Search Documents

By Richard A. Thomas, Michael J. Sapko, Gary L. Mowrey, William D. Monaghan, Michael A. Trevits

Over the years, more than 20,000 mine seals have been erected in underground coal mines in the United States. Seals are used extensively in underground mines to isolate worked-out areas, active mine fire zones, and to control water inundations. Seals are most often built directly in the mine and can be fabricated from blocks made of wood or cementitious material. Recently, several explosions occurred within sealed areas of underground U.S. coal mines. These explosions, believed to be initiated by lightning strikes on the surface, destroyed numerous seals and caused considerable damage external to the sealed area. The National Institute for Occupational Safety and Health is conducting research to develop design guidelines, to investigate noninvasive techniques to characterize seal strength properties, and to evaluate seal test methods. As part of this work, a 30-ft wide, 16.1-ft tall and 4-ft thick seal was built in an underground experimental mine using cement and foamed water. Two types of noninvasive techniques are currently being investigated, namely the Schmidt Hammer for measuring compressive strength and ground penetrating radar (GPR) for detecting the presence of anomalies (e.g., voids, discontinuities) within the seal. Once these noninvasive tests were completed, the seal was subjected to destructive explosion testing. This study presents the results of the Schmidt Hammer tests, GPR scans, and the characteristics of seal failure during explosion testing.

By M. G. Zabetakis

Benzene and toluene are the first two members of an important homologous series whose general formula is CnH2n-6. The members of this series differ in composition from benzene by some integral multiple of CH2; they can all be prepared in the laboratory by the Wurtz-Fittig, Friedel-Crafts and Grignard syntheses. Because 'of the industrial importance of these-hydrocarbons, the limits of flammability of eight members of the series have been determined at 100° C.-(A temperature of 1000 C. was chosen because the determination of the upper limit of flammability of p-cymene requires an apparatus temperature. of at least 90° C. As elevated temperature data are available for other combustibles at 100° C. but not at 90° C., all data were taken at 100° C. in order to obtain comparable results.) Minimum ignition temperatures of these combustibles have been determined at laboratory-pressures.

Jan 1, 1951

By A. J. Kraemer

This paper is the third and concluding report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relative to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 3129.7 The second report dealt with the data of the twenty-third survey in accordance with the revised specifications for United States Government Motor Gasoline. These data were published as Report of Investigations 3142.8

Jan 1, 1931

By M. Shamsuddin

Information on total estimated uranium reserves and domestic requirements have been collected, A survey has been made on the possibilities of recovery of uranium from low grade and complex ore deposits, e.g., marine phosphorites, shales, coal, sea water, etc. In order to assess the potential for uranium recovery from uraniferous phosphorites, available thermodynamic data of uranium minerals, compounds and aqueous species have been collected. The existence of uranium complexes with chloride, fluoride, carbonate, phosphate, sulfate, etc., in ground waters have been evaluated at different pH's. There seems a great need to study the relative stability of these complexes in order to judge the applicability of solution mining technology for selective leaching of uranium from phosphorites. A typical flow-sheet demonstrating recovery of uranium from wet-process phosphoric acid has been included in this report. Some essential features of the economics of uranium recovery from uraniferous phosphorites have been briefly considered and recommendation have been made for further studies.

Jan 1, 1980

By R. E. Heithecker

In June 1933 the Bureau of Mines, in cooperation with the State of Oklahoma and the Oklahoma City Chamber of Commerce, published a report of the gas at reserves in the Oklahoma City oil field3/ based upon data as of October 1932, at which time there were 43 classified gas wells in the field, The estimates were obtained by the ?porosity-area" method. There are two general methods of estimating natural-gas reserves. The porosity-area method, as used by Hill and Rawlins, is used when a gas field is comparatively new but after enough drilling has been done to determine the average thickness, porosity, and areal extent of the producing horizon. The "pressure-volume? method of estimating gas reserves, the method used in this report, nay be used after a sufficient volume of gas has bean withdrawn from the reservoir to cause an appreciable decline in reservoir pressure.

Jan 1, 1937

By William J. Karwoski

To improve rock-burst control in deep vein mining, a field demonstration has been carried out by the Bureau of Mines to test a new rock-burst control concept--rock preconditioning in advance of mining. The procedure is to fracture the major rock-burst-prone zone during the development of each level before production mining. This allows initial mining to begin in a preconditioned zone and later mining from the level below to end in a prefractured or preconditioned pillar zone that is relatively burst-free. This full-scale field demonstration was carried out On the 7700 level of the Hecla Mining Co.'s Star-Morning mine. An expected burst-prone zone along the main vein between 7 and 10 crosscuts, some 250 feet long by 40 feet above and below the level, was preconditioned by blasting a fanlike ring of drilled holes from each crosscut. The drill holes, up to 100 feet long and 4 inches in diameter, were loaded with high explosives and shot. About 4,550 feet of drilling and 9,000 pounds of explosives were involved in the effort. Comparison of preshot and postshot data from monitoring instrumentation indicated that the blasting did fracture the rock in the planned zone and did result in an immediate stress decrease and softening of rock. The field data compared favorably with predicted results from a finite-element computer model simulation of the destressing. Based on observations made during mining and on the data from the Hecla rock-burst monitoring system, there is no doubt that this preconditioning in advance of mining demonstration resulted in much-improved rock-burst control during first-floor mining. It was also concluded that preconditioning the vein was more effective than preconditioning the wall rock.

Jan 1, 1979

By Donald F. Reed

In its investigation of old, abandoned, lead-zinc mines at which records of operations are not available, in 1914 the Bureau of Mines dug surface trenches anti', in 1947 It diamond-drilled three holes at the Albright Farm deposit in Sinking Valley. Some good lead-zinc ore had been extracted from veins in dolomitic limestone during the time of the American Revolution and as late as 1870. Since that time the only activity was sporadic prospecting and developing. Thu Bureau of Mines disclosed two additional veins by surface trenching, but diamond drilling failed to find significant lead-zinc mineralization.

Jan 1, 1949

By George A. Savanick

The U.S. Bureau of Mines has patented and transferred to industry an abrasive-enhanced water-jet rock drill. This drill incorporates three novel components: a collimator, jet deflectors for cutting clearance, and an unpressurized swivel, which rotates at 1,000 rpm while passing 20 gpm of an abrasive slurry flowing at 1,000 ft/s. Drilling occurs through the action of a 10,000-psi, 2O-gpm water jet into which is entrained 72 lb/min of abrasives. The pumps, hoses, and fittings are those commonly used in the water-jet-cleaning industry. Only inexpensive, common sandblasting abrasives are used. This drill can cut through hard rocks with moderate-pressure jets; e.g., rocks with a compressive strength of 73,000 psi can be drilled with a 1O,OOO-psi abrasive jet. In addition to drilling holes, the drill can cut deep, narrow kerfs; collar a hole at any angle; drill through rubble; and chamber holes. The development of the abrasive jet drill is a significant advance in the state of the art of hard-rock drilling. The Government of the United States has licensed the abrasive jet drill patent to Weatherford Water Jetting Systems.

Jan 1, 1989

By W. D. Riley

The U.S. Department of the Interior, Bureau of Mines, has been conducting minerals recovery research in support of the nation's geothermal program since 1974. The Bureau's program of laboratory and field studies has focused on determining the materials of construction for geothermal resource recovery plants and an the recovery of mineral values from the geobrines. An analytical program has been conducted at the Avondale Research Center to determine the chemical constituents of some high- and low-salinity geobrines found in the Imperial, Valley of California. Data are reported for the early stages of brine production of femur geothermal wells--the low-salinity, medium-enthalpy brines from the East Mesa Known Geothermal Resource Area (KGRA), Mesa 6-1 and 6-2, and the high-salinity, high-enthalpy brine from the Salton Sea KGRA, Magmamax 1 and Woolsey 1. The reported results indicate the importance of the operating and engineering history, the operating parameters during sampling, and the method of sampling in order to evaluate the chemical analyses.

Jan 1, 1980

By B. D. Sartwell

Multiple-charged beams originating from a 300-kv ion accelerator are important tools in the study of metal surfaces and thin films. A knowledge of the particle range is necessary for an understanding of the interaction processes of the ions with the targets. Utilizing a theory developed by Lindhard for determining the range of low-energy ions in solids, the ranges of H, He, C, N, 0, and Ar ions in A1203, Al, Fe203, Fe304, CuO, Cu20, Fe, Cu, Sn, and W were calculated for the energy range 60 to 400 kev using a computer program written in BASIC. The range, presented in graphical form, is given in both µg/cm2 and angstroms. In addition, heavy ion ranges were calculated for comparison with published experimental values. For ions with Z > 5, the discrepancy between the calculated values and published experimental values generally ranged from 2 to 40 percent; the largest deviations were probably due to experimental error.

Jan 1, 1970

By B. W. Madsen

Research by the Bureau of Mines has shown that treatment of open pit waste by crushing and sizing followed by flotation of the fines and leaching the coarse fraction results in greater metal recoveries than obtained by leaching only. Tests with a chalcocite-bearing quartz monzonite mine waste sample that had been crushed to minus 6 inches and screened on 1/2 inch yielded copper and silver recoveries of 71 and 22 percent, respectively, by the combined flotation-leaching process, compared with 48 percent of the copper and no silver recovered leaching the run-of-mine material. Copper was more readily leached from the coarse material with the minus 1/2-inch fines removed than from material with the fines included. The improved leaching was attributed to improved permeability and the associated improved circulation of air to the interior of the ore column. Cost estimates showed that the proposed intensive treatment of mine waste will require a greater capital investment and higher annual operating costs than conventional milling and dump leaching process. However, the income from the additional metal production offsets the increase in capital investment and operating costs, resulting in additional profit.

Jan 1, 1975

By Thomas R. Bur

This method of performing general transformations by use of Eulerian angles greatly reduces the time required for the determination of values for the elastic compliance constants (sij), elastic stiffness constants (cij ), Young's modulus, shear modulus, or Poisson's ratio for any orientation the cartesian coordinate system in an anisotropic material.

Jan 1, 1969

By T. W. Johnson

One of the common methods of increasing recovery of oil from partly depleted oil sands is to inject natural gas, air, or air-gas mixtures into the sand, thereby supplying energy to move oil. into the well bore. Where natural gas is not available, air or an air-gas mixture is used as the repressuring medium. Air-gas mixtures are obtained from the casingheads of oil-producing wells in the areas repressured with air or air-gas mixtures and consist usually of varying amounts of the hydrocarbon gases, nitrogen, oxygen, and carbon dioxide. Laboratory experiments have been conducted by the Bureau of Mines to determine the effect of air on crude oils.4/ In these experiments the crude oils were oxidized by the air, and the degree of oxidation depended not only upon the chemical composition of the crude oil but also upon the duration and method of contact between the oil and air, the temperature of the fluids and the concentration of the oxygen. When the crude oils were oxidized the following results and changes in the oils were obtained:

Jan 1, 1937

Develop and demonstrate a lightweight material that has low thermal conductivity and that would be suitable for placement using shotcrete methods. This material could be applied in deep, hot mines where mine drifts must be insulated. Its use would decrease mine refrigeration needs and reduce energy costs.

Jan 1, 1994

By R. S. Dean

This report, the third of a series of annual reports of the Metallurgical Division to be released in this form, covers the fiscal year July 1, 1936, to June 30, 1937. The technological work of the division is performed by sections. Thus, an efficient organization is provided to prosecute the various problems under investigation, and a logical system is set up for presenting the material contained in this report.

Jan 1, 1937

By Steven J. Page, William A. Heitbrink, Andrew B. Cecala, Edward D. Thimons, John A. Organiscak

Miners at noncoal surface mining operations are often exposed to high levels of respirable dust. In an effort to lower the respirable dust exposure of these surface miners, the National Institute for Occupational Safety and Health (NIOSH) has been conducting research to address this problem in a practical and economically viable manner. One successful effort deals with lowering the dust exposure of equipment operators in enclosed cabs. Many types of surface mining equipment utilize enclosed cabs to protect equipment operators from dust exposure. Normally when the equipment is new, the cabs are fairly airtight. These tightly sealed cabs, combined with good filtration systems, generally provide the operator with good dust protection. However, most mining equipment is older, and as aging occurs, many components of the enclosure deteriorate. The structural integrity of the cab diminishes and the effectiveness of the air filtration system fails. NIOSH has been successfully researching costs-effective methods to improve both filtration effectiveness and cab integrity of these older cabs in order to provide a healthier work environment for equipment operators. Dust sampling records indicate that drill operators and helpers have the highest dust exposure of all workers at surface mining operations. Since much of the overburden contains a high percentage of silica, the health hazard associated with this dust can be even more serious. NIOSH research is addressing techniques to lower respirable dust levels at surface drilling operations. INTRODUCTION NIOSH's mission is to assure a safe and healthy work environment for the working men and women of this nation. The primary emphasis of NIOSH's Pittsburgh Research Laboratory (PRL) is mining health and safety research. This report focuses on two areas of research

By J. W. Montoya

The chemical, mineralogical, and physical properties of berylliferous tuff from Spor Mountain, Utah, were determined in laboratory research conducted by the Bureau of Mines. Two beryllium-bearing minerals--a hydrated form of bertrandite and a berylliferous saponite--were found to be present in the tuff. Each of the beryllium mineral forms predominated in samples from certain areas of the district. The possibility of practicably separating the beryllium minerals from the tuff by physical methods appears remote because of the complexity and nature of the mineral associations. Beryllium mineralization in the region occurs in a rhyolitic tuff usually overlaid by unaltered rhyolite. The beryllium is distributed erratically throughout the tuff in individual mineralized bodies. Many samples of mineralized tuff were examined and found to contain from 0.2 to 1.8 percent BeO. All samples contained a hydrated form of bertrandite that was nearly cryptocrystalline, whereas samples from one area also contained a berylliferous saponite of variable beryllium content. Neither mineral has been previously reported, although related bertrandite-like minerals have been found in the U.S.S.R. and berylliferous minerals of the montmorillonite group have been synthesized. Most of the minerals of the tuff are finely crystalline, intergrown, and have similar densities. The complexity and intimacy of the mineral associations, the difficulty of achieving effective mineral liberation, and the highly friable nature are characteristics that lead to the conviction that tuff of the type examined cannot be effectively concentrated by gravity, magnetic, electrostatic, attrition, washing, sizing, or flotation methods.

Jan 1, 1962

By Paul McIlroy

Costs of producing lead from various known resources in the United States are developed by the Bureau of Mines to define the future availability of domestic lead at various price levels. It is estimated that 60 million tons of primary lead (75 percent of the total resource) is available at $0.20 or less per pound; 72 million tons (90 percent of the total) is available at $0.50 or less per pound; and the 79 mil- lion ton total estimated resource can be obtained at a price or $1.82 or less per pound. The supply available at $0.20 per pound or less will meet demand for over 78 years at the 1970 annual consumption rate of 763,000 tons.

Jan 1, 1974

By James H. Scott

Well-logging techniques that have been used to evaluate various types of mineral deposits are discussed briefly, and many pertinent references are cited. Information is categorized by mineral commodity to make it easy to determine what logging techniques have been used for evaluating specific metals and nonmetals. Part 1 discusses logging techniques applied to deposits of the following metals: aluminum, antimony, beryllium, boron, copper, iron, lead and zinc, maganese, mercury, nickel, silver and gold, tin, tungsten, and uranium. Part 2 covers the following nonmetals: coal, evaporites, fluorspar, oil shale, rock salt, and sulfur. Separate bibliographies are given for English and foreign language references.

Jan 1, 1974

By John P. Walsted

Because of the absence of an iron-producing industry, the Pacific Northwest is working under an economic handicap. This is particularly apparent in the gray-iron-foundry industry because of the high price of pig iron imported from foreign sources or shipped in from producing ?areas within the United States. The high prices and sometimes short supply of ferrous metal products has put a brake on industrialization, which has been only partly compensated by the availability of cheap electric power. The economic condition of the gray-iron-foundry industry could be improved by establishing a small iron-producing industry based on the locally available ores. Moreover, establishing a local iron smelter would create a market for resources now dormant. Low-grade ores of manganese, chromium, and nickel would become usable in industry when combined with the iron ore from Scappoose. Pig iron produced in even limited quantities would level out the fluctuation in supply. The ore deposits, being small, would not supply enough pig iron to satisfy the entire demand. This condition necessitates designing special pig irons that will carry abnormally high proportions of scrap in the cupola charge.

Jan 1, 1955