Search Documents

By Andrew B. Cecala

This U.S. Bureau of Mines report provides a detailed description of the Bureau-designed modified shearer clearer system. Engineering drawings are provided for all major components of this system. The modified shearer clearer system is a revised version of the original system and is intended to improve the ventilation around both cutting drums. The original shearer clearer technique was solely a dust control technique that has been effective in lowering shearer operators' dust exposures. The technique uses a series of water sprays that not only knock down a portion of the dust cloud but also act as small fans that move a substantial amount of air and keep the dust cloud from dispersing over the shearer body. The modified version is composed of two additional spray blocks for improved air movement around both cutting drums, thus lowering methane levels and the likelihood of an ignition. A laboratory study performed with the modified version in a full-scale longwall gallery resulted in a 73-pet reduction in methane concentrations at the shearer machine for both cut directions. The air-moving capabilities of the system provide more turbulence at the cutting drums and reduce methane levels.

Jan 1, 1994

By James P. Ulery

Explosions in U.S. coal mines have caused death and injury to miners and destruction of workings since the first reported explosion in 1810. These explosions are caused when buildups of explosive gas and/or dust in the mine are ignited by the presence of a flame or spark. Methane gas is inherently generated and held by adsorption in coal and is normally liberated during mining. Because this gas is explosive in the range of 5%–15% by volume, fresh air is constantly supplied to the working face to prevent the methane/air mixture from reaching this explosive range. The required amount of ventilation air is based on estimates of gas release under normal conditions. Occasionally, unanticipated and unusually high emissions are encountered, which, despite normal ventilation controls, result in an explosive mixture that a spark from a cutting bit or electrical equipment can easily ignite. Investigations have shown that such emissions are often associated with anomalous geologic features or conditions. Although most operators are aware that certain geologic features may adversely affect productivity, few are aware of their potential as a gas emission hazard. This report presents a historical framework detailing the impact of geologic features on excess gas emissions and resultant mine explosions. It also provides operators with specific information on recognizing and alleviating potential hazards from methane emissions related to these geologic features.2

Jan 4, 2008

By H. D. Hess

This report describes in detail a unique occurrence of fersmite, (Ca, Ce, Na) (Cb, Ti, Fe, Al)2 (0, OH, F)6, which occurs as small anhedral inclusions and intergrowths with a tantalum-free columbite found in the metamorphic complexes of Ravalli County, Mont. Chemical and crystallographic data along with the physical and optical properties agree in general with those given in the original description of fersmite from the Ural Mountains of Russia. X-ray diffraction data not given in the original description and more specific optical data have been determined. The Montana fersmite, now established as the second occurrence of this rare calcium-columbate mineral, was discovered during a routine Bureau of Mines mineralogical examination of a prospector's sample.

Jan 1, 1960

By F. W. Hoertel

The effects of certain process variables on the grain size, grain type, and microhardness of vapor-deposited tungsten were established, and the near-optimum parameters and the efficacy for the vapor deposition process were determined. No significant change in the grain size or microstructure resulted from ultrasonic vibration of the substrate during deposition, from variations in the hydrogen (H2) to tungsten hexafluoride (WF6) ratio, or from small increases in reaction-chamber pressure. Near-optimum conditions were continuous deposition at atmospheric pressure, a deposition rate of 2-mils thickness/square inch of substrate area/hour, a temperature of 5500 C, and a hydrogen to WF6 ratio of 4:1. The addition, individually, of about 2 volume-percent of butane, 24 volume-percent of carbon dioxide, or 4 volume-percent of propane to the hydrogen and WF6 mixture produced deposits with the finest grain size for each gas. A corresponding increase in microhardness accompanied the decrease in grain size. The addition of gases did not alter the columnar microstructure found in vapor-deposited tungsten.

Jan 1, 1966

By Rodney D. Rosenkranz

The Bureau of Mines evaluated the potential supply of primary copper from domestic mines and deposits and found that increases in copper price will be required in order for many domestic deposits to continue production. As part of the study, a tonnage-price relationship was developed indicating the quantity of copper that could be produced economically from known deposits at various copper prices and at various rates of return on the required capital investment. Costs of production are based on estimated capital and operating costs for mining, concentrating, transporting, smelting, and refining. Direct and indirect operating costs, recovery of investment, and return on investment have been included in the smelting and refining costs. Capital and operating costs are calculated in January 1978 dollars, and byproduct credits are based on January 1978 prices. Known domestic copper mines and deposits contain nearly 92 million metric tons of copper in about 14 billion metric tons of demonstrated mineralized material. These tonnages represent the current domestic copper reserve base. Approximately 74 million metric tons of copper are recoverable from the reserve base using existing technology. Of this quantity, slightly more than 50 million metric tons are economically recoverable assuming a price of 51.00 per pound of copper, credit for the recovery of byproducts, and a 15-percent rate of return on capital investment. Approximately 60 percent of the copper occurs in mines that were producing at the time of the study.

Jan 1, 1979

By Charles E. Whieldon

Data on the oil fields in Mahoning Columbiana, Carroll, Jefferson, and Harrison Counties, Ohio, were collected from scattered sources and com- piled to make the information readily available to operators who may be interested in conducting secondary-recovery operations in the area. General geology, oil production, oil-productive acreage, core data, reservoir calculations by townships, and miscellaneous data and reference material are presented.

Jan 1, 1965

By d&apos, Kathleen J. Amico

This summary appears in Minerals Yearbook volumes I-II, and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonweath of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The sections of this chapter and the area chapters in volume III contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1967

By M. G. Cherniack, A. J. Brammer, D. R. Peterson

Over the past two decades, there have been significant reductions in industrial exposures to hand-arm vibration, especially when specific tools and work processes have been redesigned to incorporate anti-vibration and ergonomic principles. Nevertheless, Hand-Arm Vibration Syndrome (HAVS) remains a significant occupational health problem as disease symptoms continue to occur even when vibration exposure levels believed to incur low risks have been reached2. This inconsistency may be related to the methodology that is typically used to estimate workday vibration exposure levels, involving laboratory and/or very short duration field measurements coupled with estimates of overall eight-hour tool operation times determined from brief observations of tool tasks and/or self-reported surveys. One solution is to use small, commercially-available, personal vibration dosimeters to calculate, record, and display long-duration vector sums and energy equivalents of vibration. However, since these devices are attached to the worker and require tool-mounted accelerometers, they are incompatible with the worker performing normal duties involving putting down or changing tools. In addition, these commercial systems do not allow for the characterization of the transmission of vibration to the hand such as monitoring the mechanical coupling between the hand and the tool handle (e.g., grip forces). O’Boyle and Griffin showed that variations in applied force can alter vibration transmission characteristics by 50% or more indicating that the measurement of grip force is essential for modeling vibration transmissibility and vibration exposures5. In summary, a need exists for the development of a method and device that will more accurately characterize workday-long vibration exposures. Methods A portable, light-weight, Vibration Exposure Monitor (VEM) system was developed to record user-specific tool-operating times, vibrations, and grip forces throughout all, or a representative part, of a workday. It monitors frequency weighted and unweighted accelerations from a palm-mounted uni-axial accelerometer (Model 352C22, PCB Piezotronics, Depew, NY) and calculates exposure levels using the root-mean-square (RMS) and higher power mean values, such as the root-mean-quad (RMQ) and the root-mean-oct (RMO). Grip forces are also monitored using a palm-mounted force sensor (Model 400, Interlink Electronics, Camarillo, CA) from which average grip force levels and exerted grip extrema are calculated. At the core of the VEM system is a commercially available, battery-powered microcomputer (Tattletale, Model 8v2, Onset Computer, Onset, MA) with one megabyte of memory and eight analog channels using 12-bit sampling at a single-channel maximum of 100 kHz. Analog signal processing (i.e., anti-aliasing, with cutoffs at 4 and 1250 Hz, and ISO 5349-13 frequency weighting) is accomplished using custom circuitry that is directly interfaced with the microcomputer. An embedded C-based protocol governs the data collection from each channel

Jan 6, 2006

By A. J. Kraemer

This report on the physical and chemical properties of crude oils of California is one of a series on the producing districts of the United States. It includes a short discussion of results, tabulated data, and individual analyses of California crudes. Analyses of crude oils from the fields of Fresno, Kern, Los Angeles, Orange, and Ventura Counties have been published in Serials 25952 and 26083. The analyses reported in this paper corer samples that were obtained subsequent to the publication of Serials 2535 and 2608. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting of samples was facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1927

By Webster S. Anderson

Bureau of Mines planer mining tests on the phosphate bed of the Douglas mine, near Drummond, Mont., indicated that a competent bed with a Mohs' scale hardness of 3 to 4 cannot be mined economically with the planer. Although planer mining was feasible where the bed was fractured enough for a 4-inch depth of cut to be consistently maintained, the depth of cut in the competent beds at the Douglas mine did not exceed 0.5 inch. Average production rates were 0.15 ton per minute and 9 tons per man-shift.

Jan 1, 1966

By J. F. Barkley

Field tests were made on the rate of corrosion of 30 materials used in air preheaters under regular operating conditions, and the buildup of deposits was observed. Twenty-three materials were tested with coal as the fuel on an underfeed stoker and seven with oil, including a short period with pulverized coal as fuel, The plant equipment is described, and pertinent plant operating data are tabulated. Figures 17 and 19 (pp. 24 and 27) give the results of corrosion tests on the uncoated metal test specimens. The information obtained from these tests follows the general pattern described in Bureau of Mines Report of Investigations 4996, Corrosion and Deposits in Regenerative Air Preheaters. The deposits were similar, and the corrosion rates of Cor-Ten and Mayari-R steel (previously found to be essentially the same at the Harding Street Station using coal) continued to show little difference at the Marion Generating Station using principally oil. The one high-alloy steel tested, type 321, showed a much higher corrosion rate than the low-alloy steel, Cor-Ten.

Jan 1, 1959

By Jr. Hardy, H. Warren Shen

"A study is presently underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which would make it possible to carry out remote monitoring of coal cutting operations. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal breakage and cutting procedures. The present paper will focus on the test facilities, experimental techniques, and results associated with linear, single-bit cutting. An AE-transducer, attached directly to the bit, detected AE signals during the cutting process.Experiments have been carried out on seven specimens of coal obtained from the USBM experimental mine at Bruceton, Pennsylvania. Three separate cuts were made for each of two bit angles (10 and 45 degrees) and two bit velocities (0.085 and 0.169 cm/sec), for a total of 12 separate cuts. Data associated with resulting particle size distribution and AE characteristics (major dominant frequency components) will be discussed. Data analysis has also been underway using a computer-based pattern recognition system known as ICEPAK (Intelligent Classifier Engineering Package). This program is able to evaluate over 100 features of an AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. The results to date show that AE generated during some of the test conditions can be recognized by ICEPAK with a recognition rate of 90% and higher while other conditions cannot at present be separated with a suitable recognition rate. Further analysis of the experimental data is presently underway.The reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust, and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which would make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit conditions and cutting efficiency, and to quantify the particle size and shape distribution of the generateddust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. To date experiments have been carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. A brief outline of the overall study has been presented in an earlier paper (Hardy, Shen and Kimble, 1995). This paper will consider the linear single-bit cutting studies in more detail.It is generally accepted today that most solids emit low-level seismic signals when they are stressed or deformed. In this paper this phenomenon will be referred to as acoustic emission (Hardy 1972, 1981, 1989). In essence, the measurement of AE activity in a field or laboratory structure is relatively simple. A suitable transducer is attached to the structure, the output of the transducer is connected to an associated monitoring system, and the AE signals occurring in the structure, due to internal or external stress, deformation, and failure are suitably acquired, pre¬processed and recorded."

Jan 1, 1998

By Clayton M. Rumsey

No producing or developing mines nor known mineral resources are in the Lower Saline Valley Wilderness Study Area. The inactive Bonanza Prospect has low potential for copper-gold-silver resources. Stone and sand and gravel deposits in the WSA do not constitute mineral resources because transportation costs to major markets are prohibitive. INTRODUCTION The Lower Saline Valley Wilderness Study Area (WSA) covers 2,241 acres in southeast California adjacent to and west of Death Valley National Monument (fig. 1). Access to the WSA is by the Saline Valley gravel road 28 mi northerly from its junction with State Highway 190. The junction is about 35 mi southeast of Lone Pine, CA. The WSA is characterized by moderate to steep, sparsely-vegetated slopes; elevation ranges from about 1,800 ft to 3,560 ft.

Jan 1, 1984

By N. S. Dalal, X. Shi

"Electron spin resonance measurements provide evidence for the formation of long-lived Cr(V) intermediates in the reduction of Cr(Vl) by glutathione redtuctase in the presence of NADPH and for the hydroxyl radical formation during the glutathione reductase catalyzed reduction of Cr(Vl). Hydrogen peroxide suppresses Cr(V) and enhances the formation of hydroxyl radicals. Thus Cr(V) intermediates catalyze generation of hydroxyl radicals from hydrogen peroxide through a Fenton-like reaction. Thus the mechanism of Cr(VI) toxicity might involve the interaction between macromolecules and the hydroxyl radicals.C(Vl) compounds have been found to exert serious toxic and carcinogenic effects on humans and animals (1-3). In contrast, most Cr(III) compounds are relatively nontoxic, noncarcinogenic, and nonmutagenic (1,4). Cr(VI) and Cr(III) oxidation states are different in their metabolic pathways: Cr(VI) , ions are rapidly transported across cellular membrane (1,4,5), while Cr[III) moieties do not easily penetrate cells and are not oxidized by cellular constituents (!). Since it is known that the reduction of Cr(VI) ion is required for its reaction with DNA (1), the molecular mechanisms for the intracellular Cr(Vl) reduction has been the focus of current studies but the details are still not understood.Earlier studies on the mechanism of Cr(Vl) reduction include those on the reduction of Cr(VIJ by glutathione (GSH) .0,6-8), ascorbic acid (9), glucose (10), lactose (IO), galacturonic acid (11), microsome (12), and mitochondrial electron transport chain complexes (13). These studies have shown that the Cr(VI) reduction involves the formation of Cr(V)-containing species which are often considered to be the toxic form of chromium. Thus far, however, no information is· available on the subsequent fate of those biologically formed Cr(V) species, in particular employing well defined biochemical systems. In this context, we report here our investigations of the reduction of Cr(VI) by glutathione reductase (GSSG-R). This enzyme was selected because it is ubiquitously present in cellular systems and it has been postulated to be involved in the Cr(VI) reduction (14-17) but the underlying mechanism has not been clarified. We find that the reduction proces·s involves not only Cr(V) but also ·OH radicals. We further investigate the reactivity of Cr(V) and find that it catalyzes generation of OH radical from H2O 2 through a Fenton-like reaction. The role of ·OH in Cr(VI) carcinogenicity is suggested from this study."

Jan 1, 1989

By Larry A. Lass

The U.S. Bureau of Mines, in cooperation with the Iron Range Resources and Rehabilitation Board, investigated the potential of using northeastern Minnesota papermill waste sludges as a binder for Mesabi Range iron ore (taconite) concentrate. Sludges from five different commercial papermill waste treatment operations were evaluated in laboratory tests. Except for the coarsest sludge, all were fairly easy to blend with the taconite concentrate using conventional mixing methods. The coarsest sludge had to be reslurried at 2 pct solids before adding it to the concentrate in order to obtain pellets without visible sludge clumps. Drying and grinding the sludges made them less effective as binders because of a lower degree of rehydration. On a dry weight equivalent basis, twice as much raw sludge binder was required to obtain similar pellet physical properties as with bentonite; however, the pellets made with raw sludge had superior metallurgical properties. Over 30 pct higher reduction rates and over 1500 C higher softening temperatures were obtained with sludge binder than with bentonite. Sludge D, which had the lowest fiber and the highest alkali metal content, resulted in the lowest reducibility enhancement. Even though more raw sludge was required than bentonite, the sludges have virtually no value, and therefore may provide a cost-effective additive binder for producing improved metallurgical-quality pellets. Large-scale testing has not been done to confirm these laboratory results.

Jan 1, 1989

By C. Q. Cupps

Rate of gas diffusion in reservoir oil has been investigated in an effort to explain the variation in oil characteristics observed in the Weber Sandstone reservoir, Rangely field, Colorado. Coefficients of gas diffusion were determined experimentally for the Rangely oil system and used in a mathematical simulation of gas diffusion during the probable life of the Rangely reservoir, estimated at 65 million years. The simulator involved solution of Fick's law for diffusion in two dimensions by the method of finite difference and successive over-relaxation. The results show that continuing gas diffusion is a logical explanation for the variation in oil characteristics at Rangely and that the pattern of gas distribution by diffusion in an asymmetrical reservoir will not conform to structural contours as originally proposed.

Jan 1, 1971

By David F. Smith, F. A. Hartgen

"Incidental to a cooperative investigation with the Carnegie Institute of Technology and the International Combustion Engineering Corporation on the burning characteristics of a powdered coal and the powdered semi-coke therefrom, the U. S. Bureau of :alas has determined the relative temperatures at which rapid self-heating occurs in these two fuels. Determinations were made on various screen sizes of the two fuels. Chemical analyses on different sizes were made in the bureau's Coal Analysis Laboratory, of which H. M. Cooper is in charge. The true densities were determined b the method given in Bureau of Mines Technical Paper 8.4The apparatus used in the determination of the temperatures for rapid self-heating was similar to that used by Wheeler A 10-gram sample of the fuel was placed upon a screen in a glass tube enclosed in a vertical electric furnace. The tube was surrounded with sand. One thermocouple -as imbedded in the sand and another in the fuel. Measurements of the temperatures were obtained at regular intervals with a recording potentiometer, as the furnace temperature was uniformly raised. Dry air was passed down through the fuel samples at a uniform rate of 123 c. c. per minute; the temperature of the air was substantially that of the furnace."

Oct 1, 1929

By Jeffrey Shawn Peterson

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. In response, the National Institute for Occupational Safety and Health (NIOSH) conducts research to reduce the noise emission of various underground coal mining equipment, an example of which is a roof bolting machine (RBM). After the removal of coal or rock, the remaining strata may be subject to fall, either from overhead (the roof) or from the side (the rib). One method used in underground coal-mines to prevent failures requires the installation of roof bolts. The roof bolting machine operator trams the machine to the required location, drills a hole into the strata, and then installs a roof bolt, supporting the roof or the rib, as the case may be. Field studies support the premise that, on average, drilling noise is the loudest noise that a roof bolting machine operator would be exposed to and contributes significantly to the operators? noise exposure. NIOSH has determined that the drill steel radiates a significant amount of noise during drilling. NIOSH is developing bit and chuck isolators to reduce vibration, and thus noise radiation of the drill steel, with the longer-term goal of reducing roof bolting machine operator noise exposure. Laboratory testing has shown that operator ear sound pressure levels may be reduced by 3 to 7 dB(A), depending upon the test configuration and drilling media.

Jan 1, 2009

This is the fourth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-363/. The second report gave the same data? for motor gasolines sold during the summer of 19364/. The third report of the series gave the same data for motor gasolines sold during the winter of 1936-375/. This report covers 63 brands of gasoline represented by 1,136 samples excluding the Pacific Coast. Those from the Pacific Coast were averaged by the Pacific Coast technical group before being submitted and are published exactly as they were submitted. In some areas reports were received from five or six companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative than others.

Jan 1, 1937

By M. M. Fine

This Bureau of Mines report describes the theory, experimental procedures, and the results obtained to date in the development of the Bureau's process for magnetically roasting iron ores using scrap iron as a means of reduction. Since magnetic separation is an operational step common to magnetic taconite plants, the preliminary research studies emphasized only the novel magnetic roasting step. The studies included the use of automobile scrap, ferrous reductants such as borings and turnings, and prereduced pellets. Technical feasibility of the process was demonstrated both on a bench- and pilot-scale. Quality magnetic concentrates with recoveries of over 90 percent were obtained from a direct shipping ore containing 59.5 percent Fe and from fine grained semitaconites with about 30 percent Fe.

Jan 1, 1966