Search Documents

By Nihal Bohra

A temporary bridge, supported on steel pipe piles, was built to expedite the construction of a breakwater structure off the western coast of Peru. The bridge provided access for dump trucks to the breakwater across a 342 m (1122 ft.) wide navigation channel from a liquefied natural gas (LNG) loading facility, at the end of a 1.3 km (0.82 miles) long permanent trestle, in 15 m (50 ft.) water depth. After the completion of the breakwater, the temporary bridge was removed, and the piles were extracted approximately one year after the initial driving. The bridge deck was typically supported on pairs of 914.4 mm (3 ft.) diameter, 18 mm (0.708 inch) wall steel pipe piles spaced at 7.5 m (24.6 ft.) across the bridge width and 18 m (60 ft.) along the bridge length. In an attempt to reduce the driven pile embedment, an inner closure plate was installed at 2.7 to 7 m (9 to 23 ft.) from the pile toe to force closed-end behavior. The piles were designed to carry 3400 kN (383 tons) axial compression load, and a minimum of 8 m (26 ft.) embedment was specified to provide sufficient resistance to the lateral loads. The subsurface conditions consisted of cemented conglomerate of sand, gravel, pebbles and some boulders, locally known as the Cañete Formation. The driven pile embedment varied widely, between 8 to 24 m (26 to 79 ft.). A significant portion of each pile was above the seabed, passing through seawater and up to the bridge deck, and was therefore unsupported. The extraction of the piles was challenging due to the subsurface conditions, presence of significant water column, pile weight, and the inner closure plate. Several different approaches were attempted before the piles could be successfully extracted. This paper summarizes the difficulties encountered and observations made during the driving and extraction of these piles.

By Lucien Weber

In the Shanghai area, the soil conditions are such that bearing piles have become an essential foundation part of the new highrise buildings. In order to reduce the settlements under the high working loads of about 2300 kN/pile, the Chinese building authorities require the pile tip to penetrate into the compact sand layer, situated at approx. 60-70 m depth. No H-piles have yet been tested under these conditions in Shanghai. This paper describes the driving of 8 H-bearing piles with 4 different shapes and with lengths varying from 45 to 75 m. Dynamic measurements are performed during driving and after a wait time of approx. 40 hours in order to assess the change in bearing capacity in function of time and in order to get an idea about the resistance distribution along the piles by using a stress wave analysis program (CAPWAP). One pile is equipped with channels between the flanges for executing verticality measurements with an inclinometer. However, this test has not yet been performed. One month after driving, two piles of 75 m length are statically loaded both in vertical and in horizontal directions.

Jan 1, 1987

By Keithe J. Merl, Brendan FitzPatrick, Gregg Piazza

Urban and industrial construction projects commonly involve interior work within buildings, warehouses and manufacturing facilities. Renovations of these existing structures must address both structural and geotechnical engineering challenges while also balancing the practicality of implementing solutions within site constraints including limited site access, overhead clearance restrictions, vibration tolerances and uninterrupted facility operations. This paper highlights two projects for an international shipping company where mezzanine level additions within active shipping facilities required construction of new foundations. Construction requirements included low vibration levels, as well as rapid and clean installation to limit impacts on the active shipping operations. The selected system also needed to adjust to both variable ground conditions and differing overhead clearances. This paper describes the installation, design and performance of Ductile Iron Piles used to meet the project challenges. The low vibration, driven pile system offered the ability to work within restricted overhead environments while successfully delivering working compression capacities ranging from 45 to 75 tons (41 to 68 tonnes) as well as lateral and tension resistance. The paper also presents the results of site-specific load testing (and pile capacity) for various termination criteria. INTRODUCTION Urban and industrial construction projects commonly involve interior work within buildings, warehouses and manufacturing facilities. Renovations of these existing structures must address both structural and geotechnical engineering challenges associated with the new construction. Foundation solutions must also balance the need to achieve design requirements with the practicality to be installed within the particular site constraints including limited site access, overhead clearance restrictions, vibration tolerances and uninterrupted facility operations.

Jan 1, 2019

By William Billiet

"The Dulles Silver Line Phase II is an 11.4 mile extension of the Washington Area Metro Transit Authority’s Silver line in northern Virginia. There are three miles of elevated guideway, which are supported on 188 large diameter mono-shafts founded within the Triassic Geologic Aged Culpeper Fault Basin. Three lateral load tests were performed on fully instrumented test shafts. The challenge in developing the load testing program was how to reproduce the effects of the extremely high design loads along the test shafts, considering the limitations of the load test equipment. Development, execution, and analysis of the lateral load test program is discussed.INTRODUCTIONPlans for Dulles Silver Line Phase II include two Aerial Guideway sections on elevated track, the Main Line and Yard Leads. The Aerial Guideways are supported on mono-shafts (single, largediameter drilled shafts) socketed into rock. Lateral loads are resisted primarily through the stiffness of the shaft and the geotechnical resistance of the rock socket. The monoshafts were designed in accordance with AASHTO LRFD 2014. Based on our preliminary analyses, the production mono shafts were expected to consist of 6.5, 7.5, and 8.5 foot diameter drilled shafts with rock socket lengths varying between 8 and 34 feet (averaging 14 feet). Table 1 summarizes the maximum service load combinations for each size production shaft along the aerial guideway alignment.GEOLOGYThe project is located within the Piedmont Province, a major physiographic province on the east coast of the USA extending from Alabama to Pennsylvania. Within the Piedmont, a number of Mesozoic basins formed in rift valleys. Dulles Airport is located in the Culpeper Basin, characterized by a relatively shallow siltstone rock surface compared to the adjacent areas underlain by Piedmont crystalline rocks. The geologic stratigraphy at the load test sites generally consist of residual soils and intermediate geo-material (IGM) overlying siltstone rock. IGM is a term used by Virginia Department of Transportation (VDOT) to describe residual material as it transitions between soil and rock. For the purposes of the load test, the siltstone rock is classified as fractured rock (RQD<50), and competent rock (RQD=50). Table 2 summarizes the stratigraphy encountered at each test site."

Jan 1, 2017

By Shahid Islam, Lucian Bogdan

"The maintenance of infrastructures has been of particular concern to the engineering community. As the world’s infrastructure expands and existing infrastructure ages, monitoring and evaluation of the structures have become more critical than ever. A large number of retaining walls, tie backs, slope stabilizations and piles are designed using pre-stressing steel. Many piles and drilled shafts are designed using reinforcing steel. There are few testing methods available to assess these tension and compressive forces. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYWIDAG-Systems International (DSI) has been involved in the development, testing and utilization of DYNA Force® sensors to measure the force in the anchors during construction and at any time during the lifetime of the structure. They can be used for bare, epoxy-coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the anchor. The sensor is robust and requires no maintenance. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. This paper describes its application in tie-back and anchor force monitoring of retaining walls and bridge abutment and compression forces in drilled shaft reinforcing steel where the data were collected manually, automated and remotely.INTRODUCTIONOur infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.The elasto-magnetic (EM) technology is a novel approach to monitor forces in steel elements. The DYNA Force sensor is built based on EM technology (See Fig. 1). It is composed of a primary coil and a secondary coil (sensing coil). By passing current through the primary coil, ferromagnetic material is magnetized. The sensing coil picks up induced electromotive force that is proportional to change rate of applied magnetic flux (Faraday's law) and relative permeability. As permeability of core changes, output voltage changes. The output voltage is calibrated to measure the force. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. The sensor has an embedded thermistor which allows for temperature compensation. Due to the diversity of the magnetic property of steel, calibration is done for each type of steel allowing the sensors to perform at their highest accuracy."

Jan 1, 2017

By Lucian Bogdan

On many occasions during construction and service life of the structure, it is crucial to know the load in post tensioning tendons and anchors. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive and the accuracy differs depending on the method used Dyna Force sensor uses the Elasto-magnetic technology (EM) and non destructive testing (NDT) to direct measure stress level in prestressed strands or bars installed on ground anchors or post tensioning tendons. Dyna Force sensor can be used to rapidly read the change in load during proof and performance tests and compare with the pressure gauge and during the life on the anchor to monitor existing lock-off load. It can be used also to determine the load along the bonded length of the anchor allowing the contractor to increase or decrease this length. The paper presents Dyna Force operating principle and some applications. In conclusion, the Elasto magnetic technology applied through Dyna Force is a new and easy to use approach to monitor anchor load during proof test and service life of the structure.

Jan 1, 2009

By Chris D. Thompson

In Southern Ontario, Canada, piles are frequently driven through competent clayey soils to obtain end bearing on extremely dense till or bedrock. One reason for this is the difficulty at assessing the adhesion of the clayey soils. This is illustrated by texts, such as the Canadian Foundation Engineering Manual, which is the standard of practice in Canada, that indicate that theoretical analysis of the adhesion values of such soils are unreliable. In this paper, the results of high strain dynamic testing have been used to estimate the shaft resistance of 11 closed end pipe piles driven in overconsolidated very stiff to hard clayey tills at four sites by means of the CAPWAP wave equation analysis. More than twenty-five years of experience with bearing capacity predictions by such means have developed considerable confidence in its accuracy. The results were found to correlate reasonably with the average Standard Penetration Resistances of the clays at the sites. There was a linear relationship between an adhesion of 64 kPa at 20 blows per 300 mm and 192 kPa at 60 blows per 300 mm. At one site, 6 piles were tested and found to have a wide range of Standard Penetration Resistance and estimated adhesion in the same stratum. While there was significant scatter of the results, piles would have been safe at design loads obtained from the relationships established by the analysis carried out for this paper after applying appropriate factors of safety.

Jan 1, 2002

By Jeremy Butkovich

Dynamic soil-structure interaction (DSSI) analyses are becoming more common in bridge designs, especially in seismically active areas. Because of its proximity to two active fault zones, the Evergreen Point west approach bridge replacement will be base isolated, and will be designed using DSSI. The project team completed two independent bridge designs to satisfy peer review requirements. The designs required substantial characterization of the soil dynamic behavior using both laboratory and in-situ testing. The analyses made use of earthquake time histories spectrally matched to conditional mean spectra. This led to reduced, and more realistic seismic demands on the structure, compared to conventional uniform hazard spectrum matching. The bridge analyses suggest that the preliminary bridge design is relatively conservative. This will allow the design team to potentially reduce shaft/column diameters and reinforcement. The design team estimates that the dynamic analysis design could represent a net savings of around $60 to $90 million compared to a conventional design.

By Greg Nutson, Jeremy Butkovich, Bill Perkins, Hollie Ellis, Paul Bott

"Dynamic soil-structure interaction (DSSI) analyses are becoming more common in bridge designs, especially in seismically active areas. Because of its proximity to two active fault zones, the Evergreen Point west approach bridge replacement will be base isolated, and will be designed using DSSI. The project team completed two independent bridge designs to satisfy peer review requirements. The designs required substantial characterization of the soil dynamic behavior using both laboratory and in-situ testing. The analyses made use of earthquake time histories spectrally matched to conditional mean spectra. This led to reduced, and more realistic seismic demands on the structure, compared to conventional uniform hazard spectrum matching. The bridge analyses suggest that the preliminary bridge design is relatively conservative. This will allow the design team to potentially reduce shaft/column diameters and reinforcement. The design team estimates that the dynamic analysis design could represent a net savings of around $60 to $90 million compared to a conventional design.INTRODUCTIONThe Evergreen Point Bridge conveys State Route (SR) 520 2.6 miles (4.2 kilometers [km]) from Seattle to Medina across Lake Washington. The bridge is located in a seismically active area, and the Washington State Department of Transportation (WSDOT) has determined that the western half of the 1960s-era bridge (the “west approach”) is vulnerable to earthquake damage. WSDOT has begun preliminary design to replace the west approach bridge.The west approach extends about 6,100 feet (1,900 meters [m]) east from Seattle’s Montlake neighborhood, over Union Bay and Foster Island, then into Lake Washington proper (Figure 1). Approximately 5,600 feet (1,700 m) of the replacement bridge would be constructed over water. Subsurface conditions along the bridge alignment consist of 5 to 80 feet (2 to 24 m) of very soft peat and clay, over very dense/hard sand and clay. Multiple pile supported columns support the existing bridge. The new bridge would be supported by 8- to 10- foot-diameter (2.4 to 3.0 m) drilled shafts that extend about 50 feet (15 m) into the underlying very dense/hard soil. To reduce seismic demands on the bridge superstructure, WSDOT has decided to incorporate a base-isolation system into the bridge design."

Jan 1, 2017

By Frank Rausche

Without doubt, driven piles are the most economical deep foundation element for a nearshore environment, providing for high bearing capacities and stiffness, quick installation times, assured quality by simple monitoring and inexpensive dynamic load testing during restrike testing. However, when the pile top elevation is several meters below water surface, questions often arise as to the most reliable and economical pile installation method. Frequently encountered, yet relatively expensive, solutions include driving inside a dewatered cofferdam, driving long piles that are later cut off below water surface, or using an underwater hammer. Arguably, the most economical solution is driving the piles with a follower or chaser. However, many foundation engineers shy away from this solution because of the uncertainty associated with the transfer of energy through the interface between follower and pile, the associated potential driveability problems and maybe the limited fatigue life of the follower. This paper will demonstrate how the driveability of a hammer-follower-pile-soil system should be analyzed prior to installation and how to model the pile-follower interface both for steel and concrete piles. As an example, results will be presented which were obtained for both steel pipe piles and precast concrete piles, driven by a single-acting diesel hammer through a steel follower for a pre-construction test pile program in Venice, Italy. While analysis of the steel pile-follower system was straightforward, for the concrete piles, the presence of a soft cushion material whose material properties changed continuously posed some difficulty. Pile Driving Analyzer® measurements and CAPWAP® analysis yielded not only realistic stresses and transferred energy values in the pile, but also reasonable model parameters for further use in a pure wave equation analysis. As a side note for clarity, the dynamic measurements and analysis results herein presented are based on the GRLWEAP and CAPWAP software. GRLWEAP is commonly used all around the world for the preparation of pile driving jobs. The program either yields a bearing graph that relates bearing capacity and pile stresses to blow count or set per blow or it predicts blow counts and pile stresses as a function of pile penetration. These results allow the contractor to estimate driving time and select an economical hammer and driving system for a safe and efficient installation. CAPWAP on the other hand is the analysis of choice once a pile has been installed and records of pile top force and velocity have been acquired during installation or during a restrike test. CAPWAP is a signal matching program which calculates for one particular impact (for example at the end of driving) the static and dynamic soil parameters. Its final results include the calculated resistance distribution, the complete stress history in the pile and also a simulated load set curve. The CAPWAP calculated dynamic soil parameters can also be used in a Refined GRLWEAP analysis to generate a calibrated bearing graph."

Jan 1, 2006

By Thomas Hyatt, Brandon Phetteplace, Camilo Alvarez

A test pile program was undertaken at a project site in Ain Sukhna, Egypt for an import/export oil jetty. Two 1219 mm diameter open ended steel pipe piles were evaluated at two separate test locations. Each test pile was dynamically tested during initial drive utilizing a Pile Driving Analyzer (PDA). Restrike testing was also performed to evaluate the time dependent soil setup. One static compression test and one static tension test was performed at each test location. A correlation of the static and dynamic load test results was established to develop a driving criteria for the piling across the two kilometer project. The constructability benefits of shorter piles will be discussed in more detail, given that the pile lengths were shortened by 9 to 10 meters on average. Lastly, the use of a four pile linear layout to perform both compression and tension tests will be covered. INTRODUCTION With the increased number of Very Large Crude Carriers (VLCC) & Ultra Large Crude Carriers (ULCC) being used to transport oil products around the world, companies and/or nations are presented with the challenge of transferring these products to and from the carriers in deep water scenarios, typically 15 to 20 meter depths, to accommodate the vessels draft. One option for loading/unloading the oil products from a VLCC or ULCC would be to transfer to/from smaller vessels several miles offshore, whereas the most economical option is to unload directly to a pipeline via a berth/jetty platform near shore. These berth platforms must be designed to withstand multiple loading scenarios while these carriers are moored and transferring their products. The use of Large Diameter Open Ended Pipes (LDOEP) piles are a common foundation choice for this offshore application. One of the drawbacks of LDOEP piles, especially across a large project site, is that there can be extreme variability in the pile driving behavior. This can be caused by either a change in soil conditions or the performance of the soil plug. Due to this variability, it is important to verify throughout the duration of the project that the piling is being installed to the correct criteria as established during the load test program. A well designed driven pile load test program, preferably with the combination of Static Load Testing (SLT) and Pile Driving Analysis (PDA), should develop a driving criteria that can allow the contractor and owner to monitor any change in driving behavior.

Jan 1, 2019

By Terrence M. Carroll, Chu E. Ho

"A pile installation and load testing program on driven tapered piles was undertaken at John F. Kennedy International Airport in New York City for the extension of the existing Terminal 4. As part of the program, dynamic testing by means of the Pile Driving Analyzer (PDA) was performed on several preliminary test piles as well as production piles. The results of the dynamic tests and subsequent static load tests were reviewed to develop an understanding of the pile-soil response of a tapered pile during driving and after setup. Pile setup occurred as a result of increase in shaft resistance with virtually no increase in toe resistance. More than 150 tons of additional capacity was gained after the setup time.The capacities measured during driving from the PDA are typically used as the basis for determining the pile driving set criteria, with the required initial driving capacities determined largely by the contractor’s experience. An improved appreciation of the setup phenomenon is required to better refine the driving criteria at the end of initial driving such that the required ultimate capacities can be obtained, with reasonable confidence, after a period of setup.This paper presents interpretation of pile-soil behavior from Case Pile Wave Analysis Program (CAPWAP) analyses and discusses the mechanism of increased capacity as a result of setup effects. Time-dependent capacity gain as a result of setup effects should be based on the extrapolation of the shaft resistance component rather than the total pile capacity as is commonly practiced. Prediction of pile performance using this approach was in good agreement with observed static and dynamic load test results.IntroductionTapered piles have been adopted for various projects at John F. Kennedy International Airport (JFKIA) since the late 1940’s. Initially timber piles were used exclusively, with steel Monotube piles being used from at least the 1980’s (Horvath and Trochalides, 2004). The steel Tapertube pile was developed in the mid-1990’s and has commonly been used in recent construction (Brusey and Yin, 2008). The Tapertube piles used for this project consisted of a 25 foot long tapered section that was 8 inches in diameter at the tip and 18 inches in diameter at the top. An 18 inch diameter straight pipe was welded above the tapered section."

Jan 1, 2015

By W. J. van Niekerk

Ballast Nedam is in Surinam constructing two bridges that will improve communications in the coastal region. The bridges will cross the Coppenam and Surinam rivers and will be founded on open-ended steel piles over 60 meters in length. The majority of piles are inclined and support prefabricated concrete girders forming the roadway. In most locations the stratum is consolidated cohesive layers extending to a depth in excess of 60 meters. For this reason, before pile driving operations commenced, it was decided that a number of test loads would be carried out determine the capacity of the piles. Loading tests were carried out on specially installed piles as well as on piles that would be used as working piles to support the structure. Working piles were dynamically tested using Pile Driving Analysis (PDA) equipment. This decision was based on the inclination of the piles, the cohesive nature of the soil and the increase of strength after the piles are driven. A good insight has been obtained into the real strength of the soil by comparing dynamic and static loading tests on vertical test piles. This made it possible to determine the required length of pile.

Jan 1, 2000

By Yingcai Han

The dynamic behavior of pile foundations is investigated in both theory and practice. The computation method for vibration of pile foundations and DYNAN computer program are introduced comprehensively. With a model of non-reflective boundary between the near field and far field, the Novak&apos;s method of soil-pile interaction is improved. The dynamic analysis and design of foundation for a reciprocation compressor with driver power 15,000 HP are described to illustrate the computation method of soil-pile interaction. Different design options for the piles are compared to limit the vibration of foundation and produce a safe, economic system. The design with 16 - 0.9 m piles is adopted rather than that with 25-0.5 m piles, since the larger damping is provided by the piles with larger diameter. Both field and laboratory tests were carried out to investigate the soil properties including down hole seismic tests to provide soil shear wave velocities at different depths. The method and procedure used in this study can be applied to the design of pile foundations for tall buildings, bridges and offshore platform with soil-pile interaction under seismic, blast, sea wave and other dynamic loads.

Jan 1, 2002

By Tsuda Wakaki, Naoki Takahashi, Natsuki Okuno, Hidenori Takahashi, Ikuo Towhata, Yoshiyuki Morikawa

"Deep mixing (DM) method has been increasingly employed as a countermeasure against subsoil liquefaction in recent years. Pile-type DM, however, is considered to have little effect as a liquefaction countermeasure, because the shear deformation of unimproved soil around the piles cannot be reduced. However, experimental results, which imply that shear deformation of unimproved soil around DM piles can be reduced, were reported. Furthermore, a new plane-arrangement of DM piles has been proposed to mitigate lateral flow induced by liquefaction. The DM piles in this arrangement confront the lateral flow in any direction, compared with the piles arranged in conventional pattern such as square and triangular arrangements. In this study, a series of dynamic centrifuge model tests was conducted to verify the lateral flow resistance of DM plies in the new arrangement. The results indicate that the DM plies can reduce the lateral flow of liquefied ground when the pile displacement and the pile head rotation are restricted. In addition, lateral load acting on DM pile from liquefied ground, which is required for design strength of the DM pile, was investigated.INTRODUCTIONDeep mixing (DM) method has been increasingly employed as a countermeasure against subsoil liquefaction in recent years. The solidified body formed by the deep mixing method is usually block or lattice shape, composed of solidified columns that overlap each other horizontally. Lattice-type solidification has been shown to be effective as a liquefaction countermeasure despite the presence of unimproved soil inside the lattice wall, because the shear deformation of the interior soil is restrained by the wall (Suzuki et al., 1989). On the other hand, it has been thought that pile-type DM cannot reduce shear deformation of unimproved soil around the piles, because the displacement of the pile is less restricted than that of the lattice wall. DM piles have been reported to have little effect as a liquefaction countermeasure, but to be superior in terms of construction cost and applicability around existing underground structures (Koga et al., 1986). However, there are experimental results implying that DM piles have reduced the shear deformation of unimproved soil and mitigated its liquefaction (Yasuda et al., 2003; Tanaka et al., 2003). Yamamoto et al. (2006) conducted dynamic analyses of ground improved with lattice- and pile-type DM. Their results showed that pile-type DM with an improvement ratio of more than 35% reduces excess pore water pressure generated by earthquakes. Furthermore, the new pile arrangement shown in Fig. 1(a) has been proposed to mitigate lateral flow induced by liquefaction. It was developed and has been verified using dynamic model testing in a 1 g field (Takahashi et al., 2010a; 2010b; 2013; Towhata et al., 2010, Morikawa et al., 2014). The DM piles in this configuration interrupt lateral flow in any direction, unlike those placed in square and triangular arrangements."

Jan 1, 2015

By Martina Balic

Dynamic properties of the drilled shaft foundations supporting Doremus Avenue Bridge were determined by forced vibration testing. The main objectives of the substructure testing at Doremus Avenue Bridge were: (1) site evaluation with respect to the dynamic soil properties, and, (2) shaft evaluation for the purpose of definition of their dynamic stiffness. The site characterization entailed crosshole testing for the purpose of evaluation of the shear modulus profile. The drilled shaft impedance evaluation was done through forced excitation using an electromagnetic shaker. The responses of the tested shaft, as well as the response of adjacent shafts, were measured for the purpose of evaluation of the shaft interaction. To gain a better insight into the shaft dynamics, one of the shafts was instrumented with five triaxial geophones distributed along the full length of the shaft. The scope and results of the site characterization, shaft impedance and shaft interaction evaluation are presented.

Jan 1, 2004

By Eiji Kojima

In this research, dynamic and static load tests were performed on permanent foundation piles which had a pile length of 30 m, 800 mm in outer diameter and 15 mm in wall thickness. In this site the dynamic horizontal load test on a smaller test pile, 12 m in length, 500 mm in outer diameter and 12 mm in wall thickness, was also carried out. The static horizontal load versus horizontal displacement derived from the dynamic load test conformed well to that measured in the conventional static horizontal load test of the pile with 800 mm diameter. Then an attempt was made to predict the horizontal load displacement of the pile with 800 mm diameter based on the results of the dynamic horizontal load test of the pile with smaller diameter of 500 mm.

Jan 1, 2006

By Kyle M. Rollins

To improve our understanding of lateral resistance of pile groups, a series of lateral load tests were performed on a full-scale pile group using both static and dynamic loads. The pile group consisted of nine 0.6 m-diameter steel pipe piles driven into clay. During the static tests, the load was cycled fifteen times to evaluate the drop in lateral resistance that would occur due to repeated loading and the formation of a gap. The peak load typically decreased by about 15% from the initial cycle to the last cycle. The load carried by each pile was also measured and there was a significant drop in resistance for the piles in the trailing row relative to the leading row. The dynamic force was applied using the Statnamic loading system which produced a lateral force of 3500 kN (787 kips) in about 0.1 seconds. In two cases, dynamic loads were applied following application of 15 static load cycles. In these cases, the dynamic lateral resistance was about the same as the static resistance, likely due to gaps around the pile. In three other cases, the dynamic force was applied prior to the cyclic loading. In these cases, the dynamic resistance was 30 to 60% higher than the static resistance. Simplified analyses suggest that the difference in resistance could be attributed to damping produced by the soil surrounding the piles during the virgin loading.

Jan 1, 2002

By Bosco Poon, Kim Chan, Luis Raúl Castañeda, Geoff McKay

"Driven steel tubular piles of up to 2 m diameter have been used to support abutments and piers of a bridge over Nambucca River and floodplain. The bridge was designed by Arup-Aurecon Design Joint Venture (Lead Designers) with GHD leading the geotechnical design assessment in conjunction with Acciona Ferrovial Joint Venture (AFJV – Principal Contractor). Piles were to be driven through alluvium and founded on foliated Phyllite bedrock. The large diameter piles posed significant challenges on bearing capacity assessment and pile acceptance criteria, especially for anisotropic rock strength. Prior to pile driving, boreholes were drilled at each pile location, accompanied with a suite of rock index and UCS testing. AFJV and GHD oversaw geotechnical construction verification. All production piles were monitored with a Pile-Driving-Analyser to manage driving stresses and pile termination. Wave matching CAPWAP analyses were performed on 40% of the piles at the end-ofdrive, or restrike, to satisfy specification requirements and limit over-driving. This paper presents discussions on the design and construction of the driven piles with findings from the extensive dynamic pile data obtained. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft frictions fs of the soil / rock materials, as well as the end bearing fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the m obilised fb, and the relationship between rock strength and the mobilised fs are outlined.INTRODUCTIONThe Bridge over Nambucca River consists of a single bridge structure, comprising single substructures and separate superstructures. The 850 m long bridge facilitates the crossing of the Northbound and Southbound carriageways of the Pacific Highway Upgrade over Nambucca River, with central median barriers, separated by a horizontal clearance of 50 mm. The bridge is required to span over the Nambucca River, which is a navigational channel, and over the adjacent floodplains, including two local access roads and the existing Pacific Highway. The bridge superstructure consists of 21 simply supported spans, each comprises four 2.25 m deep precast post-tensioned U-Girders, with two girders across the width of each carriageway. The spans of girders vary from eleven spans of 39.5m and ten spans of 41.5 m. The floodplain section of the bridge was founded on up to 2m diameter steel tubular piles, designed to be driven through alluvial sediments and weak rock to nominal refusal on sound rock. Dynamic load testing using wave matching CAPWAP (CAse Pile Wave Analysis Program) analyses in conjunction with PDA (Pile Driving Analyser) were used to verify the pile integrity and mobilised capacity. This paper discusses geotechnical aspects associated with design and construction of driven piles. The methodology developed for construction to verify pile capacity and to meet acceptance criteria is outlined. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft friction, fs of the soil / rock materials, as well as the end bearing, fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the mobilised fb, and the relationship between rock strength and the mobilised fs are outlined."

Jan 1, 1900

By Garland Likins

High strain PDA testing has become common for verification of capacity of both driven and bored piles. It is equally applicable to Augered-Cast-in-Place (ACIP) Piles. It also evaluates other aspects of the installation such as integrity. The benefit of high strain dynamic test results for the relatively low cost of the tests compared to conventional static testing has resulted in widespread use. The method is described and specific procedures for testing ACIP piles are outlined. Example results demonstrate the application.

Jan 1, 2000