Search Documents

By Irving Hartmann, John Nagy, Donald Mitchell

"SUMMARY AND CONCLUSIONThe test data indicate that water infusion of the Pittsburgh coal seam does not reduce the amount of fine dust produced during mining operations to the extent reported elsewhere. Wide variations in the amounts of dust collected in the air current were noted in duplicate samples and repetitive tests. Changes in depth and location of the infusion holes and amount of water injected and addition of a wetting agent to the water had little effect on the amount of dust liberated.Water was forced readily into the coal. Some water flowed out along the cleats, but an appreciable amount remained in the seam. Little or no water pene¬trated the coal seam above the upper infusion holes.The average dust concentration (with and without infusion) in the return air, 40 feet outby the working face, was 25 million particles per cubic foot during undercutting, 20 million during drilling, 75 million during shot firing, and 20 million during hand loading. At the working face the average concentration was 3 to 6 times higher. The concentrations were measured at an airflow of 1,600 cubic feet per minute (c.f.m.) at the face.On the basis of this short investigation, no final conclusions can be made on the effectiveness of water infusion in reducing the amount of fine dust liberated during mining in the Pittsburgh coal seam. However, the data indicate that dust reduction resulting from infusion would be small.INTRODUCTIONThe production of fine coal dust is an inherent part of nearly every phase of mining. The use of large, high-speed continuous-mining machines and other mechanical equipment has increased dust production. In addition, in coal seams that have been subjected to high pressures for a long period, and particularly in dry and friable seams, some very fine dust is in the seam before mining. Much effort has been devoted to allaying and collecting at its source the fine coal dust released during mining. One of the comparatively recent techniques that has been developed for this purpose is infusion of water or other liquids into the coal seam. This method consists of injecting water under pressure into a coal seam to neutralize the fine dust released during mining. The water generally is introduced through bore holes in the face before undercutting."

Jul 1, 1957

By Eugene H. Skinner

This Bureau of Mines report describes the fieldwork and subsequent analysis to determine physical properties, stress distribution, and several aspects of rock behavior as a necessary evaluation for a typical mine opening. All work was done at a test site on the 3300 level, Crescent mine, Coeur d'Alene mining district, Idaho. Free field stress beyond the influence of the opening was also determined. Conventional overcore technique with the three-component borehole deformation gage developed by the Bureau of Mines was used in three drill holes. Three field verification tests were performed using a gage newly developed by the Spokane Mining Research Center in an approach herein termed "initial deformation method." Use of this method validated that aspect of overcore theory which predicts that similar deformation effect occurs in the wall rock around the perimeter of an opening in rock under stress. Also described are all drilling procedures and performances. Physical property determinations were made on rock samples obtained from the three overcore drill holes. Twelve physical properties with a total of [532] values were obtained at various drill hole orientations and depths. Exhaustive statistical tests were utilized in the analysis of these physical properties. Further elaborated are statistical inferences based on these analyses. Extensive analysis and interpretation of Crescent mine geology are also described.

Jan 1, 1974

By S. J. Schatzel, J. Cervik, A. A. Campoli

The cross-measure borehole technique is being studied by the Bureau of Mines as an alternative to the use of surface gob boreholes as a means of controlling methane in gobs during longwall mining. Small-diameter holes are drilled from underground locations into strata overlying the mined coalbed. When the roof strata are fractured by the mining opera- tion, a partial vacuum applied to the boreholes draws the methane out of the fractured strata and prevents it from entering the mine ventilation system. Tests in the Upper Kittanning Coalbed showed that 50 pct of the methane produced by the longwall mining operation was captured by the cross-measure boreholes. Borehole inclination and penetration into the gob are two important borehole parameters that affect the performance of the cross-measure borehole system.

Jan 1, 1983

By C. H. Johnson

The Big Jim mine of the United Eastern Mining Co. is at Oatman, Mohave County, Ariz. Oatman is in the foothills on the western side of the Black Mountains, at an elevation of about 3,000 feet. It is on a paved highway about 30 miles west of Kingman, the principal distributing; center for mining supplies in the district, and 25 miles from Topock, en the Colorado River. Both latter towns are stations on the Santa Fe Railroad; Oatman has no roil connection. Mining conditions are typical of western Arizona; water is scarce, no mine timber is available locally, and the winters arc mild and the summers hot. The supply of a killed labor is usually adequate, but in 1933-34 it w not more than sufficient for the restricted operations. Wages have been $4.00 to $4.50 for miners. Electric power was supplied from Kingman and cost about 2.6 cents per kilowatt-hour.

Jan 1, 1935

By David R. Alison

This study was conducted using field interview methods to determine the data and information requirements of the underground coal mining industry for improving mine ground control procedures in existing and future mines. The establishment of a central geologic and engineering information resource center with computer searchable abstract files that can locate and supply descriptive and case-study literature addressing specific mining problems is recommended. Research done under Bureau of Mines Contract J0395010, includes a Bibliography of Underground Coal Mine Ground Control Literature.

Jan 1, 1980

By E. H. Izen

A thermal imaging borehole probe was designed and fabricated for the purpose of obtaining thermal images, through smoke, of objects and people in underground mines. The effort was basically unsuccessful; electrical noise, and possibly thermal noise, interferred with the desired signals to the extent that spatial resolution in the images was unacceptable.

Jan 1, 1980

By Russell J. Miller

A high-pressure intensifier system was designed, constructed and field tested as part of a program to determining the feasibility of applying high-pressure water jets on conventional mechanical rock excavation equipment to increase advance rates. Also developed were a high-volume swivel, capable of transferring the high-pressure water to a rotating cutterhead and manifold system for locating and protecting the jets on the cutterhead. Field tests were conducted in a granite quarry near Skykomish, WA, approximately 90 miles east of Seattle. The concept of improving excavation rates by using water jets to assist mechanical cutting was proven to be successful, with an average increase in excavation mete of 50 to 60%. For some tests, the excavation rate was more than doubled. Machine torque requirements were reduced approximately 25% when the water jets were used. It was suggested this was due to reduced cutterhead friction in the presence of the water jets. A comprehensive economic analysis was undertaken as part of a concurrent study to determine the degree of cost benefits attainable from increased advance rates. Very significant savings were seen to be possible. It was concluded that the basic concept of combining a water jet capability with a mechanical excavating machine is definitely possible.

Jan 1, 1976

By Jon G. Bredeson

The electromagnetic noise that exists in a mining environment is quite severe and was shown to have been reasonably well documented by a number of researchers in the Phase I Report. The noise levels are such that prudent communication design requires the careful use of all the electromagnetic noise data available. A comprehensive survey was undertaken to determine techniques used in various industrial environments to achieve secure communications in the presence of electromagnetic interference. The techniques were given in the Phase I Report and are rudimentary, but have produced reasonably good results. A number of these techniques could be applied to the mining environment.

Jan 1, 1980

By William R. Wessels

This report describes a field survey and laboratory investigation into the causes of failure of resiliently clad screen decks applied to coal preparation plants. Blinding of screen deck perforations and delamination of the resilient cladding are studied and mechanisms responsible for these failure modes are hypothesized. A laboratory test program to simulate the mechanisms was begun and abandoned when it became apparent that meaningful test results would require a substantially redirected effort. No meaningful test data was obtained from the laboratory simulation.

Jan 1, 1982

By William N. Patterson

This report describes the design and testing of an improved quiet hard rock percussion drill. The improved drill incorporates a tappetless design with independent rotation in a hand held drill weighing 50 lbm. Laboratory and field testing in three mines were conducted. The testing showed improved drilling performance with no increase in measured noise levels over the fist design.

Jan 1, 1985

By Daniel C. Boteler

Data from 68 entrained-bed carbonization tests were treated statistically by the Bureau of Mines, and several useful relationships were developed among the major variables. Nine coals, ranging in rank from lignite A to high-volatile A bituminous, were carbonized in two entrained-bed carbonization pilot plants. The carbonizing reactors employed were vertically mounted cylinders, internally heated, refractory-lined, and 10 inches ID. The range of carbonization temperatures was from 825° to 1,600° F. Using a regression-analysis computer program, empirical equations were developed by which carbonization temperature, air-to-coal ratio, devolatilization of coal, char yield, and volatile matter content of product char may be predicted.

Jan 1, 1973

By James L. Eirls

Tracor MBA under a contract to U.S. DOI Bureau of Mines designed, developed, fabricated and demonstrated a conveyor belt service machine. It is self-contained, battery powered, rubber tired and capable of handling, storing and transporting conveyor belting, wire rope and associated structures for sectional conveyor belts. While moving the tail section to its next position the machine discharges the belting, wire rope and belt structures. The belting is elevated and separated to provide for the insertion of the structures with minimum expended effort. A hydraulic system provides the power for steering, braking, winding or unwinding under controlled tension the belting and wire rope, operating a load-bed slat conveyor, raising, lowering and locking connection hitches and powering external hydraulic tools. Also, a pneumatic system is available to operate air impact tools. The service machine, with its present components can function in coal seams as thin as 48 inches, double wind conveyor belting 42 inches wide, 400 feet long, load or unload 3/4" wire rope on two separate reels and is controlled by two operators. A complete belt move using this machine requires only four workers. Successful underground demonstrations were conducted in coal mines located in West Virginia and Kentucky.

Jan 1, 1983

By Howard C. Turnage, Dana T. Updyke

An evaluation was made of one of several improved underground communication systems sponsored by the U.S. Bureau of Mines. The system evaluated was installed in a typical metal/non-metal room and pillar mine and utilized UHF repeaters connected to a unique distributed antenna and passive reflector system which provided mine-wide communications. A microprocessor controlled data collection system was assembled and installed for the evaluation. Data consisting principally of times and durations of messages and identities of the originating transceivers was collected between February and August of 1982 (6 mos.). Analysis of the data shows that the principal benefits are reduction in time required for unscheduled maintenance and repair, enhancement of safety, and better coordination of production activities. A cost benefit analysis shows a net benefit over cost, although it is also concluded that the capacity of the system is greater than can be justified by current activity in the mine.

Jan 2, 1983

By John R. Parker

Work places of an underground coal mine are required (30 CFR 1719) to be illuminated while self-propelled equipment is used. Permissible machine mounted systems have been developed and applied satisfactorily to many mining operations. However, some low seam and thin seam equipment has been difficult to illuminate because reliable, direct current systems and compact, low output, low glare luminaires were not available. This program resulted in the design and prototype construction of compact, low glare luminaires and AC and DC power systems, particularly suited to resolving illumination problems on low and thin seam mining equipment. Design objectives were based on enhancing the prospects for thin seam illumination solutions through definition of a product which could challenge markets enjoyed by higher glare luminaires and through reduction of technical risks associated with any new product development as well as the MSHA certification process.

Jan 1, 1982

By E. R. Palowitch

Two samples of the Lower Hartshorne (Spadra) bed were collected: A sample of the raw coal with the machine cuttings excluded, and a sample of the machine cuttings exclusively. Analysis of the 5-inch by 200-mesh size fraction of the raw coal, excluding machine cuttings, showed that a product meeting minimum quality specifications could be produced by washing at 1.60 specific gravity, yielding a theoretical 93.7 percent of clean coal. A negligible amount of near-gravity material at the separation gravity indicated an easy washing problem. The sample of machine cuttings had a maximum size of 2 inches and contained about 50 percent ash. Washability tests of the 2-inch by 200-mesh size fraction indicated that a theoretical yield of 30.0 percent of specification-grade coal could be achieved by washing at 1.49 specific gravity. As the machine cuttings represent an estimated 10 percent of the total coal mined, their inclusion in the mine output would increase the theoretical net yield of salable coal by only 3.7 percent. Because the machine cuttings contained a high percentage of sink 1.80 specific-gravity material, they had neither an effect on the separating gravity required to clean the raw coal nor on the difficulty of separation. Gabbing underground versus transporting the cut-tings to the surface for disposal or washing either separately or combined with the raw coal involves a number of practical, economic; and intangible factors; hence, no specific recommendations could be made. A discussion of some of the factors involved in dealing with a similar problem is given by Gandrud and Riley.4

Jan 1, 1962

By George S. Rice

"""To prevent the propagation of mine explosions, the Bureau of Mines, Department of Commerce, recommends rock-dusting all coal mines, except anthracite mines, in every part, whether in damp or dry condition. It also recom¬mends that rock-dust barriers be used to sectionalize the mine as additional defense; but these should not be regarded as a substitute for generalized rock-dusting."" (Mine safety decision, No. 5, April 7, 1927.)The purposes of this circular are to present concisely the requirements for effective rock-dusting of coal mines in order to prevent propagation of mine explosions, and to point out the principal related facts on explosibility of coal dusts and mixed coal-mine dusts, as determined by extensive testing in the Experimental Mine of the Bureau of Mines. study of these principal facts on coal-dust explosibility in conjunction with the recommendations for rock-dusting, should help to make clear to mine operators and others concerned the necessity for systematic rock-dusting in all coal mines except anthracite mines, and the futility of inadequate or sporadic rock dusting.The descriptions of nearly 1000 explosion tests in the Experimental Mine are available in a forth-coming bulletin2 and in earlier publications.3For detailed specifications as to the kind of rock-dust, amount to use, where to be applied, and method of sampling and testing, the reader is referred to Bureau of Mines Serial 26064, and American Engineering Standard Committee ""Recommended American Practice for Rock-Dusting Coal Mines"" quoted in Bureau of Mines Information Circular No. 60305.Summary of Specifications for Rock-Dusting1. Mines to be rock-dustedAll coal mines, except anthracite mines, should be rock-dusted.2. Extent of rock-dustingAll open accessible parts of a coal mine should be rock-dusted, including slopes, entries, cross,-cuts, and rooms, headings and pillar workings to within at least 50 feet of the face.3 Amount of rock-dustingAfter cleaning up the coal dust as thoroughly as practicable, sufficient rock-dust should be used to have the mixture of remaining coal-dust plus the rock-dust in any zone contain 65 per cent or more of inert or noncombustible matter. First dusting may require 3 pounds to 5 pounds per linear foot of passageway.4. When to rock-dust In any zone or section (made by dividing the mine for rock-dusting purposes) when the incombustible content falls to 55 per cent, that section should be re-rock-dusted so as to bring the incombustible content well above 65 per cent."

Jun 1, 1927

By Richard A. Walker

This report describes the development and performance of a multi-level, multi-function Calibration Light Source designed for field-calibration of a group of specific photometers. The Calibration Source is capable of providing ±35% accuracy calibrations at all of the following levels: 0. 05 foot-Lamberts, 6 foot-Lamberts, 6 foot-candles and 20 foot-candles. The Source was found to provide constant light output to within 1% over 50 hours of lamp operation and for line voltage variations of ±25%. It is compact and light-weight (11 pounds), and can be easily transported and used by one man in normal office environments (without requiring a darkroom).

Jan 1, 1976

By R. W. Watson

A belt-wearable self-contained self-rescuer (SCSR) manufactured by the CSE Corp. and designated the "SR-1OO" was evaluated for safety in the underground mine environment by the U.S. Bureau of Mines. The evaluation consisted of laboratory tests on the chemicals contained in the unit and field trials to simulate the mine environment. This report summarizes the test results and compares the results with those from earlier tests with chemical and compressed oxygen self-rescuers. It was concluded that the new SCSR did not pose any different or more severe hazards than the earlier units. In view of the mine-proven safety record of the SCSR's now in service, no reason could be found to disallow use of the belt-wearable unit.

Jan 1, 1991

By T. C. Green

A two-phase program evaluated commercial proximity warning devices and then served to design and develop an automatic electrostatic field strength measurement device with improved performance. The Phase I program consisted of test and evaluation of three commercial proximity warning devices, all of which operate on the principle of electrostatic field intensity measurement for determining proximity to high voltage power lines. Performance testing of these devices utilized full-scale cranes and power line systems and a scale model facility. The evaluation results were reported in the Phase I report entitled "Evaluation of Proximity Warning Devices" dated 22 February 1980. Under the Phase II program, a microproressor-based data acquisition system was designed and developed to collect and measure field strength at distributed points around the crane boom. This unit (referred to as the Distributed Sensor AC Electrometer) measures the field strength about a crane boom using 17 distributed sensors. Keyboard control is provided for the equipment operator. Measured field strength values are displayed on a line printer and recorded on magnetic tape. Laboratory testing of this unit demonstrated performance characteristics and field strength measurement accuracy within the design goals. A Phase III measurements program is proposed using the AC Electrometer to map the field strength contours about power line configurations.

Jan 1, 1981

By R. L. Rough

Photoelastic, wire resistance, and borehole-deformation gages were used to measure the in situ strains when an outcropping Black Hand Sandstone Formation in Hocking State Forest, Hocking County, Ohio, was overcored to stress-relieve the surrounding sandstone. Strains transmitted to the photo-elastic gage did not produce isochromatic patterns suitable for quantitative analysis. Strain readings from the wire resistance gage indicated tensile-strain loading during overcoring; readings from the strain-gage bridges in the borehole-deformation gage indicated compressive-strain relaxation during overcoring. The magnitude and orientation of the computed stress fields obtained from both gages were comparable when the corresponding tensile and compressive elastic moduli were applied. Stresses computed from deformation and resistance gages at depths to 5 feet showed the maximum stresses to range from 1.042 to 2.121 times greater than the minimum stresses. The bearings of principal stresses calculated from the deformation gage readings varied between N 61° E and N 83° E; the wire resistance strain gage bearing computations varied between N 68° E and N 82° E. Measurements of in situ strain in sandstone were shown to have promise but to require further development in field technique that could likely be achieved through experience.

Jan 1, 1971