Search Documents

By E. D. Gardner

The mine of the Eureka Standard Consolidated dining Co. is at Dividend, Utah, in the Tintic mining district. It is operated under the same management and controlled by the Antic Standard Mining Co.; the two properties adjoin each other. The Eureka Standard is worked through a vertical shaft; the ore is mined by a stringer-set-and-fill method. One hundred and thirty men were employed in April 1933. The normal daily tonnage is 100 tons; the ore is shipped to the smelter at Garfield, Utah.

Jan 1, 1935

By Henry P. Wheeler

Natural gas was first stored underground in Welland, County, Ontario Province, Canada, in 1915.3/ The following year natural gas in the United States was first stored underground successfully in the Zoar field near Buffalo, N, Y. Only three additional storage fields were in use in the United States in 1930, but by 1940 the number had increased to over 30, and since that time growth has been more rapid. At least 80 fields, with a combined storage capacity of 440,828 MM c. f ., were being utilized by 1949.4 / In May 1952, 142 storage projects having a capacity of 915,000 MM c.f. were in operation .5/ These fields are distributed from New York to California--from Michigan to Texas. In the Appalachian region alone, there are 101 storage fields with a combined capacity exceeding 526,000 MM cu. ft. Why Natural Gas is Stored Natural gas is stored in order to be readily available to meet the needs of consumers.

Jan 1, 1952

By E. A. Johnson

As part of its effort to reduce the environmental impact associated with mining and metallurgical operations, the Bureau of Mines used a modified form of the Environmental Protection Agency's Extraction Procedure toxicity test on copper reverberatory slags that contained low, medium, and high levels of the impurity elements As, Pb, Sb, Bi, and Zn. All tests resulted in extracts that did not exceed those limits published in the May 19, 1980, Federal Register; there-fore, these solid wastes were designated as nonhazardous for most landfill disposal situations. However, arsenic and lead levels disturbingly close to the allowable limits--and even higher levels of copper and zinc, for which there are no established limits--leached from the high-impurity-element granulated slags. These slags should be handled in such a way so as to minimize the possibility of water contamination. One baghouse dust was tested according to the EPA procedure and found to exceed the extract limits by a factor of 10. This solid waste may be considered hazardous.

Jan 1, 1982

By J. D. Ramsdell

The study described in this report was undertaken to obtain information on the character and effect of antimony additions to titanium. The availability of high-purity, low-hardness titanium metal, resulting from fused-salt electrorefining techniques, permitted a reassessment and evaluation of the physical behavior of titanium-antimony alloys. Alloys, based on several grades of titanium containing up to 10 percent antimony, were arc-melted and processed to sheet by hot and cold rolling. Properties and characteristics were evaluated by hardness tests, hot and cold rollability, annealing treatments, metallographic examination, and tensile tests.

Jan 1, 1960

By S. P. Signer

The Bureau of Mines conducted a series of field tests to improve the understanding of the support interaction mechanics between fully grouted bolts and coal mine roofs and to help lay the foundation for improved design and evaluation techniques. Strain gauges were installed on 14 fully grouted bolts placed in shale roof rock at four mines in Colorado, Illinois, and Pennsylvania to determine how load was transferred between the bolts and the rock. The results of field tests on elastic bolt behavior compared well with previous laboratory work and numerical models. The field tests showed that the anchorage length of grouted bolts installed in shale was slightly longer than the anchorage length determined in laboratory tests conducted in concrete blocks. The field results produced more variability because of geological variations. Tests run past the yield point of the steel bolt indicate that the yield zone varies significantly and translates down the length of the bolt anywhere from 4 to 22 in.

Jan 1, 1990

Analyze variably saturated flow in mining and other environmentally sensitive settings through the use of personal computer (PC) based software. The Problem There is an increasing need for mining companies to quantify water contaminants and their migration in the unsaturated zone. New and innovative computer models are therefore necessary to more accurately assess the potential impact of mining activities on groundwater resources and the environment. Applications for unsaturated flow modeling include (1) assessment of the impact of surface or underground extraction mining on flow conditions; (2) assessment of various hydrologic designs for resource recovery, such as in heap leaching or in situ leach mining; (3) assessment of the transport of conservative nonrcactive constituents in response to migration from spoil piles, or acid mine drainage; and (4) assessment of any combination of the above to facilitate expeditious permitting for mining operations. Since the mid 1970's there has been a proliferation of mathematical models and procedures for solving unsaturated now problems; however, few of these approaches have been integrated into software for public use. Commercially available unsaturated flow software models typically are limited to a single application and have restricted approaches. For example, computer codes that solve the unsaturated flow problem based on an analytic expression arc restricted to a simple geometric shape, homogeneous and isotropic materials, and provide only information regarding pressure and flow conditions in specified wells. The variably saturated computer codes that take advantage of the finite difference or finite element approach arc often restricted to either steady state or transient solutions; utilize one specific moisture-retention relationship and moisture-dependent permeability function; do not account for hysteresis; and are used with specific hardware such as a mainframe or work station. This restricts their use because they arc hard to interface, and arc often poorly documented, support dependent, and expensive. The mining community needs a flexible, more broadly based, variably saturated fluid flow simulator for the PC-platform to more accurately predict fluid movement in the mining environment.

Jan 1, 1991

By S. J. Pearce

One phase of the work of the Bureau of Mines in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory-protective devices. To insure that such devices will be available, the Bureau has established schedules of minimum requirements for self-contained breathing apparatus,3/ gas masks,4/ supplied-air respirators (hose masks, air-line respirators, and abrasive-blasting helmets, hoods, or masks),5/ dispersoid (dust, fume, and mist) respirators,6/ and nonemergency gas respirators (chemical-cartridge respirators).7/ Approval tests of self-contained breathing apparatus are conducted under the supervision of mining engineers of the Accident Prevention and Health Division} Region VIII; approval tests of other types of respiratory-protective devices are conducted by the Health Branch.

Jan 1, 1952

By A. W. Khair, M. Ahmad, Gehi. L. D.

"This paper presents an analysis of the effect of the dynamics of bit wear on dust generation. Two surveys have been conducted in order to assess the mechanism and type of bit wear and to evaluate the impact of bit wear on the productivity of the continuous miners. Used bits were collected from the underground coal mines and these used bits were utilized in laboratory coal cutting. The effect of bit wear on dust generation has been quantified and its impacted on dust generation and ventilation system has been exemplified.INTRODUCTION Research has reduced the prevalence of Coal Workers Pneumoconiosis from 15 to 5 percent according to NIOSH reports (Breslin 1982). However CWP still have not been eliminated as a hazard to mine workers. To prevent coal workers from having black lung MSHA has established a very strict standard for coal mine operations (2.0 mg/m3 with silica content equal to or less than 0.1 mg/m3,). There are numerous coal operations still experiencing great difficulty with meeting the 2mg/m3 dust standard. Among these are the longwall sections and continuous mining sections. In order to meet the rising demand of energy and coal, the number of longwall operations and continuous mining operations would have to be increased. Thus a long term research commitment is required to develop basic solutions that are more generic and greater benefit to the mining and mineral industry.In continuous-mining operations, the miners are exposed to the dust produced during the fragmentation of the coal from the face plus the dust produced during loading and transferring of the coal. The fragmentation process generates most of the respirable dust. The amount of dust generated during fragmentation depended on the coal properties, cutting parameters and cutting bit configuration. Bit wear changes bit configuration, therefore, it also affects dust generation. Bit wear can be defined as the removal of material from surface as a result of mechanical action. In soft coal mines bit wear may not be a serious problem but in hard coal seams bit wear is very significant. In addition, as the good coal seams are depleted, the operators are mining thin seams and the seams with rock partings. During cutting these seams operators are sometimes forced to cut roof and floor rock or rock partings which result in more rapid wear of bits."

Nov 1, 1995

By Irving Wender

This report describes Bureau of Mines experiments and reviews the work of others on the exposure of coal and coal-derived products to gamma rays and some other types of radiation. Results are presented on tests of three bituminous coals and a lignite that had been pulverized to minus 200-mesh particles and exposed to 1,000 megaroentgens of gamma irradiation from spent-fuel elements of a nuclear reactor. Of about 20 chemical and physical tests in Bureau work, only mass spectrometry of gases evolved during vacuum pyrolysis of the coals to 450° C gave results indicating differences in the irradiated and unirradiated samples. Mass-spectral distribution curves for CO and CO2 evolution showed fewer irregularities (reversals of curvature) for irradiated coals; thus, mass spectrometry appears to be the most sensitive method for determining radio-induced changes in coal. It is concluded that coal is not significantly altered by gamma irradiation owing to the resistivity of its highly condensed ring structure. High-level gamma irradiation, therefore, is unlikely to prove advantageous in coal processing and utilization. Specially treated coals, because of resistivity of coal to radiation damage, may be useful as an absorbent in processing radioactive wastes.

Jan 1, 1968

By Foster Fraas

This Bureau of Mines report describes a method for separating minerals at magnetic susceptibilities within the diamagnetic susceptibility range. The maximum feed rate varies directly with the square root of the lower limit of permissible susceptibility, while the lower limit of permissible susceptibility varies inversely as the square of the magnetic field strength. Minerals may be separated at particle sizes smaller than possible on conventional dry-type magnetic separators.

Jan 1, 1969

By P. L. Woolf

Three trials with oxygen-enriched unheated blast air are described. The trials were conducted in the Bureau of Mines experimental blast furnace located in Bruceton, PA. The first trial utilized moisture addition to the oxygenated blast. The second and third trial were conducted with natural gas injection. The test was basically a feasibility study and in that regard the practice was demonstrated to be feasible and also have possible advantages over hot blast operation. The testwork was conducted in 1964 and 1965 as part of a continuing study of iron making technology in cooperation with several North American Steel Companies.

Jan 1, 1985

The State of Washington has a federal program that gives the Office of Surface Mining responsibility for assuring the reclamation of lands affected by coal mining. Most of Washington's coal-bearing regions lie west of the Cascade Mountains. The state's coal reserves are estimated at 1.4 billion tons, about 0.3 percent of the nation's total coal reserve. Steeply dipping. minable seams range from 2.5 to 25 feet in thickness. The occurrence of coal in Washington has been documented since the early days of its settlement; at one time, coal production played a significant role in the state's economy. During the late 1800s and early 1900s, coal was second only to lumber in Washington's industrial production. Coal production declined as other sources of energy were developed. By 1959, production was at 200,000 tons. Regulation of the coal mine operations in Washington is conducted by the Office of Surface Mining's Casper, Wyoming, Field Office and its local office in Olympia, Washington. All permit applications and abandoned mine land reclamation are completed by the OSM Western Support Center in Denver, Colorado. Inspections of mine and reclamation sites are conducted by OSM reclamation specialists located in Olympia.

Jan 1, 1992

By John S. Dunning

This is one of a. series of papers being prepared for and published by the United States Bureau of Mines, describing raining and milling methods at crushed-stone plants throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized that publication of total production costs might in man; instances cause embarrassment to individual producers as well as to the industry as a whole. However, operating costs are essential to technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that the scope of the cost tabulations shall not be misunderstood. This paper deals with the quarrying and crushing methods used at the Avon Mountain trap-rock quarry of the Atlas Sand, Gravel & Stone Co., in West Hartford, Conn.

Jan 1, 1936

By R. W. Fatzinger

The accident-frequency rate for placer mining in 1942 is reported as 36.923 accidents per million man-hours worked. This figure places placer-mining accident frequency slightly higher than that given for quarrying-35.7-but considerably under the 78.0 for coal mining and 56.5 for metal mining.4 Placer mining is subdivided into four types of activity: Underground, surface, dredging, and hydraulicking. It is the purpose of this paper to present and discuss safety practices in dredging and hydraulic mining; therefore, the following considerations will be limited to these two types of placer mining.

Jan 1, 1948

By E. C. Lane

During the past 15 years the Bureau of Mines has made and published several hundred analyses of typical petroleums and has developed a system of interpreting the analyses and of classifying crude oils. In describing crude petroleum frequent reference is made to the "base" of the oil, a usage the petroleum industry has found convenient. As part of its general study of the characteristics of crude oils, therefore, the Bureau of Mines has developed a system of classifying them according to "base." This system as first published in 1927 was limited to four classes and in its original form is no longer considered adequate. Since the system was first published the Bureau has analyzed a large number of crude oil, including representative samples from nearly every important producing field in the world, and has found that the system of classification could be revised and amplified to advantage. The revised system is presented herein.

Jan 1, 1935

By Gary P. Sames

This report discusses some practical applications of a geotechnical investigation conducted by the U.S. Bureau of Mines that can help mine operators meet revised Federal regulations in their roof control plans. The investigation, designed to characterize roof conditions near the coalbed outcrop in drift coal mines in eastern Kentucky, revealed that weathered stress-relief joints near outcrop are crucial ground control factors in the region. The joints' origin and character were determined through underground mapping of many joints in coal mine roof and detailed observations and measurement of joint trends and physical characteristics in widely separated strip mine highwalls and roadcuts. This resulted in an understanding of stress-relief-joint patterns and the effect of various rock types on the intensity of weathering in the joints. That information is used in this report to show how stress-relief joints contribute to roof failure and how, through improved roof support and mine planning, safer roof support plans can be developed.

Jan 1, 1992

By Edward E. Johnson

The U.S. economy boomed in 1965, completing its fifth consecutive year of expansion. Although the advance was somewhat irregular, previous records for production, sales, employment, and income were topped. During the first few months of 1965, as the economy recovered from the depressing effects of the automobile strikes of late 1964, increases were unusually large. The gains moderated in early spring, but were stimulated at midyear by sharply rising capital outlays, excise tax cuts, in? creased Social Security payments, and accelerated Viet-Nam defense expenditures. Gross national product (GNP) in cur-rent dollars rose $49.5 billion or 7.8 percent, to a total of S681.2 billion. In constant dollars (effects of price changes eliminated), GNP increased 5.9 percent, a rate considerably higher than the historical postwar annual average growth of 3.5 per-cent. Demand increased in most final markets and was especially strong for business fixed investment and consumption expenditures. With the exception of construction, most of the increases in GNP were real, since prices increased less than 2 percent.

Jan 1, 1966

By Wilbert J. Huff, Raymond H. Moore

"Black powder is employed widely in peace and war. Its properties are therefore of considerable interest to many. The Bureau of Mines frequently is asked to furnish information on its use and safe handling in the mining and mineral industries in times of peace and is now engaged in studies of its application to the arts of war.Black powder has been the agent in many accidents - some very disastrous - and its handling and use are deemed very hazardous. The belief is widespread that the hazards are due principally to the ease with which the powder is ignited by a hot spark or flame in contradistinction to high explosives; these usually are ignited only with difficulty, and some burn incompl0tely and to a certain extent are self-extinguishing. Primary precautions, .therefore, should be taken to prevent the access of heat, spark, and flame.In black powder manufacturing operations a frequent source of disaster is the initiation of fires and explosions in the wheel mills in which the sulfur, charcoal, and nitrate are incorporated. Long experience has indicated that the wheel mill probably will fire if the powder is not kept moist enough; manufacturing supervision calls for the maintenance of a minimum moisture content, at least during the milling. Accidents occur elsewhere in the manufacturing line, and in an endeavor to minimize these, particularly those happening in corning mills, one of the writers suggested many years ago that a suitable humidity be maintained in other operations in the hope that it would serve protectively as in the wheel mill. The experience of one company for many years with this practice was favorable. It seemed desirable therefore, to explore the question experimentally."

Nov 1, 1944

By Dennis R. Dolinar

Physical property tests were conducted on drill core from three exploratory holes on the Naval Oil Shale Reserve near Anvil Points, Colo. Data and regression analysis curves are presented. Data obtained above the Mahogany zone were used to estimate the potential zone of surface effects from under-ground mining. Single specimen testing was primarily used to obtain Mohr's envelope and subsequent rock properties. The technique is shown to provide satisfactory results for this rock type with a significant reduction of core preparation and testing time.

Jan 1, 1981

By J. Walden, S. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers mounted in suspension components can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information horn a Global Positioning System is recorded at the same time as shock pressures or acceleration data, then the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck.