Search Documents

By Gary Choate

The work presented in this report represents the background activity which led to the fabrication and testing of a greenhorn and crowd limit switch system for electric shovels. The program began With a literature search and manufacturers product review to gather material as a basis for concept generation. Visits to three open pit mines provided information from operation and maintenance managers which was useful in preparing design concepts. These concepts were evaluated through laboratory tests and engineering analysis to select a final design concept. The resultant greenhorn is four separate shock absorbing pads each enclosed in a housing which bolts to the end of a dipper handle adaptor. The plungers impact against stops mounted to the saddle block. The crowd limit control is a nonmechanical device which senses the location of the dipper and makes appropriate commands to the crowd motor to insure against impacting the greenhorns. The electronic crowd limit control is redundant and indicates malfunction modes. The greenhorn prevents shovel damage in the unlikely event of impact.

Jan 1, 1983

By N. Barton

Large scale tests were conducted on quartzitic gravel and crushed sand-stone to investigate pertinent geotechnical properties for backfill support of egress shafts. Such shafts are envisaged for rapid launching of deep-based missiles. The backfill support is designed to resist shaft closure under dynamic loading, and must also drain rapidly to a lower catch chamber to allow launching. Large scale tilt shear tests were performed to measure the internal shear strength of the two backfill materials. Shaft filling and emptying tests were conducted in a 12 ft deep, 3 ft diameter model section of shaft drilled in sandstone. One half of the model was smooth bored, the other half rough-surfaced to represent drill and blast surfaces. Vertical and horizontal pressure cells indicated that stress only built-up during the first 1 to 1 ½ diameters of filling, due to the high-sidewall friction of 38° for the rough shaft and 31° for the smooth shaft. Interface sliding tests were performed to confirm these figures. Static and dynamic deformation tests were also per-formed, and indicated moduli as high as 56,000 psi, which will give excellent shaft support. Both the shaft support characteristics and the ease of emptying of gravel look particularly promising.

Jan 1, 1983

By C. E. Brechtel

This project describes the design and testing of large face ventilation systems for oil shale mining. A design data base was generated by reviewing general industry practice, oil shale industry planning, and technical literature. Conceptual designs for seven different systems were developed and evaluated for suitability. A large, free-standing, jet fan and reversible fan with rigid duct were selected for fabrication and testing. The two systems were field tested in a dead-end heading 55 ft wide by 30 ft high and 320 ft long. System performance was optimized using measurements of air flow direction and air velocity. Total system performance was then measured using SF6 tracer gas released to simulate blast fumes, hot diesel exhaust, methane layering and methane from a blasted muckpile. Field testing indicated that both systems delivered similar performance. The jet fan offered some clear advantages because of its mobility, ease of oper-ation and lower power requirement. It also offered some functional advantages in ventilating for methane because of it high average velocity.

Jan 1, 1985

By William M. Schafer

Forage plots were established on agricultural lands contaminated by acid mining waste. The acid produced through oxidation of pyrite and other sulfides caused elevated solubility and plant availability of copper, zinc, and arsenic which killed vegetation and polluted surface and groundwater. Soil amendments including agricultural lime (CaCO3), hydrated lime (Ca(OH)2), phosphorus, and organic matter were used to reduce the toxicity of metals. Several acid-tolerant grasses were used to vegetate the amended soils. Various soil extraction techniques were used to see which best correlated with vegetation performance. The extractions corresponded to three "forms" of metals in soil including soluble (water-saturation extract); plant-available/weakly adsorbed (DTPA extract); and total (HNO3/H202 extract). Of the extractants tested the DTPA levels appeared to correlate best with metal levels in plant tissue. The DTPA soil extractant serves as a useful tool in predicting potential phytotoxicity of mine waste materials.

Jan 1, 1989

By Jaffrey Y. Foley

Placer gold and platinum-group metals (PGM) In the Slate Creek area, northern Chistochina Mining District, are derived from silicified and carbonate-altered, Cretaceous-Tertiary (?) dikes and related mafic and ultramafic rocks. Gold In the placer deposits is also derived from Tertiary conglomerate and altered Jurassic-Cretaceous argilllte. The argilllte and Igneous bedrock sources show a unique Ag-Au-Cu-Hg-PGM association that Is attributed to a combination of magmatic, hydrothermal, and supergene processes. The bedrock and placer deposits contain a variety of gold silver-lead-copper and PGM alloys. The observed geochemical, mineralogic, and alteration features are consistent with current geological models for turbidite-hosted gold deposits. No economic gold or PGM lodes were Identified, but several areas warranting more detailed investigation were Identified. Conventional geochemical sampling and analysis of small sample splits weighing between 10 and 30 grams were shown to be unreliable as a consistent means of identifying gold- and PGM-bearing bedrock. Pan concentration of pulverized rock samples was shown to be a more effective, but still Imperfect means of Identifying gold and PGM source rocks. Geochemical data and mineralogic examination indicate that gold and PGM in potential lode sources are very finely and erratically disseminated, are chemically combined with other elements, and may not be entirely free-milling or amenable to simple gravity concentration.

Jan 1, 1990

By J. Owens

Advanced materials development ranks as one of the most important high-tech industries of the future in the United States. Recent breakthroughs can be attributed to advanced computer technology, powerful mathematical models, and more precise analytical tools that enable scientists to examine and control properties of materials as never before. Discoveries now being made are providing many industries with opportunities to improve product lines, fabrication techniques, product reliability, and so forth. More¬over, industries, such as space, medicine, and defense, which require stringent: design and perfomance specifications in highly competitive world markets, increasingly demand these new materials. The definition of advanced materials used here is one that has been adopted by the U. S. Bureau of Mines: Those materials which have been developed over the past 30 years or so, and which are being developed at present, that exhibit greater strength, higher strength-density ratios, greater hardness, and/or one or more superior thermal, electrical, optical, or chemical properties, when compared with traditional materials.

Jan 1, 1991

As part of remote sensing research on an abandoned mine lands (AML) site in the Colorado Springs, Colorado area, a geographic information system (GIS) database was generated. This GIS database contains information on the locations and extents of abandoned underground coal mines, the geology of the area, subsidence features and degrees of subsidence risk, topography, drill hole locations, and lineaments (linear features) related to subsurface geologic structures. A GIS database allows the reproducible and accurate comparison and analysis of any data sets which geographically overlap and are within the same coordinate system. The database has been released to the public domain so that government agencies, researchers, educators, and the general public can access this coherent database for the purposes of better understanding the study area and GIS technology. Data files and maps are available in formats that are compatible with the GIS software used in the research project and with most CAD systems so that as many people as possible can make use of the majority of the database. This document serves as the data dictionary for the database by providing descriptions and origins of the data files.

Jan 1, 1992

By C. W. Morris

This Final Report describes the major technical activities that were accomplished to produce a comprehensive continuous miner training system (CMTS) for coal industry utilization. The primary product of this program was a continuous miner part-task trainer. It is composed of an interactive computer graphics system combined with the operating controls of a continuous mining machine mounted in a simulated cab. The cab contains an audio system for reproducing continuous miner operational sounds. The trainer is supplemented with a complete set of cognitive materials that provide instruction in the operation, safety and health of continuous miner operations. A complete summary of the field test and evaluation of the CMTS is provided along with a set of recommendations for further training program refinements, expansions, and utilization.

Jan 1, 1982

By C. W. Morris

The continuous miner training system provides classroom materials training aids, and a continuous miner simulator to provide a short, intensive instruction and skills development program for training or retraining continuous miner operators. This project included refinement of training objectives, revision of training aids, improvements to the simulator, and evaluation of the entire system. This report describes the revised classroom materials and the validation of the training system.

Jan 1, 1982

By Donald J. Keefe

The Remote Working Level Monitor (RWLM) is an instrument used to remotely monitor the Rn-daughter concentrations and the Working Level (WL). It is an ac powered, microprocessor based instrument which multiplexes two independent detector units to a single central processor unit (CPU). The CPU controls the actuation of the detector units and processes and outputs the data received from these remote detector units. The remote detector units are fully automated and require no manual operation once they are set up. They detect and separate the alpha emitters of RaA and RaC' as well as detecting the beta emitters of RaB and RaC. The resultant pulses from these detected radioisotope; are transmitted to the CPU for processing. The programmed microprocessor performs the mathematical manipulations necessary to output accurate Rn-daughter concentrations and the WL. A special subroutine within the program enables the RWLM to run and output a calibration procedure on command. The data resulting from this request can then be processed in a separate program on most computers capable of BASIC programming. The calibration program results in the derivation of coefficients and beta efficiencies which provides calibrated coefficients and beta efficiencies.

Jan 1, 1977

By Robert E. Green

This Final Report summarizes the results of work accomplished under Contract No. J0215039. It is in an executive overview or executive summary format. The number and description of the various technical reports prepared and submitted is outlined. The essential changes and reasons for the revised program schedule/contract modifications actually enacted in May 1982 are discussed in detail. The evolving mines/deposits list and the accompanying criteria classifications are explained along with the verifications/justifications for adding or deleting specific mines/deposits to the list. Difficulties and problems experienced during the different phases of the project in conjunction with the ensuing remedies are highlighted. The final section of they report is devoted to presenting Davy McKee's suggestions for improvements to future MAS commodity studies. Appendix I is comprised of three of the evolving mines/deposits lists starting with the original RFP list and ending with the final completed list. Appendices II and Ill are tabulated summaries of property data including reserves/resources, assays, production, and operating costs. The figures for the specific mines/deposits are given in "range of values" so as to protect the confidentiality of the individual owners/ operators.

Jan 1, 1983

By Robert C. Merritt

This report describes laboratory as well as pilot heap leaching investigations of low-grade sandstone ores from Wyoming, New Mexico, and Colorado. Sodium carbonate-bicarbonate solutions containing sodium hypochlorite extracted up to 86, 54, and 16 percent U308 from Wyoming, New Mexico, and Colorado ores, respectively. Ammonium carbonate-bicarbonate solutions containing sodium hypochlorite were less effective at leaching these ores. Acid leach in replicate pilot plant testing resulted in U308 extractions of 96, 88, and 81 percent from the Wyoming, New Mexico, and Colorado ores. The development of cost-effective processes for extracting uranium from low-grade ore is essential to the assurance of a continuing domestic supply of uranium.

Jan 1, 1977

By R. L. Mazza

This final report on methods of reducing and controlling methane in coal mine gob areas indicates that vertical degas holes are beneficial to the mines of northern West Virginia working the Pittsburgh Coal. The USBM funded project involved the drilling and testing of eight vertical holes (four over longwall panels and four over room and pillar panels) based on a review of 13 previously in existence. Areas of observation included gas production history, flow entry profile, underground methane reductions, strata separations, and casing loads (accompanying subsidence). Observations led to the drilling of successful holes drilled short of the mine. Eleven gas production response to applied vacuum tests were conducted at nine degas holes under the contract. Significant production responses were recorded over longwall gobs.

Jan 1, 1977

By D. Pennington

Ground-water levels and subsidence have been monitored over a longwall panel of a deep coal mining operation located in western Pennsylvania. The monitoring network includes eleven ground-water monitoring wells completed to measure water level changes in separate shallow and deep aquifer zone-, and 50-foot surveyed subsidence stations parallel and perpendicular to the panel centerline. Monthly monitoring data were collected during the premining, mining, and postmining tine periods. Aquifer testing and borehole geophysical logging were conducted during premining, and post-mining conditions to document any changes in aquifer properties and ground-water flow patterns. Results indicate ground-water declines were located with respect to the mining face and mined longwall panel. Dewatering of the deep aquifer zone caused a significant water level decline in deep wells; however, the shallow aquifer zone was isolated fro major impacts by an aquitardal layer during, the, one-year period. Transmissivity data were greatly impacted by fracturing, in the highly anisotropic aquifer system. Borehole geophysical logging indicated changes in ground-water flow patterns and zones of increased fracturing from subsidence.

Jan 1, 1984

Mining and the related extractive and processing industries are chiefly responsible for America's high standard of living. Enormous quantities of sand and gravel, limestone, copper, iron and a myriad of other mineral commodities are required to sustain our growing nation. However, the mineral deposits, both domestic and foreign, are becoming increasingly difficult to find. Adding substantially to the problem, is the fact that the conditions are worldwide. Foreign politics are increasingly affecting mineral commodity availability. Figure 1, taken from Bureau of Mines, "Status of the Mineral industries 1976" illustrates our dependency (in some cases total) on foreign sources for vital mineral commodities. While few nations are capable of exerting an OPEC-like influence on any one mineral commodity, the threat of cartel arrangements and related control strategies is evident. Nationalization of entire industries, once they become self-sufficient, is also exerting a disruptive influence on a large portion of the mineral industries.

Jan 1, 1977

By Jose P. T. Agapito

Several underground coal mines currently operating in the Beckley District of West Virginia are experiencing serious roof and floor problems. A significant portion of the estimated two billion tons of coal resources may be lost as a result of these ground control problems. Preliminary studies by the Bureau of Mines indicated that these problems are due in part to a high horizontal stress field. During this contract study, a field program was conducted to quantify the horizontal in situ stress. A total of 14 overcoring sites (using the Bureau of Mines strain-relief overcoring technique) in five mines were drilled producing 53 data sets. Analysis of the data was done to provide in situ horizontal stresses for each of the five mine, and for the district as a whole. Stress data indicate horizontal stresses far in excess of that predicted by theory and in some cases, up to six times the estimated vertical stress. In addition to the field testing, a detailed computer modeling study was conducted using finite element and boundary integral (displacement discontinuity) methods. Verification of in situ stresses was obtained by the models and analysis of various development geometries, mining methods and remedial techniques were conducted. Recommendations for reducing ground control problems and future studies are presented.

Jan 1, 1980

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

By Piyush K. Dutta

This report describes the design, development and manufacture of production stoper drills and results of their field tests, it is shown that underground stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using these pneumatic drills. The design concept of these drills is a radical departure from the standard valved rifle bar type drill machine design to a drill featuring a valveless independent rotation system, use of an integral muffler and a shroud tube. Six drills were manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1983

By R. Agarwal

The in-situ stress field was determined, using the overcoring technique, at two underground sites at the Pea Ridge Mine, Sullivan, Missouri. At one of the sites in magnetite, the three dimensional stress field showed the largest principal stress to be compressive (-4564 psi), nearly horizontal and closely parallel to the strike of the orebody. The smallest principal stress was also compressive (-2047 psi) and nearly vertical. Considerable difficulty was experienced in drilling porphyry rock at the second test site in the host rock. Only one hole was drilled at this site. The secondary principal stresses obtained in the porphyry are -9464 and -4945 psi, respectively. The-test site in magnetite is located at a depth of 2505 feet whereas the site in porphyry rock is at 2475 feet. The vertical stresses: due to overburden loading at these sites are -3590 and -2782 psi, respectively. Field determined values of the vertical stress are -2207 and -5098 psi, respectively. The variance; between the two sets of values is most likely attributable to the orebody formation and the differences in the modulii of the host rock and the orebody.

Jan 1, 1977

By Robert M. Koerner

The feasibility of using small-scale models to simulate residential masonry foundation walls subject to fatigue loading was investigated. Five wall segments were modeled in one-quarter scale using dynamic similitude equations. The walls were dynamically loaded using a sinusoidal base motion and wall accelerations were monitored. The stiffness, natural frequency response, and damping characteristics were measured. The number of cycles of testing necessary to cause initial visible cracking was recorded. Analysis of the data indicated the importance of the relationship between the forcing function and the natural frequencies of the structure in influencing cracking damage.

Jan 1, 1980