Search Documents

By Jon C. Volkwein

Dust concentrations inside and outside enclosed cabs on several types of mining machinery were measured by the Bureau of Mines. Results indicated that properly enclosed cabs can offer significant dust protection for machine operators. Recommendations for improvements in cab technologies were discussed.

Jan 1, 1979

By J. W. Hunter, J. H. Jacobs

"Approximately 355 tons of nodules from Chamberlain; S. D., ore were processed in the 1-ton-per-day electrolytic-manganese pilot plant of the Bureau of lanes at Boulder City, Nev., in a continuous 3-month operation. The ore, ground to minus 48-mesh, was found to be amenable to leaching with acid directly or after roasting under reducing conditions in a Skinner muffled multiple-hearth furnace.Unroasted ore gave an acid-leach extraction of 84 to 88 percent of the manganese, which after neutralization showed an over-all extraction of between 81 and 85 percent of the manganese. The amount of iron extracted varied, but it was always,enough to permit the use of ammonia for neutralization.Roasted ore showed an acid-leach extraction of 89 to 91 percent of the manganese. A large amount of iron went-into solution, so that it was not economical to neutralize it entirely with ammonia. By neutralizing with calcine to a pH of 5.0 and completing -neutralization with ammonia to a pH of a.5 an over-all manganese extraction of 84 to 86 percent was obtained. The slight increase in. extraction on roasted ore probably would not justify the cost of roasting.Acid consumption averaged 1.75 pounds per pound of manganese extracted. Settling rates of the residue in leach solution were to slow to permit clarification in thickeners, but a Moore vacuum leaf filter proved to be satisfactory. Purification of raw leach solution was .accomplished readily by hydrogen sulfide with a low gas consumption. Electrolysis was normal, without difficulty, and with -current efficiency ranging between 62 and 66 percent.The use of Chamberlain modules for the production of electrolytic manganese would result in an operating cost of 0.8316 cent per pound higher than the cost of producing electrolytic manganese from Three Wids ore."

Mar 1, 1946

By Paul S. Schopf

The results of an experimental investigation into the possible use of medium energy acoustic fields (130 to 140 dB) to precipitate 1 to 10 micron particles is presented. The aerosol was produced with a LeMer generator using oleic acid and nitrogen. The sound field was a sinusoidal standing wave field in an acrylic tube, with light transmission data used for concentration determination. The results showed collection efficiencies of up to 80% on 2 micron particles with a residence time of 11.8 seconds at a sound pressure level of 139 dB re 2x10-5 N/m2. A discussion of the possible turbulent mechanism is made, as well as review and comparison with others? work.

Jan 1, 1972

By W. H. Eddy

The Bureau of Mines conducted laboratory batch flotation tests and continuous pilot plant flotation tests on a complex calcareous fluorspar ore from Cave-in-Rock, Ill., to determine the technical feasibility of producing commercial-grade concentrates by the sodium fluoride-calcium lignin sulfonate-fatty acid method of concentrating fluorspar previously developed by the Bureau. The continuous flotation tests, treating about 150 pounds of ore per hour, produced fluorspar concentrates assaying 96.4 percent CaF2; 90 percent of the fluorspar was recovered.

Jan 1, 1967

By E. D. Calvert

The objective of this research was to examine variations in melting and forging practice for four titanium-base alloys and to determine their effect on the resultant product. Of particular interest was the evaluation of the skull-casting technique. The data should serve as a guide to producers and consumers of titanium products. Physical properties of four titanium-base alloys in ingot form and in sheet form were evaluated and correlated, where possible, with variations in the melting and casting procedure. Consumable-electrode melting was used throughout, but arc current and furnace backfill pressure were varied, and ingots were formed both by melting directly into a water-cooled copper mold and by skull melting followed by pouring into a graphite mold. Alloying metal additions for the alloys tested were (1) 8 percent manganese, (2) 6 percent aluminum and 4 percent vanadium, (3) 6 percent molybdenum and 2 percent aluminum, and (4) 16 percent vanadium and 2.8 percent aluminum.

Jan 1, 1962

By S. R. Zimmerley, John Gross

"The investigation discussed in this paper was undertaken to obtain fundamental data on crushing and grinding and has been confined, so far, to work on quartz.The results of crushing or grinding have hitherto been judged entirely by the amount of the various-sized particles produced, based. on sieve sizing for particles above 74 microns in size and on microscopic measurement or elutriation for particles below 74 microns - a method which could give only a general idea of what had been accomplished.There was a distinct need of a ""yardstick"" for the measurement of crushed material. It appeared that no advance in the fundamental investigation of crushing and grinding could be made without a reliable method of surface measurement and that such a measurement would have to be based on some property of the surface of the crushed material.A number of attempts based on various surface actions, such as adsorption and heat of wetting, were made to measure surface on quartz particles, but all gave unsatisfactory results. After some preliminary work it was decided that a dissolution method based on Wenzel's law-- ""the reaction velocity between solids and liquids is proportional to the area. of contact""4 -- would be the most feasible.Early use of the dissolution method had been made for surface measurements5, and lately Dr. Geoffrey Martin and his coworkers in England used the dissolution method to determine surface on quartz. They compared the amount of quartz dissolved from a sample in one hour by a hydrofluoric acid solution, with the amountdissolved from a measured quartz cuboid6,After investigating the solvent power of sodium carbonate, sodium hydroxide, and hydrofluoric acid for quartz, hydrofluoric acid was selected as the most suitable solvent, and a dissolution method was developed which gives very reliable results.During the dissolution of quartz in hydrofluoric acid, the reaction velocity changes for two reasons: there is a change in concentration of solution, and a change of surface of the solid. The amount of quartz dissolved in a definite period of time is therefore not a true measure of surface. If, however, the reaction velocity or rate of dissolution for various periods of time be plotted, a curve will be obtained which, if extrapolated to the zero time ordinate, will give the rate of dissolution before any change of surface or any change in the solvent has taken place, and which is a true index of surface. This rate of dissolution, expressed in percentage of the original sample at the zero time ordinate, is designated herein as the ""Initial Rate"" or as simply ""I. R."""

Jul 1, 1928

By David A. Benjamin

At the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied prospects, claims, and mineralized sites in a 43,053-acre portion of the 51,262-acre Desatoya Mountains Wilderness Study Area (NV-030-l10) in 1985. The study area, located 50 miles east of Fallon, NV, is underlain by alluvial deposits of Quaternary age and volcanic and volcanic-derived sedimentary rock of Tertiary age. No mines or recent exploration activity were identified within the area studied. The Gold Basin area, located 1/2 mile to the south has produced 982 ounces of gold and 10,086 ounces of silver. The Cold Springs area, located 1/2 mile to the west, has recently been explored for gold-silver. Mineralization at these two areas apparently did not extend into the study area, but future mining at these areas would likely impact it.

Jan 1, 1986

By John Jordan, Tesarik, Steven J. Knoll, Theodore J. Williams, David K. Denton, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because this condition can result in failures of ground that lead to both injuries and death. Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health studied two methods for identifying stress in rock. A seismic tomographic survey, finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology were integrated to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. Electromagnetic (EM) emissions were also investigated in the Galena Mine, a deep underground mine in Idaho, in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results of this research indicated that (1) seismic tomography appears to be a useful tool for determining relative stress in underground pillars, while (2) EM emissions do not appear to be significant precursors of impending catastrophic ground failure.

Jan 1, 2004

By Martin J. Gavin

[The theory of fractional "eduction" of oil from oil shale has been used by several inventors as the basis for the design of retorts for the production of oil f roan the oil shales of the United States. The term fractional "eduction" gives expression to the rather common belief that when an oil shale is he-test et produces light, low-boiling oils at to temperatures, and increasingly heavier, higher-boiling oils as the temperature of retorting rites. The theory evidently had its is origin in the fact that crude petroleum may be fractionally distilled, yielding light oils at low distillation temperatures, and heavier oils as the distillation temperature increases. Thus, gasoline is produced from petroleum at relatively log: temperatures, kerosene at a higher temperature, and heavier products such as gas-oil and lubricating distillates at still higher temepratures, The writers have examined several oil-shale retorts designed to take advantage of the belief that crude, and en some cases refined, gasoline can be recovered from the shale at low temperatures; kerosene at higher temperatures, and so on. Such retorts are usually designed to operate continuously, and. have several vapor-pipes lending from them at differing intervals and passing to separate condensers. Designers of such retorts expect that the distillate from the low-temperature parts of the retort will be gasoline, and that as the shale basses to zones of increasingly higher temperatures, the vapor lines leading from these zones will remove increasingly heavier products such as kerosene, gas-oil, etc.]

Jan 1, 1924

By Charles Will Wright

This paper has been written to aid the owner of a small gold mine or prospect in preparing a report on his property for the purpose of interesting capital. If an owner can afford to do so, he should employ a mining engineer of recognized standing and experience to examine and report on his property, but many owners of small -mines and particularly of prospects cannot make the expenditure required for this. Further, many of them do not know how to prepare a description which will cover those features of a deposit on which a potential investor promises his opinion as to its worth. If such an owner is convinced that he possesses an orebody of sufficient grade and size to warrant the required expenditure for a thorough investigation and wishes to present his property to prospective investors, then the following suggestions concerning the proper way to sample his deposit, estimate the tonnage of developed and probable ore, and prepare a report may be of assistance.

Jan 1, 1933

By A. W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds from which samples could be obtained in Webster County, W. Va. In 1964, approximately 825,000 tons of coal was produced in the county, of which 732,000 tons was mechanically cleaned in three preparation plants. The Sewell coal bed accounted for 94 percent of the coal produced. Twelve samples were collected from five coalbeds. Four of the samples would require upgrading to meet metallurgical requirements; two others of just over 8.0 percent ash would require some upgrading. In general the coalbed samples collected in the county were of medium-sulfur and medium-to low-ash content as received or after removal of the sink 1.58-specific-gravity material.

Jan 1, 1966

By C. W. Owings

"Coal may be and has been hauled safely at approximately the same cost with permissible2 storage-battery locomotives as with trolley, cable-reel, crab-reel, or nonpermissible storage-battery locomotives. While in general, thinking mining men readily admit the relative safety of the permissible storage-battery locomotive there are some persons who question the safety of this type; however, the greatest opposition to the widespread use of storage-battery locomotives is from those who believe them to be more expensive to operate and to be more expensive in first cost than the trolley or cable-reel locomotive. Data collected during a comprehensive study- of storage-battery and wired transmission of power in some Pennsylvania and West Virginia coal mines indicate that there is but little difference between the cost of hauling with cable-reel or with storage-battery locomotives. It would appear that if this fact were mere generally known mine operators of the more progressive type would install such equipment and avail themselves of greater safety in hauling coal.The need for greater safety in haulage in coal mines is readily understood when it is considered that during the 12 month period, July 1, 1929 to June 30, 1930, trolley or cable reel gathering locomotives caused four explosions in which 407 lives were endangered, 11 persons were injured, and 30 lives were lost. Still another disaster was averted by the vigilance of a fire boss, who discovered a stratum of gas 3 feet thick at the top of an entry into which a gathering locomotive was about to enter. Other explosions not resulting in any fatality probably have not been reported. In addition numerous fires have been caused by trolley or cable-reel locomotives, and these fires probably would have been avoided had permissible storage-battery locomotives been used."

Nov 1, 1930

By J. C. Barrett

Bureau of Mines research on the arc welding characteristics of titanium was initiated in 1948. Little was known about the art except that the easily contaminated metal required more protection from the atmosphere during welding than most other metals. Chambers were designed and built within which titanium could be welded with adequate inert gas protection. Welds were made and their properties studied, and prototype items were made successfully. This report, presenting a resume of the titanium arc-welding experiments undertaken by the Bureau of Mines, demonstrates that the process is successful if conducted under proper conditions and describes the welding of prototypes. INTRODUCTION The Bureau of Mines' first report on methods of joining titanium covered the subject of spot welding,4/ outlining the conditions necessary for producing spot welds in ductile titanium consolidated by powder metallurgy methods and describing the characteristics of such welds. This report embraces the field of fusion weld-ing of titanium and traces the development of suitable methods and equipment for producing such welds.

Jan 1, 1956

A series of laboratory evaluations examined the impact of water spray pressure, curtain setback distance, and external and underboom spray use for controlling respirable dust levels and sulfur hexafluoride tracer gas concentrations around a continuous mining machine. This mining machine was equipped with a flooded-bed dust scrubber and was positioned in the box or slab cut. Exhaust line brattice was used for all tests. Dust levels were measured in the return airway and at locations representing the operators of the continuous mining machine and the standard and off-standard shuttle cars. Increasing water pressure or using the underboom sprays produced no significant impacts on dust levels, although their interactions did produce some significant impacts. Increasing curtain setback distance often elevated dust levels, likely by reducing the amount of airflow reaching the face. Use of the external sprays created additional airflow around the mining machine that pushed the dust cloud past the scrubber inlets. This significantly increased dust levels at all sampling locations. Tracer gas levels were measured on the off-curtain and curtain sides of the cutter head and in the return airway. Increasing water pressure generally led to significantly increased gas levels on the curtain side, although a slight decrease was observed on the off-curtain side with the machine in the box cut. Increasing setback distance elevated gas levels on both sides of the cutter head and in the return by limiting the quantity of ventilation airflow reaching the face. Use of the external sprays provided additional airflow along the off-curtain side of the machine, significantly reducing gas levels in this region. These sprays adversely impacted the dilution and removal of gas on the curtain side of the cutter head. Use of the underboom sprays adversely impacted gas levels on both sides of the cutter head. Use of the external sprays provided the best control of respirable dust and face gas concentrations. The smaller increases in miner operator dust levels produced by these sprays were offset by larger reductions in face gas levels on the off-curtain side of the cutter head. Although the underboom sprays minimally impacted respirable dust levels, use of these sprays was not recommended because they increased face gas levels.

Jan 1, 2007

By R. R. Wells, W. W. Agey

"INTRODUCTION Oxide manganese ore from the Sheep Mountain property was of intermediate grade (23.0 percent manganese) and contained silica as the major impurity. The deposit from which the ore was taken is known as the Sheep Mountain manganese property and is 8 miles west of Durkee, Oreg. Test work was done in the metallurgical laboratories of the Bureau of Mines at Salt Lake City, Utah, on representative samples cut from a 290-pound shipment of crushed ore submitted by the Oregon State Department of Geology and Mineral Industries and reported to be typical of the Sheep Mountain deposit.ACKNOWLEDGMENTSThe authors wish to acknowledge the assistance of R. S. Doan, former assistant director of the Bureau of Mines, under whose supervision the manganese program was initiated in 1940, and, the valuable suggestions made to them by S. R. Zimmerley, now chief, Salt Lake City Division, Metallurgical Branch. Acknowledgment also is made to H. G. Poole and C. H. Schack for their suggestions and contributions to the organization and prosecution of the work of the Ore Dressing Section. Microscopic work on the ores and many ore-dressing products was done by L. G. Evans -and the late. B. E. Head. Our appreciation is extended also to H. E. Peterson, chief chemist, and members of the analytical staff for the many analyses made of the ores and ore-dressing products."

Nov 1, 1947

By R. S. Dean

The principle of explosive crushing depends upon the fact that an expandable substance contained within the pores of a solid body will disrupt such a body upon expansion. Such expansion may be obtained by the detonation of an explosive or by the sudden release of pressure of a superheated liquid. That this principle of disruption may be applied to minerals rests on the fact that cracks, cleavage planes, and pores exist in all minerals to an extent hardly conceived possible heretofore. Crushing by this method takes advantage of forces applied from within the mineral rather than from forces applied from without. The application of a force from within would appear to be more effective.

Jan 1, 1932

By Robert J. Evans

The Hopper-Feeder-Bolter (HFB) is a prototype multifunctional machine designed to improve productivity by minimizing continuous miner place changes. It is designed primarily to work beside a two-pass continuous miner, bolting on one side and then place changing to bolt the other side while simultaneously providing a surge car and lump breaker located directly behind the continuous miner. Surface testing was conducted at the Bureau of Mines Mine Equipment Test Facility (METF) to evaluate overall system performance and reliability. Tests were conducted to evaluate place changing, tramming, lump breaking, roof bolting, drawbar pull, conveying, temporary roof-support (TRS) capacity, lighting, and noise. Surface test results indicate the HFB is ready to be tested and evaluated underground in a production mode.

Jan 1, 1988

By T. J. Ballard

The Union Copper mine is in the Gold Hill district; Rowan and Cabarrus Counties, N. C. The mine was discovered in 1799 and first worked as a gold mine; but copper was encountered at depth, and the property became an important producer of copper. It is estimated that the mine produced 5,000,000 pounds of copper before operations were discontinued in 1907. As part of the strategic minerals program, the Bureau of Mines conducted a development project on the property from July 1943 to November 1943. Eight diamond-drill holes totaling 2,500 linear feet were drilled to delineate the ore body. Analyses 205 core samples were made. Tabulations of sample analyses and drill-hole logs are presented in this report.

Jan 1, 1948

By Vladimir Adamek

This paper describes the Bureau of Mines development of a novel subsidence prediction methodology suitable to the mining and geologic conditions in the Northern Appalachian Coal Region. It describes the computation of vertical and horizontal movements, inclination, curvature, and horizontal strains. The substance of this method is the separation of the effects of lithology by introducing a correlation between hypothetically homogeneous overburden and existing lithologic conditions, while providing for different mining conditions, i.e., underground geometry and overburden thickness. The effects of lithology have been expressed in the form of a variable subsidence coefficient within the subsidence trough. The subsidence coefficient is considered a constant for other predictive methods. Field data from 16 test sites at 11 Bureau longwall panel studies were used in the analysis. For each panel, the characteristics of the variability of the subsidence coefficient were defined. Regression analysis of the subsidence coefficients from all test sites on their locations relative to the edges of their respective panels yielded a third-degree polynomial equation. The results from additional longwall panel studies, not included in the regression analysis, were used to prove the validity of this method. To facilitate the use of this precalculation methodology, a computer program was written in BASIC for use on a personal computer.

Jan 1, 1987

By Michael S. Wieland

Recognizing the dynamic nature and possible range of toxic concentrations in the impending fume cloud prior to undertaking explosive blasting can reduce potential hazards and mitigate related incidents. The scaled cloud model was formulated to predict the relevant (major) toxic components in fume clouds released by nonideal mining explosives used for surface blasting. Natural turbulence unceasingly disperses the toxic molecules, widening (inflating) the fume cloud while diluting the concentrations, ultimately rendering nonhazardous conditions. The threshold cloud size depends upon the type and quantity of total explosives used and the cloud's thermodynamic condition. Though the scaled theory works for fume clouds with irregular (odd) shape, an equivalent upright cylindrical form is useful for rendering simple riskhazard scenarios. The cylinder's projection downward on the underlying terrain yields a circular 'shadow' marking the region threatened, thereby permitting a rough estimation of the potential hazards, were the cloud to settle down there. Wind causes the cloud to drift while it expands, so the shadow travels while it grows, until the risk hazard process is truncated at the nonhazardous threshold. The overall relative fume toxicity (RFT) is taken from the traditional Russian RFT rule, which utilizes only the two fume components that tend to dominate the resultant toxicity: carbon monoxide (CO) and total nitrogen oxides (NOx). Tabulated constants that characterize the fume spectrum in the cloud model were resolved for ammonium nitrate (94%) with fuel oil (6%), ANFO-94/6, using a refined thermodynamic work-principle. Comparable results were found with the reduction factor technique, when test results from the underground fume chamber were readjusted to reflect nominal field shooting conditions.