and geological structure of the oil-producing areas within the State. These general conclusions are based on the analytical data presented in this report, which is one of a series of papers that record the general characteristics of crude oil from the many producing fields of the United States. This report discusses briefly the oil fields of Michigan and the characteristics of the crude oils produced from them. The analyses of 15 samples are given. These samples were obtained from 13 fields in 9 counties in the lower peninsula and represent crude oils produced from the Berea sandstone, Upper Traverse and Traverse limestones, and the

Jan 1, 1937

By Rustu S. Kalyoncu

Nonoxide ceramics with improved high-temperature properties could substitute for high-temperature alloys and reduce toe Nation's dependence on imports of Cr, Co, Ni, and Mn. To meet this objective, the Bureau of Mines conducted research to synthesize u1trafine reactive boron nitride (BN) powders BN powders were prepared at temperatures ranging from -75? to 750? C. Low-temperature reactions (-75? to 200? C) between boron halides and N compounds led to formation of e1emento-organic compounds that were thermally decomposed to u1trafine (approximately 100-to 150-A particle size) reactive BN powders. BN powders were also prepared through the reaction of a 10w-me1tinginorganic B compound (boric acid, borax) with an organic N compound (carbimide and thiocarbimide) in N2 and/or ammonia (NH3) atmospheres at temperatures between 500? and 750? C.

Jan 1, 1986

By B. W. Dunning

This paper describes studies conducted by the Bureau of Mines to achieve its goal of developing methods for increased recovery and utilization of valuable constituents in a wide variety of domestic and industrial wastes, In this particular study, 36 units of obsolete electronic equipment from military aircraft were disassembled into their modular components by hand to determine materials distribution. Further modular disassembly into individual parts was used to identify metal composition. After identifying the metals in some of the more difficult to dismantle modules, similar modules were grouped together, shredded, mechanically separated, and using metal composition data from hand separation, classified along with the hand-separated materials. Although this equipment is normally classified as law-value iron-bearing aluminum, data were obtained that indicated the potential for moderately higher value classification. The electronic units were classified as to precious metals, copper, iron, and aluminum contents, and scrap values were estimated.

Jan 1, 1980

By Joan C. Biordi

The Bureau of Mines used molecular beam-mass spectrometry to determine the microstructure of a 10.1% CH4-2l.2% 02-67.6% Ar-1.1% CF3Br inhibited flame and its uninhibited analog, both stabilized at 32 torr on a cooled flat-flame burner. Composition profiles of atomic, radical, and stable species and temperature profiles for both flames were obtained and compared. Kinetic analyses of the profiles yielded values for the rate coefficients of several elementary methane flame reactions and information on the reactions of formation and decay of the observed halocarbon species. CF3Br is judged to decay by thermal decomposition as well as by abstraction reactions, and the fluorocarbon chemistry occurring in the inhibited flame is due primarily to CF2 radical reactions. Rate coefficients and mechanisms for reactions of the inhibitor-related species are given.

Jan 1, 1978

By Ellis S. Hertzog

The data published in this retort cover only one phase of a special study of tile physical and chemical properties s of only Alabama coals made by the Bureau of Mines. In addition to determinations of friability, the survey included determinations of grindability, B.t.u. value, and ash-fusion temperature. Assay distillation tests, both for high- and low-temperature carbonization, and proximate and ultimate analyses were made also. However, this preliminary paper is concerned only with the results of friability tests and is issued to expedite the release of this information to the public. The friability, test measures the liability of a coal to break into smaller pieces when subjected to repeated handling, as occurs in the mining, preparation, and transportation operations. Friability depends on many physical characteristics of the coal that vary not only between different seams but also in the same seam. The laboratory methods of determining friability have been developed to give a practical means of estimating degradation of size. So far as is known to the authors, no data on the friability of Alabama coals have ever been published. This caper makes available for the first time fairly comprehensive3 information on this subject. Because the procedure for the tumbler test for determining the friability of coal is relatively new to the coal operators, the authors Lave included a, complete description of it in this report.

Jan 1, 1938

By R. G. Sandberg

Many gold-bearing ores throughout the Western United States contain small quantities of mercury. The presence of mercury not only decreases the gold-loading capacity of the activated carbon, but complicates the fire refining of cathodes and creates a potential health hazard. The Bureau of Mines investigated methods to limit mercury extraction during gold ore leaching and to remove mercury from cyanide leach solu-tions. Mercury dissolution was reduced from 40 to 10 pct by decreasing NaCN concentration from 20 lb to 0.34 lb per ton of solution at a pH of <11. When 0.1 lb CaS per ton of ore was added to a leach slurry, mer-cury extraction was reduced from 27 to 0.4 pct. Less than 0.5 pct of the mercury was solubilized when <0.1 lb CaS per ton of are, along with lime and NaCN, was added to a simulated grinding circuit.

Jan 1, 1984

By George T. Faust

The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the various types of clays to be found in the Southern States. In connection with this work, the petrographic laboratory is called

Jan 1, 1940

By James C. Cawley

This paper updates an earlier report by the authors that studied electrical injuries from 1992 to 1998. The previous information is expanded and supplemented with fatal and nonfatal injury rates and trends through 2002. Injury numbers and rates were used to compare and trend electrical injury experience for various groups and categories. This information allowed identification of at-risk groups that could most benefit from effective electrical safety interventions. The data presented in this paper are derived from the U.S. Labor Department?s Bureau of Labor Statistics? Census of Fatal Occupational Injuries, Survey of Occupational Illnesses and Injuries, and Current Population Survey. Between 1992 and 2002, 3378 workers died from on-the-job electrical injuries. Electricity remained the sixth leading cause of injury-related occupational death. From 1999 to 2002, 4.7% of all occupational deaths were caused by electricity, down from 5.2% in the 1992?1998 time period. The cause of death was listed as electrocution in 99.1% of fatal cases. Contact with overhead power lines was involved in 42% of all on-the-job electrical deaths. The construction industry accounted for 47% of all electrical deaths between 1992 and 2002 but showed overall improvement from 1995 to 2002 by reducing its electrical fatality rate from 2.2 to 1.5 per 100 000 workers. In addition, 46 598 workers were nonfatally injured by electricity. Contact with electric current of machine, tool, appliance, or light fixture and contact with wiring, transformers, or other electrical components accounted for 36% and 34% of nonfatal electrical injuries, respectively. Contact with underground buried power lines was involved with 1% of fatal injuries and 2% of nonfatal injuries. The research of the National Institute for Occupational Safety and Health aimed at evaluating commercially available overhead power line proximity warning alarms is described. This paper is expected to be the initial step for eventual development of a performance standard for such systems.

Jan 1, 2008

Workers at Anaconda Aluminum Company&apos;s primary aluminum smelter at Sebree, Ky., were back on the job December 1, after agreeing to a new 3-year contract. The old contract had expired November 15. On December 20, the Aluminum Company of America reportedly shut down a 42,000-ton-per-year potline at its Wenatchee, Wash., primary aluminum smelter and half of a 23,000-ton-per-year potline at its Vancouver, Wash., smelter as a result of a power cutback by the Bonneville Power Administration. A1 so in December, Kaiser Aluminum & Chemical Corp. reduced overall power at its Mead and Tacoma, Mash,, smelters and shut down one of eight 27,500-ton-per-year potlines at Mead. Reported shutdowns for the firms since September have amounted to 76,000 tons for Alcoa and 50,000 tons for Kaiser. Alcan Aluminum Ltd. announced plans to double the generating capacity at its Kemano hydroelectric power plant in British Columbia to 1,916 megawatts. The additional power would be equal to that required of a primary aluminum smelter with an annual capacity of 567,000 tons.

Jan 1, 1980

Provide the U.S. mining industry with a user friendly computer program to calculate stresses in underground coal mines in order to improve safety conditions for mine workers. Capabilities of MULSIM/NL MULSIM/NL (multiple seams, nonlinear) is a three-dimensional boundary-element method (BEM) program developed at the U.S. Bureau of Mines for stress and displacement analysis of coal mines. It can analyze one or two parallel seams that can have any orientation with respect to the Earth&apos;s surface. Three main new features distinguish MULSIM/NL from its predecessors: (1) non¬linear material models, (2) multiple mining steps, and (3) energy release and strain energy computations. MULSIM/NL has six material models for the in-seam material: (1) linear elastic for coal, (2) strain softening, (3) elastic plastic, (4) bilinear hardening, (5) strain hardening, and (6) linear elastic for gob. The multiple mining step capability enables the user to efficiently simulate a changing mine geometry. Finally, MULSIM/ NL computes energy release rate due to mining using the most recent concepts advanced by Salamon.

Jan 1, 1993

By Wing G. Agnew

[This report presents the results of tests made by the Mining Division, Bureau of Mines, on the relative durability of manganese-steel drill rods and carbon-steel drill rods for use with detachable bits.]

Jan 1, 1941

By Arthur M. Hartstein

The Bureau of Mines through contract with Ultrasystems, Inc., obtained gram per gram data of products formed on thermal oxidative degradation of selected compositions, both under dynamic and static conditions. Four broad classes of materials were studied! Polyvinyl chloride compositions, neoprene compositions, rigid urethane foams, and variously treated woods. Whenever possible, comparisons between pure components and composites were attempted. Thermogravimetric and differential thermal analyses were performed to gain understanding of the processes occurring and to explore the feasibility of using these analyses as a method of material identification. The toxic products detected and quantitated included HC1, H2S, CO, S02, CS2,COS, HCOOH, CH3COOH, formaldehyde, acrolein, C 6H6, chloroprene, chloroethanol, benzyl chloride, aniline, and furfural.

Jan 1, 1974

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964