Search Documents

By Daniel E. Sullivan

This Bureau of Mines publication examines the potential impact on minerals of the tariff and nontariff agreements that resulted from the Tokyo Round of the Multilateral Trade Negotiations, which were conducted under the auspices of the General Agreement on Tariffs and Trade. These agreements will affect minerals by reducing tariff levels and by changing rules by which they are traded internationally.

Jan 1, 1981

At the end of August, U.S. producer posting of 99.5 percent unalloyed aluminum had been established at 48¢ per pound. At that time, dealer-quoted unalloyed ingot was reportedly at 44¢-47¢. CADMIUM: By late August, most U.S. producers had raised cadmium selling prices by 25¢ to $3 per pound. As a consequence, dealer quoting of cadmium ranged from $2.95 to $3.05 per pound. COAL: The wildcat strike, which began in southern West Virginia on July 19 and eventually spread to nine other States before ending on August 13, at its peak, idled approximately 115,000 miners and accounted for daily coal losses of an estimated 1.5 million tons at the height of the work stoppage. Concerned about the effects of the production cutbacks, the Bureau of Mines, early in the strike period, initiated its coal strike monitoring system which it had developed during the prolonged coal strike in the fall of 1974.

Jan 1, 1976

By Geoffrey C. Huggins

Diagnostic: tests were performed on a production ST-5A Load-Haul-Dump machine manufactured by Wagner Mining Machinery Company to evaluate and rank order noise sources. The diagnostic evaluation indicated that the major noise sources were the transmission, the engine, and the cooling fan. This phase was followed by implementation of recommended noise control treatments, which included vibration isolation of the transmission, a transmission enclosure, an engine enclosure, and modifications of the inlet to the cooling fan. The final step in the program was an underground operational period which began on 31 August 1976 at the National Gypsum Mine in Shoals, Indiana. The noise control treatments successfully reduced the LHD operator noise exposure by 7 dB(A), thus increasing its allowable operation time by a factor of 2.7. Actual measurements made underground using noise dosimeters have indicated that, during, a typical shift, the noise control treatments have reduced the fractional exposure to an allowable level. The report discusses the mechanical aspects of the LHD, its noise sources, the treatments applied, the final levels achieved, and field experience with the noise-controlled machine.

Jan 1, 1977

By S. C. Termes

The Bureau of Mines has used Fourier transform infrared spectroscopy (FT-1R) to study in situ reactions of aqueous solutions of potassium ethylxanthate with CU(II)-and Pb(II)-activated sphalerite plates, in which the plates were both the infrared-transparent windows and the reacting surfaces. A copper (I) ethylxanthate formed predominantly with Cu(II)-activated sphalerite, regardless of the activation time. The products formed on Pb(II)-activated sphalerite depended on the activation times; a short activation time (30 min) yielded a lead ethylxanthate-like product, but a long activation time (90 min) yielded a considerable amount of dixanthogen.

Jan 1, 1986

By Erle C. Donaldson

Bureau of Mines engineers examined the chemical and biological treatment of sewage water designed in one case for reuse and in another for subsurface injection. In the first case discussed, approximately 6 million gallons per day of sewage are treated by the activated sludge process followed by tertiary treatment that includes ion exchange. The renovated water is used in the industrial complex. Liquid industrial waste is sent to a waste disposal facility where it is treated for injection into a deep subsurface formation. In the second case, a community of 3,000 people is using a lagoon sewage treatment system followed by subsurface injection of t- treated effluent. Subsurface disposal is used to avoid growth of algae and weeds in a nearby lake to which the treated effluent was originally discharged. The renovation of municipal water for reuse provides a source of water for industries in a semiarid region and may also provide a source for domestic use in densely populated regions where domestic water requirements have priority over industry needs. In addition both waste treatment systems provide examples of the use of subsurface waste disposal to avoid pollution of surface streams.

Jan 1, 1971

By Lewis M. McNay

Description of methods employed and cost data are given for surface-mined land reclamation in Moraine State Park, Butler County, Pa. This project was conducted under the authority of the Appalachian Regional Development Act; a total of 177 acres of land was rehabilitated for specific land use purposes. The use of large equipment expedited the project work, and similar results could be anticipated on similar reclamation programs.

Jan 1, 1970

By J. Roger Loebenstein

Small amounts of arsenic trioxide were shipped in 1988 from remaining stocks at ASARCO Incorporated's closed plant at Tacoma, WA. Imports of arsenic trioxide were at about the same level in 1988 as in the previous year. Legislation and Government Programs The Occupational Safety and Health Administration (OSHA) levied a $1.6 million fine against Asarco for exposing its workers at its East Helena lead smelter in Helena, MT, to unacceptably high levels of lead and arsenic. The bulk of the fine was for violations of a respiratory protection program. The same smelter and its environs has been listed as a Superfund toxic-waste site by the Environmental Protection Agency (EPA). Tests had shown high levels of lead, cadmium, and arsenic in the soil near the smelter. EPA planned to extend the cleanup to areas within the town of East Helena because high levels of arsenic had been found in shallow test wells outside the smelter site. Federal and State health officials have warned residents living in the vicinity of East Helena to avoid eating certain home-grown vegetables because of high concentrations of heavy metals.2

Jan 1, 1990

By L. L. Rethi

The U.S. Bureau of Mines summarized injury data for independent contractor employees working at all locations of coal and metal-nonmetal mines from 1983 through 1990. During the eight years, the greatest contrast in degree of injury between independent contractor and operator employees was in fatalities. From 1983 through 1990, there were 132 independent contractor employee fatalities in the mining industry. In 1988 though, independent contractor employees accounted for nearly one-fourth of all mining fatalities. The fatality incidence rates of independent contractors were consistently higher than those of operators during the eight years. For instance, in 1990, the contractors' rate was twice that of operator employees in coalmining and nearly five times that of operators in metal-nonmetal mining. Three other salient facts highlight the independent contractor employees' fatality injury data during these years. First, 82% of the independent contractor employee fatalities occurred at surface locations. Second, two job classifications?truck driver and equipment operator?represented 37% of the fatalities throughout the 8-year period. And finally, four accident classifications?powered haulage, slips and falls, machinery, and electrical?accounted for 71% of all independent contractor employee fatalities.

Jan 1, 1993

By C. L. Brown

Coal has been transported by belt conveyors in mines for many years; however, only since the beginning of the general mechanization period have complete transportation system of this type been employed. Aside from my complete belt-conveyor transportation systems, belt conveyors are frequently used in conjunction with other transportation. Many early installations, for the most part, were made without standards as a guide. As a result, some States have outlined certain requirements based more or less on experience following mine fires. Correlation of these regulations should result in more uniformity in connection with standardization of regulations. The National Electrical manufacturers Association has published standards for mining-belt-conveyor installations2/ that should be helpful to the coal-mining industry generally. Bureau of Mines Schedule 2F3/ requires certain controls for permissible-belt- conveyor drives, and similar requirements are listed in Bureau of Mines bulletin 514.4/ Committees of the American Mining Congress have prepared much valuable information concerning operation of belt conveyors, and a subcommittee on fire-resistant belting has been active. 5/

Jan 1, 1956

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume n of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output!' It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1979

By A. E. Back

A method has been developed in the laboratory for successfully treating titaniferous magnetite ore from the deposit at Iron Mountain, Wyo. The ore is roasted with 15 percent sodium carbonate to convert the vanadium to a water-soluble form and fix the soda for the subsequent electric-smelting step. Approximately 90 percent of the vanadium is recoverable in a product assaying 80 percent V2O5. The leached calcine is briquetted and smelted in a graphite-lined electric-arc furnace. Substantially all of the titanium is recovered in a soda slag, assaying 60 percent TiO2 and 2 percent Fe, which can be upgraded to 75 to 80 percent TiO2 by leaching with dilute sulfuric acid. The upgraded slag could be utilized for the production of titanium dioxide pigments or titanium tetrachloride. About 90 percent of the iron is recovered as pig iron, containing only minor amounts of vanadium, titanium, and sulfur. The high TiO2 slag compares favorably with slag containing about 70 percent TiO2 being produced by the Quebec Iron & Titanium Corp. at Sorel, Quebec. The data obtained from this investigation indicate that a feasible process has been developed for treating Iron Mountain ore, and larger-scale testing is warranted to develop engineering data for the ultimate utilization of this deposit as a source of titanium, iron, and vanadium. There are adequate supplies of basic raw materials, electric power, water, sodium carbonate, coal, and petroleum products within fairly short distances of Cheyenne and Laramie, Wyo., the nearest cities and probable plant- and labor-supply points.

Jan 1, 1952

By Rogers F. Davis

The Bureau of Mines developed a new method for the determination of oxides of nitrogen in diesel exhaust gas. The procedure, a modification of the Saltzman method, uses a NO2 absorbent for the diesel exhaust gas; the colorless absorbent becomes purple on contact with N~. When used properly this procedure gives satisfactory results in 2 hours, whereas the standard phenoldisulfonic acid method required approximately 8 hours. The new method is not satisfactory for determination of oxides of nitrogen in the overrich fuel to air ratio range.

Jan 1, 1966

By E. R. Cole

One objective of Bureau of Mines recycling research is to devise technology that enables recovery of metals and minerals from wastes. From October 1982 through September 1985, researchers at the Bureau and at the University of Missouri Rolla (contract H0222002) investigated the use of nonferrous flue dust with varying Zn contents (11 to 66 pct) as a source of Zn for electrogalvanizing steel wire. The waste dusts used were from a secondary Cu smelter, a brass smelter, a Pb smelter, and a water treatment plant. The dusts were leached in H2S04, and the leach solutions were treated to make electrolyte for electrogalvanizing steel wire using soluble Zn anodes. Cyclic voltammetry was used in an inno-vative method to evaluate the quality of the electrolytes used for elec-rogalvanizing. After electrogalvanizing, the wire was drawn on a labo-ratory draw bench to simulate industrial practice. Corrosion resistance was measured by a number of electrochemical techniques and by the stan-dard ASTM salt-spray tests. After successful bench-scale tests, the process was demonstrated in an industrial pilot plant. Results indicate that nonferrous flue dusts can be used as a source of Zn for electro-galvanizing if certain impurities are either partially or completely removed from the starting electrolyte.

Jan 1, 1987

By Oliver Bowles

"A Product from Mica Mines.Mica commonly occurs in pegmatites which consist of large crystals of feldspar and quartz, mica constituting but a small proportion of the total rockMuch of the feldspar thus thro n out during the process of mining is pure and of high quality, end the Bureau of Mines has suggested that much of it could be utilized for ceramic purposes. Encouragement is given to such utilization by the fact that several mines now worked for mica were formerly operated for the production of feldspar. ""'here mines are not readily accessible to railroads feldspar utilization might not be feasible, for it is a much lower priced product than mica and cannot therefore bear as heavy transportation expense. '""here mines ire located close to railroads, however, such utilization would tend to reduce the cost of mica mining, and at the same time assist in the solution of the waste disposal problem.The Bureau has recently been informed that some of the feldspar from mica mines near Spruce Pine, N.C., is now being sold and shipped away. An extension of this by-product industry is to be recommended.A Mica Deposit in New York City.The Bureau recently received a mica specimen obtained from a. building excavation at 157th St. and Riverside Drive, New York City. The specimen was about 2 by 4 inches in size, and fairly clear though containing numerous hair cracks. It was obtained only 7 or 8 feet below street level. At greater depth and with more careful methods of excavation material of much better quality might be obtained. The material submitted could be used for mica washers but not for sheet mica. It is stated by an official of a prominent mica company that many such fragments are obtainable in this locality and the possibility of the occurrence of a good mica vein is thereby suggested."

Jun 1, 1920

By J. K. Whyatt

U.S. Bureau of Mines researchers reviewed an in situ stress estimate developed from measurements of overcore strain taken at test sites on the 7300 and 7500 levels of the Star Mine near Mullan, ID. Although the field measurements of over coring strain were found to be useful, significant deficiencies were found in the stress estimation procedure. A new stress estimate was developed incorporating statistical methods and an improved understanding of stress concentration factors for interpreting overcore strains recorded by doorstopper' cells. Spatial variability of overcore strains and the implications for stress field variability were explored.

Jan 1, 2010

By Ricardo Burdisso, Rahul Kadam, Kyle Schwartz, Marty Johnson

Occupational exposure to hand transmitted vibration (HTV) arises from the hand held powered tools extensively used in the mining and construction industry such as rock drills, chipping hammers, chain saws etc. Regular exposure to HTV is the major cause of a range of permanent injuries to human hands and arms which are commonly referred to as hand-arm vibration syndrome (HAVS). In addition to this, the percussive tools generate overall sound power levels in excess of 110dBA in most cases. Such a high sound power level greatly exceeds the maximum permissible exposure limit (PEL) of organizations such as National Institute for Occupational Safety and Health (NIOSH) and the Occupational Safety and Health Administration (OSHA). Long term occupational exposure to this noise has been diagnosed as the main reason for permanent hearing loss in the operators. It is therefore important to develop an understanding of the mechanisms which lead to these high vibration and sound levels and in order to do this a detailed computational model of a pneumatic chipping hammer has been made. This paper presents a nonlinear computational model of a pneumatic chipping hammer. In order to better understand the dynamics of the chipping hammer, the hammer was subdivided into components that are shown in figure 1 (a) (based on a chipping hammer manufactured by Atlas-Copco). The hammer mainly consisted of a center body, a moving piston and a chisel. Compressed air is used to drive the piston inside of a cylinder and on the downward stroke this piston impacts the chisel to create the hammer effect. The machine has one pneumatic valve and this valve regulates the air supply either to the upper chamber or to the lower chamber. The valve changes according to the relative pressures in the two chambers and the supply pressure. There are also twelve different exhaust ports at two positions along the cylinder labeled upper ports and lower ports. As the piston moves the ports can be closed or open (allowing exhaust). Fundamentally, the computational model was made up of two different sub-models, a fluid model and a structural dynamic model as shown in Figure 3 (a) and (b) respectively. The first sub-model takes into consideration the fluid dynamics of the machine since the hammer is driven by compressed air. Equations for the mass flow rate though bleed orifices (assuming an isentropic process) 1 is used to determine the mass flow into and out of the upper and lower chambers. From this the pressures in the two chambers and consequently the forcing on the piston can be calculated. The second sub-model deals with modeling the structural [ ]

Jan 6, 2006

By W. S. Landers

This report presents a detailed study of low temperature, entrained-bed carbonization of an Australian coking coal. The coal studied was high-volatile B bituminous from the Foybrook mine, an open-cut operation in the Liddell seam, New South Wales, Australia. Carbonization was conducted in an 8-inch diameter, continuous vertical reactor at several temperatures from 960° to 1,300° F. It was demonstrated that this bituminous coal can be carbonized within this temperature range to produce tar and a nonagglomerated char, without prior oxidation or char recirculation. Carbonization rates from 138 to 287 lb/hr (as-carbonized basis) were investigated. It was found that the carbonization temperature and the air-to-coal ratio must exceed minimum values to insure continuous operation. At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coa1 ratios, part of the heat for carbonization was supplied externally. On the moisture-and ash-free basis, the yield of tar plus light oil ranged from about 26 to 44 gallons per ton, and the char yield ranged from approximately 1,160 to 1,370 pounds per ton. The heat in the gas ranged from about 900 to 3,000 Btu/lb of moisture-and ash-free coal. Carbonization product yields correlated well with air-to-coal ratio and carbonization temperatures. The volatile matter in the char was found to be temperature dependent. At 1,300° F carbonization, the volatile matter in the char was 8.7 percent (dry basis), whereas at 9600 F carbonization, the residual volatile matter was about 16 to 18 percent (dry basis).

Jan 1, 1965

This publication summarizes the research (in-house and contract projects) programmed by the Bureau of Mines for fiscal year 1984 (October 1, 1983-September 30, 1984) under its Health and Safety Technology Program. The objective of these projects is to provide an ordered and sequenced advance toward the Bureau's overall goal of providing the systems technology required to create a more healthful and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1983

By Harry V. Makar

As part of a continuing research program for conserving domestic mineral resources, the Bureau of Mines is investigating new and improved scrap identification techniques to improve sorted mixed scrap purity. This report focuses on various classes of wrought and cast copper alloys produced with recycled scrap. Based on a survey of the literature, principal alloys, such as the brasses and bronzes, are examined with respect to impurity elements and their effects on metallurgical behavior. Effects of elements such as lead, antimony, iron, chromium, and aluminum are discussed. The metallurgical effects described include hot shortness, fire cracking, and undesirable phase transformations.

Jan 1, 1985

By R. J. Leary

This investigation was conducted to determine the effects of various rare-earth metal addition practices upon the macrostructure and the pattern of sulfur distribution in steel ingots. Heats of plain carbon steel were melted in a 1-ton, basic electric-arc furnace. Melts were treated with mixtures of rare-earth silicides, aluminum, and cryolite either in the furnace before tap or in the ladle after tap to determine the effects of this form of rare-earth treatment upon ingot macrostructure. Steels thus treated with rare earths in the furnace were characteristically free of the gross subsurface nonmetallics which typically result from conventional rare-earth treatments. Steel treated in the ladle showed only a few such nonmetallics, and practical techniques were developed for eliminating most of these. Results showed that furnace deoxidation was controlled by the concentration ratio of rare earths: aluminum. During casting, deoxidation was controlled by the concentration of rare earths. Oxygen contents equivalent to vacuum ladle degassing resulted from air-melt furnace treatments with the rare-earth mixtures described. Rare earths in steel inhibited the onset of equiaxed grain formation during ingot freezing, and also virtually prevented interdendritic segregation of sulfides.

Jan 1, 1968