Search Documents

By Sonia Helle, Ursula E. D. Kelm

"From a metallurgical point of view, acid leaching of oxide zone copper ore is considered in the first place in terms of ore grade, whole rock mineralogy, rock granulometry, crushed aggregate size distribution, porosity, permeability and corresponding fluid flow characteristics. Despite exhaustive physicochemical and general mineralogical characterization, drops in copper recovery occur and are often attributed to and “unquantified mineralogical misbehaviour” of the gangue phases. This study establishes an experimental link to monitor and quantify the chemical interaction of chrysocolla, malachite and atacamite with reactive gangue phases.Laboratory-scale sulphuric acid (15%) leaching in small columns is carried out using a synthetic rock composed of 57% quartz, 1% ore phase, and 42% reactive gangue. Gangue phases were selected to represent mineralogy found in argillic, advanced argillic, and propylitic alteration zones. Exotic copper ores of Codelco Norte (in particular Mina Sur) served as model for the modal distribution of mineral phases. Natural reactive gangue phases (<200 Tyler mesh) were chosen as pure as possible: Saz-1 and Swy-1 montmorillonites, KGa-1B and KGa-2 kaolinites (all Clay Mineral Society, USA, Source Clays) Nau-2 nontronite, Imt-1 illite (both Clay Mineral Society Special Clays) and Chilean mordenite, laumontite and bentonite. Ore phases are: mineraloid chrysocolla from Radomiro Tomic (Codelco Norte), reagent grade malachite and a purpose synthesized atacamite-paratacamite mixture. Complete chemical, physicochemical and mineralogical characterizations were carried out for ore and gangue phases.The following observations hold for samples with and without mineralization: Smectite-rich gangue increased up to 75% in volume. Once wet, air-filled vesicles formed due to the rapid sealing effect of overlying smectite in the column. No volume change occurred for illite, mordenite and kaolinite gangues. For kaolinite mixtures acid puddles formed on top of the column during initial leaching due to the delamination and barrier formation of this phyllosilicate. Fluid recovery was <60% for expandable phases and reached up to 80% for non-expandable mixtures. These observations confirm the very low extractions obtained in ore with a combined smectite – kaolinite gangue for Mina Sur. The most important mineralogical changes observed in the solid residues are: reduction of basal smectite phase reflections (XRD), and slight loss of illite intensities. This is also reflected in the major element composition of the residues, which demonstrate a loss of Mg, Mn, Ca, Na, K followed by Fe, Al and Si; with their proportions depending on the starting materials. Furthermore, alunogen and meta-alunogen formed, with related phases coquimbite (illite) and godichite (nontronite) also depending on gangue mineral chemistry. For laumontite samples, meta-alunogen and alunogen precipitated from the leachate."

Jan 1, 2003

By Robert Dunne

A review of the current ?state of the art? of refractory gold treatment will be provided. This will include a global perspective of the refractory processes that are being practiced, where they are and some discussion on why the processes were selected. Some discussion on the challenges that face the refractory gold industry will also be provided.

Sep 1, 2012

By Rintaro Hayashi

The enrichment of useful components from ores and/or wastes has become important with increasing recent worldwide resources demand and the amount of wastes generated from the urban mines, in order to establish real ?sound resource-cycle society? including the activity of resource exploitation. The first stage of the treatment in the process must be comminution and it is important to make good liberation among compositional phases in the targeted resources. Electrical disintegration (ED) is well known to make a selective breakage at phase boundary. However, the detailed mechanism of the phenomena is not clarified yet, in especial, on the influence of electrical properties of compositional materials on the liberation. This paper made a comparison between the liberation degrees of ED products and the results of electromagnetic field analysis using finite element method (FEM). In the experiments, we used several synthetic cement paste based samples in which mineral particles were dispersed to apply the ED, and in the electromagnetic field analysis, we calculated the charge density accumulated and the Maxwell stress at phase boundary. It was found, for highly insulating mineral samples, that higher breakdown voltage was necessary because electric charge was not easily accumulated at phase boundary but that higher liberation degree was obtained after the breakdown (ED). It was also found the tendency that higher liberation was observed for the samples which had higher maximum Maxwell stress calculated by the electromagnetic field analysis. From the results, the electrical charge and Maxwell stress induced at phase boundary could be driving forces of selective breakage. In addition, we also applied the ED to the printed circuit boards (PCBs) in order to concentrate miner rare metals, which were essential for producing electronic devices. It could be demonstrated that the devices installed on the PCB were easily detached from the board and that most of metal elements in the devices was exposed and liberated from the insulating plastic covers, which were broken in the ED, then, it is considered that the subsequent solid phase separation could be effective for concentrating such metal elements. Keywords: liberation, electromagnetic field analysis, printed circuit board, miner rare metal

Sep 1, 2012

By N. Acarkan

Beneficiation of the pyrite concentrate of the Kastomonu-Küre (Northern Turkey) copper ore seems to be attractive due to its high Cu, Co, and Zn contents. Pyrite concentrate were used in the experimental studies. Cu, Co, and Zn were recovered from the concentrate by the sulphatizing roasting, leaching and the precipitation using H2S. Sulphatizing roasting experiments were carried out in a rotary furnace and the optimal roasting conditions were found to be at 650°C roasting temperature and 3.0 h roasting period and addition of Na2SO4 of 3 % for the concentrate containing 0.58% Cu, 0.22% Co, and 0.04% Zn. Then, the roasted product was repeatedly leached with 10 g/L H2SO4 solution. Optimal conditions were found to be 60 oC leaching temperature, 2 h leaching period, and 30% pulp density. Leaching efficiencies for Cu and Co were over 99 %. The valuable metals in the pregnant solution were selectively precipitated by H2S as sulfides. Selective precipitation of Cu, Zn, Co was achieved by adjusting the pH and the temperature of the leach solution. Final metal recoveries of 99.20% Cu, 99.40% Co, and 95.60% Zn were attained. The precipitated sulphides are marketable products. Roasting gases with their 15% SO2 content are suitable for the production of H2SO4 and the leach residues can be integrated with the iron ore processing plant as they contain 57.50 % Fe, 17.70% gangue (SiO2, CaO, etc.), 0.04% S, and 0.06% non-ferrous metals.

Jan 1, 2014

By W. Q. Zhao

In order to raise the utilization rate of phosphate resource of Al-Jalamid Mine in Saudi Arabia, a flotation experiment for its phosphate rock was carried out by using WF-01collector that have been produced by Wengfu Phosphate Mine. The results showed that WF-01 collector had extensive adaptability for Al-Jalamid phosphate rock, and the grade of phosphate concentrate could be up to 33% P2O5 mixing the upper, middle and lower beds rock as well as its 80% more recovery.

Jan 1, 2014

By Harshad Bhagwat

The objective of this work is to investigate the inadequacies of current CFD based methodologies of model development for predicting combustion behavior of pulverized coal in furnaces. In the present paper, a steady state CFD model was used for in-depth analysis of pulverized coal combustion. The model accounts for turbulence, coal combustion, convective and radiative heat transfer and motion of coal particles. It also uses coal combustion models to account for important processes such as devolatilization, combustion of char and the evolution of fuel nitrogen during coal combustion. The model predicts fluid flow, heat transfer, progress of combustion and pollutant formation (NOx, etc.). The model uses several parameters, which need to be tuned with experimental data, which is not only limited in quantity but also insufficient in detail. Various existing methodologies like part calibration method for tuning of the parameters are discussed. In the present work, the parameters associated with coal combustion models were tuned and validated with published data obtained from an experimental furnace using one such part calibration methodology. The results clearly show that the model predictions differed with the experimental data not only quantitatively but also qualitatively. These discrepancies were attributed to part calibration methodology. A detailed parametric study was carried out to demonstrate the importance of parameters from various classes, namely, combustion kinetics, heat transfer, process and geometry parameters, and CFD model parameters. This investigation clearly indicates that parameters from different classes have significant effect on combustion behavior. The discrepancies in current methodology are discussed and a need for comprehensive methodology is highlighted. Keywords: pulverized coal combustion, computational fluid dynamics (CFD), pollutant formation (NOx), mathematical modeling

Sep 1, 2012

By F. O. Milovich, V. A. Ignatkina, L. A. Samatova, E. D. Shepeta

"The aim of the research was to increase technological parameters of the flotation of finely disseminated scheelitecarbonate ore using selective reagent regime.In the studies the monomineral fractions of scheelite and calcite; samples of the scheelite-carbonate ore of the Primorsky deposit with the range of the carbonate module 3-65 were used. A carbonate module of ore is the ratio an initial assay of calcite to an initial assay of scheelite. Sodium oleate, iso-decyl alcohol, water glass, calcium chloride, soda or sodium hydroxide as flotation reagents were used. The flotation method in the Hallimond tube and in a mechanical cell, an adsorption method for study the kinetics of adsorption of oleate and isodecyl alcohol and its combinations on scheelite and calcite, IR spectroscopy including ATR to study the composition of surfacecompounds were applied. Selective reagent regime may include two ways - a combination of collectors or a modification of depressants of calcite and other gangue minerals. On one hand the combination of sodium oleate and higher fatty iso-alcohols of fractions C12-C16 in the rough scheelite flotation to reduce the flotation activity of calcite has been studied. On the other hand depression of calcite flotation by calcium chloride with water glass into rough flotation was used; modified the steaming cycle by Petrov's method applying change the concentration of water glass and other. Fatty iso-alcohols can adsorb on the surface of the calcite that reducing the adsorption of sodium oleate and floatability of calcite has been fallen. Their co-adsorbing with oleat on the scheelite surface were support the hydrophobization and flocculation of slime particles of scheelite. Flocculation of the particles of scheelite leads to increased up 3 times of the recovery of scheelite from the slime class, and calcite change up only 1.4-1.1 times it’s recovery.The growth of the carbonate module more than 11 is decreased the assay of WO3 in the scheelite concentrate of selection cycle."

Jan 1, 2018

By Rod Hocking, Nenad Djordjevic, Randolph Pax

"Semi Autogenous (SAG) mills exhibit complex interactions between the competing processes occurring inside them. Traditional practice is to measure the operation of the SAG mill at an operating point in terms of its load, power draw, steel load, ore throughput rate, water addition rate and more recently the feed size distribution. However significant departures of operating conditions can occur due to changes, for example, in ore hardness, the quest for higher throughputs and mill internal geometry.Fundamental to SAG mill operation are the internal processes that ensure that a given ore throughput and discharge grind size are obtained and maintained. These processes can be measured using non-contact acoustic emissions from the SAG mills which utilise the information rich noise that is generated by the grinding, flow and charge movement inside a mill.Non-contact acoustic in-mill measurements can be used for the validation of discrete element modelling (DEM). The approach being reported in this paper is to model the individual physical processes and then to simulated the assemblage of a physical mill."

Jan 1, 2003

By Elena L. Chanturiya, Vladimir A. Bocharov, Roman A. Amosov

"In many volcanogenic base metal deposits of Russia the gold is closely associated with copper sulphides and pyrite. The recovery of gold associated with pyrite is especially difficult problem.Investigations of gold chemical state and mineral forms in copper-zinc sulphide ores of Gay and Barsuchiy Log deposits in the Urals have been made using EPMA, optic image-analysis, XRA, SEM, thermo-electrical force measurements and selective gold leaching experiments.Two gold varieties are determined: 1) free native gold particles (from 5 µm up to 0,25-1,0 mm), which can be liberated after grinding of ore up to 0,074 µm and named “free gold”; 2)”invisible” gold, including finely disseminated native gold and chemically bound gold. The second variety can’t be disclosed during grinding. Free gold can be recovered by gravitation and flotation while the processing behaviour of “invisible” gold is determined by properties of gold-bearing sulphides: pyrite and chalcopyrite. According to results of diagnostic leaching experiments in ores of deposits mentioned above the part by weight of free gold reaches 70%, the part by weight of the ”invisible” gold is up to 20%. About 10% of gold is enclosed in quartz and acid-soluble minerals.Theoretically (taking into account gold distribution data) it’s may anticipate gold recovery by gravitation up to 60%. However after grinding up to 50-60% of class –0,074 mm only about 40% of gold passes into oversize product including 30% of free gold and 8% of ”invisible” one. It can be recovered by gravitation. Remaining free gold and ”invisible” gold can be extracted by flotation – 25% in total. Inevitable gold losses in tailings may reach 8-10%."

Jan 1, 2003

By Frank Cappuccitti, Stephen Chryssoulis, Stamen Dimov

Surface organic microanalysis of platinum (Pt) and palladium (Pd) minerals by TOF MS1 is an attractive complement and potential alternative to conventional collector screening methods. Its attractiveness lies on its ability to focus on individual Pt and Pd mineral particulates, therefore providing a more targeted approach. The only requirement is knowledge of the occurrence (mineral composition, grain size and association) of Pt/Pd in the feed sample. This newly developed technique can detect, and identify collectors and quantitate loadings on individual Pt/Pd mineral particulates at plant concentration levels. Using this technology, collector loadings were measured on Pt and Pd metal plates and on PtS2 and PdS particulates which had been exposed together to aqueous solutions of different collectors. Thus, data were obtained on collector selectivity, the effect of sulphur; and of depressants, the latter in combination with TOF-LIMS2 results. Staged rougher tests on North American and UG-2 ores linked Pt/Pd flotation kinetics with collector loadings and ultimately grade/recovery.

Jan 1, 2003

By T. Surkova

For the moment reserves of high-grade ores are practically depleted requiring ever-increased involvement of low assay raw materials, such as black-shale ores, in industrial operations. Black-shale ores are constituted of minerals containing such valuable components as vanadium, uranium, molybdenum, manganese, and rare-earth elements (REE). We studied technogenic solutions of black-shale ores processing, after uranium, molybdenum, and vanadium were recovered. Mentioned solutions contain rare-earth elements in substantial quantities (S REE 70-100 mg/dm3) that is very important factor taking into consideration the world demand ever-increasing last years. Higher concentrations of iron and aluminum inhibiting REE sorption and extraction recovery are found in solutions. We propose a method of hydrolytic deposition to cleaning solutions from impurity elements (Fe, Al). Study of hydrolytic deposition kinetics allowed identifying optimal conditions to run this process. Rare-earth elements may be recovered from purified solutions through sorption process followed by their further deposition from eluates in form of concentrates. Keywords: black-shale ores, rare-earth elements, a method of hydrolytic deposition, impurity elements, sorption

Sep 1, 2012

By P. K. Rozakeas

It has been experimentally demonstrated that the application of electrokinetic techniques in the continuous flow of coal-water suspensions within a helical anode-cathode pipe geometry effectively causes a significant reduction in the wall shear stress. This reduction in the frictional force at the cathodic pipe wall surface is attributed to a decrease in the concentration of coal particles in this flow region caused by the migration of negatively charged coal particles towards the anodic surface(s). The disadvantage of flow-intrusive geometries is the reduction in effective flow area as well as an increase in frictional surface area caused by the placement of the anode(s) within the flow region. Experimental data is presented for a non-intrusive helical anode-cathode geometry embedded in the pipe wall which shows that a reduction in pumping energy of approximately an order of magnitude is possible. A sample of sub-bituminous black coal fines having a mean particle size of approximately 17 microns was used to prepare coal-water suspensions with a solids concentration of 50%(w/w). The practical and economic implications of this work relate to an enhanced method of long distance transportation of slurries in pipes as well as an alternative technique for continuously separating solid-liquid suspensions.

Jan 1, 2014

By Michel Brissette, Shaheer Sanuri, Veroljub Mihajlovic

"The main purpose of geometallurgy is to improve the mine planning by mapping hardness and throughput into the mine block model using geostatistics to eliminate the large production fluctuations caused by the ore hardness variability coming from different parts of the pit. However, not all grinding testwork available commercially can be applied to geometallurgy because of large amount of sample required and the associated cost per test. Geometallurgy is now being used in designing grinding mill but as the mining project progress, the accuracy of engineering must improve from 30-35% during the scoping study to 10-15% at the bankable feasibility stage and less than 5% for Engineering Procurement and Construction Management. For SAG milling, the SAG Variability Test (SVT) is an abbreviated version of the standard SAGDesign test developed for this geometallurgical need. The same amount of ore than the original test is ground for three cycles into an open batch SAG test and then the SAG pinion energy is predicted to the standard end point of 80% passing 1.7 mm. For ball milling, a Bond Variability Test (BVT) was also developed using the SAG ground ore from the SVT. The Bond ball mill grindability (Gpb), corresponding to the average of the net grams per revolution from the last three cycles of the Bond test, is also predicted from the third cycle. The relative error for both the predicted SAG ore hardness (WSVT) and Bond Work Index on SAG Variability ground ore (Sv-BVI), in kWh/t, averaged 5.5% and 3.8% respectively compared to the SAGDesign testwork values and are within 7% and 10% respectively from plant benchmark and within 7% from the samples sent to all partner laboratories. Both tests can be continued to measure the true hardness necessary for mill sizing. This article discusses the development of these two new tests, SVT and BVT, their potential use and accuracies in any geometallurgical program."

Jan 1, 2014

By A. Saramak

"The paper focuses on problems of atmospheric pollution by the dusts, produced during the course of crushing and grinding processes, and the main objective of investigative programme is an assessment of emission of particulate pollutants for following crushing devices operated in plant scale: impactors, cone and jaw crushers. All crushers operate in aggregate production plants in Poland. In the first stage of investigations there were determined dust emission levels and supporting characteristics for all crushers under investigation. Then there were introduced indices that allow for comparative analysis in terms of dust emission, for devices with different energy consumptions and comminution ratio. It appeared that crushers with high the overall dust emission do not always achieved unfavorable dust emission per comminution ratio or energy consumption. The introduced indices proved their usefulness, because they helped to carry out a comparative analysis among crushers, operating under different technological conditions. It is also easier to assess environmental impact of individual crushing devices, under analysis. Results of investigations also show that environmental impact of different types of crushers is diverse and it is difficult to compare dust emissions of various types of crushers without taking into account technological aspects (like throughput, comminution ratio, energy consumption, and others) of their operations.INTRODUCTION Mineral processing of raw material is a complex process, involving in general operations of size reductions and separation. Depending on the type of specific raw material, the technological circuit may include operations of comminution and size classification. This is a typical circuit for aggregate production. In ore treatment industry the process in much more complicated and include also a metallurgical treatment of ore concentrate – the final product from processing plant stage.In general, regardless the type of raw material, operations of size reduction are present in each technological circuit of mineral processing. Operations of crushing and grinding are an integral part of processing technology, because they play a crucial role in effective treatment of mineral raw materials (Gawenda 2013). Their duty is to liberate the useful minerals from the gangue in ore treatment industry, or to produce the material with the required particle size in case of aggregate processing. Crushing and grinding operations are of a high negative impact on environment and humans. They consume great amounts of energy, what indirectly contributes to higher emission of carbon dioxide CO2. Apart from energy, crushing and grinding device consume significant amount of steel and other metals and alloys due to high wear of working parts and grinding media. This is also of negative environmental impact due to emissions of additional amounts of CO2 in production of steel and other metals required as spare parts for comminution devices."

Jan 1, 2018

By Hui Zhang, Fei Yang, Tong Guan, Guangqin Fu, Lihong Deng, Yuanlin Chen, Xiaotong Zhou

"For a copper-sulfur polymetallic mine in south China, the main valuable minerals were chalcopyrite, pyrite and pyrrhotite. The flotability of pyrrhotite was similar with chalcopyrite and pyrite and it was easy to be oxidized. As a result, the indexes of copper concentrate and sulfur concentrate were unsatisfactory. Furthermore, the recycling of tailings water ulteriorly deteriorated the technical indexes of copper-sulfur ore beneficiation. After a large amount of experimental studies, under the condition that the tailings water recycling rate was 100%, the copper concentrate with a grade of 22.25%Cu and a recovery of 82.46% on average was obtained for the raw ore containing 0.517%Cu, 15.94%S, 25.46%Fe on average, through using new technology “magnetic separation-flotation” and effective adjustment of parameters in the industrial test which was continuously conducted for 14 shifts in 5 days with a scale of about 75t/d. Comparing with the production indexes (the copper concentrate with a grade of 17.49%Cu, the recovery was 62.27%) during the corresponding period, the grade of copper concentrate increased 4.76%Cu, and the recovery increased 20 percentage points. Besides, the indexes of sulfur concentrate gained a considerable improvement. Currently, the new technology was adopted in the design of the new-built plant with a scale of 7000t/d of this mine. The new technology provided powerful support for the tailings water recycling and indexes improvement of copper-sulfur ore beneficiation.INTRODUCTION Chalcopyrite was usually associated with pyrite and pyrrhotite in copper-sulfur ore. Due to the similar flotability, it was difficult to obtain copper concentrate and sulfur concentrate with high grade. Furthermore, sulfide ore was easy to be oxidized and a large amount of ions formed in the pulp by the dissolution of minerals, which made the pulp become acidic. As a result, pyrite and pyrrhotite were easy to be activated in acidic solution and their flotabilities became stronger. Meanwhile, hydrophilic film formed on the surface of chalcopyrite in raw ore. The flotability of chalcopyrite became weaker and it made the separation of chalcopyrite from pyrite and pyrrhotite more difficult. So it was more difficult for copper and sulfur recovering with the recycling of tailings water containing high content of heavy metal ions and reagents."

Jan 1, 2018

By Kirsten Corin, Margreth Tadie, Michael Nicol, Cyril O’Connor, Jenny Wiese

"The recovery of base metal sulfides has been emphasized in the study of the flotation of platinum group minerals (PGMs). However, in some ore bodies such as the Platreef of the Bushveld Complex, sulfide minerals do not make up the majority of the more significant PGM mineralization. It is therefore important to develop a fundamental understanding of how non-sulfide and sulfide PGMs respond respectively to the current reagents being used in the flotation of these minerals. The interactions between platinum and palladium sulfides and tellurides with the thiol collectors, ethyl xanthate and diethyl dithiophosphate, have been studied using the electrochemical techniques of mineral rest potential and voltammetry measurements. The differences in the interaction between the two types of minerals with these reagents were of key interest. Rest potential measurements indicated stronger electrochemical interactions of the minerals with ethyl xanthate than diethyl dithiophosphate. These measurements also indicated that there are different forms of oxidized collector present on the mineral surfaces after interaction with ethyl xanthates. Voltammetry measurements support these observations and suggest differences of adsorption on Pt and Pd sulfides than on Pt and Pd tellurides. Voltammetry also showed that there was minimal electrochemical interaction between the Pt and Pd minerals and diethyl dithiophosphate."

Jan 1, 2014

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto

"The theoretical technique of computational modeling and the experimental determination of the enthalpy of adsorption of a ligand molecule onto a mineral surface deliver the same output parameters and, therefore, complement each other in investigating the affinity of different ligand types for mineral surfaces.This study ran parallel experimental tests and computational calculations to determine the enthalpy of adsorption of a series of increasing chain length xanthates onto a pyrite surface. The outcomes showed that, while the absolute energy values were different, the trends were similar. Both computational and experimental approaches showed that the extent of the interaction of the xanthate molecule increases with increasing carbon chain length. The computational values were larger than the experimental values, which could be explained, in part, by the addition of water to the computational system, which resulted in a decrease in the heat of adsorption on the (100) surface, compared to the adsorption of the collector in a vacuum. The computational method showed that, in the case of the pyrite (100) surface, the most exothermic reaction was obtained when the two xanthate sulfur atoms bridged two pyrite 5-coordinated iron atoms. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted for each of the C2, C3, C4 and C5 chain length xanthates.The experimentally determined exothermic increase in heat of adsorption for the addition of each CH2 group was found to be -8.17 kJ/mol. The contribution of the thiol head group was -34.9 kJ/mol. Previous studies on self-assembled monolayers have shown that these values are compatible with lateral interactions between CH2 groups and the exclusion of water. This study provides a rigorous experimental and computational approach which is intended to afford confidence in modelled data for the screening of new ligands for flotation processes.INTRODUCTIONComputational modelling is a fast and cost-effective method of screening collector molecules for the efficacy of their adsorption onto mineral surfaces. However, it is desirable to measure the computational outputs against experimental outputs to check for congruency. Computational modelling and experimental microcalorimetry both deliver the same output parameter: the energy of adsorption of the molecule onto the solid surface. These techniques are therefore ideally suited to complement one another in investigating the affinity of the interaction between collector molecules and mineral surfaces."

Jan 1, 2018

By K. Trybalski

Facing the optimization activities, which purpose is to minimize the copper processing costs, the main sources of their occurring were presented. In this purpose, the costs analysis was performed, divided to individual standings, for one of the polish copper beneficiation plants. It was proved, that the main component of the copper beneficiation costs is energy consumption, generated mainly in grinding and classification node, particularly by operating mills. The technological system ? grinding and classification node ? in KGHM Polska Miedz S.A., ZWR region Lubin was then selected to investigation. To evaluate the grinding and classification node, the energetic factors W were proposed, calculated on the basis of the energetic-technological data of process, given by node monitoring system. The correctness of the energetic factors selection to evaluate the work of this node and their practical application in industrial conditions was experimentally proved in other technological object. The selected technological object ? grinding and classification node ? was then mathematically modeled and optimized. The calculated energetic factors were the basis to build mathematical models, identifying industrial copper grinding and classification process. The models described correlation and character of dependency between factors and energetic-technical data of the process. These were regressive and neural networks models. On the basis of factors models, the optimization tasks were determined, which purpose was to select the optimal points of grinding and classification node work. Also, the estimated economical effect, possible to achieve after introduction of given monitoring values to grinding and classification node optimization system, was presented.

Jan 1, 2014

By Zehong Wang

Selecting sodium polyacrylate (PAAS) as grinding aid, the effect of grinding aid on the grinding efficiency of bauxite taken from Shanxi province was studied and its mechanisms were analyzed by measuring the variation of adsorption characteristic, pulp viscosity, surface electric potential of the bauxite and the surface appearance of particles. The results showed that, compared with no grinding aids added the content of -0.074mm in the ground product was increased by 5.45 percentage points under the optimal grinding conditions adding PAAS as grinding aid when the amount of PAAS was 0.7%wt of bauxite. Because the physical adsorption and chemical adsorption were occurred on the bauxite surface, which could reduce the pulp viscosity, change the surface electric potential of the bauxite, enhance the surface appearance of particles and lower the surface hardness of the bauxite, the grinding efficiency of bauxite was increased by PAAS. Keywords: bauxite, grinding aids, grinding efficiency, mechanism

Sep 1, 2012

By M. Özer, G. Önal, F. Arslan

"The use of ultrasonic in industrial processes has increased during the last few years. Ultrasonic vibrations are used in sieving, grinding, ore washing, cleaning, and flotation in mineral industry. There are also some attempts for the utilization of ultrasonic treatment in separation and removal of fine particles from gases and liquids. In Kalemaden A.S. (Turkey) four different types of clay mixtures (1. A mixture of clays from Balikesir-Düvertepe and Istanbul-Sile, 2. A mixture of clays from Ukrania and Balikesir-Düvertepe, 3. Sögüt-Kadikelimesi, 4. A mixture of clays from Sögüt and Istanbul-Sile) and kaolin from Balikesir-Düvertepe (Turkey) are concentrated before their use in ceramic production. Dewatering is the important step in those types of concentration plants. Sedimentation of concentrated clay has always been difficult and taken long times due to their nature and having small particle sizes. Flocculants can be used to enhance the sedimentation, but they are not preferred by the ceramic industry since they affect the quality of ceramic products. For this purpose, ultrasonic treatment is used in the sedimentation of clays mentioned above for solving the problems encountered related to the ceramic industry and promising results were obtained.Kaolin sample, subjected to this experimental study, from Balikesir-Düvertepe region of Turkey was brought from the plant as a pulp in containers and throughly mixed with a stirrer before sedimentation experiments. A two liter graduated cylinder and an ultrasonic bath (with 25 kHz frequency and 0.5 KW power) were utilized in the tests. Superfloc A-120 (1% concentration) was used as a flocculant. The settling distance was reported against the settling time during the experiments. Initial and final pulp densities were also determined. The effects of several parameters such as pulp density, flocculant addition, and ultrasonic treatment on the sedimentation of kaolin were investigated and the results are represented in terms of settling distance versus settling time."

Jan 1, 2003