Search Documents

By Roger A. Bullivant

As the UK's foremost domestic foundation underpinning contractor over the last 25 years it has become abundantly clear that the size of the repair market, some £500m per annum is a significant waste of resource and cost. To experience this scale of foundation failure in mainly new construction less than 20 years old is unacceptable. This is being further endorsed by our contracting experience in the USA over the last 10 years. Our foundation repair systems are mainly based upon the use of driven mini piles and it was considered appropriate that this type of pile should be upgraded and used on new build construction where the ground was marginal or bad.

Jan 1, 1995

By Alok Bhowmick

The most uncertain and challenging part of a bridge design and construction is the ‘Choice of foundation’. During the planning and conceptual design stage, it is extremely important to choose the right type of foundation. Wrong choice can lead to disaster for the project. This paper will present three interesting case studies of past bridge projects, to demonstrate how correct choice of foundation can help to meet the project commitments while the wrong choice of foundations can led to huge delay in project completion, leading to time and cost overrun.

Nov 1, 2022

By Amy B. Cerato, Shawn Allred, Tatiana Vargas

"Helical piles are deep foundation elements that resemble, and are installed like, a large steel soil screw — they have a slender steel shaft with one or more round helix bearing plates welded to the shaft to provide support to the structure they hold. Helical piles are rotated into the ground with a large torque motor and provide support through soil bearing on the helix bearing plates and along the shaft. The piles are available in many lengths and, due to their small footprint along with their ability to create minimal disturbance to surrounding structures, they are often used in urban settings for foundation repair, retrofitting existing buildings and for new construction projects. Helical piles are routinely installed as foundation elements in seismically active areas, such as New Zealand, Japan and the U.S.Anecdotal observations (e.g., from New Zealand, Japan and the U.S.) have shown that piles with a comparatively small cross-section and high anchoring capacity, such as helical piles, are beneficial for seismic resistance. This is presumably due to the pile’s slenderness, higher damping ratios, ductility and resistance to tipping uplift. In New Zealand, it was observed that helical pile foundations fared much better than driven and drilled concrete piles after the 2011 Christchurch earthquake. In a personal communication, Woods (2016) described that, out of the 300 structures in center city Christchurch that were supported by helical piles, fewer than 10 structures suffered significant structural damage. However, many structures supported by driven and drilled concrete piles were damaged to such an extent that they were condemned and subsequently demolished."

Jan 1, 2017

By Dave P. DeClerck

Hardman Construction was faced with the challenge of completing a large earth retention project on a constricted downtown Detroit site, while maintaining a safe and productive worksite. To do so, new technologies using robotic equipment was instituted. HISTORY The historic J.L. Hudson Building (Hudson’s) in Detroit, Michigan was the premier retailer in the city’s downtown district from the 1890s through the 1960s. The massive flagship store sat at 1206 Woodward Avenue, one of the busiest streets in the Detroit area. Hudson’s broke ground in 1891 and would go through twelve renovations and expansions. The last renovations took place in 1946, which gave the building the title of being the largest department store in the world at the time. It spanned an entire city block and boasted 2.2 million square feet of retail space. By the 1970s, Detroit was in an economic downturn. The Hudson’s department store finally closed its doors in 1983. Besides a few working offices, the building sat vacant. The building was unique in that it had four levels underground, offices, mechanical areas, and equipment storage. Following years of neglect, the Hudson’s building was seized by the state and transferred into the hands of the city. The city had it demolished in 1998, (shown in Fig. 1) to construct a new, four- level underground parking garage as well as a potential future above-grade development (Sewlck, 2017). The building was imploded in one of the largest implosions of that time. The building rubble filled the underground rooms and helped to stabilize the exterior concrete walls and keep them from collapsing.

Jan 1, 2019

By Christopher J. Ramsey, Don W. Dotson

"An existing four lane section of US 27 was widened to eight lanes. The project lies in the rugged Valley and Ridge Province of the Appalachian mountains starting at the Tennessee River in Chattanooga, Tennessee and extending 2.6 km north to Signal Mountain Boulevard. This terrain presented many challenges to accommodate the road widening in the narrow, rugged topography. Multiple tiered wall systems consisting of large tieback walls, post-tensioned reaction blocks, and gravity MSE walls for a total of approximately 30 retaining walls were required. The retaining walls served to stabilize the thrust faulted geology while also minimizing right-of-way acquisitions. The cut walls consist mainly of a tiered system of tied-back soldier piles walls with cast-in-place concrete facing. Cast-in-place pile shear walls were required along the toe of existing MSE walls to maintain stability during construction. This paper discusses the design methodology, which includes a hybrid (rather than traditional) earth pressure diagram intended to reduce life-cycle maintenance and long-term performance. Further this paper addresses wall construction, slope stability analysis, landslide mitigation alternatives, soldier pile wall design features, site challenges, monitoring and performance (to date) of the wall systems.INTRODUCTIONThis project involves the proposed widening of US Highway 27 (State Route 29) from the north end of the Tennessee River Bridge at Manufacturer’s Road to State Route 8 (Signal Mountain Road), approximately 2.64 km of roadway (Fig. 1). The project site is located adjacent to the Tennessee River on the north side of downtown Chattanooga, Tennessee in Hamilton County. The existing, limited access highway is to be widened from four lanes (two northbound and two southbound) to a minimum of eight lanes. Some portions of the alignment will expand to as much as ten lanes where northbound and southbound ramp acceleration/deceleration lanes coincide.In addition to the number and heights of cuts and fills involved, a major factor in determining an economical design for the alignment is the complicated geologic conditions along the roadway alignment. The existing roadway is situated between several steep cut slopes, some of which are only marginally stable or currently exhibit signs of instability. Due to the proximity of the project to the downtown area, the steep slopes along the alignment, and the relatively dense population near the alignment, widening the pavement and constructing cut and fill slopes to a stable configuration would result in major land acquisition for slope right-of-way."

Jan 1, 2015

By Kento Miyamoto, Kazuki Imamura, Takayuki Tanaka

"Global economic development has drastically increased energy consumption in various fields, and CO2 emissions, which are a prime cause of global warming, have continued to increase. Therefore, measures for reduction of the load on the environment have been taken in various areas. Energy improvements of various types of work vessels used for offshore construction might be expected to greatly reduce consumption of fossil fuel, because many of these vessels are larger than land construction machinery and consume large amounts of fuel, which will lead to effective use of resources and alleviation of the load on the environment. However, such efforts are unusual because renewal or newbuilding of work vessels is rare. We developed a work-vessel hybrid energy system based on fuel-saving technology and use of natural energy to promote reduction of CO2 emissions for a large deep mixing barge in 2010. We developed an Automated Generator Start-Stop System, which automatically controls the number of active generators according to power demand during ground-improving work of the deep mixing barge in 2012, thus further improving the work-vessel hybrid energy system. These systems are introduced here.INTRODUCTIONIn recent years, CO2 emission, which is one of the factors of the Global Warming has been increasing. According to the report by National Institute for the Environmental Studies in Japan (2014), CO2 emission in Japan has amounted to 1,276 million tons. The industrial sector in the total emission becomes 500 million tons that is equivalent to 39%. Meanwhile, the offshore Deep Mixing Method requires work vessels mounted with a large power plant (Fig. 1). In sea ground boring, very large load acts on the deep mixing machine, and the large power is required, which results in the increase in CO2 emission. To achieve eco-friendly marine construction, the work-vessel hybrid energy system was developed. Table 1 shows specifications of the deep mixing barge with the work-vessel hybrid energy system."

Jan 1, 2015

By Charles G. Crans, Naresh Gurpersaud

"Toronto’s Union Station, a National Historic Site occupying an entire city block, is the busiest commuter rail transportation hub in Canada. An extensive project is being undertaken to revitalize Union Station while maintaining the historical significance of the building and minimizing disruption to commuters. A significant stage of the revitalization involves excavation indoors, to a depth of up to 5.5 m below the existing floor level to create space for a new transit concourse and a new lower-level pedestrian retail concourse. A hybrid excavation support system utilizing micropiles as soldier piles was constructed over an 18 month period between 2010 and 2011.Development and testing of connections between the micropiles, shotcrete facing, lagging, walers, and tiebacks presented significant challenges. The existing viaduct structure was constructed in the 1920’s on land reclaimed from Toronto Harbour, so there was significant (and ongoing) uncertainty with respect to buried obstructions including relic timber wharfs and abandoned steel and timber piles. Collectively all these conditions precluded the use of conventional methodology; new techniques, installed using modified equipment, and for the first time in the Greater Toronto Area, were required.Details of the existing site conditions, installation challenges, design, construction and performance of the hybrid excavation support system inside this historic structure are presented.INTRODUCTIONUnion Station in Toronto, Ontario is the busiest passenger rail facility in Canada, with 65 million passengers annually and an average of 200,000 passengers each day. Construction of the station was completed in 1920. It has been designated a National Historic Site of Canada and inducted into the North America Railway Hall of Fame in the Facility and Structure category.The Union Station Revitalization Project (USRP) was tendered in 2010 and awarded as a 6-year, $450M construction management / trade contract package. Included was a large scale grade reduction, referred to as “The Dig Down”, to create two basement levels and this required extensive excavation support constructed entirely indoors within the active station setting."

Jan 1, 2017

By Michael J. Weaver

Urban redevelopment projects are occurring more frequently than ever before as urban greenfield sites become limited and city planners and devel- opers attempt to revitalize existing underdeveloped neighborhoods. How- ever, because of the past usage of many urban sites (some dating back 100 years or more), designers and construction teams have to not only engineer founda- tions to accommodate the subsurface soil and ground water conditions, but also to work around the relic founda- tions or structures that have been left behind from previous developments. In these cases, a one-size-fits-all approach to foundations may not yield the most cost- and schedule-effective approach, and hybrid foundation systems have to be evaluated.

Apr 1, 2022

By Graeme Smart, Thomas Fiala

"Yorkville Plaza II, a 40-storey signature condominium residence, is scheduled to open on Avenue Road in Toronto’s prestigious Bloor-Yorkville neighbourhood in spring 2017. In close proximity to Toronto’s subway system, the new tower requires six levels of underground parking, founded in wet, silty sand.Isherwood Geostructural Engineers (Isherwood) was retained in April 2012 by developer Camrost-Felcorp to provide a shoring and excavation solution to address the challenging site conditions. A 31-storey upscale residential building under renovation with three levels of parking, owned by Camrost-Felcorp, flanks the site on the north. Situated on the eastern border is a 7-storey building with three levels of parking. Avenue Road, a four-lane arterial road that brings heavy commuter traffic into downtown Toronto, runs along the western border, and on the southern border of the site is a busy City road that brings traffic into the popular Yorkville area. The tunnel for the Toronto Transit Commission’s (TTC) overburdened east-west subway is located 14.5 m to the south, running below an existing 26-storey neighbouring building. Electrical and communication utilities (Bell) are closely located along the southern side. Non-documented existing excavation shoring, installed in the early 1970s, on the southern and western sides compounded the difficulties presented by the TTC tunnel.This paper presents the unique, non-conventional hybrid shoring solutions Isherwood developed to address the challenges presented by the site, as well as other complications that surfaced during the project: non-encroachment requirements (no tiebacks) beneath uncooperative neighbours, tight geometry to install shoring, and Toronto’s two coldest winters in decades.THE PROJECTBecause of circumstances associated with this site, for this project Isherwood designed two unique shoring walls which drew on their experience and expertise they had gained over the last 40 years. The following is the story of this site:Yorkville is an affluent neighbourhood in the heart of Toronto with a vibrant mix of high-rise towers, residential homes, tony restaurants and flagship shops. The development requires six levels of underground parking (a 20m deep excavation), with three levels undermining the high-rise buildings to the north and east and extending into wet, silty sand.Isherwood was retained in the spring of 2012 to design the excavation shoring. Isherwood’s scope also included field support, design, verification and monitoring. Finite Element Analysis was employed to confirm Isherwood’s design and anticipated movement of the south shoring wall and the TTC subway tunnel.The existing site was severed in two, with the proposed condominium tower slated for the southern portion. On the north half of the site stands a 31-storey building (Yorkville Plaza I at 21 Avenue Road), with three levels of underground parking, sitting on belled caissons which were one foot from the back of the proposed shoring wall so this would have to be considered in relation to the design and drilling methods. Constructed in the early 1970s, Yorkville Plaza I is currently being converted from the Four Seasons hotel to luxury condominiums by Camrost-Felcorp. To the east, directly adjacent to the proposed shoring, stands a 7-storey building (164 Cumberland Road) with three levels of parking, supported on spread footings founded on stiff clayey silt. The tunnel for the TTC’s busy east-west subway, a double box structure built by cut-and-cover in the 1960s, is located 14.5 m to the south, 9 m below grade, and running below an existing 26-storey building. Bell fibre optic communication cables and electrical lines, along with storm and sanitary sewers, are situated on the south and west sides of the site, leaving limited room to install shoring. Due to the heavy volume of commuter traffic on the four-lane arterial road (Avenue Road) to the west, site access and lane closure were not permitted here."

Jan 1, 2015

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid Deep Mixing (DM) shoring system was recently constructed for a high-rise development in downtown Vancouver, British Columbia, Canada for the temporary support of a five-level basement excavation. The site is bounded by an existing bridge off-ramp structure along its longest side and by city streets on the other two sides, which formed a truncated triangle in plan. A conventional secant pile wall was installed along the longest side, about 380 ft (116 m) in length, of the site. Hybrid shoring walls (HSW) 1 and 2 were installed along two shorter sides with each being 235 to 246 ft (72 to 75 m) long. HSW 3 completed the excavation support system along the shortest side with a length of about 55 ft (17 m). Cutter soil mixing (CSM) was proposed by the excavation and shoring design-build team in lieu of conventional secant piling. CSM was the preferred method to construct the infill panels between soldier piles because of the speed at which the shoring system could be constructed in the variable fill, peat, wood waste and overburden. Design ConsiderationsTo minimize the impact on buried utilities along the outside perimeter of the excavation, the temporary shoring was designed to limit the lateral displacements to less than 0.8 in (20 mm). Factors taken into consideration for shoring design included the lateral earth pressures from the fill and native soils, groundwater pressures, temporary construction loads (e.g., crane or heavy plant/equipment), and permanent structural requirements. The subsurface conditions at this site typically consisted of fill (cohesive and granular), overlying peat and/or wood waste, overlying clayey silt to sandy silt, overlying weathered to dense to very dense clayey silt till to sandy silt till with silt layers. Localized, perched groundwater was observed within the fill, peat, wood waste and sandy silt layers above the dense till."

Jan 1, 2017

By Donald Deardorff

Helical piles often rely on the final installation torque for ultimate capacity verification. When helical piles are designed using traditional bearing capacity equations for deep foundations and field monitored for a specified final installation torque, a factor of safety equal to 2 is often allowed for the design. One of the more common methods of determining torque during helical pile installation is by correlating the differential pressure across a hydraulic gear motor to a torque. Most drive head manufacturers provide multipliers to convert differential pressure to torque for different drive head models. These multipliers are based on theoretical torque equations and vary with the planetary gear ratio, hydraulic gear motor displacement and drive head efficiency. Drive head manufacturers show a linear fit between the differential pressure and output torque with no scaling effect. Previous drive head testing performed by the author has confirmed that the drive head differential pressure to torque relationship is generally linear however there is a scaling adjustment needed. This results in a variation of multipliers across the differential pressure range for a given drive head. Eight hydraulic drive heads from three manufacturers were field tested by Foundation Supportworks, Inc. to compare the torque versus differential pressure curves with varying installation equipment, hydraulic line sizes and hydraulic flow rates. Differential pressure was monitored using three methods including pressure gages, PT-Tracker and an Ashcroft AT-100. Flow and temperature was measured using a Webtech system analyzer. Torque was measured using a Pro-Dig in-line torque transducer, a TruTorque indicator and a Chance Mechanical Dial in-line torque indicator. The current testing indicates that a change in installation equipment and/or a change in hydraulic flow rate may affect the torque versus differential pressure curve of a given drive head. The results of this testing also show that some of the methods for determining torque during helical pile installations may be unconservative, thereby resulting in safety factors less than required.

By Donald Deardorff

"Helical piles often rely on the final installation torque for ultimate capacity verification. When helical piles are designed using traditional bearing capacity equations for deep foundations and field monitored for a specified final installation torque, a factor of safety equal to 2 is often allowed for the design. One of the more common methods of determining torque during helical pile installation is by correlating the differential pressure across a hydraulic gear motor to a torque. Most drive head manufacturers provide multipliers to convert differential pressure to torque for different drive head models. These multipliers are based on theoretical torque equations and vary with the planetary gear ratio, hydraulic gear motor displacement and drive head efficiency. Drive head manufacturers show a linear fit between the differential pressure and output torque with no scaling effect. Previous drive head testing performed by the author has confirmed that the drive head differential pressure to torque relationship is generally linear however there is a scaling adjustment needed. This results in a variation of multipliers across the differential pressure range for a given drive head.Eight hydraulic drive heads from three manufacturers were field tested by Foundation Supportworks, Inc. to compare the torque versus differential pressure curves with varying installation equipment, hydraulic line sizes and hydraulic flow rates. Differential pressure was monitored using three methods including pressure gages, PT-Tracker and an Ashcroft AT-100. Flow and temperature was measured using a Webtech system analyzer. Torque was measured using a Pro-Dig in-line torque transducer, a TruTorque indicator and a Chance Mechanical Dial in-line torque indicator. The current testing indicates that a change in installation equipment and/or a change in hydraulic flow rate may affect the torque versus differential pressure curve of a given drive head. The results of this testing also show that some of the methods for determining torque during helical pile installations may be unconservative, thereby resulting in safety factors less than required."

Jan 1, 2017

By Patrick Bermingham

The advancement of hydraulic impact hammers has followed the general advancement of hydraulics. The construction industry has been revolutionized by the application of hydraulics in excavators, cranes and, of course, in the hydraulic vibratory driver/extractor, which has become a standard tool. The innate ability to move a large mass with a very small displaced volume has given hydraulic power the advantage over previous power mediums. Recent development of more specialized and complex seal configurations and compounds has greatly improved the reliability and permitted the use of higher pressures in hydraulic systems.

Jan 1, 1987

By Michael Arnold, Bob Faulhaber, Joe Nichols

"Center Hill Dam is a critical part of the infrastructure controlling floods at the Caney Fork River and reducing flood levels at the Cumberland, lower Ohio and Mississippi Rivers. The Center Hill Dam Foundation Remediation Project was necessary to address Karst features in the foundation rocks and observed signs of distress of the dam. From 2011 to 2014 BAUER Foundation Corp. (BFC) performed deep foundation works for this project. The executed features of work include the installation of two walls. The first wall extends throughout the clay embankment into the underlying rock to provide encasement during the construction of the second wall. Its width of 7.4 feet makes it the widest diaphragm wall ever installed. The second wall is the actual seepage barrier and provides a continuous 2- feet wide wall. It extends through the first wall into the underlying rock and is up to 300 feet deep. The paper introduces the project, the requirements specified by United States Army Corps of Engineers (USACE) for encasement and barrier wall and the approaches taken by BFC. It discusses the ground conditions and describes the excavation equipment as well as the excavation methods used. A special focus is put on the steering capabilities of the hydrocutter equipment and the verticality performance.PROJECTBeginning in 2011, BFC was tasked by the USACE with the installation of a seepage barrier/cutoff wall at the Center Hill Dam Foundation Remediation project under a partially performance based specification. The remediation was necessary due to karst features in the foundation rocks and observed signs of distress, which led USACE to rate the dam with the most critical dam safety action classification (DSAC I). The executed features of work include the installation of two walls. The first wall, an encasement wall, extends vertically through the clay embankment and is embedded minimally into the underlying bedrock to provide embankment stability during the construction of the second wall, the barrier wall. The encasement wall is constructed of overlapping panels 7.4 feet (2.25 m) wide, which is the widest diaphragm wall ever installed, and up to 210 feet (64 m) deep. The second wall is the seepage barrier and provides a continuous 2 feet (0.6 m) wide wall consisting of overlapping panels. It extends through the encasement wall into the underlying bedrock and is up to 307 feet (93 m) deep. BAUER BC40 and BC50 hydrocutters mounted on MC96 and MC128 foundation cranes were used to perform the majority of the works (Figure 1). Excavations were performed under bentonite slurry (encasement wall) and water (barrier wall) and concrete was poured with the tremie method. Adding to the challenges, the project had to be executed in an environmentally sensitive area. Based on the high risk, a special focus was put on monitoring, quality control and geometric accuracy. The WallTracker information management system was used to share all relevant data between BFC and USACE (Roff et al. 2014)."

Jan 1, 2017

By Steven Dapp

A new hyperbolic model for generating P-Y curves is developed for use in lateral analyses of cemented soils (a ?C-F? soil with both cohesive intercept and friction angle), and includes degradation of the static loading soil response to model the effects of load cycling (repeated loading) with load cycle number. The p-y curves, for both static and cyclic loading, were derived from full-scale lateral test results conducted on a set of six drilled shafts in a loess deposit at the Kansas DOT test site. Values of the model parameters obtained from the load testing at this site are presented, as well as a discussion of the model parameters effect on the results such that the model may be rationally applied to other sites with C-F type soils. A step-by-step procedure is presented to illustrate the application of the model. Correlation of the model to the CPT cone tip resistance (qc) from CPT testing is made, as this was found to be the most reliable; However, the model is applicable to other methods, both in-situ and laboratory, of assessing the soils strength.

Jan 1, 2011

By James A. Mason

The State of California has instrumented numerous buildings, bridges, and dams throughout the state with earthquake recording devices. These accelerometers are strategically placed to measure the response of the structure to a specific seismic event. This comprehensive program enlightens the field of seismic engineering after each earthquake. The Office of Strong Motion Studies, California Strong Motion Instrumentation Program, a sub-branch of the Division of Mines and Geology, provides a professional service unequalled in the world. Within hours of a local earthquake, a preliminary report with the epicenter / hypocenter, structural damage, and time history records are available to all interested parties. The included partial report in the appendix, see section 5.1, is one of the reports that C.S.M.I.P. produced after the Loma Prieta Earthquake of October 17,1989. The diagram on the cover is even of interest. This is a small portion of San Francisco. The values on the diagram are the recorded maximum horizontal ground accelerations at that location in the city. For example, the acceleration at Yerba Buena Island was 0.06g. (The "g" refers to the acceleration of gravity. Thus, a 0.06g acceleration refers to the force, F=m*a, that the structure would experience. For this case, the force would be six percent, 6 % , of the mass of the structure.) Yet, directly on the other side of the Bay Bridge, at Treasure Island, the acceleration was 0.16g. Yerba Buena Island is a natural island composed of hard granular material. Whereas, Treasure Island is a man-made island of imported filled. Here one can see the absorption / transmission difference between hard material, which interact with short seismic wavelengths, and soft cohesive material, which interact with long seismic wavelengths.

Jan 1, 1993

By Georgette Hlepas

How often phrases like these have been made by project managers and project teams trying to explain why there has been cost growth, project delays and differing site conditions claims. But does it really take x-ray vision? Do we really approach geotechnical construction projects unprepared for the subsurface that may be encountered because we can't get the answer? Too often our industry seems to think the answer is, "yes." However, this is not because we can't understand the subsurface. All too frequently it is because a choice is made to save money or time by foregoing or shortchanging upfront subsurface investigations. This is accepting a risk at the beginning of the process and realizing it during construction. Case histories have proven time and time again that upfront investment in site exploration and constructing a ground model mitigates risk in design and construction. But how much do we prepare? What level of investigation (or investment) is appropriate? The answer of course, is it depends; how much risk are you willing to take for your project and what are the potential consequences?

May 1, 2022

By Sheryl D. Gallagher

The project consisted of filling an abandoned underground limestone mine to facilitate construction of a new entrance ramp to I-470 in Lee?s Summit, Missouri. Due to collapse of mined areas near the project site, design included determination of the limits of remediation for the project and minimum construction requirements for mine infilling. The Judy Company, contractor selected for the mine infilling, experimented in the laboratory with several grout mixes to determine the appropriate mix for the project. Infilling was accomplished from the ground surface, and camera observation was used to monitor the barrier wall construction and infilling process. It was discovered that some of the mapped rooms were larger and some were smaller than indicated on the construction plan.

Jan 1, 2009

By Darrell L. Beddard

The test program information provided for some immediate changes on the upcoming contracts and in contract administration for the I-880 Replacement Project. Plan sheet modifications included changes to the pile data tables showing the actual demand load required for structural stability. The normal class of pile with a minimum load carrying capacity was removed. This provided for substantial pile length reduction at several locations since the structural loading was much less than the predetermined pile class ultimate capacity. New specifications were developed and standard specifications were modified to accommodate the newer foundations, installation procedures and pile acceptance criteria. Current Caltrans specifications require that the Contractor provide bearing capacity at the specified tip elevation. This requirement was removed and pile acceptance was determined by the Engineer. Acceptance criteria was established by the State and was based on. set-up trend over time. Static loading tests were reduced especially in areas where testing was performed on the indicator program. Testing procedures were modified and set-up periods were established before piles could be tested. For the contract near the San Francisco Oakland Bay Bridge (Unit E) the FHWA 1000 tons (8.9 MN) test beam configuration was completely changed. This provided added safety and allowed more tolerance in the pile placement for the testing operations. Indicator piles were added as companion piles to the static loading test piles. These piles were used for restrike events which included collecting dynamic data for calibrating the wave equation analysis with static load test results. Indicator piles also provided quick access for restrike events, where as, the static loading test pile needed modification to perform the restrike operation. Penetration rates were recorded for these operations. Wave equation Analysis Program (WEAP) was used in developing the acceptance criteria. The standard Engineering News Record (ENR) formula in the current Caltrans' Standard Specifications was removed for the contracts. Contractors were required to submit, prior to driving piles, a driveability study for their contract. These studies required discussion of their operations, method of installation, effects of soil set-up, set periods, hammer settings, bearing graphs, inputs to the WEAP program and complete a "Pile and Driving Equipment Data" form. Dynamic monitoring was detailed in the specifications on how the monitoring process was to occur. Set periods were established and restrike events were called out with the frequency of these events.

Jan 1, 1996

By Darrell L. Beddard

The Loma Prieta earthquake occurred on October 17, 1989 at 5:04 PM, Pacific Daylight Time. It measured 7.1 in magnitude and was felt from Los Angeles north to the Oregon state line and east to western Nevada. The epicenter of the earthquake was located along the San Andreas Fault, in the Southern Santa Cruz Mountains just north of the City of Watsonville, California. It was the largest earthquake to occur in the San Francisco Bay area since the 1906 earthquake. A total of 87 aftershocks of Magnitude 3.0 or larger were recorded within 21 days after the seismic event. As a result of this earthquake thirteen State-owned and five locally-owned bridges were closed to traffic. Three of the most publicized State-owned structures closed to traffic were Struve Slough Bridge, San Francisco-Oakland Bay Bridge and Cypress Street Viaduct. Struve Slough Bridge was twin slab bridges that collapsed and were rebuilt and open to traffic three months after the earthquake. San Francisco-Oakland Bay Bridge experienced collapse of upper and lower spans at Pier 9 and was reopened to traffic one month after the earthquake. The Cypress Street Viaduct experienced collapse of 48 bents that resulted in the upper roadway falling onto the lower roadway.

Jan 1, 1996