Search Documents

By L. H. Adami

The heats of formation of anhydrous cadmium sulfate, cobalt sulfate, copper sulfate, nickel sulfate, and zinc sulfate were determined by hydrochloric acid solution calorimetry. The values at 298.15° K for formation from the metal, rhombic sulfur, and oxygen gas follow (cal/mole): CdS04J -222.0 ± 0.3; CoS04, -212.0 ± 0.4; CuS04) -183.4 ± 0.6; NiS04, -208.1 ± 0.2; and ZnS04, -233.1 ± 0.2. Corresponding heats of decomposition to form the metal oxide, sulfur dioxide, and oxygen were derived from these results; heats of decomposition to form the metal oxide and sulfur trioxide were also derived.

Jan 1, 1965

By O. C. Blade

This report is one of a series made by the Bureau of Mines under a cooperative agreement with the American Petroleum Institute on the characteristics of commercial aviation gasolines. The series of Surveys is a continuation of like work conducted under aimil.ar cooperative agreements with the Coordinating Research Council, Inc. by the National. Bureau of Standards from 1940 through 1946 and by the Bureau of Mines from 1947 through 1949. A completed list of the series of surveys is given at the end of this paper.

Jan 1, 1951

By R. L. Montgomery

The heats of formation of lanthanum sulfate and the enneahydrate are -939.8 ± 3.1 and -1,587.1 ± 3.2 kcal. per mole, respectively. The heat of hydration is -32.5 ± 3.5 kca1. per mole. These values were obtained from heat-of-solution measurements of lanthanum oxide and salts. Low rates of solution precluded more accurate determinations of the thermal data. The heat of formation of the chloride was similarly observed to be -256.18 ± 0.28 kcal per mole. Heats of solution and combustion of lanthanum metal yield mutually concordant results, and earlier discrepancies reported in the literature may be ascribed to impurities.

Jan 1, 1959

By Terry J. Close

A mineral resource survey of the 940-square-mile (2,434 km2) Hells Canyon study area, which includes Hells Canyon Wilderness, Snake and Rapid Wild and Scenic River's, and adjoining roadless lands in Oregon and Idaho, indicates the area is highly mineralized. Thirty-four lode deposits within the study area have resources totaling about 31 million tons (28 million t) containing copper, silver, zinc, gold, and lead; another 42 lodes, not sufficiently exposed to allow resource estimates, are believed to have mineral potential. The most important deposits are copper-, silver-, zinc-, gold-, and lead-bearing volcanogenic occurrences, followed by silver-and copper-bearing contact replacement (tactite) deposits; other lode occurrences are relatively unimportant. The most important placer deposits occur at Dry Diggins; placers along the Snake River are small and scattered. The study area has extensive deposits of limestone and sand and gravel; it has little potential for energy resources.

Jan 1, 1982

By Nathan T. Lowe

This report updates an accounting of mines and prospects in the Seafoam mining district, Custer County, Idaho, begun during mineral appraisal of the Idaho Primitive Area. Thirty-two mine and prospect locations have been added to the Bureau's Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of mineral appraisal of the River of No Return Wilderness; most previously known locations were field checked and the updated information added to the data base. The district's major deposits include polymetallic fissure veins of gold-silver-lead-zinc-copper hosted by granodiorite and quartz monzonite which have been intruded by dikes ranging in composition from rhyolite to dacite, and vein type replacements of silver-lead-zinc-copper hosted by calcareous xenoliths imbedded in major intrusives. These deposits may be related to the intrusion of the Rapid River pluton or the Casto pluton. The dominant northwest structural trend is parallel to an aeromagnetic high, a weak gravity salient, and the Blue Bunch Mountain dike swarm.

Jan 1, 1983

By Steven J. Page

Overexposure to airborne respirable crystalline silica dust can cause disabling or fatal respiratory disease, and mine worker exposure to silica dust continues to be an ongoing occupational health concern. Exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern. On surface coal mine drills, bailing air flushes the cuttings out of the drill hole. Conveyor belting material is typically used to fabricate a shroud around the drill deck in an effort to contain the drill dust so that it can be captured by a collector. Dust leakage from the drill shroud is usually the worst dust source problem on most drills. The focus of this work is drill shroud dust leakage and the relationships of various drill parameters on this leakage. Experimental data were obtained and used in combination with dimensional analysis to establish these relationships. In general, it is found that airborne respirable dust (ARD) concentrations vary in a direct relationship with shroud leakage area and in an inverse relationship with drill deck cross sectional area and shroud height. This work expands the testing and dimensional analysis previously reported for collector/bailing air flow ratios ranging from 2:1 to 4:1 to include ratios approaching 1:1. A semi empirical mathematical model has been developed and expanded to describe ARD generation on surface coal mine drills. Geometric parameters included are drill deck height and cross sectional area, shroud leakage associated with the deck shroud, and the operational parameters of bailing airflow and dust collector airflow. The relationships can be described by logarithmic functions and yield predictive ARD values, which fall in the range measured on operating drills for collector/bailing air flow ratios greater than 2. However, at values of collector/bailing air flow ratios of approximately 1.1, the amount of ARD shows minimal response, if any, to drill deck shroud improvements that do not result in near perfect seals. This is a condition that can occur in actual operation and is a substantially different result than previously expected and reported. Application of these results should provide mine operators with sufficient information to determine (1) the relative magnitude of their dust emissions, (2) where they should focus their efforts to reduce ARD emissions and (3) the improvement they could reasonably expect to achieve. Given that exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern, substantial reductions of airborne silica dust during drilling may be estimated and achieved through use of the analysis presented. Keywords: drill; dust; model; dimensional analysis

Jan 1, 2008

By D. C. Fleck

Electrorefining yttrium from selected low-melting yttrium--base alloys is investigated, and various halide systems are studied as potential electrolytes for use in preparing low-oxygen yttrium by electrorefining unalloyed yttrium. Yttrium cathode products having significantly less metallic impurities than the anode materials were prepared from alloys containing nickel, iron, and manganese by electrorefining in LiCl-YC13 electrolytes at 900° to 1,000° C. Yttrium-copper and yttrium-magnesium alloys are not suitable as anode feed materials, An evaluation of chloride, fluoride, bromide, and mixed chloride-fluoride electrolytes showed that cathode products containing much less oxygen than the anode material can be obtained in the fluoride and mixed chloride-fluoride systems. Initial cathode current density has no apparent effect on the purity of the products obtained in both phases of the investigation.

Jan 1, 1973

In 2007, a total of 7,199 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 ? Sand and gravel mines were the largest mining sector, comprising 48.4% of all mining operations. ? Sand and gravel mines were found throughout all 50 states and Puerto Rico.

Aug 1, 2009

Develop methods to detect and repair poorly functioning dust collectors on roof bolters. Approach In conjunction with a research project to reduce silica dust in coal mines, a variety of roof bolting machines operating under different conditions were examined to find out how much these machines were contributing to the silica dust problem. Results The investigation concluded that if the bolting machines' dust collector is properly maintained, very little dust can be measured in the air, even with minimal airflow over the bolter. Poor maintenance, however, frequently results in high dust levels. Three major problem areas were found. These were: (1) filter leaks, which allowed dust to escape, (2) accumulations of dust in the collection system, and (3) low airflow at the bit due to hose, fitting, and relief valve leaks.

Jan 1, 1984

By M. Clair Smith

This report is one of a series describing exploration, development, mining, and processing of mineral deposits in the United States. The reports are prepared and published by the Bureau of Mines in cooperation with various mining companies The purpose of the reports is to promote development and conservation of our natural reserves by disseminating technological information on mining and milling procedures and related practices at operating mines. Simplot Silica Products, Inc., mines and processes a friable silica sandstone. The finished products are sold for use in glass manufacture, foundries, chemicals, and special applications.

Jan 1, 1959

By Charles F. Jackson

Waste filling has been employed for many years for supporting the walls of stopes and preventing failure and subsidence of the surrounding and overlying rock formations, and its effectiveness for this purpose has long been recognized. It is used for permanent support in ground where timbering (including square-setting) is inadequate for more than temporarily supporting the walls of the excavations. It should be rioted, however, that effective as a good, solid fill may be in resisting heavy side pressure and direct weight, its usefulness for supporting large areas of back and preventing breaking and movement of the overlying rocks is limited. Even the strongest and most uniform rocks will break if the unsupported span becomes too great; and since filling cannot be packed tightly against a horizontal back there is always a possibility of the back breaking and consequent subsidence if the maximum self-supporting span is exceeded. Planes of separation, such as bedding and fault planes, slips, and joints, are common in all rock masses; these may occur above the stoping area where their presence cannot be ascertained by observation. If too much reliance is placed upon filling for the support of a large horizontal area of back (as contrasted to support of vertical or steeply inclined walls) large masses of rock may break along a. plane of weakness, compress the fill, and leave an open space into which caving of the overlying rocks may continue until the space is filled. In this paper the term "waste filling" includes any filling material other than ore - waste mine rock, rock from surface quarries or opencuts, sand and gravel, mill sands, or slags from smelting operations.

Jan 1, 1935

By P. G. Barnard

The Nation's steel industry is largely dependent on shipments of manganese from foreign sources for steel production. An adequate substitute for the manganese requirements of our present steel technology would improve our national self-sufficiency and also contribute substantially to the conservation of our manganese resources. As each of these objectives is a major interest of the Bureau of Mines, possible substitutes for manganese in steel were investigated. Titanium was selected as the most promising substitute because the published results of several investigations indicate that titanium would perform the most obvious function of the manganese in steel: The elimination of iron sulfide and its deleterious effects. The investigation involved extending the published data on titanium additions in steel to provide enough information for an accurate evaluation of the practical value of the substitute. Therefore, quantitative data were obtained on the partition of sulfur and carbon between iron and relatively small titanium additions.

Jan 1, 1962

By Oliver Bowles

Enormous quantities of limestone are used for metallurgical purposes. Approximately 23 million tons were so used in the United States in 1925 chiefly for smelting iron ores in the blast furnace. Smaller amounts are used in basic open-hearth steel manufacture, and in smelting lead, copper and antimony ores. Most limestone producers lave little knowledge of the way in which their stone is used in metallurgy. Maximum tolerances of silica, alumina, sulphur and possibly magnesium; and minimum content of calcium carbonate may be arbitrarily fixed for the guidance of the producer, but aside from these requirements little information is available to producers on the manner in which their stone is used, the office it performs in smelting, or the effects of impurities. More complete [wledge] of utilization would enable limestone operators to solve their production problems more intelligently.

Jan 1, 1927

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 3 Principle Program Nomenclature The principal variable names used in the computer program are defined below. The following dimensions are applicable, unless otherwise indicated. Distance - Ft Velocity - Ft. /Minute Time - Minute

Jan 1, 1976

By R. W. Watson

This Bureau of Mines report summarizes some recent results on the sensitivity of various experimental explosive systems using ammonium nitrate (AN) as the oxidizing agent. The sensitivity survey included drop-weight and friction testing and sensitivity to initiation by projectile impact and a No.8 blasting cap. It was found that certain types of AN prills can result in cap-sensitive mixtures when combined with No.2 diesel fuel (Fa); prilled AN mixed with nitromethane also result in cap-sensitive mixtures. Mixtures of AN prills and neat 1-and 2-nitropropane were not cap-sensitive, and the use of powdered or grained aluminum in AN-FO did not adversely affect the sensitivity except possibly to increase its sensitivity to friction.

Jan 1, 1974

Design, fabricate, and test a machine capable of operating in coal seams 48-inches and thicker that can reduce the time, expense, and injury potential inherent in extending and retracting mine-wide section belt conveyors, while eliminating the need to use additional machinery or equipment in accomplishing such moves. The Problem Many underground coal mines use a belt haulage system to move cut coal from the face to the loading area. This system usually consists of a main line belt conveyor fed by section belt conveyors. A shuttle car at the face carries the coal cut by a continuous mining machine to a feeder breaker that breaks the large lumps of coal into smaller, transport-able pieces and unloads them onto the tail piece of the section conveyor. This tail piece is skid-mounted so it can be readily moved as needed. The conveyor is kept close to the face during mining in order to shorten the haul distance of the shuttle cars. Section belts can be lengthened by adding belting, wire rope, and support hard-ware. During pillar retreat mining, these section belts are shortened to keep pace with pillar extraction operations. However, these belt moves, either the extensions or retractions, usually require six to eight workers and three to eight hours to complete. In addition, a 100-foot belt move requires workers to handle up to 4,000 lbs. of material, not including the tail section. Strain and sprain injuries can be incurred during this heavily labor-intensive task. The time required to move the section belt can also create losses in the mine's production. To help solve this problem, the Bureau of Mines

Jan 1, 1984

By Karl R. Becker

Detonators representing a sampling of various domestic commercial delay detonators were fired at various direct-current (dc) firing levels. Results of firings using well-below-recommended firing levels showed marked increases in delay times above the nominal values. There was also a marked increase in variation, to the extent that out-of-sequence firings would be essentially assured in any typical blasting round at these low firing levels. Within the range of recommended levels the effects of current increases were not considered to be of great importance relative to other overriding effects, such as the significant difference noted in average values of detonators from different lots having the same nominal delay. This effect, when combined with the normal variation noted among members from the same lot, would cause out-of-sequence firings with detonators from a neighboring delay period. Where comparisons with results from another study were possible, it was found that both studies observed quite similar variations in delay times about the average values, and a lower probability of out-of-sequence firings for the shorter delay period groups. The criterion of the previous study for assessing the likelihood of observing out-of-sequence firings, when applied to the Bureau of Mines data, properly identified two neighboring delay period groups where out-of-sequence firings would occur.

Jan 1, 1981

By G. R. Hopkins

[Apparent progress in fuel economy at petroleum refineries, as measured by the average amount of .seat units required to refine a barrel of crude oil, received a set-back in 1935, when the average rose to 562,00 B. t. u., compared with 562,000 B.t.u. in 1937 (see fig. l). The primary factor in the rise in average heat requirement's per barrel of crude oil refined in 1938 wan the decline in total runs to Invariably the average requirement increases when crude ins to stills decline, and vice versa. In other words, annual gains in fuel efficiency at refineries arc masked by the degree to which the capacity is utilized. Additional crude runs give lower average e heat requirements in two ways - first, because they are mane with the c expenditure of comparatively small amounts of auxiliary heat, and, second, because the additional runs generally represent simple topping operations. In 1938 crude runs, to stills declined 1.6 percent (from 1,183,440,000 barrels in 1937 to 1,165,015,000 barrels in 1938), but the total heat consumption declined only 0.4 percent, or from 663,866 billion B. t. u. in 1777 to 660, 56 billion in 1938 .]

Jan 1, 1939

By Lester G. Morrell

THE WORLDWIDE economic expansion that has characterized the first 3 years of the 1960's continued through 1964 and was reflected in North America by strength in the industrial economy of the United States, which again was dominant. Advances in production were recorded in virtually all industries, including the mineral industry; 1964 mineral production established a new high, 5.4 percent above the previous peak recorded in 1963. However, the percentage increase in value of North American mineral production was slightly below overall economic growth. For industry in general, consumer demand held firm throughout the year and overall commodity prices averaged 2 percent higher than in 1963. Wages and salary payments also were up. With the single exception of the dock strike in the United States, the year was free of serious labor troubles and unemployment in both Canada and the States was at a low level. Despite the Viet-Nam situation, relatively tranquil international relations contributed to the forward movement of North American business. Total gross national product (GNP) for Canada and United States, in current dollars, was estimated at US$672.2 billion; 6.8 percent above the previous year's figure. Combined national income in 1964 amounted to US$546.9 billion, which was nearly 7.0 percent more than in 1963. In 1964, gains were recorded in each of more than 50 metals, nonmetals, and fuels commodities that comprise the North American output. The greatest category increase was 13 percent in metals, which was in part attributable to the 14 percent rise to a new record in value of iron and steel in United States, a 29 percent higher value of Canadian iron ore and a 57 percent rise in Canadian zinc. Despite a moderate decline in prices of iron ore and iron and steel products, generally favorable markets and rising prices for metallic ores and metals were a stimulant to the metals industry. Nonmetallic materials, with a total value in excess of US$5.25 billion were 7.3 percent higher than in 1963. High levels of highway and building construction and expanding demand for fertilizers and chemicals continued throughout the year. Noteworthy output increases were recorded for lime,

Jan 1, 1966

By R. G. Knickerbocker, T. E. Evans, J. L. Morning, D. R. Torgeson, F. W. Wessel

"INTRODUCTION Pilot-plant studies on processes for converting low-grade domestic manganese ore to high-grade oxide or sulfide products by pyrometailurgical process was initiated at the Boulder City, Nev., Experiment Station in 1942. These investigations were given impetus by the possibility of a national shortage of ferro-grade manganese oxide for war needs.The manganese ore employed-in most of the pilot-plant smelting tests was from the manganosiderite-nodule deposits at Chamberlain, S. Dak. This deposit although low-grade, is extensive and represents, the largest reserve of manganese in continental United States. 6/ The Bureau of Mines has recently developed a Carryall mining-conical rolls treatment method that shows promise of making possible economic removal and subsequent beneficiation of the nodule-bearing shales. 7/ Smelting tests were made also on Artillery Peak, Ariz., mill concentrates in the productions of unrefined manganese matte for the steel The pilot-plant smelting program was based upon the fundamental fact that manganese, like copper, will sulfidize and become miscible with FeS. The matte this formed represents the initial smelting step in the pyrometallurgical treatment of the beneficiated ore. The concentrated nodules containing about. 18 percent manganese were smelted with varying amounts of pyrites and appropriate fluxes to produce Mns-FeS mattes containing 16 to 50 percent manganese. When the manganese and iron was completely sulfidized, the mattes contained 16 to 23 percent manganese. Reducing the pyrite resulted, of course, in the selective sulfidization of manganese and the production of a matte containing a correspondingly higher ratio of MnS to FeS. Complete sulfidization smelting produced slags of lower manganese content and hence resulted in higher manganese recoveries in the matte."

Sep 1, 1946