Search Documents

By H. Dolezal

A laboratory study of acid-ferrous sulfate treatment of low-grade manganese ores from the Cuyuna range, Minnesota resulted in 93-percent extraction of manganese as manganese sulfate with consumption of 3.8 pounds of H2S04 per pound of extracted manganese. Two types of ore were treated in consecutive stages. The first are contained carbonate minerals of manganese and iron, both soluble in H2S04 solution. The second ore contained manganese oxide minerals, insoluble in straight acid solution but soluble in the ferrous sulfate solution obtained from treating the first ore. Leaching data were obtained by countercurrent percolation of coarse (minus-1/2-inch) ore particles at room temperature and by agitating minus-65-mesh ore particles in heated solution. Extraction of manganese and acid consumption were the same, but the percolation leach required 6 days compared with 1 hour for hot agitation. Variations in the size of ore particles treated, leaching time, acid concentration, solution temperatures, and method of applying ferrous sulfate solution to the oxide ore were studied. The effects of several reagents for removing iron from solution and improving filtration were also studied.

Jan 1, 1959

By H. R. Babitzke

The purpose of this investigation was to evaluate the potential of columbium-hafnium alloys as structural materials for use at elevated temperatures. The work described in this report was conducted to determine the properties of columbium-hafnium alloys and to select the more promising ones for further improvement. Properties determined in this report were machinability, hardness, workability, tensile strength, and oxidation resistance. Ten ingots, ranging from 100 percent columbium to 70 atomic-percent hafnium, were prepared and subjected to tests. The test results showed that the alloys with 33 and 50 atomic-percent hafnium were superior in workability, strength, and oxidation resistance. For the alloy series tested, the strength and hardness values increased with the increasing hafnium content. Maximum values were reached with 50 atomic-percent hafnium. The oxidation resistance was poorest at the 1 atomic-percent hafnium level but improved with increasing hafnium content through 70 atomic-percent. Eight of the ten ingots were fabricable at room temperature. The two remaining ingots, those with 5 and 10 atomic-percent hafnium, required hot-working.

Jan 1, 1962

This Bureau of Mines investigation addressed two primary issues of air velocity measurement in mines: the determination and use of correction factors, and the development of guidelines for the selection of a suitable site at which the measurements should be taken. Other facets of the investigation included a comparison of measurement methods and devices, and aircourse cross-sectional area measurement. The study consisted of theoretical, laboratory, and in-mine investigations. The measurement devices included in the experimental phase were vane anemometer, vortex shedding anemometer, a prototype thermoan-emometer, smoke tube, and oil of wintergreen sprayer. The measurement methods included single-point centerline, timed-point traverse, continuous traverse for the anemometers, and various distances and cloud positions for the smoke tube and oil of wintergreen devices. The study resulted in guidelines for measurement site selection that are applicable to most inmine situations. It also showed that the use of correction factors is problematic. There are many potential pit-falls and there are cogent arguments against using certain correction factors. However, generalized correction factors were developed that can be successfully applied in routine ventilation work, provided that their use is properly understood.

Jan 1, 1985

By J. W. Paul

This circular is one of a series of papers4 on coal-mining methods and costs which are being prepared through the sponsorship of the U. S. Bureau of Mines for the purpose of presenting information on present mining methods and certain features which govern costs, safety, and conservation. The methods employed are influenced by natural local conditions with respect to the thickness, character, and dip of the coal bed, the nature of the roof and thickness of the overbearing strata, and the means employed for roof support and its control.

Jan 1, 1929

By R. V. Higgins

A computer program is presented to calculate the shape factors and volumes of cells from a potentiometric model, using coordinates of the inter-sections of the stream lines and equal potentials and a few additional coordinates. Shape factors are used in flow computations when the geometry is complicated. The program also includes computer instructions to divide the channels into cells of equal volume and to obtain the shape factor for each of these equal volume cells. An illustrated example using the potentiometric model for the waterflood of a seven-spot well-spacing pattern is presented. The information contained in the report is of value not only to those allied to the subject but also to others, because many of the techniques can be conveniently used in formulating other computer programs.

Jan 1, 1966

By Frank J. Wiebelt

In its efforts to maintain production of tungsten during the recent war period, the Bureau of Mines explored certain parts of the properties of the Atolia Mining Co. in San Bernardino County, Calif., by diamond drilling. Owing to past production record and other available data, the area was considered attractive for possible development of new ore bodies. Scheelite occurs in narrow veins ranging in width from a fraction of an inch to several feet. The veins are in quartz monzonite in a zone 2 miles long and 500 feet wide. Production from the district was reported to have been over 1,000,000 units of W03. Twelve diamond-drill holes, totaling 5,056 feet, were drilled by the Bureau of Mines in the vicinity of the Papoose, Papoose No. 5, Amity, and Union mines, the tailings pond, and the "Old Spud Patch." The work began in August 1943 and was completed in June 1944. This publication briefly describes the history and deposits of the district and gives full details of the work performed by the Bureau.

Jan 1, 1950

By J. E. Hamak

This publication contains analyses and related source data for 151 natural gas samples from 19 States. Of the total samples, 138 were collected calendar year 1989. The remainder were collected earlier, but releases to were not received until 1989. All samples were obtained and analyzed as part of U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1990

By Berenice B. Mitchell

THE STATISTICAL tables in this chapter present, country by country, the mineral production of the world in 1949-50. The figures are on a mine basis, unless otherwise indicated, except for cement, coke, and steel, which are measured at the processing plant. The tables are essentially a retabulation, by countries, of the 53 commodity world tables appearing in the various chapters of this volume. For lack of comprehensive information, data for the following minerals are excluded: Andalusite, aplite, asphalt, boron, bromine, calcite (optical), calcium chloride (natural), carbon dioxide, clay, columbium (niobium), diatomite (kieselguhr), dumortierite, emery, garnet (abrasive), gem stones (other than diamonds), germanium, greensand, grindstones, helium, indium, iodine, kyanite, lithium, magnesium compounds (other than magnesite), meerschaum, mineral pigments, monazite, natural gas, natural gasoline, oil shale, olivine, perlite, pumice, quartz crystal, radium, sand and gravel, selenium, sillimanite, sodium salts (other than common salt), stone, strontium, sulfur (byproduct), tantalum, tellurium, thallium, topaz (industrial), tripoli) uranium, vermiculite, wollastonite, and zirconium. In addition, a few minor geographic areas for which no statistics are available, are also omitted from the tabulation; it is believed that no significant quantities of minerals are mined in any of these areas. The statistics in these tables were derived principally from questionnaires sent, in cooperation with the United States Department of State, to the governments of each country. Supplementary sources were United States consular reports, the Imperial Institute's Statistical Summary of the Mineral Industry of the British Commonwealth and Foreign Countries, other official publications of various countries, the United Nations Statistical Yearbook, the Year Book of the American Bureau of Metal Statistics, Minerais et Metaux, business magazines, and company reports. Where official data were not available, esti-

Jan 1, 1953

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"An electro-optical method was used to quantify superoxide (SO) release from single rat pulmonary alveolar macrophages (PAM) exposed in vitro to respirable quartz and kaolin dusts and in vivo to quartz. Release was determined by measuring the reduction of nitroblue tdrazolium (NBT) to a diformazan precipitate at 550 nm from video-recorded images of individual cells. In vitro exposure to 0.025 or 0.05 mg/ml kaolin for 40 minutes resulted in no significant differences in either the total diformazan produced (max) or the maximum rate of diformazan production (R)./n vitro exposure to 0.025 mg/ml c1uartz decreased max 38 percent while no significant change was found using 0.05 mg/ml. However, R was decreased 31 percent and 24 percent for the low and high dose, respectively. In contrast, PAM obtained from animals exposed in vivo to quartz dust for two or four weeks in inhalation chambers exhibited increased production of diformazan. However, only PAM analyzed three days post-exposure showed significant increases, while PAM from animals sacrificed ten or 31 days post-exposure were not significantly different from control. The combined in vitro and in vivo quartz results might suggest that there is an initital acute response to exposure that decreases the ability of PAM to produce SO, followed by recruitment of production of PAM with increased SO producing capability. It appears that removal of animals from the source of exposure permits PAM to return to control levels of SO production by31 days. Whether this would be true for chronic exposure remains to be elucidated.IntroductionPulmonary alveolar macrophages (PAM) protect the lungs by phagocytizing foreign debris and bacteria.(1) This process involves ingestion as well as destruction of foreign matter. Phagocytosis usually is accompanied by a respiratory burst which increases cellular oxygen consumption leading to the release of highly reactive oxygen metabolites.(2) These agents have been implicated in the killing of bacteria by phagocytes, but they have also been shown to be toxic and,have been linked to cancer, emphysema, arthritis, diabetes, and other diseases.(3) Toxic effects may be a result of 1) an abnormally low production of metabolites, resulting in damage to lung tissue by the respired bacteria and/or dusts; or 2) an abnormally high production resulting in direct damage to lung tissue by metabolites themselves."

Mar 1, 1989

By James P. Bennett

The Bureau of Mines investigated the effect of refractory oxide additions, introduced in soluble form, on the high-temperature properties of 90- and 98-pct-MgO brick. Brick samples were soaked in solutions containing Al, Ca, Cr, Co, Fe, Mg, Mn, Mo, Ni, Si, Sr, Sn, Ti, or Zr ions. Additions to 98-pct-MgO brick did not generally result in statistically significant property improvements. Statistically significant improvements were noted in hot modulus of rupture (MOR), slag resistance, and spalling resistance of the 90-pct-MgO brick for additions of Al, Mg, or Sn. High-temperature performance of treated 90-pct-MgO refractories was equal to or approached that of 98-pct-MgO brick. The marked improvements due to tin were obtained with additions of only 1.14 wt pct Sn02.

Jan 1, 1985

By Richard Havens

Acidic and basic uranium leach plant residues located on the Navajo Indian Reservation, Tuba City, Ariz., were successfully stabilized against wind erosion using a relatively low-cost chemical method. An elastomeric polymer chemical was applied to the dike areas and a calcium magnesium lignosulfonate to the beach areas of three tailings ponds. The water-soluble chemicals were applied with an automated sprinkling system. The stabilization cost was $335 per acre for the 34.5-acre tract.

Jan 1, 1969

By L. J. Kane

While analyzing synthesis gas produced from coal, the Bureau of Mines found that conventional procedures for naphthalene determination were difficult and time consuming. The Bureau developed a rapid and sensitive turbidimetric procedure, which requires only simple instruments and hence can be used in plant-control laboratories. The gas is passed through a saturated aqueous solution of picric acid at 3° to 4° C. whose turbidity is then measured at room temperature. A dispersing agent is added to prevent coagulation of the suspension on warming. Only about 1 mg. (0.015 grain) of naphthalene need be absorbed, and precision and sensitivity are a few ten-thousandths of a grain, or a few hundredths of a grain per 100 cubic feet. The determination can be completed less than 10 minutes after absorption. INTRODUCTION One of the functions of the Branch of Coal Gasification, Bureau of Mines, Morgantown, W. Va., is to develop economical methods for manufacturing, from coal, a mixture of hydrogen and carbon monoxide for producing hydrogen, methane, and other gaseous fuels. This raw gas may contain many impurities, including naphthalene. This impurity is usually determined by first forming naphthalene picrate in a water solution of picric acid, separating the picrate, and titrating the unreacted picric acid or the picrate itself.

Jan 1, 1957

By D. Harrington

Although for many years considerable attention has been given to devising safe and efficient methods of using explosives, with some success, relatively little has been done to provide satisfactory storage facilities for them. This was known long before the present war began, but it was emphasized during the past 30 months? inspections of explosive magazines by employees of the Bureau of Mines in administration of the Federal Explosives Act of December 26, 1941. These inspections have revealed woeful in adequacy as well as definite hazards and the urgent need for obtaining better storage facilities either by remodeling old magazines or constructing ink new ones that would afford suitable protection for the contents against theft, fire, deterioration, and detonation. The purpose of this paper is to offer suggestions and to show by sketches and drawings some of the fundamental features of suitable magazines. Type of construction and available materials differ with different; localities, but the information herein contained can be applied to most magazines, whether already constructed or the construct: on of which is planned. It is hoped that this information will be helpful and will aid persons who are trying to provide suitable storage for explosives end detonators. It is also hoped that States and cities will be made aware of the unbelievable laxity practiced in storing explosives in the United States and will take some remedial action.

Jan 1, 1945

By J. C. Cawley, G. T. Homce, M. R. Yenchek, H. K. Sacks

As in many other industries, such as construction and agriculture, overhead electric power lines are a serious hazard at mining and mining-related operations. Even when excluding injuries that occur during electrical maintenance work, over one fourth of electrical fatalities in the mining industry are due to accidental overhead line contacts, and for each fatality nearly two serious non-fatal injuries occur due to such contacts. In incidents involving high-reaching mobile equipment, many of the victims touched the equipment after the fact, unaware that the machine frame had become energized by the line contact. MSHA data for accidents involving overhead power line contacts in the mining industry between 1980 and 1997 reveal that in 57% of the cases personnel were unaware of the accidental line contact until after one or more workers touched the equipment or a hoisted load and were injured. The situation is similar in the construction industry, where according to the National Institute for Occupational Safety and Health (NIOSH) data at least 20% of such victims are unaware of the line contact. This suggests that a device that alerts workers when a power line has been contacted could help prevent many of these injuries. Such a device would not prevent power line contacts, yet if widely employed could yield a significant reduction in the number of resulting injuries. Researchers at the NIOSH Pittsburgh Research Laboratory are attempting to develop such a device. The approach being investigated is based on measuring electric current flow to ground through a machine during a line contact. The specific technique being tested involves the diversion of some part of this current through a shunt cable mounted on board the machine, to provide a point at which to install a current sensor. Experiments thus far indicate that this approach is feasible. Ongoing research is better defining electric current flow through mobile equipment, refining techniques for measuring this current, and identifying factors that could limit the effectiveness of the proposed alarm.

By N. E. Hanna

Experience with the current version of gallery test 4, in use since 1913 to evaluate the incendivity of permissible explosives in the presence of coal dust, has shown the procedure to have inadequate discrimination. Consequently the Bureau of Mines used the up-and-down method of statistical design to investigate the incendivity of permissible explosives in the presence of coal dust and gas. A suitable device was developed to measure coal dust concentrations in the air-gas mixtures and to disperse the dust in the gallery atmosphere. A proposed testing method which uses suspended shots in a predispersed coal dust-gas-air mixture was evaluated. The new method can discriminate between different explosives with respect to their incendivity. Maximum ignitibility of the coal dust cloud by permissible explosives occurred in the vicinity of 0.3 oz/cu ft. About 10% sodium chloride in permissible explosive formulations had a very significant effect in reducing the probability of igniting coal dust. Bundled charges were more incendive than column charges.

Jan 1, 1966

By E. G. King

Low-temperature heat capacity determinations of the minerals goethite and pyrophyllite were made in the temperature range from 510 to 298° K. The entropies at 298.15° K were evaluated as 14.43 ±0.15 cal/deg mole for goethite and 56.6 ±0.5 cal/deg mole for pyrophyllite. The entropies of formation from the constituent oxides are -4.4 ±0.2 cal/deg mole for goethite and -12.3 ±0.6 cal/deg mole for pyrophyllite. The standard free energy of formation of goethite from its oxides is ?G°298.15 = 0.16 ±0.20 kcal/mole.

Jan 1, 1970

By R. F. Droullard

The Bureau of Mines has developed test facilities for use in a research program that deals with radiation hazards in mining. This report describes the radon test chamber located at the Denver Research Center and the Twilight experimental mine located near Uravan, CO.

Jan 1, 1984

Reduce spillage hazards and contamination when adding hydraulic nil to mining machine reservoirs. Approach An easily transported module, that delivers hydraulic oil directly into mining machines, was built and tested. How It Works The Hydraulic Oil Delivery Module is carried, from the oil storage area to the equipment needing oil, in the bucket of a scoop or other utility vehicle. Oil is pumped into the module reservoir from storage, or out of the module reservoir into the machine being serviced, through a long hydraulic hose. During long-term testing, the 115 foot long delivery hose made it possible to replenish the hydraulic oil in mining machines at the face with only limited interruption to the mining operation. (Figure 1 shows one! version of the module.) The compact Hydraulic, Oil Delivery Module consists of: an oil reservoir: a pump driven by a hydraulic motor; two high pressure, low volume oil lines, filters; and a low pressure, larger capacity delivery hose equipped with quick-connect-couplers. The high pressure oil lines are connected to the scoop's hydraulic power takeoff, which supplies the power to pump oil in or out of the module reservoir.

Jan 1, 1977

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C. 7 Emergency Rescue Hoists There is a need, especially in mine development areas, for portable, on-call, man-rated equipment capable of lifting men through several hundred feet. Wire rope climbing equipment as shown in Figure 37 appears particularly suited to this need. It is portable, weighing approximately 100 lbs. , is currently man-rated for numerous above ground applications and can be electric or air powered. Commercial units currently have a lifting capacity of 1000 lbs. , and can be fitted with bosun' s chairs. Lifting speeds are in the 20-30 FPM range and the equipment is not depth limited. In a situation where miners are unable to climb to the top of a shaft this equipment could rapidly be anchored to the top of the shaft and lowered to them by hand. Since the self contained unit is controlled by the person travelling in the shaft he would be able to negotiate shaft obstruction himself. This would not be possible with other forms of easily deployed free-hanging equipment. Typical manufacturers of this type of equipment are Ohio Hoist Mfg, Co, 321 South Beaver St. Lisbon, Ohio 44432 216-424-7283 Sky Climber Inc. 17311 South Main St. Gardena, California 90248 213-321 -6414

Jan 1, 1976

By E. L. Rawlins

Pipe lines through which natural gas is flowing should be buried in order to minimize fluctuations in the temperature of the gas, as these fluctuations have several harmful effects. One of these effects is to decrease the accuracy of measurements of gas volume. In order to meter properly the quantity of gas flowing past any point in a transmission system, it is necessary to how the temperature of the gas. If the temperature remains fairly constant, the gas flow can be measured with a close degree of accuracy, but if it fluctuates rapidly, close measurement is impossible.

Jan 1, 1926