Search Documents

By H. C. Carpenter

Data are presented comparing results obtained with 17 different catalysts in hydrogenating crude shale oil to gasoline in single-pass operation. A method is described for predicting the maximum yield of gasoline obtainable at constant pressure for each catalyst from results of a limited number of experiments at different temperatures. Operating variables have considerable influence on yields and properties of products. With most of the catalysts, at operating temperatures below 890° F. liquid yield exceeded 100 volume-percent. Above this temperature the volume of liquid product decreased rapidly. Maximum gasoline production in most instances was achieved at a temperature higher than that at which the maximum volume of liquid product was produced.

Jan 1, 1959

By W. M. Dressel

The Federal Bureau of Mines has obtained data by differential thermal analysis of the various minerals that represent the nation's resources in manganese. These data are supported by X-ray diffraction analysis, chemical analysis, mineralography, and optical mineralogy, and provide fundamental information on the response of each mineral to thermal treatment in oxidizing, reducing, and neutral atmospheres. The information can be applied advantage¬ously in the identification of manganese minerals. Its greatest potential value, however, lies in the application of the quantitative data on the reaction temperatures, rates, and products to the more efficient extraction of manganese from U.S. ores. Thermal analysis curves are presented for certain manganese minerals, namely hausmannite, bixbyite, braunite, pyrolusite, lithiophorite, cryptomelane, hollandite, manganite, rhodochrosite, and rhodonite. The original minerals and the products of their thermal decomposition were identified by X-ray diffraction analysis, supplemented by chemical analysis and mineralogical identification.

Jan 1, 1961

By J. D. Davis

"Introduction.Sixty years ago, M. Berthelot found that ethylene could be selectively absorbed from gaseous mixtures by concentrated sulphuric acid, and that the compound formed by the chemical union of the gas and acid was readily decomposed by heating with water, yielding ethyl alcohol. Only within the last few years has there been any attempt to make use of this discovery technically.Bury*, working in England at the Skinningrove Iron Works and on a commercial scale, developed a technical method for converting, the ethylene of coke-oven as into alcohol. With a gas containing less than 3 per cent of ethylene, he obtained a yield of 1.6 gallons of alcohol per ton of coal carbonized.De Loisy** perfected a technical method for treatment of coke-oven as for alcohol. Evidently this work was carried out on a semi-commercial scale. His method is based on the use of catalytic agents for hastening the absorption of ethylene by sulphuric acid. He uses part of the spent acid for drying the gases and pact for the manufacture of ammonium sulphate. Excess acid is reconcentrated by waste heat. Others have worked on the problem, but so far there has been no large recovery of ethylene from coke-oven gases. The chief difficulty seems to lie in the low efficiency (about 50% of methods and tae relatively low concentrations of ethylene in the gases treated. Gas from Trent amalgam*** contains much larger percantages of ethylene than does coke-oven gas, as Will presently be shown, and if it should ever prove practIcal to treat industrial ;as for alcohol, this gas would offer attractive possibilities,* Bury, Ernest, Ethylene as Alcohol from Coke-Oven Gas: Gas Journal' Vol. 148, D. 30, 1919, pp. 718.** DC Loisy, M.E., Sur un procede' industrial de fabrication syntlotique de l'alcool et de l'ether a partir des gaz de distillation de la houil Comp Rend, vol. 170, Jan. 1920, p. 50-3.*** A paste consisting of approximately part oil such as that obtained as for cleaning coal. See Perrott. in cleaning coal, Chem 3 parts finely pulvarized coal and 1 final product in the Trent, process StJ, and Kinney, S.P. The use of oil Vol. 35 August 3, 1921, p, 183.. & Met."

Nov 1, 1922

By Frank C. Morris

It is generally recognized that the productivity and ultimate recovery of an oil well may be reduced as a result of reduction in permeability of the sand at the well bore by invasion of filtrates and clay particles from drilling fluids. As a means of determining whether a sand has been "damaged" from these sources, several investigators2 3 4 5/ have developed methods of analysis based on the rate of increase in bottom-hole pressure while a well is shut in. Because of growing recognition of the importance of completion practices as related to the quantity of oil that may be recovered from wells, the Bureau of Mines has studied completion practices in California and the Midcontinent area. Well-interference and pressure-buildup tests were completed Ear seven wells in the Scurry Reef field to determine the effective permeability in the reservoir.6/ Also, a study was made of the pressure-decline curves obtained from 35 water-input wells in 5 different production areas of northeastern Oklahoma and eastern Kansas.7/

Jan 1, 1957

By D. D. Southworth

In 1981, 1982, and 1983, the Bureau of Mines examined the potential for lode deposits of platinum-group metals (PGM) in the Goodnews Bay ultramafic complex, Alaska. The complex consists of the Red Mountain, Suzie Mountain, and Smalls River ultramafic bodies and displays concentric zoning of rock types similar to complexes in southeast Alaska, British Columbia, and the Ural Mountains in the U.S.S.R. Results of the study indicate that platinum is preferentially associated with chromite and magnetite in the dunite core of the complex, and palladium is preferentidlly associated with sulfide minerals in the outer clinopyroxene-rich zones. the most promising targets for PGM lode deposits are the chromite-rich dunite at the heads of Fox Gulch and Squirrel Creek and iron-nickel and iron copper sulfide-bearing magnetite clinopyroxenite and hornblende-rich rocks outward of the dunite core, also in the Fox Gulch-Squirrel Creek area. Significant placer reserves are present in the unmined, deeply buried placer ground in the lower Salmon River Valley, and also in tailings from previous dredging.

Jan 1, 2011

By Donald J. Ninteman

This Bureau of Mines publication is a literature study of the problem of spontaneous oxidation and combustion of sulfides in underground mines. It summarizes the present-day hazards, process mechanisms, and prevention and control techniques of this growing problem in underground mines. The iron sulfides generally have the greatest tendency to oxidize, particularly pyrrhotite. The presence of moisture and oxygen is essential for the oxidation reaction. Highly fractured sulfides, when found with timber or combustible refuse in slowly circulating air, pose the most serious fire hazard. Quenching with water is effective in quickly dealing with local hot spots, but ventilation at high flaw rates is the most effective and economical means for long-term prevention and control.

Jan 1, 1978

By J. B. Clemmer

This report summarizes the results of u laboratory study of the beneficiation of Arkansas bauxite by flotation. Although the investigation is not yet completed, a preliminary retort of the results on several typical bauxites is presented to show the merits rind limitations of flotation for the production of concentrates acceptable to the aluminum industry. It is

Jan 1, 1941

By M. B. Boyer, C. H. Herty, F. A. Hartgen, G. L. Frear

"DEFINITION OF VISCOSITYViscosity has been defined as the resistance experienced by one portion of a liquid moving over another portion, such as one molecular plane moving over an adjacent plane. A measure of viscosity is the force required to keep one plane in motion at Unit velocity, the other plane being considered stationary. Figure 1 illustrates the general idea that the surface friction between two adjacent areas will be greater the larger the molecules. Therefore it may be assumed that viscosity will be increased by molecular association or agglomeration, and likewise dissociation rill decrease viscosity. According to Maxwell (1)6 the unit of viscosity, the poise, is the tangential force per square centimeter of area of either of two horizontal planes 1 centimeter apart, one of which is fixed while the other moves with unit velocity, the space between being filled with viscous liquid of unit viscosity.The need for a satisfactory apparatus and experimental procedure for the determination of viscosity of high-melting materials at temperatures corresponding to those in pig-iron and steel making has been recognized during the past few decades. The condition of the slag during the smelting and refining periods in the iron- and steel-making processes exerts an important influence on the metal product obtained, this slag condition really meaning the state of viscosity or, vice versa, fluidity, which the slag attains under certain conditions."

Jun 1, 1934

By H. J. Heinen

The Bureau of Milts studied repetitive batch electrowinning of molybdenum from molybdic oxide ) to determine the effects upon the electrolyte life, purity of metal product , and overall cell performance. The electrolyte consisted of 54.0 weight-percent sodium tetraborate (Na2B407), 23.6 weight-percent sodium chloride (NaC1), 14.9 weight-percent sodium fluoride (NaF), and 7.5 weight-percent Mo03. The feed materials were pure and technical-grade Mo03. Electrolysis was conducted at l,000° C in a graphite cell in an atmosphere of air and carbon oxides. Electrolyte degradation did not occur during repetitive winning of molybdenum from pure Mo03 in an 8-day (5,400-ampere-hour) period of operation. Electrowon metal contained <0.1 percent total impurities. The electrode configuration is a key factor in the direct conversion of technical-grade Mo03 to metal by repetitive cyclic electrolysis. The best configuration found was a cathodic crucible and a central anode. Metal purity of 99.8 percent and a current efficiency of 91 percent were maintained until the combined impurity buildup the electrolyte reached 4.7 percent silicon, l.0 percent aluminum, and 0.6 percent iron. One pound of molybdenum was produced per 1.5 pounds of solvent salts employed. About 25 percent of the initial NaCl and NaF contents of the electrolyte were lost owing to volatilization and crucible penetration.

Jan 1, 1966

By S. A. Ferguson

Purpose: Marras et al. developed a technique to evaluate sincerity of effort during dynamic trunk motion performance. The validity and reliability of the technique have not been evaluated. Therefore, the objective of this study was to first determine whether or not a sincerity of effort measure correctly identified those giving a sincere effort in a blinded randomized control trial and second to quantify inter-rater and test-retest reliability. Methods: This article reports the findings of a two phase study. In phase one, the blinded evaluation, participants were randomly assigned to either a sincere or insincere performance condition. An examiner tested participants without knowledge of the participant&apos;s group membership. In the second phase, two examiners evaluated each participant twice to quantify inter-rater and test-retest reliability. Results: In the blinded phase the specificity was 100% and sensitivity was 90% for identifying sincere and insincere effort, respectively. Phase two results showed no significant difference in probability of sincere effort between raters or between testing sessions. Conclusion: A performance criterion that accurately identifies sincere vs insincere group membership during functional evaluations was identified. There were no significant differences between raters or between testing sessions. These findings indicate that this test is reliable and possesses good predictive validity in assessing sincerity of effort.

Jan 1, 2003

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first papery dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second 6/ dealt with extraction in a mine (Crucible) in which coal was loaded by hand and in which the rib lines were long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central part of Washington County, Pa., approximately midway between the Montour 10 and Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalisations as appear to be justified.

Jan 1, 1940

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983

By O. Q. Leone

Excellent metal quality, with lower power requirement, is attained in electrorefining titanium by using internal heating of the fused-salt bath. An internal heater provides more effective heat utilization, simplifies structural components in cell design, and prolongs cell life by eliminating direct application of heat to the cell container. This Bureau of Mines report covers one phase of the research in progress at the Electrometallurgical Experiment Station at Boulder City, Nev., for improving the techniques and lowering the total power requirement for electro-refining titanium metal.

Jan 1, 1959

GLOSSARY TERM DEFINITION ACCOMODATION The process by-which the eye changes focus from one distance to another. ADAPTATION The process by which the retina adjusts-to more or less light then it was exposed to during an immediately preceding period. Also involved, to a lesser degress, is the change in the size of the pupil which regulates the amount of light entering the eye. Adaptation results in a change in the sensitivity of the eye to light. CENTRAL VISION (FOVEAL) The seeing of objects in the central or foveal part of the visual field. It is approximately two degrees in diameter and permits seeing much finer detail than does peripheral vision. DIRECT GLARE The effect of brightness or brightness differences within the visual field sufficiently high to cause annoyance, discomfort, or loss in visual performance. FOOT CANDLE A measure of the amount of light falling onto a surface. FOOT LAMBERT A measure of the amount of light that is being reflected by a surface. GLARE The effect of brightness or differences in brightness within the visual field sufficiently high to cause annoyance, discomfort, or loss in visual performance. LAMP A generic term for a man-made source of light. By extension, the term is also used to denote sources that radiate in regions of spectrom adjacent to the visible.

Jan 1, 1976

By Earl L. Hastings

Although the principal market for diatomite in the United States is in the East,4 production of the material is presently restricted to the West, because the deposits are larger, mining costs are cheaper, and the quality of product is better than that obtained from other domestic deposits. However, Tallahatta diatomite, occurring in Choctaw and Clarke Counties, Ala., has a freight rate advantage, which should encourage competition for those market that are now being supplied with the purer diatomites from the western deposits. For this reason, diatomite occurrences in the Tallahatta formation were examined by the Bureau of Mines and physical properties of samples from the deposit were determined to obtain additional data for use by any potential producer who wished to evaluate the material for its commercial possibilities. In 1894 K. M. Cunningham5 found that the buhrstone formation (now known as the Tallahatta formation) contained "siliceous shells of marine diatoms, radiolaria and foraminifera, thus being rather of the nature of tripoli or diatomaceous earth than of a true clay." Cooke6 and Semmes7 also reported the Tallahatta formation to be composed principally of diatomaceous earth with accompanying beds of sand, clay, and sandstone.

Jan 1, 1963

By C. E. Jordan

The Bureau of Mines conducted laboratory studies on methods to increase the recovery of brine from slime produced by operating potash plants. The slime was comprised of 80 percent brine saturated with KCl and NaCl, and 20 percent solids. A variety of settling techniques, filtration methods, continuous centrifugation, and novel processing techniques were investigated. Vacuum filtration recovered 6S percent of the brine at 47 gallons of brine per square foot per day. Pressure filtration, on the other hand, recovered 74 percent of the brine at 40.9 gallons of brine per square foot per day. Centrifugation in a 6-inch-diameter continuous decanter-type separator resulted in 42 percent recovery of the brine at a treatment rate of 542 gallons of brine per day. Vertical drains proved to be the most promising novel debrining technique investigated. With this method, 45 percent of the brine was recovered in 3 days.

Jan 1, 1977

By H. A. Doerner

From thermodynamic calculations3 Maier predicted that zinc oxide Land methane would react at specified temperatures substantially according to equation (1). (1) ZnO + CH; = Zn (gas) + CO + 2H2 Other reactions that may take place are: (2) CH4 = C + 2H2. (3) ZnO + CO = Zn (gas) + CO2 (4) ZnO + H 2 = Zn (gas) + H2O . Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C.

Jan 1, 1931

By T. E. Gray

This report describes the preparation characteristics of the signifi¬cant coalbeds in Preston County, W. Va. It is one in a series of reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 2 million tons of coal was produced in Preston County, W. Va. in 190, none of which was cleaned mechanically. Estimates as of January 1, 1959, indicate that more than 3 billion tons of coal remained in the county in beds 12 inches or more thick. The Bakerstown, Mahoning, Upper Freeport, and Upper Kittanning beds were selected by the Bureau of Mines for study based on current production and estimated minable reserves. Sample locations were selected after study of the literature, conferences with mining engineers and mining company offi¬cials in the field, and examination of available sites. Four samples were collected from the Bakerstown and Upper Freeport beds and one each from the Mahoning and Upper Kittanning beds.

Jan 1, 1961

By J. M. West

Increased leisure time and increased interest in the out-of-doors is leading more and more families to experiment with placer mining of gold, and some- times even to going on into small-scale production. This Bureau of Mines report supplies basic information un areas of occurrence, equipment needed, prospecting, sampling, mining, and regulations concerning the possession and sale of gold. Selected references are given for further study.

Jan 1, 1971

By Travis Q. Lyday

The Other South Pacific Island states extend from Palau, also called Belau, near the Philippines in the west, to French Polynesia in the east. However, a number of countries and territories have been omitted, from this chapter because their mineral production was insignificant to the local economy. These include the French over-seas territories of French Polynesia and Wallis and Futuna Islands; independent states, including Kiribati, Marshall Islands, Micronesia, Palau, Tonga, Tuvalu, and Vanuatu; the New Zealand freely associated state of the Cook Islands, and the New Zealand dependency of Niue. What mineral production existed in these islands was limited to construction materials such as coral reef limestone, crushed stone, and sand and gravel in minor quantities solely for domestic consumption. FIJI The mineral industry of Fiji continued to be dominated by gold, although this sector contributed less than 1 % to the gross domestic product (GDP) of the country. Gold and silver together ranked second in value among the country&apos;s exports. Fiji&apos;s economy contracted 11% during the 8-month period following the first, on May 14, of two military coups. Although the island nation had been a member of the British Commonwealth of Nations since its independence on October 10, 1970, Fiji&apos;s membership terminated with the emergence of the Republic or Fiji on October 15.

Jan 1, 1989