Search Documents

"These tentative coal mine inspection standards have been prepared as a guide for the Federal inspection of coal mines of the United States. Much time and thought have been spent by various members of the Safety Division in the preparation of thses standards, and it is believed that compliance with them eventually will be possible in most mines. In many instances objections will be raised to them owing to long-established mining customs and practices that are inherently of dubious safety and to a natural inclination to oppose change. In other instances there will be valid objections due to conditions not foreseen at the time these standards were prepared. Or there may be substandard conditions and practices due to original mine layouts that it is not practicable to change during the lifetime of the mine; in such instances it is likely that some effective measures are or can be taken toward lessening hazards.With the rapid change in mining methods some of the standards may become inapplicable and it may be advisable to revise them to meet the new conditions. Therefore, questions regarding these standards and suggestions regarding new standards should be brought to the attention of the supervising engineer of the Coal Mine Inspection Division so that modifications of and additions to these standards may be made from time to time.In many respects these standards exceed the provisions of the various State mining laws, and some may conflict with the laws of some States. In cases of conflict, the intent is not to advocate noncompliance with State laws but to suggest that it may be desirable for the State to reconsider such laws or safety orders.Although an effort has been made to word these standards so that they may be readily understood, nevertheless, a reasonable interpretation should be placed upon them. In fact, in numerous instances the words reasonable"", ""suitable"", and ""properly"" are used in recognition of the fact that reason- and sound judgment enter into the carrying out of the safety endeavor.The policy of the Bureau on some vitally important safety matters in mines is set forth in its published Safety Decisions. These decisions have been consulted and used in the preparation of these standards. These decisions also are now being reexamined by its Mine Safety Board."

Feb 1, 1942

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the fuel-briquet and packaged-fuel producers in the United States and publishes economic data on these industries, based upon reports submitted voluntarily by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all producers of processed minerals fuels. A few small plants may not have been canvassed or failed to respond to the survey because some of the smaller plants operate intermittently and the survey is voluntary. All plants that reported commercial production were included; regardless of size. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, produced by mixing fine-sized mineral fuels with binding materials and compressing into small individual shapes, Briquets are produced in pillow-shaped and cylindrical form, are 2 to 4 inches long, and weigh 2 to 4 ounces. Packaged fuel consists of 3- or 4-inch cubes; 6 or 8 of which are wrapped together in heavy kraft paper to form a package weighing 10 to 15 pounds, Briquets are durable and may be stored and handled as bulk fuel; packaged fuel breaks easily and must be stored indoors to prevent it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times to supplement other fuels. Packaged fuel is burned without re-moving the paper and is referred to as the "white glove" fuel.

Jan 1, 1961

By Oliver Bowles

[Simple systematic accounting that adequately records all transactions has long been regarded as essential to the welfare of any business enterprise. Some of the defects that detract from the prosperity of the slate industry are attributable to a lack of effectiveness in cost keeping. This condition has promoted the United States Bureau of Mines to make a detailed study of accounting methods for the slate industry, and to present for consideration a system of accounts, which it is believe would enable the industry to attain more economical management and operation if accepted by a fair proportion of its important units. The method of accounting presented herein has been worked out with the assistance of leading slate producers and the recommendations are tentative and are submitted in this form as a means of developing constructive criticism. Believing that cooperative effort in this, as in many ether problems will bring the most enduring benefits to the industry as a whole, the writer urges that the cost earnest consideration be given to this vital problem now facing the slate industry.]

Jan 1, 1929

By Kenneth P. V. Lei

The Bureau of Mines investigated a silver-catalyzed oxidative procedure for leaching an arsenical copper sulfide concentrate containing 10 pct As and 32 pct Cu_ Currently, there are no environmentally safe means to treat arsenical copper concentrates in the United States. Leaching was conducted in a 2-L autoclave reactor. The effects of catalyst concentration, O2 pressure, temperature, and H2S04, Cu, As, and Fe concentrations in the leaching solution on extractions of metals from the concentrate were determined. The best leaching conditions for extracting 95 pet eu and As and less than 21 pct Fe were 260 g/L concentrate, 0.007 mol/L (1.0 g/L) AgCI, 3.0 mol/L (294 gIL) H2S04, 1000 C, 60 psig 02, and 6 h. Copper as CuS04-5H20 was recovered by crystallization from the pregnant solution. Arsenic, as AS203, was recovered from the copper mother liquor by solvent extraction, with tributyl phosphate, S02 reduction of As5+ to As3+ in the strip solution, and crystallization of the As3+. The silver catalyst was recovered by contacting the leached residue with a brine solution. A conceptual scheme is proposed for treating arsenical copper sulfide concentrates.

Jan 1, 1987

By David C. Byrne

PURPOSE: Evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. RESEARCH SUMMARY: The results of previous NIOSH research show that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and gender. Using hearing thresholds at 4,000 Hz as an indicator, coal miners experience hearing loss 2.5 to 3 times greater than would be expected for persons not exposed to occupational noise. At age 50, 90% of coal miners and 49% of metal/nonmetal miners were found to have a hearing impairment. In comparison, only 9% of a nonoccupationally exposed control group had a hearing impairment at age 50. There are numerous barriers to the prevention of hearing loss among miners. In an effort to overcome some of these obstacles, this work was initiated to evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. Experiments will involve analysis of this new technology under both laboratory and field conditions. Laboratory components will consist of controlled studies using an anthropometrically correct test fixture as well as human subjects to evaluate the adequacy/effectiveness of various hearing protective devices. Electroacoustical performance testing of new noise monitors will also be conducted in a laboratory setting. Subsequent field studies will determine the actual usefulness and practicality of the personal protective/monitoring equipment as used in different mining situations. It is anticipated that increased on-the-spot awareness of hazardous noise levels and the availability of better-suited hearing protectors will provide a degree of protection beyond what is currently attained in different mining environments. Therefore, the intent of this project is to identify and adapt new acoustical technologies and products that have a direct application to individual mine workers. With increased knowledge of these technological advances, a greater demand for similar devices will likely occur, which, in turn, will lead to a better understanding and awareness of hearing loss prevention methods throughout the mining community. The ultimate goal is for widespread integration of useful hearing loss prevention products and devices into the daily routines of miners

Jan 2, 2000

By W. E. Wallace

Volume-rate-of-flow measurements were made of the flow of mercury through porous samples under conditions of no field, magnetic field transverse to the direction of flow, and transverse magnetic field and electric current to determine if a magnetic method might be potentially useful in the study of pore-size distribution. No change was observed in the flow rate from the application of a magnetic field alone. The application of both field and current produced an electromagnetic pumping action with or against the direction of flow, depending upon the direction of the electric current. This pumping effect was observed to be greater in a rectangular porcelain sample than the calculated value for an equal-Sized open channel.

Jan 1, 1969

By F. W. Wessel

Manganiferous carbonate slates of the Cuyuna range, which are part of the unoxidized thin-budded iron formation, represent a large potential source of manganese. This report details recent bench-scale research by the Federal Bureau of Mines in applying mineral-dressing techniques to these materials in order to investigate their potential uses. Work outlined in the report was directed toward the production of concentrates usable as iron-blast furnace feed, but an equally important objective might have been to furnish an enriched feed for extractive processes for recovering manganese. Flotation concentrates were prepared that contained 11.1 percent manganese, 27.8 percent iron, and 12.2 percent silica, with recoveries of 73 percent of the manganese and 48 percent of the iron. Calculated analysis for a simulated sinter suggests a product containing 16.0 percent manganese, 40.2 percent iron, and 17.6 percent silica, with 31 percent recovery of the dry weight of the ore. The silica in the flotation concentrates was due to quartz and iron silicates. Substantial quantities of the iron silicates (stilpnomelane and smaller amounts of minnesotaite) were present in the slate, and the need to reject these minerals limited the recovery of iron. The sintered flotation concentrate would be usable as ferruginous manganese ore for iron blast-furnace feed because of its favorable manganese silica ratio. The unsintered flotation concentrates, representing 45 percent of the feed weight and containing manganese enriched in the ratio of 1.6 : 1, also could be used as feed to processes for extracting manganese.

Jan 1, 1961

After more than 20 years dependence on bituminous coal as a primary fuel for generating electricity, the Pennsylvania Power and Light Company initiated a one-year study on the economics of building an electric generating station using anthracite as a fuel. The study will be completed in December 1976. If the feasibility study so indicates, PP&L will consider installing four 400,000 kilowatt generating units for scheduled commercial operation in 1985. Each unit would consume up to one million tons of anthracite annually. Anthracite generally is more difficult and expensive to extract than bituminous coal, but it has a significantly lower sulfur content than the bituminous coal currently being used by PP&L, thereby eliminating the costs of installing sulfur emission controls at generating stations. Moreover, significant reductions in transportation costs may be realized because the utility's operating territory is situated in the center of the anthracite region in northeastern Pennsylvania. These advantages may indicate that the use of anthracite is more economical than bituminous coal to PP&L. ASBESTOS -Asbestos production in the U.S. dropped again in 1975 until it was just two-thirds of that in 1973. This was in spite of the very strong demand caused by the Quebec strike. The 7-month strike of the asbestos miners in Thetford Mines, Quebec cut off 55 percent of the normal supply of U.S. consumers. Apparent domestic consumption was less than 75 percent of that in 1974. The wage settlement will probably result in a 20 percent increase in asbestos prices.

Jan 1, 1975

By W. L. Staker

The Bureau of Mines investigated the use of shredded automobile scrap for copper cementation. Air agitation was used to improve the cementation rate and prevent excessive buildup of copper on the iron. The pieces of scrap were too large to be properly evaluated in the laboratory; therefore, a pilot scale test unit was constructed and the process tested at field locations. Pregnant solution was obtained from industrial leaching operations, processed in the test unit and the barren solution and cement copper were returned to the plant process stream. The test results showed that the air-agitated launder containing auto-mobile scrap was an effective means for recovering copper from leach solutions. A continuous l4-day test run was made without a noticeable decrease in cementation efficiency. The most suitable scrap product was obtained from incinerated automobile hulks shredded in a hammer type of shredder. However, it was necessary to remove small pieces such as nuts and bolts because they interfered with the discharge of the copper product.

Jan 1, 1976

By J. C. Franklin

A data-acquisition system was designed by the Bureau of Mines to monitor five detectors with radon continuously flowing through each. These detectors could be monitored up to 12 times an hour, but were only monitored according to a preset time, thus allowing radon to be monitored continuously in a uranium mine. The counter can be set to monitor each detector for any period of time up to 16.5 minutes. This allows very low concentrations to be monitored longer to reduce statistical error. There would be no upper limit in radon concentration that could be monitored, but there would be a lower limit of 50 picocuries per liter (pCi/l). Each detector was cylibrated in the laboratory by the Lucas flask method. Multiple samples were taken at two different concentrations, and the correction factor for each detector was determined by a least squares fit of the data. To verify the calibrations, a series of measurements at several concentrations were made against a constant source. Our agreement at low radon concentrations (300 pCi/i) with the two-filter method as within 3 percent; thus, the total error would be this difference plus the two-filter error. At high concentrations the coefficient of variation ranged between 2.1 and 9.8 percent for the five different detector units.

Jan 1, 1976

By Maurice J. Peterson

THE VISUAL-ARC spectroscopic method of rapid qualitative analysis of complex inorganic compounds has been popularized in the past few years and is being employed by an increasing number of laboratories. The mineralogy and chemistry departments of several universities recently have added visual spectroscopy to their laboratory curricula. This revival of interest in a somewhat dormant analytical method has been stimulated through the publication of three papers 4 by members of the College Park staff of the Bureau of Mines. These virtually are the only recent sources of information on visual-arc spectroscopic analysis. They include data on the spectroscopic assembly, the analytical procedure, and the practical application of the method to determinative mineralogy and related fields. Requests for reprints of these papers continue to be received; at present only a limited number of copies are available for distribution. In order that these requests may be adequately answered, material from the three papers has been combined and, with some additional data, is presented in this bulletin. Numerous specific inquiries have been received regarding types of equipment available, problems in instrumentation, and information on the approximate sensitivity limits of the elements that can be detected by this method. Some of this material was not included in the original papers. Accordingly, the table of wavelengths has been revised to include the approximate visual-arc spectroscopic sensitivities, and a section on commercially available equipment has been added.

Jan 1, 1953

By Robert L. Morris

A new concept of roof support by "sonic pin-setting" is introduced. Initial experiments indicate that this method could introduce tremendous benefits for the coal mining industry by making roof-bolting a faster, safer, and more economical operation. A theoretical model is presented for describing the process and an experimental machine was built. The present testing results are included.

Jan 1, 1977

By Mark S. Stagg

Blast-induced ground vibrations from surface coal mine, quarry, and construction blasting were measured and analyzed for frequency content and duration characteristics. Eighteen commercially available ground vibration measurement systems were evaluated in the field and laboratory for linearity, accuracy, and crosstalk. Buried, surface, and sandbagged transducer placement methods were compared, along with peak and vector-sum measurements. The recommended minimum frequency ranges for ground vibration instrumentation are 2 to 150 Hz for coal mine and quarry blasting, and 5 to 200 Hz for construction and excavation blasting. When higher or lower frequency vibrations are possible, as in construction blasting or for a quarry shot close to a residence, care should be taken to insure proper choices of instrumentation and vibration criteria. Several instruments operating in these ranges are available, and all but one of the seismographs tested fell within ±3-dB accuracy limits (+41 pct, -29 pct). Waveform recordings of all three ground vibration components are recommended as the peak amplitude and frequency may vary among the three. Peak or vector-sum readings are adequate if only amplitude levels are desired. The soil density matched box should be anchored or buried, particularly for high-frequency, high-amplitude construction blasting.

Jan 1, 1980

By M. F. Dunn

During a mine fire or other emergency, it may be desirable to reverse the airflow in order to provide an escapeway or to isolate a fire. Also, in colder areas, the airflow may be reversed to prevent ice buildup. When reversing main mine fans, the mine operator usually does not know what operating characteristics of flow and pressure to expect. Laboratory and field tests of vane axial main mine fans in the 7- to 9-ft diameter size range were conducted to establish forward and reverse performance characteristics under controlled conditions and at typical mine installations. The data obtained suggest that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. There is also evidence that reverse performance can be predicted for a family of blade angles and a given hub to tip ratio. Generally, quantity of air is 30 to 65% less in reverse than when operating in the normal forward mode.

Jan 1, 1983

By d&apos, Kathleen J. Amico

THIS SUMMARY appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U .S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed ?mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1965

By C. H. Schwartz

A thermal radiation probe was constructed and tested in pulverized-coal-fired furnaces. A rotatable sensing head on the side of a water-cooled probe permitted measurement of radiant flux within a 7.20 cone from any desired direction to a point within a furnace. A response curve for a corner-fired furnace showed radiant flux of 130,000 Btu per sq ft per hr, when viewing flame, and 60,000 Btu per sq ft per hr, when sensing wall reflection. Detailed drawings and fabrication procedure are given.

Jan 1, 1970

By D. Harrington

For many years the Federal Bureau of Mines-in cooperation with other agencies-has been making investigations and compiling and publishing reports and statistics on accidents in the various branches of the mineral industry.4 Its assistance has been enlisted also in health, safety, and ventilation problems' incident to the driving of many large tunnels in the United States in recent years. As part of this work the Bureau has compiled considerable statistical and other information on accident experience in the tunneling branch of the heavy-construction industry. It has always been difficult to obtain up-to-date information on tunneling methods and tunnel accidents. Published accounts of tun¬nel construction furnish much interesting material of engineering, historical, or fiscal value, but usually little or no attempt is made to discuss and critically analyze the means taken to preserve the health and life of employees.

Jan 1, 1941

By Walter D. Holland

This document is one of a series of instruction guides developed to help instructors present health and safety training courses to workers in the metal and nonmetal mining industry. This course is intended to provide above ground metal and nonmetal mining employees with training which will assist them in performing their work safely and healthfully. A document entitled, "Airborne Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas," is used as a manual for the students during the course. The unique features of the teaching guide are thumb rules for recognizing hazardous situations, candidate contamin¬ants for each work area and descriptions of control devices and work procedures.

Jan 1, 1977

By F. E. Armstrong

Tritiated water has been used as a tracer to follow the path of leach liquids as they flow through a copper-mine dump. Semipermeable layers, produced within the dump by compaction and "stratification" of deposized dump material, restrict the vertical movement of water. Knowledge of this restriction would aid in the optimization of the leaching process. The portion of the dump of particular interest was approximately 2,000 feet long, 800 feet wide, and 200 feet high. A total of 94 curies of tritiated water was injected into the dump at the rate of 650 gpm over a period of 39 hours. The leach liquid was sampled at natural surface outflows and through a series of wells, some drilled to the bottom of the dump and others to intermediate levels. More than 3,300 samples were analyzed, most by liquid scintillation counting, but a few hundred by gas counting. Data obtained permitted calculation of flow paths, recycle times, total fluid volume, and estimates of retention times in various portions of the dump.

Jan 1, 1971

By Charles B. Kenahan

A summary of Bureau of Mines research on utilization and disposal of solid wastes is presented, accompanied by an extensive bibliography of related publications. The Bureau's Solid Waste and Materials Recycling Program is directed toward four main areas of research, development, and demonstration: (1) extraction of mineral, metal, and energy values from urban refuse; (2) upgrading and recycling of automotive and related ferrous and nonferrous scrap; (3) utilization and stabilization of mine, mill, and smelter wastes; and (4) recovery and reuse of values from industrial waste products. A contract and grant program that supplements the in-house research and aids in the training of manpower in management of mineral-, metal-, and energy -based solid wastes is also discussed. This publication is an updating of Bureau of Mines Information Circular 8460 issued March 1970.

Jan 1, 1971