Search Documents

By T. L. Joseph

The size and accessibility of the Minnesota manganiferous iron ore deposits make them attractive as a potential source of ferromanganese, which is essential in the production of steel. For several years the Bureau of Mines has been conducting experiments to determine the feasibility of producing ferromanganese from these ores by a three-step process which involves (1) the smelting of the ores in the blast furnace to produce a high-phosphorus spiegel; (2) the treatment of the spiegel produced from step 1 in an electric or open-hearth furnace to separate the manganese from the phosphorus and the iron; and 3) the smelting of the high-manganese slag from step 2 to produce ferromanganese. The details of the first two steps of the process and the results of tests with the experimental furnaces have been given in previous reports.

Jan 1, 1931

By S. H. Lorain

The Minah silver-lead mine in the Wickes district, Jefferson County, Mont., produced substantial quantities of silver-lead ores in the 1890's. The mine has been abandoned since the "silver panic" of the early 1900's. As a part of the Bureau of Mines: program to develop new sources of lead to overcome the growing shortages of that metal, a development project was started at the Minh mine in April 1946 and continued until June 1947, during which 5,600 feet of angledozer trenching and. 1,093 feet of core drilling were completed on the main vein and nearby parallel veins: As a result of this work, interest in the property was stimulated and private operators are now engaged in reopening the mine. This report discusses the past history, geologic setting, and the recent and early operations of the mine.

Jan 1, 1948

By Lars Skogsberg

Work with hand-held power tools can be found in most industries all over the world. This type of work exposes the operators to different kind of loads like gripping-forces, feed-forces, exposure to vibration and noise, holding hot or cold surfaces and the exposure to dust. Designing a power tool with good ergonomics is a matter of finding the best compromise. As a simple example, increasing the mass is not acceptable because it will increase the forces needed to handle the tool. At the same time increased mass will in most cases reduce the vibrations. Vibration disorders related to the use of hand-held power tools has been known and reported since long. It is therefore essential that low vibrating tools are developed and used. The new vibration regulations in Europe, based on the Physical Agents (Vibration) Directive, have put increased focus on the vibration control in industry. Forces acting on the tool cause vibration Tools for industrial use must be of very robust design to withstand the very hard use they are exposed to. Industrial tools are therefore normally designed with the main parts made of metal. From a vibration point of view this means that most tools can be regarded as rigid bodies, especially because the dominating frequency normally is equal to the rotational frequency of the tool spindle or the blow frequency for a percussive tool. These frequencies are with few exceptions below 200 Hz. Handles however can not always be regarded as rigidly connected to the tool. There are several examples of weak suspensions designed to reduce vibration transmitted to the hands of the operator. There are also examples of designs where the handles just happened to be non-rigidly connected and in some cases even in resonance within the frequency region of interest. Oscillating forces act on the tool and the result is vibration. Design principals In all cases forces are the source of vibration. This leads to the three basic principles to control vibration: • Control the magnitude of the vibrating forces. Examples are the balancing unit on a grinder or the differential piston in a chipping hammer. • Make the tool less sensitive to the vibrating forces. Examples can be when the mass of the guard on a grinder is rigidly connected to the tool to increase the inertia of the tool. • Isolate the vibrations in the tool from the grip surfaces. Examples are vibration-dampening handles on grinders or pavement breakers, the air-spring behind the blow-mechanism in a riveting hammer or the mass spring system in a chipping hammer.

Jan 6, 2006

By K. L. Rubow

"Diesel exhaust and mineral dust concentrations have been measured for aerosols generated in the laboratory and as found in five underground coal mines- 3 utiliting diesel-powered hallage equipment and two electric-powered equipment. Two source apportionment techniques have been applied to differentiate between the mineral dust and diesel exhaust aerosol concentrations. The first technique, using a microbrifke uniform deposit impactor CMOUDI) for size selective sampling, is based on modeling aerosol size and the premise that the diesel exhaust portion of .the aerosol is predom1nately submicrometer and the mineral dust portion is mostly greater that one micrometer in size. The second technique, Chemical Mass Balance CCMB) modeling, was used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results. ,The MOUDI size distribution data were modeled to obtain parameters describing the fine and course fractions of the sampled aerosol and to estimate the contributions to each mode from both mineral ·dust and diesel exhaust aerosol sources. The results showed the size distribution of the mixed aerosols exhibited two definite modes with the minimum between the modes occurring at 0.8 um. For the diesel equipped mines, this analysts yielded an average value for the fraction of the fine aerosol attributable to mineral dust of 1 pct. Less than 5 pct of the coal mine diesel aerosol was found in the coarse size fraction. CMB analysis confirms the original premise for using aerosol size to separate diesel exhaust and mineral dust aerosol during sampling."

Jan 1, 1988

By V. Castranova, T-M. Ong, V. Vallyathan, M. J. Keane, W. E. Wallace Jr.

"Inhalation of certain forms of silica, asbestos and some other respirable dusts can result in pulmonary fibrosis, characterized by destruction of the surfaces of alveoli and respiratory bronchioles. Fibrous thickening of the alveolar septa decreases the lung's capacity for gas exchange.Pulmonary macrophage damage by respired dust may initiate the fibrotic response.In one proposed mechanism, dust particles interact with the plasma membrane of a macrophage. This damages the cell or induces some hyperactivity of the cell, resulting in excessive release of lysosomal enzymes and reactive forms of oxygen (1). These reactive enzymes or radicals then damage the alveolar surface epithelial cells. A second mechanism has also been pro¬posed (2,3) in which dust damage to the macrophage causes the release of mediator substances which induce pulmonary fibroblast cell proliferation and increased collagen synthesis. This produces fibrous tissue in the terminal air spaces (4,5).Mineral surface interactions with plasma membrane lipoproteins have been proposed as a mechanism of lytic damage of pulmonary cells by silica dust in numerous models (6,7). The significance of dust surface proper¬ties has been further revealed in studies showing significant changes in dust induced cytotoxicity as a function of dust surface crystallinity and organic or inorganic contamination or coating of mineral surfaces (8,9). Such modification of the mineral surface might interfere with surface sites responsible for the toxicity of dusts for pulmonary macrophages, thus interrupting the early stages of the process of fibrosis.In vitro cellular assay systems using erythrocyte hemolysis or the release of macrophage cytosolic or lysosomal enzymes following dust challenge, have been used to analyze the initial mechanism of dust damage to cells. However the ability of these assays to predict the pulmonary disease producing potential of various dusts is imperfect owing to some ""false positive"" results. These assays as performed are therefore questionable models for the initial lesion in pneumoconiosis or silicosis. In particular, kaolin frequently is found to have comparable biological activity to silica quartz in these assays (10,11).Silica and kaolin have distinctly different fibrogenic potentials. Silica is highly fibrogenic, resulting in both acute and chronic silicosis (12). Some epidemiological data and animal experimentation data have indicated that long term exposure to kaolin can result in pneumoconiosis; however, kaolin is relatively benign as compared to silica (13-18). Kaolin is also of interest because it is one of the major mineral inclusions in Eastern U.S. bituminous coals. We have observed that exposing respirable sized native silica or kaolin for two hours to pulmonary macrophages results in a greater enzyme release for kaolin exposures, on a dust mass basis. Exposure of erythrocytes to the dusts also results in greater levels of hemolysis by kaolin for equal mass respirable dust doses. Therefore, these results do not correlate positively with known disease inducing potentials of the two dusts.Characterization of physical and chemical surface properties of dusts involved in occupational exposures, and characterization of the alteration of those surface properties which are likely to occur upon deposition of the dust in the lung, should improve the identification of respiratory disease hazards.Inhaled dust particles deposited in the lower respiratory tract will come in contact with pulmonary surfactant. This surfactant forms a surface film on and emulsion in the liquid hypophase coating of the alveoli and respiratory bronchioles. The primary constituent of this pulmonary surfactant is the lipid diacyl glycerophosphorylcholine, lecithin (19). Because this lipid is also a major component of cell membranes, it is possible that surfactant can interact with mineral dust to alter its Interaction with macrophages and other pulmonary cells and, thus, it"

Jan 1, 1988

Develop a means for analyzing seismic crosshole data to predict and monitor the Flow of leach solution during in situ mining. Background Improvements in predicting and monitoring in situ leach solution flow would aid in planning well field configurations. These improvements would also facilitate permit application by assuring regulatory agencies that leach solution would not escape from a well field undetected. Seismic tomography can detect fractured zones, which enables the prediction of probable flow paths, and it is a promising technique for monitoring leach solution injected above the water table. Tomographic analysis of crosshole seismic data provides a two-dimensional picture of the distribution of seismic velocities between the transmitter and receiver boreholes. The positions of fractured zones and of leach solution can then be inferred from the seismic velocities.

Jan 1, 1989

By Harry Vivian

This paper deals principally with the retreating method of mining as applied in the Calumet & Hecla Consolidated Copper Co.'s deep Conglomerate mine, pointing cut some of the difficulties encountered in deep mining and describing the particular methods used at Calumet to carry on a large-scale operation at great depth with a minimum hazard factor. The circular is one of a series dealing with mining methods and costs which is being prepared for and published by the United States Bureau of Mines. ACKNOWLEDGMENTS Acknowledgment is due to those officials and operating heads of the Calumet & Hecla Cc. whose years of familiarity with the conditions developing at the Conglomerate mine as great depth was attained have enabled them to contribute valuable information to the subject of deep-mining problems.

Jan 1, 1931

By John A. Kost

Control of the dust produced by continuous mining machines in coal mines is conventionally attained by water sprays from fixed nozzles mounted on the frame of the machine behind the cutting head. In the tests conducted under this contract a so-called "wet-head" machine was used, where the spray nozzles were mounted on the rotating head itself, close to the coal-cutting bits. The tests were conducted at the Robena Mine of U.S. Steel Corporation, using Lee-Norse machines. Operating the wet-head machine and a conventional spray machine in turns in the same section, it was found that the wet-head produced approximately 25 percent less respirable dust and 60 percent less total airborne dust than the conventional spray machine. The wet-head also greatly improved the visibility of the cutting bits from the machine operator's position. Several difficulties had to be overcome before any meaningful tests could be conducted, including excessive pressure drops in the piping system and plugging of the nozzles from internal water contamination. The major obstacle, however, was the rotating water seals on the wet-head, which leaked excessively after only a few hours of operation. Only after several changes and plant and laboratory tests was a design found which permitted conducting the underground tests without appreciable water leakage.

Jan 1, 1976

By J. M. Stuve

The present Bureau of Mines investigation measured low-temperature heat capacities of NiBr2 (8 to 302 K) and NiS04 (9 to 70 K) by adiabatic calorimetry. The standard entropies (S°, 298.15 K) of NiBr2 and NiS04 were calculated as 29.26 ± 0.06 cal/deg mole and 24.21 0.04 cal/deg mole, respectively. (1 cal = 4.1840 joules.) Heat-of-solution measurements of anhydrous NiBr2 were used to determine its enthalpy of formation (?Hf°, 298.15 K) as -50.64 ± 0.31 kcal/mole. High-temperature enthalpies of NiBr2 and NiS04 were measured by drop calorimetry to 1,150 K and 1,002 K, respectively. Enthalpies, heat capacities, and related formation functions are tabulated to 1,200 K.

Jan 1, 1978

By Alfred E. Schwaneke

The surface tension from 240° to 844° C and the density from 236° to 583° C of 99.999 percent purity liquid tin has been measured using the maximum-bubble-pressure method. Results for surface tension (y) show y (dynes/em) = 566.84 -4.76 X 10-2 T (° C) with a standard error of 1.9 dynes/cm. Results for density (p) show p (g/cm3) = 7.16 -6.3 X 10-4 T (° C) with a standard error of 0.012 g/cm3. Comparisons with other data found in the literature are discussed. The experimental results are considered to be as good as any data presently available.

Jan 1, 1970

By Wing G. Agnew, John A. Johnson, McHenry Mosier

"INTRODUCTION AND CONCLUSIONSThe first three reports of investigations 5/ in this series, pertaining to the investigation of stemming at the Mount Weather Testing Adit dealt with the dust produced by blasting, the effect of stemming on gases generated by blasting, and the relative advantages and disadvantages of different types of stemming and no stemming when used with 60-percent ammonia gelatin dynamite.This report covers an investigation of the length of stemming material through which a primer will fire and detonate a charge of dynamite, such as a missed hole.The practice of drilling a new hole a foot from a missed hole to blast out the missed hole should be prohibited. It is dangerous, as is evidenced by the number of miners killed through drilling into missed holes. It is even more hazardous in a mine on a multiple-shift basis, in which the same miners do not drill succeeding rounds."

May 1, 1942

By Oliver Bowles

From the most remote periods of civilization stone has been used to perpetuate the memory of individuals or to immortalize their noble achievements. Ancient memorials ranged from simple piles of stone (cairns), or single markers, to great obelisks and pyramids or magnificent mausoleums. The Taj Mahal at Agra, India, built of white marble by Shah Jehan in memory of the Empress Mumtaz Mahal, is one of the most beautiful and costly memorials ever built. It was erected between 1632 and 1650 at an estimated cost of $50,000,000 or more and is today an object of unusual interest for travelers. Other magnificent memorials both ancient and modern are to be found in many lands. No sharp line can be drawn between buildings and monuments, because the larger types of memorials such as the Bok Singing Tower, Lincoln and Jefferson Memorials, and mausoleums of various types have features in common with buildings. However, great care must be exercised in selecting a site for a quarry that will produce acceptable monumental stone because appearance as well as quality is of prime importance. The deposit must be of uniform texture and attractive color and must be notably free of knots, hairlines, impurities, incipient seams, or other defects. Many memorials are of polished stone, and spots or streaks that might be virtually Invisible on a natural rock face will appear distinctly on a polished surface. Hence, stone to be polished must be selected with unusual care. However, less flawless stone may be used for hammered surfaces.

Jan 1, 1955

By J. P. Morris

The Bureau of Mines investigated the mechanics of fuming of iron-carbon melts during top-blowing with oxygen. Melts weighing 45 lb were prepared in an induction furnace and blown with oxygen by means of water-cooled lances. The rate of fuming was measured and correlated with the operating variables. The data showed that the primary cause of fuming was a boil at the bath surface in the impingement zone of the oxygen jet. Nucleation of the carbon monoxide bubbles producing the boil was apparently brought about by the precipitation of an oxide phase. The actual fuming mechanism involved partial oxidation and vaporization of bubble films and fine metal spray generated by the bursting of the bubbles. Bubbles that formed outside the impingement zone produced little fume. The distribution of trace elements between the metal and fume strongly indicated that the fume contained fine spray particles as well as particles that had condensed from vapor. The rate of fuming was found to be proportional to the carbon content of the metal) the concentration of oxygen in the jet) and the bath temperature) provided that a continuous boil occurred. In the absence of a boil) very little fume was produced.

Jan 1, 1967

By D. E. Traut

A fluidized, countercurrent ion-exchange system was developed, operated, and evaluated by the Bureau of Mines in support of its objective to help assure an adequate uranium supply for future national needs. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows are continuous, except for short periods when resin increments are withdrawn. The exchange of uranyl sulfate between a simulated acid-leach-uranium solution and a strong-base, ion-exchange resin was studied, together with subsequent elution using an acidified sodium chloride solution. The effects of the number of compartments, compartment height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. Also examined were the kinetic and equilibrium relationships for the absorption and elution steps. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The columns system was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By Thomas M. Barczak

Wood cribs are used extensively to stabilize openings in underground coal mines. This U.S. Bureau of Mines report describes the results of full-scale testing of several multitimbered wood crib configurations. Multitimbered configurations are wood cribs that are constructed with two or more timbers per layer. Nine different crib configurations were evaluated. Configuration parameters under study included the aspect ratio (height-to-width relationship) and the percentage of solid rr:aterial used in crib construction. Test results and generalized wood crib behavior are discussed and recommendations are made concerning crib constructions to maximize strength and stability. Crib performance is enhanced by reducing buckling effects by decreasing the aspect ratio and geometry considerations that increase the moment of inertia. A cost benefit analysis of multitimbered wood crib configurations is made. Generally, increasing the percentage of solid provides more resistance at less unit construction cost. A comparison of laboratory results and underground observations of several wood pack wall supports suggest in situ load capacity is less than that measured in laboratory testing. Reasons for the apparent decrease of in situ load-bearing capability include load rate effects, stiffness of reaction surfaces, and varying boundary conditions that alter the load transfer mechanics of the crib structure.

Jan 1, 1991

Through a contract, the Bureau of Mines has funded the development of an Automated Breathing Metabolic Simulator (ABMS). The ABMS simulates man in all of the breathing and metabolic parameters for monitoring support and resuscitation equipment. For the first time, complete breathing and metabolic simulation are incorporated in the same device. Breathing rate, breathing depth, breath velocity contour, oxygen uptake, and carbon dioxide release are all variable over wide ranges, simulating conditions from sleep to hard work with respiratory exchange ratios covering the range of hypoventilation to hyperventilation. In addition, all of these parameters are remotely controlled to facilitate the use of the device in hostile test environments. The exhaled breath is also at body temperature and completely saturated. The simulation in faith¬ful to the extent of having a variable functional residual capacity and an anatomical dead space equivalent to that of humans. The ABMS will be used as a stand-in for humans in test and validation of respiratory equipment, permitting more extensive and safer evaluation in hazardous environments where human testing would have to be limited. In addition, it will greatly reduce the cost of prolonged testing in cases where simulation chambers with human subjects require three shifts of crews, including standby physicians. Perhaps most importantly, it will provide a calculated and reproducible test and validation facility. The ABMS is under complete computer control. Through a typewriter terminal the test sequence can be input into the computer which will then automatically adjust the ABMS to simulate any desired sequence of metabolic activities for time durations up to 15 hours. The computer also monitors the test procedures and provides test results printout.

Jan 1, 1973

By W. A. Heitbrink, M. Schmitz, J. A. Organiscak, A. B. Cecala, E. Ahrenholtz

Operator cabs on a front-end loader and a rotary rock drill were retrofitted with ceiling mounted heating1AC units and air filtration systems. Subsequently surface coal mine field studies were conducted to evaluate the respirable dust protection these retrofitted cab systems offer to the equipment operator. A significant 10: 1 respirable dust protection factor (ratio of outside to inside cab dust levels) was measured for the front-end loader cab with positive pressurization of the cab interior. Whereas an insignificant 3: 1 respirable dust protection factor was measured for the drill cab without positive pressurization of the cab interior. These results indicate that achieving positive interior cab pressurization with retrofitted cab filtration systems is a key element to their dust control effectiveness.

By Bernard Porter

The rate of the heterogeneous reaction between reactor-grade yttrium and lithium fluoride in lithium fluoride-yttrium fluoride mixtures was measured using a quartz spring balance. At 950° C the magnitude of the rate of reaction is 10-5 grams of yttrium/cm2-sec. The heat of activation for the reaction is 38.3 kilocalories per mole of LiF. A surface-controlled mechanism is proposed in which LiF is adsorbed on the yttrium metal surface. An activated complex is formed when additional LiF reacts with the adsorbed LiF-metal site. The activated complex then decomposes to the products) which are lithium metal and YF3. The importance of the reaction in the electrowinning of yttrium metal from fluoride electrolytes is discussed.

Jan 1, 1967

By Oliver C. Ralston

The Nonmetallic Minerals Division of the Bureau of Mines deals with all mineral substances not intended to be used as ores for extraction of metals, with the exception of the fuels. However, coal washing, the methods of which are highly Similar to the concentrating methods for ores, is in¬cluded In the work of the Nonmetallic Minerals Division to facilitate administration and to avoid duplication of equipment. During the fiscal year most of the work of the division was done at the experiment stations in College Park, Md., Tuscaloosa, Ala., and Seattle, Wash.

Jan 1, 1938

By E. Morrice

This report of the Federal Bureau of Mines presents a laboratory procedure, with the requisite equipment, for electrowinning ingot (liquid) cerium metal from a fused-fluoride bath, the metal purity being about 99.9 percent. Physicochemical studies, including bath properties and electrochemistry, are included, with a speculative model of the mechanisms involved. An historical review of the methods used for electrowinning misch metals and yttrim-group metals, as well as individual rare-earth metals, is presented. The electrolytic preparation of metal from fused salt and nonaqueous media is summarized, along with the unsuccessful attempts at depositing the metals from aqueous solutions.

Jan 1, 1961