Search Documents

By David C. Kraft

Helical piles and ground anchors were used to meet critical design and constructability requirements for an urban forest Canopy Walk at the Atlanta Botanical Garden, Atlanta, GA. The 12-foot wide pedestrian walkway path was to be nestled among the treetops of a forest, extending to 600 ft. in length, and soaring 40 ft. high above the forest floor. Of particular concern during construction was that the foundation system for the temporary steel shoring system had to be non-invasive to the subsoil, could not damage the forest floor, trees, root systems, or foliage, and upon completion of the concrete walkway pour, could be removed, again without disturbing the subsoil. Accubrace, Inc. designed and installed all the helical foundation types, as well as provided steel braces, typically used in Tilt-Up building construction, for the walkway project. The braces, some extending to 43 ft. in length, were used to provide lateral support against wind loads for the walkway form. In addition, the braces acted as secondary support for lateral loads during the placement of wet concrete along the 600 ft. length of the walkway. Helical foundation products installed included vertical compression piles, ground anchors for tension rods, and ground anchors for the braces. The installation of the piles and anchors was particularly challenging since the forest floor elevation varied as much as 50 ft. due to the presence of a ravine. Information is provided on the subsoil conditions, required loads, design, installation, and acceptance criteria for each helical product type installed for the project. The results of vertical and lateral load tests on the helical piles in the pre-construction phase, conducted in conformance to project specifications are presented. Photographs to illustrate the nature and complexity of the project are included. The concrete pour for the walkway was successfully completed on December 12, 2009, and the walkway was opened for visitors in May, 2010.

Jan 1, 2011

By John E. Lens

Minutes after the Friday afternoon October 16, 2009 announcement that the 80 year old Lake Champlain Bridge was closed to traffic out of concern for public safety, emergency detour planning started at VTrans and NYSDoT. The closure severed a cross-lake link between Addison, VT and Crown Point, NY, which created a 76 mile detour and significant hardship for commuters, farmers working on both sides of Lake Champlain, and businesses relying on both traffic and employees commuting between Vermont and New York. Rehabilitating the bridge was determined to be economically and technically unfeasible and the design of a replacement bridge was accelerated for a spring 2010 construction start. In the meantime, a temporary ferry alternative was to be rushed into service beside the original bridge by February 2, 2010. This paper presents the case history of the fast-tracked ferry dock design and construction on the Vermont side. Twin 300-foot-long pile supported approach spans, a loading slip system and ice deflectors were designed, fabricated and constructed in 90 days in the fall/winter of 2009-2010. This chronicles the project from initial concepts through the extraordinary cooperation between state and federal agencies, and near round-the-clock winter construction on Lake Champlain. This project and its companion project on the New York shore succeeded by virtue of exceptional cooperation between seasoned regulatory, design, and construction participants and warrant this case-history presentation of the Vermont project to share within the industry as an example of overcoming extraordinary challenges.

Jan 1, 2011

By Jesús E. Gómez

In the Summer of 2011, emergency repairs to the Jefferson Memorial North Plaza and Seawall were completed. These repairs were necessitated by settlement and lateral movement of the seawall and North Plaza which prompted the National Park Service (NPS) to initiate an investigation as to the possible causes of the movement, and commission a design for its mitigation. Information gathered from extensive instrumentation on site led to the design of a movement mitigation scheme that included demolition of the Ashlar Seawall and reconstruction of a new seawall. The new seawall foundation is an A-Wall consisting of vertical caissons and battered pipe piles connected to the seawall itself. The scheme provides resistance to future vertical and lateral movement of the North Plaza and the new seawall. Repair to the seawall and plaza began in December 2009, and was completed in August 2011. This paper discusses the mechanisms believed to be responsible for settlement and lateral movement, summarizes the procedure followed for design of the mitigation, and describes the construction methods and some challenges faced during the repair.

Jan 1, 2011

By Richard Deakin

This case study describes aspects of the design of bridge foundations using 320mm diameter steel tube piles in the vicinity of Montréal, Canada. In this area, these piles are a very commonly used and cost effective solution for deep foundations. Typically they are driven through thick Champlain Sea Clay to bear onto stiff, strong rock. However, in some locations there is a layer of glacial till between the base of the clay and the rock which cannot always be fully penetrated by the piles. There is currently little published information, about the bearing capacity of these piles in the local till, and this paper presents and discusses some pile-test data from a recent project. The nature of the glacial deposits in the study area is presented using information gained from published geological data, the project ground investigations and site observations. The design approach and assumptions are discussed, together with the aims and outcomes of preliminary field driving trials and pile tests. The paper then discusses the results of dynamic tests undertaken on production piles. Bearing capacity factors are back analysed from the dynamic test results and compared against values assumed within the design. Observations are made that designers of future foundations in similar conditions may find informative.

Jan 1, 2011

By Paul J. Axtell

This case history describes the foundation design and construction for the New Mississippi River Bridge, presently under construction in St. Louis, Missouri. The 1,500 ft (457.2 m) main span of the cable-stayed bridge is supported by two delta tower pylons in the river, with anchor piers on each bank. The final foundation design was completed as a part of an Alternate Technical Concept (ATC) proposal by the winning construction team, and utilized drilled shafts up to 11.5-ft (3.5-m) diameter that were socketed into very hard limestone. As part of the ATC foundation design, a full-scale, bi-directional static load test was performed to verify the design and allow use of higher resistance values. This paper presents the results of the site exploration, construction of the load test shaft, details of the load testing, and a comparison of the test results with various design parameters.

Jan 1, 2011

By Mohammed Sakr

The use of helical piles as a deep foundation option has considerably increased in the recent years to support a variety of loads, from small loads for several applications such as residential housing, solar farms, utilities and retrofit projects, to large loads for many applications such as commercial, power transmission lines, oil facilities and industrial applications. Therefore, it is necessary to qualify and quantify their axial capacities and performance characteristics. This paper presents the first full-scale axial compression and tension (uplift) testing program executed on large capacity helical piles installed in cohesionless soils. A total of eleven pile load tests using either single or double-helix piles with shaft diameters that varied between 324 mm to 508 mm (12¾ in to 20 in) were carried out, including seven axial compression tests and four tension (uplift) tests. The results of the axial compressive and tensile pile load tests as well as field monitoring data of helical piles installed in dense sand are presented in this paper. Based on the results of this study it was found that helical piles have developed significant resistance to axial compressive loads up to about 2920 kN (656 kips) and tensile loads up to 2900 kN (652 kips).

Jan 1, 2011

By Les R. Chernauskas

Driven pipe piles are commonly used for near and offshore structures due to their omni-directional bending resistance, large surface area, and ease of installation. However, these piles typically cannot be driven deep enough to develop significant and sustained uplift capacity, and in some cases do not generate enough end-bearing resistance before being overstressed during driving. When driven closed-ended, their relatively light weight to cross-sectional ratio, and when driven open-ended their tendency to prematurely plug, are some installation short comings. Spin Fin® piles are traditional pipe piles fitted with flat, steel plates (?fins?) attached at a slight angle over the lower few feet of the pipe. Their design development dates back several decades for projects associated with harsh, limited weather window, offshore Alaskan oil field work. These projects required a pile type that could generate high and sustained capacity in both compression and tension, at relatively shallow depth. During pile driving, a relatively short, high capacity pile translates into more rapid installations with smaller and more efficient equipment. In this type of environment, where pile capacities are large, cyclic loading is typical, and relatively high pile movement is tolerable, the Spin Fin® pile is a superior solution. This paper describes the experience of using Spin Fin® piles on several recently completed Massachusetts Steam Ship Authority projects.

Jan 1, 2011

By Peter Faust

The foundations for the new South Viaduct Bridge in San Francisco were extremely challenging due to the requirement for very large and deep piles installed adjacent to historic structures. Drilled shafts up to 12? foot in diameter were constructed to a maximum depth of 200? feet in alluvial soils and Franciscan Bedrock using an oscillator system for the installation of the permanent steel casing. This paper provides an overview of the construction techniques, the equipment, and the challenges associated with constructing 12? foot diameter shafts on this very complex project in one of the nation?s nicest landscape setting.

Jan 1, 2011

By Liqun Liang

Various nondestructive testing (NDT) inspection methods are available to evaluate the structural integrity of cast-in-place shafts. The widely used methods include Cross Hole Sonic Logging Testing and Low Strain Testing. Due to its advantages such as low cost, easy operation, quickness and flexibility (no need to plan ahead and prepare inspection tubes or other devices), Low Strain Test is frequently specified in quality assurance programs of many countries or when doubts arise as to the integrity of the finished shafts/piles. The method is well suited for small to middle sized shafts. However it is an indirect NDT testing method and has certain limitations. Data interpretation requires proper training, experience and judgment and, therefore, inconsistent conclusions and reporting may be provided by different testers. To avoid or reduce such inconsistencies, it is best to follow a standardized data interpretation and record classification system. In this paper, a new classification method is presented with examples. A step-by-step data evaluation and interpretation procedure is proposed with examples of real cases to help understand the LST data. The paper also makes recommendations for measures to be taken when anomalies are detected in tested production piles.

Jan 1, 2011

By Walter E. Vanderpool

Full scale load tests are frequently performed immediately prior to deep foundation construction to verify the design assumptions. Occasionally, load tests are performed during design development and applied to the final design for critical and non-redundant structures. We believe that full scale load tests can be very valuable and economical for projects, especially in a geologic environment where the record of full scale load testing is very limited or non-existent. The load testing for the Utah Transit Authority?s Airport Light Rail Trax project provides an example of the advantages of a load test in design development. The savings realized by the owner was in excess of $800 thousand dollars.

Jan 1, 2011

By Timothy C. Siegel

A piled raft refers to a shallow foundation that is structurally connected to the piles, while composite ground refers to a soil-pile matrix where the piles are not structurally connected. The design objectives for both a piled raft and composite ground are (excluding special considerations such as expansive soil): (1) to provide a sufficient ultimate resistance and (2) to distribute the load into the soil-pile matrix so that the settlement experienced by the shallow foundation is within tolerable limits. A simplified model is proposed for a shallow foundation on composite ground where the foundation settlement is estimated as the sum of the downward movement of the piles plus the downward movement of the shallow foundation relative to the pile head. The proposed simplified model is applied using conventional geotechnical analyses for two hypothetical examples of shallow foundations undergoing compression settlement.

Jan 1, 2011

By R. Heath Forbes

The route of a new, 4-mile long, electrical transmission line passed through residential neighborhoods and commercial areas of a small town in the South Carolina Coastal Plain. The new line consisted of 54 new poles and a one-mile underground section. Most of the new poles were constructed within 50 ft of existing structures, and in some cases, within 8 ft to 20 ft. A widely-space subsurface exploration consisting of 20 cone penetration test soundings indicated the subsurface conditions along the alignment generally consisted of saturated, loose to medium dense, fine slightly silty to silty sand. The pole foundations consisted of 20 to 30 ft long, prefabricated ?caissons? (essentially an open-end pipe pile with a prefabricated connection system at the top) with diameters of 28 to 56 inches. The steel caissons were installed with vibratory pile hammers. To help prevent damage and defend against possible allegations from nearby property owners, vibration and settlement monitoring was performed during all foundation installation activities. Limited structural condition assessments were also performed before and after foundation installation. For 53 of the 54 foundations, the ground vibrations recorded at distances coincident with the nearest structure locations ranged from 0.05 inches per second to 1.46 inches per second. With consideration of the dominant frequency, the majority of these values were below the commonly used USBM vibration limits. For a foundation installation that was only 8 ft from the nearest structure, a peak particle velocity of 3.06 inches per second was recorded, which exceeded the USBM limits. For all cases, the measured ground surface settlement was negligible (i.e., less than ¾ inch). Several spurious claims alleging vibration-induced damage were made, but the monitoring program provided an adequate defense. One claim involving artwork that fell to the floor during foundation installation at a distance of 8 ft from the house was deemed legitimate.

Jan 1, 2011

By Saeed Salehi Malekshah

In hybrid foundation system or piled raft foundation (PRF), the raft has adequate bearing capacity and piles are usually required to ensure overall stability of foundation and also to act as settlement reducer for high rise structures. When piles are connected to the raft, a high axial stress may develop and one alternative is to disconnect the piles from raft and consider them as stiffeners for supporting soil. This system is known as disconnected piled raft foundation (DCPRF). Cushion, a compacted coarse grained soil layer, can be used beneath the raft to redistribute and adjust the stress ratio of piles to subsoil and plays an important role in mobilizing the bearing capacity of subsoil and modifying the load transfer mechanism of piles. In this study, finite element method (FEM) has been employed to investigate the effect of different parameters such as cushion stiffness, gap height, raft thickness and piling configuration on the behavior of disconnected piled raft foundation. The analysis is performed on different foundations of hypothetical and real case histories. Results indicate that increasing the raft thickness reduces the differential settlement and pile head axial stress. Concentrating the longer disconnected piles similar to connected ones beneath the central area of raft, decreases settlement of raft. With increasing cushion stiffness, vertical stress ratio of piles to subsoil increases, but settlement decreases. Increasing gap height from 0.1 m to 1 m decreases the vertical stress ratio of piles to subsoil.

Jan 1, 2011

By J. Brian Anderson

Jointed micropiles were investigated to support bridge foundations where shallow rock was present. In this application, micropiles would have some amount of unsupported length, and would be subject to nominal lateral loads. Five lateral load tests were conducted on micropiles to demonstrate the impact of casing joints and rock socket embedment on lateral behavior. Load tests were simulated with FB-Multipier, a hybrid-finite element program for analysis of deep foundations, for proper design of the loading apparatus and instrumentation. The micropile sections were 2 m (6.56 ft) long, 273 mm (10.75 in) in diameter, 13 mm (0.5 in) thick walled, with a 50-mm (2-in) long threaded joint. Micropiles were made of one to three casing sections and were embedded 0.3, 0.6, 1.5, or 3.0 m (1, 2, 5, or 10 ft) into rock. In each test, two identical micropiles were pulled together using a simple frame until the weaker pile failed. All micropiles were instrumented with inclinometer casings while two contained strain gages at 0.76 m (2.5 ft) intervals. Load and displacement were measured at the pile heads. Tests showed the embedment of 0.6 m, 1.5 m, and 3.0 m (2 ft, 5 ft and 10 ft) sufficiently carried lateral loads over 180 kN (20 tons). The piles embedded 0.3 m (1 ft) were not able to maintain lateral load. In general, all micropiles tested to failure exhibited a brittle failure mode where there is small lateral deflection followed by a sudden failure at the casing joint. This was demonstrated in three of the load tests. In most cases, the micropiles were stiffer and stronger in the load tests than originally predicted numerically. The final test, where piles were not loaded to failure, verified that embedding vibrating wire rebar strain meters in the grout captured the bending moment profile of the micropile. The results showed the maximum moment in this case being carried directly across the threaded joint as predicted by the preliminary models. The results of these tests were used to calibrate the FB-Multipier numerical model. Using a load test that included bending strain measurements for a match, the soil properties were adjusted to produce reasonable matches for all of the load tests.

Jan 1, 2011

By Eric S. Lindquist

High groundwater levels combined with variable soil and rock profiles present challenges to the design and construction of deep excavation support systems. Increasingly, secant piling techniques are the preferred technical solution for shoring in these cases. Recent developments in drilling equipment, tooling and procedures allow cost-effective construction of deep, overlapped pile systems to tight tolerances in extremely difficult ground conditions. This paper summarizes critical design considerations for secant pile shoring systems, detailing recent advances in installation procedures and verification techniques that allow secant piles to be used for an expanding range of project conditions. Technically- and commercially-viable secant pile shoring designs require that stringent drilling tolerances be achieved in order to successfully provide combined structural support and groundwater cutoff systems, particularly for unreinforced circular secant pile shafts acting in ring compression. Modern drill rigs and tooling can advance fully cased shafts in geotechnical conditions which range from cohesionless soils below the groundwater table to hard rock, within a single drillhole. Down-hole instrumentation provides verification that tolerance requirements are met and allow secant pile shoring to be used at sites previously considered unacceptably risky. In California, secant pile shoring systems are being used for excavation depths of over 100 ft (30 m) on projects with challenging site conditions. Two case studies are presented detailing severe geotechnical conditions and excavation depths which represent the regional state of practice in secant piled excavation support. These projects provide real world examples of the design, construction and construction verification techniques that permit secant pile shoring to be used in more demanding geotechnical conditions and to greater depths than ever before.

Jan 1, 2011

By Mark Maday

As part of the I-94 North-South Corridor reconstruction program, the Wisconsin Department of Transportation (department) is reconstructing the Mitchell Interchange in Milwaukee, Wisconsin. Located on the south side of Milwaukee near Mitchell International Airport, The Mitchell Interchange interconnects I-94, I-43 and I-894. Reconstruction began in 2009 with the letting of the first advance contract for local crossroad bridge reconstruction. A second advance contract for construction of collector-distributer roads on each side of the I-94 mainline was completed in 2010. The main contract involving reconstruction of the core of the Mitchell Interchange was let in the summer of 2010, and is scheduled to be completed by the end of 2012. The core contract includes construction of three cut and cover tunnels along two system interchange ramps. Construction of the three tunnel structures is on the critical construction path. The contract includes an interim contract completion date that requires the tunnels to be open to traffic by the end of 2011. A top down method of construction using drilled shaft secant piles for the sidewalls of the cut and cover tunnel structures was selected as the preferred structure type to address subsurface and construction schedule challenges. The department identified in pre bid coordination that no cost reduction incentives would be reviewed or accepted for changes in tunnel wall type. A major component of the tunnel structures requires the installation of 1,500, 4-foot diameter secant piles. This paper presents mitigation strategies to manage construction risks associated with the installation of the secant piles including; prequalification of the secant pile subcontractors, requirement for use of full depth temporary casing, a site specific quality control plan, specifying drilling equipment, and developing a geotechnical baseline report for this critical component of the Mitchell Interchange reconstruction project.

Jan 1, 2011

By John G. DiGenova

The Allwell Center Ice Arena at Plymouth State University, Plymouth, New Hampshire is located in the flood plain of the Pemigewasset River. To maintain the arena near the level of the surrounding area, foundation design required use of uplift elements to resist hydrostatic loads caused by frequent flood conditions. Soils beneath the arena consisted of very loose to medium dense alluvial deposits overlying thick glaciolacustrine deposits. Bedrock was encountered at depths of 115 feet (35 m) or more. A mat foundation with a sealed building system was developed for the arena to guard against flood events. Several alternatives were investigated to provide uplift capacity for the mat foundation, including the Rammed Aggregate Pier® (RAP) system, driven precast-prestressed concrete piles, driven H-piles, and deep drilled soil/rock anchors. Evaluations indicated that the most cost effective uplift solution was a tension RAP system that developed uplift resistance in the shallow alluvial deposits. A total of 344 55-kip (245-kN) capacity RAP elements were required for the project. The RAPs were designed to resist tensile loads using threaded steel bars. Dual corrosion resistance was provided to the uplift elements by including sacrificial steel and galvanizing the oversized bars and connection plates. A pre-construction test program was conducted on RAP elements drilled to a depth of approximately 25 feet (7.6 m) and installed using various shaft construction procedures and materials. Ten test piers were constructed and six were tested to verify that the piers could resist 200 percent of the design load with measured deflections of less than 1 inch (25 mm). The RAP system also provided improved bearing conditions for the perimeter wall and mat foundations by densifying and stiffening the upper alluvial soils.

Jan 1, 2011

By Jared M. Green

This paper presents the wall stabilization design and implementation for a 541 linear ft masonry and concrete gravity-type retaining wall flanking the west perimeter of a 7.37 acre parcel in Bronx, New York. This paper will discuss the results of static and dynamic stability analyses performed for the pre- and post excavation phases for the proposed 300 ft wide open-cut of up to 14 ft of contaminated soil below the toe of the retaining wall. The wall stabilization consisted of over 74 inclined drilled and grouted anchor dowels, and 55 tiebacks drilled and grouted to the underlying mica schist bedrock. Three over-lapping rows of jet grout columns were chosen as the foundation solution for the existing retaining wall. This paper focuses on the design, construction and performance of the jet grout curtain wall. The jet grout wall served three purposes: 1) underpinning and excavation support for the removal of contaminated site soils, 2) permanent hydraulic barrier, and 3) resistance against a deep seated failure within the thick clay layer present at the site. The originally designed jet grout wall had unexpected negative effects to the existing retaining wall. The jet grouting program was modified while the Observational Method (Peck 1969) was employed to keep wall movements to a minimum. This paper discusses the diagnostic methods used to determine the cause of retaining wall movement; the implementation of a remedial ground improvement program; the modification to the jet grout installation procedure; and the ultimate performance of the jet grout wall.

Jan 1, 2011

By Markus Schönit

Double rotary drilling combines continuous flight auger drilling with a casing for producing a cast-in-place pile. When producing a pile an outer casing and an auger (hollow auger) rotating inside the casing are driven into the ground in counter-rotation. The outer casing serves to support the surrounding soil and the inner auger excavates the drilling cuttings to the surface inside the casing. After reaching the projected drilling depth concrete is pumped through the hollow stem of the auger and outer casing and auger are extracted. After their complete extraction a reinforcement cage can be inserted in the fresh concrete. Compared to Kelly drilling the double rotary drilling method offers numerous advantages, including, for comparable diameter and length, shorter production times and higher accuracy (pile inclination and excess concrete) combined with increased occupational safety and lower noise emissions. Moreover, pile tests have proved that piles produced by double rotary drilling feature higher axial load-bearing capacities than comparable piles produced by Kelly drilling. This article offers an overview of the basic theoretical principles of double rotary drilling lists the required and currently available machinery and, finally, discusses the results and conclusions of a current jobsite.

Jan 1, 2011

By Gerald E. H. Verbeek

As the number of driven concrete piles with Embedded Data Collectors increases, it has become possible to compare the widely used Beta Method to assess pile damage (using the change of pile impedance) with the so-called Measured Pile Integrity (MPI) method (a combination of two approaches using both the change of pile impedance and the change in pile pre-stress levels). After a brief introduction of both methods, this paper presents the outcome of that comparison based on data from more than 400 concrete piles driven in Florida, which brings into question the reliability of any damage assessment method based solely on the change of pile impedance (such as the Beta Method), especially to detect damage near the pile toe. Moreover the paper demonstrates the need to re-assess the damage classification used for the Beta Method as well as the use of Pile Driving Analysis (PDA) to detect pile toe damage.

Jan 1, 2011