Search Documents

By S. Ali Bastani, Ashley Varni

Design acceleration response spectra (ARS) are directly correlated with dynamic forces and estimated dynamic bridge displacements, which make them a critical aspect of dynamic bridge design. Nonlinear site response analyses are performed for a 1,400-linear-foot bridge site with a SC soil profile at the sides and a SF soil profile in the middle to evaluate the soil profile effects on the bridge analyses. One-dimensional seismic response analysis is commonly performed for site-specific response analysis. SHAKE or similar one-dimensional total-stress equivalent-linear approaches have been used since the 1970s. However, the equivalent linear method has deficiencies when the subsurface soils are susceptible to strain softening. Therefore, various assumptions are made when using the equivalent linear method by practitioners to estimate the SF soil profile site response. With recent advancements in constitutive models, effective stress models have become more popular. Although the effective stress models are generally more complicated and require additional input parameters, they shed further light on the liquefaction mechanism and its effect on the surface ARS. An equivalent-linear one-dimensional seismic response analysis and a non-linear effective-stress seismic response analysis, using DEEPSOIL, were performed to evaluate the ground surface ARS for a proposed bridge site in Orange County. The soil shear strengths were estimated based on cone penetration test results using empirical relationships. The shear modulus degradations (backbone curves) of soil layers were adjusted to match the estimated soil strength at failure. The ARS curves developed from each method were compared to determine the most suitable method for estimating a site-specific design ARS curve for a liquefiable site. Considering that the bridge abutments and the outer bents are founded in bedrock, while the middle bents are founded in liquefiable soils, ARS curves were created for each subsurface condition. Taking into account limitations of the structural analysis software, recommendations were made to combine the multiple ARS curves into a single ARS curve for the structural bridge design.

Jan 1, 2018

By Charles L. Guild

I will add a few facts about the use and development of the Osterberg Test Load Cell and my association with Jorj. I first met Jorj in 1965 when the Guild Construction Co. drove 12" diameter cast-in-place shell piles for him at the Marquette Cement Co. in Nashville, Tennessee. When I met Jorj at the DFI Trustee's meeting in 1985 at Longboat Key, Florida, he showed me a sketch of his idea about using a test cell at the bottom of a caisson to test the end bearing and side friction on a caisson. He had made a successful trial test in Case International's equipment yard and wondered whether a similar device could be made for a driven pile. At first I was skeptical that it could be done but after thinking about it overnight I told him I felt it was feasible and we would do some work on it. At that time, there was a large bridge job going out for bid in Rhode Island using 14" square prestressed concrete piles'. Based on a record of the Guild Construction Co. Inc. driving over 3,000,000 feet of piling on work for the State of R.I., we felt we would have an excellent chance to be allowed to use them so we designed, detailed and fabricated three for 14" square prestressed concrete piles. As things worked out, we did not test them on this job and have not to date.

Jan 1, 1989

By Aditi Sharma, Sumanta Haldar

Scouring of soil is the major concern forthe various hydraulic structures built in the flowing rivers since scouring impacts the bearing capacity of foundations. Hence, consideration of scouring in the design of foundations for hydraulic structures is crucial. Pile groups in bridges are subjected to combined vertical and horizontal loading due to self-weight, live loads, vehicular impacts, wind load, earth pressure, and current. Hence, an assessment of the combined bearing capacity of pile groups subjected to scour is essential for the safety of the structure. This paper aims to analyze the bearing capacity of pile group supporting the bridge under combined loading i.e., Vertical (V) and Horizontal (H) loading subjected to local scour. Three-dimensional finite element model (3D-FEM) of a 3 x 3 pile group embedded in homogeneous sandy soil is established in Abaqus (2018). Mohr-Coulomb plasticity model is used for the soil domain. The pile group is modelled as linear elastic. Finally, V-H yield envelopes are obtained with and without scour. The potential impact of different parameters, such as angle of attack, flow velocity, depth of flow, and different pile length-to-diameter ratios (L/D) and spacing-to-diameter ratios (S/D) of pile group on V-H yield envelopes is studied.

Sep 1, 2022

By Klaus Pöllath

This paper describes mitigating measures and the design of compensation grouting which will be executed from deep shafts of the Amsterdam North/South Metro line project. Due to the specific conditions for TBM-tunnelling in Amsterdam (historical buildings on pile foundations near the tunnel and soft soils with high groundwater levels) tunnel construction necessitates mitigating measures, such as compensation grouting or soil freezing. Züblin developed a special shaft construction method for critical distances to buildings. For the compensation grouting Züblin developed a new software tool, called SOFIA, which controls and visualizes and thus optimizes the entire injection process. This tool significantly increases the efficiency of the injection works while reducing the geotechnical risks.

Jan 1, 2006

By George Machan

Bitumen coatings have been successfully used to significantly reduce downdrag on piles. Thicker coatings of "soft" bitumens can accommodate downdrag so well that very little downdrag load is transferred to the pile. Many of the case histories describe better than 80 percent downdrag load reduction. Bitumen coatings have been used on several projects in Oregon. On the Mocks Bottom Bridge project (see Reference 1), experimentation and instrumentation confirmed the viability of bitumen coatings and provided insights for design and construction. Subsequent bridge projects have used this information and have raised issues to be resolved.

Jan 1, 1989

By A. Fisher

The use of thermal integrity testing to verify the quality of deep foundations has increased significantly in the UK and other world markets over the last 5 years. The introduction of distributed fibre optic sensing to this field has broadened the range of applications in which it can be deployed and the types of foundations which can be tested. This paper presents how fibre optic sensing technology can be successfully deployed in the construction environment the range of foundation techniques to which it can be applied. Alongside developments in the practical aspects of thermal testing, progress has been made in establishing assessment criteria which can be used to evaluate the results. This paper presents recent examples of comparative studies on foundations which include both thermal integrity testing, cross hole sonic logging and intrusive coring. The use of distributed strain measurement during pile load testing presents an alternative means to verify the assessment criteria used for integrity testing. This new approach can achieve comparable results to foundation exhumation or intrusive investigation and at a fraction of the cost. This paper presents the findings of several such studies, highlighting the benefits and opportunities for future improvement of the method.

Oct 1, 2022

By Jay L. Hodkinson

Replacement of an aging twin span river crossing in Vermont required a temporary bridge to accommodate traffic during construction. Soils beneath the temporary approach embankment consisted of very soft organic clayey silt underlain by interbedded, loose alluvial fine sand and silt/clayey silt. Reinforcement was required for the southern temporary approach embankment to limit settlement and to increase global stability factors of safety. A ground improvement design was developed using Rammed Aggregate Pier® reinforcement and was included in the contract documents as an FHWA Category II Experimental Feature. Instrumentation intended to document the performance of the supported embankment was installed. Piers were then constructed and monitoring commenced as embankment and bridge construction occurred. Weekly instrumentation data reports indicated continuing excess pore water pressure, settlement, and lateral deformation of the subgrade soils as the embankment and temporary bridge abutment was constructed. In response to the unanticipated monitoring results, further investigation indicated that significant deviations from the conditions and basis upon which the ground support design was developed were made during construction. This paper discusses these deviations and their specific impacts to embankment support performance, how these deviations occurred, the role that the ground support system played in maintaining global stability, measures taken to limit further detrimental impacts to the embankment, and provides recommendations for contract document preparation and construction oversight to prevent similar situations from occurring on future projects.

Jan 1, 2011

By Masanoub R. Fujioka

A brief discussion of the methodologies involved in dewatering practices, particularly as used in Hawaii in coralline formations. A description of early dewatering practices includes a number of case histories; later dewatering practices also are detailed with case histories. There were disasters and some successes. Grouting generally was not successful. Deep wells are technically feasible and generally the economical solution to deep basement construction.

Jan 1, 1986

By Antonio Zechini, Giuseppe Iorio, Massimo Grisolia

"The new C Line of the Rome Metro runs northwest to southeast across the city center, with 30 new stations and a total length of more than 15.5 mi (25 km). Due to the presence of a dense urban environment, the selected solution for the construction of the stations consists of a cutand- cover excavation, which is retained by multipropped diaphragm walls to minimize settlement and prevent damage to the nearby structures. The bottom of the excavation of the underground stations are about 82 ft to 98 ft (25 m to 30 m) below ground surface, and about 66 ft to 82 ft (20 m to 25 m) below the groundwater table. To ensure dry conditions and to prevent hydraulic base heave instability, deep well systems were designed and used to lower groundwater level and piezometric head during excavation. The dewatering field tests showed how the local stratigraphy strongly affects the dewatering efficiency. Finite element modeling (FEM) of steady state filtration were used to compare the soil permeability with Lefranc in-situ test results and to verify the efficiency of the grouted plugs. The geological sequence along the new C Line consists of a very heterogeneously layered deposit. The base deposit of stiff overconsolidated clay (“APL,” Pliocene age) is overlain by fluvio-palustrine very dense sandy gravels (“SG,” Pleistocene age), which are then overlain by medium stiff clayey silts or dense sandy silts (“AR” or “ST,” Paleotevere units). These deposits are overlain by covered by pyroclastic volcanic soils, tuff, silty sand and sandy silt (Middle to Upper Pleistocene) deriving from the Colli Albani apparatus. A layer of made ground (“R”) of varying thickness covers the stratigraphic sequence and the natural soil profile everywhere.The local hydrogeological framework is very complex and characterized by a double groundwater system. The upper main aquifer is mainly represented by the “pozzolane sequences” (“PR/PN”), while the lower aquifer consists of a deposit of sandy gravel (“SG,” Pleistocene), which is underlain by marine claystone bedrock (“APL,” Pliocene). The pyroclastic deposits (e.g., pozzolane, lithoid and pseudolithoid tuff and clayely tuff) show large variations in permeability due to porosity, compaction processes, sealing and secondary fracturing. Permeability values for each soil type were determined using Lefranc tests at variable head and using pumping tests. The Lefranc tests indicated a wide range of permeability."

Jan 1, 2017

Jan 1, 1992

Jan 1, 1987

By Alice Arana, David M. Cacoilo, Joel L. Volterra

"To make space for the new South Ferry Station in lower Manhattan, engineers and contractors carved out a new tunnel beneath three operating subway tunnels and tangentially to yet another tunnel. Creating the space required the design and construction of complex temporary excavation support and underpinning systems and the design and installation of real-time monitoring systems. Construction for the new station and tunnel was mainly cut-and cover in a mixed-face area of soil and rock approximately 2,000 linear ft long, 60 ft wide and up to 70 ft deep. Close coordination between the design/build team and the project owner, the Metropolitan Transportation Authority (MTA), was critical.With the construction of this $400 million project, the MTA and New York City Transit (NYCT) are correcting the numerous physical and operational deficiencies of the existing station and improving the lives of millions of commuters. Built in 1905, the original South Ferry Station is on the IRT Broadway–Seventh Avenue Line of the New York City Subway and is the southern terminal of the #1 subway service, which forms a loop to return uptown. The station has a sharply curved single platform on the outside of the outer track of a two track loop. This platform is short and does not allow the rear five cars of a normal 10-car subway train to load or unload. In addition, once the train stops at the station, commuters wait while retractable floor grates bridge the gap created between the platform and the subway car doors, and then they have only one exit from the station. Spray nozzles keep the tracks lubricated to reduce the train wheels’ friction caused by the tight curve. The sharp curvature of the loop and the inability to use half of the subway car doors slow train operation. With the new ADA-accessible station, 10-car trains will be able to open all doors, and additional entrances, escalators and elevators will greatly reduce travel times."

Jan 1, 2008

By Bernard H. Hertlein

"When the Deep Foundations Institute (DFI) was founded, quality assurance and quality control (QA/QC) of foundation construction was rudimentary. Nondestructive testing (NDT) was a nascent technology, known to very few people, and very limited in its capabilities and applications. In the four decades since the DFI became a reality, NDT researchers and practitioners have taken advantage of technological advances to improve those existing testing and analysis techniques, and to create new ones that have all contributed to the engineering body of knowledge. This has enabled contractors to improve the quality and reliability of their products, and engineers to design more efficient foundations.Through its regular series of seminars, publications and annual meetings, the DFI has been vitally important in educating the deep foundations industry about the capabilities and benefits of NDT methods. In turn, NDT results have helped the industry identify problems in deep foundation construction, determine the causes of those problems, and improve design constructability and construction practices to increase the quality, reliability and efficiency of all types of deep foundations. This presentation reviews the evolution of several important NDT methods, and the contributions that they have made to foundation quality.THE BEGINNINGSThe Deep Foundations Institute (DFI) was incorporated in 1976 in the State of New Jersey as a 501(c)(6) non-profit association. The DFI is a consensus organization of Contractors, Engineers, Owners and Suppliers involved with the design and construction of all types of deep foundations. The purpose of the DFI was and still is to improve the planning, design and construction of deep foundations by educating all those involved, sharing best practices, and promoting the adoption of new technologies that improve quality, productivity or safety.This is well expressed in the current DFI Mission Statement: To bring together multi-disciplined individuals and organizations to find common ground and create a shared vision and a consensus voice for continual advancement in the deep foundations industry.At the time the DFI was born, nondestructive testing for verifying the quality and integrity of deep foundations was in its infancy, its growth constrained by the technology, or lack thereof. Some visionary engineers of the time understood the physics of the potential methods, and therefore the possible capabilities, but were frustrated by the lack of technology to work with. Electronic equipment was mostly analog, and the few digital data acquisition systems that were available had such slow sampling rates that they were incapable of recording rapid event sequences or short duration events such as those used in modern integrity tests. For example, Jean Paquet, a leading research engineer at the French National Construction Institute, (Centre Experimentale de Recherche et d’Etudes du Batiment et des Travaux Publics, or CEBTP) patented the frequency-based analysis procedure for the Transient Dynamic Response (TDR) method, aka Sonic Mobility or Impulse Response, in 1974, but it was not until 1977 that analog data acquisition systems became fast enough to turn his theory into a reality."

Jan 1, 2017

By Derrick Dasenbrock

Two DFI committees independently organized two complimentary panel sessions for the recent American Society of Civil Engineers' (ASCE) Geo- Risk 2023 "Advances in Theory and Innovation in Practice" Conference in Arlington, Virginia, July 23-26. The Geo- Institute (GI) specialty conference welcomed more than 200 professionals and students interested in risk from around the world to the Washington, D.C., area for three full days of plenary keynote lectures, papers and no-paper sessions. The GI Risk Assessment and Management Technical Committee organized the event, which is the third in a series planned on a 6-year cycle. The previous two events were in 2011 in Atlanta and 2017 in Denver.

Sep 1, 2023

By Rob van Dorp

"AbstractThe Monitoring & Instrumentation Committee (MIC) of DFI Europe has the objective to support DFI members in concern of risk management of geotechnical matters, where monitoring and instrumentation have added value.Work of the CommitteeA study by the committee showed that there are already several existing (national) guidelines. They all have their strengths and limitations and their focus may vary a little per country due to local regulations and typical local building activities, but the main question remains what added value another new guideline would have. More likely it would add to the confusion instead of providing overview.Companies with larger experience in geotechnical monitoring (often larger consultancy firm, contractors or clients) are already quite familiar with its benefits do not really need a new guideline in how to design and effectively apply sophisticated geotechnical monitoring systems for special projects.Therefore the aim of the MIC is to focus a little more towards smaller organizations - that are less familiar with monitoring and instrumentation - and the more ‘regular’ type of project that they are mainly involved in. The MIC wants to create a tool which helps them to create risk awareness, to understand the benefits of geotechnical monitoring and to provide them information about how and where to find the right partners and equipment to setup and apply appropriate monitoring systems for their projects.Monitoring and instrumentation benefits are for example:• Risk control during construction stage;• Costs reduction in design and construction (taken limitation of geotechnical aspects into account).• Prevent of unnecessary delays in construction work• Increasing general awareness of geotechnical risks and possibilities of monitoring.The cost of monitoring compared to the cost of failure and/or the savings that can be achieved play a role in the work of the committee. DFI members benefit from the shared knowledge by the MIC on monitoring and instrumentation within their process of risk management."

Jan 1, 2014

By Jim Bruce, Peggy Hagerty Duffy, Mary Ellen Large, Allen Cadden

"Over the past 40 years, Deep Foundations Institute (DFI) has executed its mission “to bring together multi-disciplined individuals and organizations to find common ground and create a shared vision and consensus voice for continual advancement in the deep foundations industry”. Like DFI, micropile technology began a significant growth path in the mid-1980s. This paper highlights how DFI’s mission was executed in the deployment and expansion of micropile technology.INTRODUCTIONMicropiles are small diameter foundation elements constructed using specialty drilling and grouting methods. Micropiles have evolved since their introduction into the North American market in the 1970s from being lightly loaded (less than 30 kips) elements used primarily for remedial applications, to today’s high-capacity, often hybridized foundation systems, for both remedial and new-build projects. Micropiles now occupy a substantial market segment in North America.For 40 years, DFI has aimed to be the forum for discussion of all issues related to deep foundations design and construction. DFI now supports 21 technical committees and working groups on all deep foundations technologies and has expanded to include regional chapters in Europe, India and the Middle East.Several key steps are required for the successful execution of DFI’s mission, including identifying a need, engaging dedicated and knowledgeable people, developing effective vehicles and resources for information sharing, cultivating stakeholder contributions and advancements, stimulating influence/impact on deep foundations market, and expanding approaches to continue progress. Pile drivers in New York City (the original organizers of DFI) positively affected their market using these same steps: they recognized a specific need, gathered the people who could affect change, convened a discussion forum (which is common today, but was innovative at the time), defined tasks to address the issues, and influenced their market by improving means, methods and owner perception of their services. These forward thinking, proactive members created a mechanism for communication among all related parties that would advance the profession by improving safety, quality and value of pile driving construction.Micropile technology has evolved in the United States and around the world for the past four decades. The accumulated efforts of DFI and other, similar organizations such as The International Association of Foundation Drilling (ADSC) have contributed to this evolution. The advancement of the micropile industry – and consequently the micropile market – has been intimately tied to the execution of the mission of DFI."

Jan 1, 2017

With respect to liability damages, claims and costs thereof relating to or ansmg out of contamination, special or non-special wastes, hazardous wastes or pollution in connection with the performance of this subcontract: It is understood that the subcontractor's work and responsibility wholly exclude any requirement to handle such contaminants or to otherwise be responsible for such contaminants, and Subcontractor shall not be nor be considered to be a generator of such contaminants. Contractor shall indemnify, defend and save harmless Subcontractor and its sureties, from and against all liability, damages, claims and costs relating to or arising out of contamination, special or non-special wastes, hazardous wastes

By George Onorato, Giovanni Bonita

Deep soil mixing (DSM) has become a widely used ground improvement technique globally, producing soil-cementitious materials for various complex civil and environmental applications. In the field, the soil-cement materials form under confining stress conditions, which are often overlooked, as most wet grab specimens are cured and tested under ambient atmospheric conditions. This oversight has led to an underestimation of the engineering and mechanical properties of the soil-cement mixed material. With support from the DFI Technical Committee Project Fund, the authors initiated a multi-phased comprehensive research study in collaboration with industry experts to gain a fundamental understanding of these effects. This study investigates the curing conditions to which in-situ materials are exposed and how these conditions influence the strength of deep mixed materials. The findings reveal that the curing conditions for in-situ materials, including applied stresses and temperatures, significantly differ from those under which typical quality control specimens are cured. Neglecting these conditions can lead to a substantial underestimation of in-situ material strength. The data compiled for this study encompass strength and temperature data obtained from specially designed laboratory bench tests, field-conducted modified oedometer tests, in-situ instrumentation tests within deep mixed columns, and a review of independent coring data from deep mixed projects across North America. Analysis of these collective studies reveals a correlation between curing stress and unconfined compressive strength (UCS). The rate of strength gains follows a linear pattern and is influenced by the soil type being treated. Fine-grain soils, in particular, exhibit a higher rate of strength gain when subjected to in-situ curing stress (with depth) compared to granular soils. The paper delves into fundamental processes such as drainage, consolidation, and interparticle behaviors of deep mixed materials from their fresh state until the treated column has cured. It also presents empirical and analytical methods to correct in-situ strength measurements to account for the effects of curing stresses.

Oct 7, 2024

Jan 1, 1988

By DFI DFI

An Online Conference