Search Documents

By William A. Beck

Since bauxite mining began in the Irwinton District, Wilkinson County, Ga., in 1912, it has been on a small scale, as most of the deposits of high-grade ore are small. The bauxite has a high silica content, and its use has been largely limited to the chemical industry. Drilling under this project did not disclose any bauxite deposits of commercial value: However, numerous holes penetrated high-alumina clay deposits, but no attempt was made to delimit them, as the project was solely an exploration for bauxite. Bauxite was first discovered near Irwinton in 1907. The district covers virtually all of Wilkinson County and extends into the adjoining counties of Washington, Baldwin, and Twiggs. Mining was begun in 1912 by the Republic Mining & Manufacturing Co. on the Honeycutt, Parker, and Daniel properties, which are 1.5 miles from Wriley on the old Irwinton to Milledgeville Road.

Jan 1, 1949

By M. J. Kovalik

The effects of the process variables on the production of chemical coke on a chain grate stoker, a type of traveling grate, were studied. Six bituminous coals, ranging in volatile matter from 16.7 to 43.8 percent, were successfully carbonized, yielding chemical coke with acceptable physical properties. The coke yields were dependent on the volatile-matter content of the coal. The air fuel ratio had the most marked effect on the yield and characteristics of the resultant coke, and the general furnace performance. Results can only be predicted; the actual yield and quality of coke obtained from any given coal can only be determined by actual tests using the optimum processing variables to obtain a coke with minimum volatile-matter content and to retain as much of the fixed carbon in the original coal as possible.

Jan 1, 1967

By Oren C. Baptist

Umiat field contains the largest accumulation of oil discovered so far in Naval Petroleum Reserve No. 4 in Arctic Alaska. The Umiat anticline was tested with 11 wells; 6 produced oil in varying quantities. Behavior of the wells during testing was unpredictable. For example, one well was abandoned as a dry hole after all tests failed to recover any oil, yet an offset well, only 200 feet from the dry hole, produced 400 barrels of oil a day. The main oil reservoirs are less than 1,000 feet deep and are in the permanently frozen zone (permafrost). Reservoir pressures are low, and most primary production will be by expansion of gas-in-solution in the oil. Because of the unusual reservoir conditions and the difficulties encountered in drilling and completing the wells, the Department of the Navy asked the Federal Bureau of Mines to make laboratory studies of the reservoir sand to determine the cause of well plugging and to provide laboratory information, to be used as an aid in estimating oil recovery from frozen reservoir rocks under solution-gas expansion from low-saturation pressure conditions.

Jan 1, 1960

By Don Belsher

Work on contract H0272007 is summarized for the period of 1 February 977 to 1 February 1978. The initial evaluation of two potential systems for the location of well casings, voids, and tunnels in coal are described. The pulse measurement equipment used for the evaluation of the antennas selected possible use with a pulse time domain system and an FM-CW system is described. A TEM horn antenna design potentially suitable for use with these systems is given. An operational comparative analysis between various antenna types is presented.

Jan 1, 1978

By Gerrit V. R. Goodman

In This Chapter [Design and operation of machine-mounted scrubbers Dust control with scrubbers and blowing ventilation Dust control with scrubbers and exhaust ventilation Dust control with exhaust ventilation and no scrubber Dust control methods common to all continuous miner sections Dust control for roof bolters] This chapter explains how to control dust at continuous miner sections in coal mines where the main dust sources are continuous miners and roof bolters. In relation to dust, there are three categories of continuous miner faces depending on the type of ventilation and whether or not a machine-mounted dust scrubber is used. These are— 1. Mining machines with dust scrubbers used with blowing face ventilation 2. Mining machines with dust scrubbers used with exhaust face ventilation 3. Mining machines without scrubbers used with exhaust face ventilation The approach to dust control is somewhat different in all three of these. However, there are many dust control features (such as the need to provide adequate airflow) common to all continuous miner sections. For workers at roof bolter faces, there are two dust sources: 1. Dust from the continuous miner when it is upwind. 2. A malfunctioning dust collector on the bolter, which allows dust to escape DESIGN AND OPERATION OF MACHINE-MOUNTED SCRUBBERS [Almost all new continuous miners are equipped with scrubbers. When the dust is excessive, it is possible that the scrubber needs some maintenance.]

Jan 6, 2003

By Alfred Bellows

The objective was to develop and design a remotely operated temporary roof support system that provides a safe working environment between a freshly cut coal face and the last line of permanently supported roof in which to perform roof bolting activities. This system was to take the form of a retrofit package which could be adapted to a majority of the bolters currently in service. The result is an integrated piece of hardware which will retrofit onto virtually all single boom bolters by removing the drill boom and relocating and modifying the hydraulic controls. The system is composed of three basic components: a pair of cantilevered roof supports which reach forward to the desired line of support, a mast type drill unit for drilling holes and torquing bolts, and a transverse slide assembly to carry the drill from hole to hole across the entry without relocating either the bolter or the roof support. A converted bolter not only provides a much safer operation but is projected to increase the production speed as well as reduce the manpower required to operate a section.. This improvement in productivity is shown to make the job of retrofitting a bolter cost effective in less than two months and provide a potential profit thereafter. Based on the findings presented in this report it is recommended that a proto-type be built and tested in an underground coal mine to demonstrate its effectiveness.

Jan 1, 1976

By Steven J. Schatzel

Gas drainage through surface bore-holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwalls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole intercepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain-age during longwall mining will be essential for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European techniques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

By L. F. Heising

Ten composite samples of Mesabi Range nonmagnetic taconite from the Hibbing, Minn., area were evaluated by flotation and by reduction roasting-magnetic separation to determine their potential as a future source of iron are. Only one of the composites yielded concentrates that could be considered marketable, using as a criterion a 10-to-1 iron-to-silica ratio. Cursory petrographic examinations of all 10 composited samples and a detailed mineralogical study on 1 sample suggest that unfavorable mineralogical associations between iron and gangue minerals are responsible for their poor beneficiation characteristics.

Jan 1, 1967

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 52 to 3,443 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

By Charles Vaught

This paper discusses the fact that US coal mining organisations are losing the knowledge they need in order to be able to respond to emergencies. The authors note that knowledge management provides a useful perspective from which to view the problem, but that the debate about what constitutes knowledge should be broadened to include a debate about what constitutes management. It is argued here that knowledge is actually shared knowing distributed across group members; that such knowledge can be managed by cultivating it; and that narrative is the medium through which this may be done. The paper then examines NIOSH research that has attempted to use such an alternative knowledge management approach to help potential mine emergency responders better deal with the predicaments they are likely to encounter on-site.

Jan 1, 2006

By R. C. Corey

GERMANIUM is an element that has come into widespread use in the electronics industry in recent, years. So far this increasing demand has been, met by ample supply: however, the future balance is uncertain, and the need has been recognized to discover additional domestic sources of germanium. This investigation was conducted to study the possibility of obtaining a potential supply of germanium from coal or coal ash. It has been known for some time that coal contains germanium; the discovery that By ash from coal-fired boilers often contains appreciably more germanium than the original coal suggested the possibility that coal ash might be an abundant and economical source of this element. In this study the concentration of germanium was determined in numerous samples of coal and ash. A number of miscellaneous waste materials also were examined in the course of the investigation; the results are reported as a matter of general interest. The methods and equipment employed are discussed in detail. Sample-preparation and analytical techniques are described in the appendix. Spectrographic analyses were made on a total of 639 samples, including coal, coal ash, slap ash from lignite and peat, wood ash, and various inorganic materials. Qualitative analyses were run on all samples, and quantitative determinations were made on those samples that contained enough germanium to be measured by this method The lower limit at which germanium can be determined quantitatively by spectrographic analysis is 50 parts per million (p. p. m.), but concentrations of less than 20 p. p. m. can be detected qualitatively.

Jan 1, 1959

By H. M. Thorne

Oil shale, a potential source of products presently obtained from petroleum, is found in many countries. The most extensive known deposits from the standpoint of potential shale oil in place are those in Brazil and the United States of America. Mining methods used for oil shale range from open-pit operations for shallow deposits to room-and-pillar and longwall techniques for deposits with thick overburdens. Oil shales from different sources vary greatly in the amounts and types of organic and inorganic constituents. By retorting, the organic material is converted to oil, gas, and coke. The largest percentages of oil are obtained from materials having the highest hydrogen content. Over 2,000 retorting systems have been patented, but only a few have been used industrially, and no single process seems best for all types of shales or economic conditions. Shale oils have different characteristics, depending on the source rock and method of retorting. They contain large quantities of olefinic hydrocarbons and more oxygen, nitrogen, and sulfur derivatives of hydrocarbons than most petroleums. Consequently, petroleum refining methods usually must be modified for shale oil. This is particularly true in catalytic processing. Hydrogenation, even under mild conditions, improves shale-oil refinability. Several byproducts may be obtained from both the retorting and refining steps.

Jan 1, 1964

By Frank E. Williams

Nuclear detonation data were accumulated, studied, and evaluated by the Bureau of Mines to visualize how nuclear explosives might be used in a shale?-oil industry, The evaluation shows that the Green River Formation at the semi-isolated locale of Piceance Creek Basin, in northwestern Colorado; is thick and widespread enough to warrant consideration of nuclear mining in lieu of conventional methods, Because cost data for nuclear explosions are limited; cost comparisons are made largely by assumptions. Also described are the history of the shale-oil industry, the geology and size of oil-shale resources; and conventional mining methods and processing technology.

Jan 1, 1969

By C. H. Elder

Two degasification test boreholes were drilled to depths of 1,238 and 1,212 feet on Bureau of Mines property at Bruceton, Pa., as part of the Bureau's long-range coal degasification program. The holes provided detailed geologic information and geologic sections, which were correlated with regional stratigraphic cross sections prepared by the Pennsylvania Geological Survey. Gas content determinations and coal analyses were made on the Upper Freeport, Middle Kittanning, Clarion, Brookville, and Mercer coalbeds; gas content of the coalbeds ranged from 53 to 165 cubic feet per ton. Formation pressure and gas flow tests were conducted on selected coalbed intervals in borehole 1; formation pressures ranged from 292 to 473 psig. The middle Kittanning coalbed was hydraulically stimulated using very heavy gelled water, but gas production remained low because gel residue and formation water inhibited the flow of gas. Gas contents in the Clarion, Upper Brookville, and Mercer coalbeds were anomalously low owing to the proximity of porous sand-stones which act as reservoirs for gas migrating from coalbeds.

Jan 1, 1977

Although the mining industry has achieved record-low fatalities and injuries for each of the last three years, there are still too many miners injured or killed in this nation ís mining operations. Many mining injuries or deaths might have been prevented by using risk assessment to identify and control or eliminate the hazards associated with a task. To focus attention on the importance of conducting risk assessments in keeping mining workplaces safe and healthful, MSHA introduced this initiative on October 12, 2004. This initiative is called SLAM. SLAM is an acronym for Stop, Look, Analyze, and Manage. The steps involved in SLAM are: Stop ñ stop and consider the work involved Look ñ look for and identify the hazards Analyze ñ analyze what needs to be done Manage ñ manage safety by developing and implementing controls Everyone should be aware of the risks of an accident before beginning a task. It may not always be obvious that performing a seemingly routine task could result in an accident. That is why conducting a risk assessment is so important. Itís important to remember that over time a mining workplace seldom remains unchanged. Risks must be assessed whenever procedures or processes change, whenever new tasks are started, or non-routine tasks are performed.

Jan 1, 2005

The objective of this handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface metal and nonmetal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. Portions of the handbook that should prove most useful to the inspectors include a survey check list, rules for determining if sampling is required, list of most frequently encountered contaminants, list of candidate contaminants and their sampling conditions, interpretation of results, and a procedure for a health and safety inspection.

Jan 1, 2011

By G. E. McElroy, A. S. Richardson

"The Bureau of Mines, in cooperation with the Anaconda Copper Mining Co., has conducted a series of experiments an air measurement in fan-pipe installa¬tions in a Butte mine during the fall and winter of 1922-3. The chief purpose was to determine the friction factors for different types and sizes 3f fan piping, but much attention was devoted to methods of air measurement, not only with respect to the methods used for friction factor tests, but also to com¬parison with other methods.The air flow was measured simultaneously at two points 380.6 feet apart in six different fan-pipe installations, each over 500 feet in overall length, in a rock cross cut adjacent to an air shaft,The air pressure was regulated by two sinoco multivane fans, driven by 7 ½ h.p. motors, the fans being connected in tandem so that one discharged into the intake of the other through a short connector and the latter discharged into the line through a straight connection equipped with a honeycomb of 4-inch squares or S radial vanes to prevent spiral flow of air, At each point where it was desired to measure the air flow, measuring sections equipped with piezometer rings pierced for easy insertion of pitot tubes, thermometers, etc. Piezometer static pressures were used in all the tests as standard, and dynamic or total pressures only were obtained with the pitot tubes, except for purposes of comparison.The tubes had special guide blocks, designed especially for underground work. To insure greater accuracy two tubes were used simultaneously, in order to obtain the velocity pressure at the center of the section simultaneously with that nearer the circumference, so that the mean velocity would be determined as accurately as possible. The tubes were held in proper place by means of flat guide boards. Velocity pressures were measured in manometers."

Sep 1, 1923

By Lung Cheng

Based on earlier tests that showed steel to be much more likely to cause frictional ignition than tungsten carbide, the Bureau of Mines redesigned coal-cutting bits to reduce the hazard of face ignitions. Two bit designs--a mushroom-shaped bit with a conical shank and a dove-tail bit with a rectangular shank--are described, as well as bit wear tests conducted in the laboratory and in an operating coal mine. In laboratory tests, for 1/8-, 1/4-, and 1/2-in-deep cuts and cutting speeds of 280, 500, and 660 ft/min, the mushroom bit had significantly longer tip wear life than the conventional bit; the dovetail bit was also superior to the conventional bit. Results of in-mine tests on the mushroom bit agree well with laboratory results. In-mine tests of the dovetail bit are underway.

Jan 1, 1983

By H. Dale Nichols

[The growing importance of the Sundence (Jurassic) formation an a source of oil, in the Rocky Mountain area has prompted the making of a series of porosity determinations of core samples collected. from the reservoir sands of the Lance Creek oil field, Niobrara. County, Wyo. These analyses are preliminary to a stud of fluid and energy relations in the Basal Sundance reservoir of that field, and the determinations of porosity will be used in subsequent studies requiring, calculations of the volumetric capacity of the reservoir and estimation of the reserves of oil and gas. However, the porosity characteristics an of the Sundance sands in the Lance Creek field are factory that affect the solution of many current practical problems of development and operation. Primarily for that reason but also because it is recognized that porosity values of different oil-production sands are of widespread interest throughout the industry, the results of the initial work have been presented in tabular and graphic form with no attempt to evaluate their significance as they relate to the production history of the field.]

Jan 1, 1938

By R. J. Hundhausen

This report describes the exploration and recent utilization studies the Bureau of Mines conducted on the Iron King, Chambers, and Dry Camp chromite deposits in the John Day district, Grant County, Oreg. The field investigations were undertaken during parts of 1939 and 1942 to determine the tonnage and grade of chromite in the district that could be utilized as a war reserve for the steel industry. As a result of the Bureau's field work, which included construction of 9 miles of access road, 6,204 feet of diamond drilling, 195 channel samples, and 1,020 linear feet of trenching, an ore reserve of 208,000 tons of 22-percent chromic oxide was indicated in the 3 deposits. Less than 1,000 tons of this ore has been mined since the field work was completed because the 2 largest deposits are submarginal in grade and there is as yet no incentive to develop and mine the ore. Since the war, however, the Bureau has been seeking means of utilizing the ore. Two methods of utilization that show promise are direct smelting of the ore in an electric furnace and use of the chromite for making refractory brick.

Jan 1, 1956