Search Documents

By J. Gniel, L. King, C. Gaudin, C. O’Loughlin

"This paper presents some recent advancements in centrifuge modelling, which enable the installation of displacement piles to be performed in-flight while measuring ground responses. Details and results are provided from a series of experiments where 21 full-displacement piles were installed into a sample of consolidated kaolin clay at 40g. The piles were pushed into the sample at a constant rate of penetration, with installation reaction loads and pore pressures measured. Insight into the installation effects of the full-displacement piles was obtained by undertaking in-situ testing pre- and postinstallation of piles. The findings show that centrifuge testing has the potential to play an important role in furthering the current understanding of displacement pile behaviour and installation effects.INTRODUCTIONDisplacement piles and displacement ground improvement columns cause soil to undergo significant distortion and shearing during installation, which alters the soil properties. It is essential to consider these changes in soil properties to estimate the behaviour of pile foundations with higher degree of accuracy. However, the installation effects of displacement piles are widely considered as one of the most difficult geotechnical mechanisms to model, both analytically and numerically, and experimental data is needed to advance the current state of knowledge.Theories, analytical and semi-analytical, have been developed to describe the displacement pile installation process. Randolph et al. (1979) applied the cylindrical Cavity Expansion Method (CEM) to model the installation of a displacement pile in a fine grained cohesive soil. However, cylindrical CEM only considers the field variables in radial coordinates, and hence the soil-pile interface can only be modelled as a frictionless material. Baligh (1985) introduced the Strain Path Method (SPM), which assumes soil flows around the tip of a displacement pile. SPM was shown to model the stress and strain fields, particularly within close proximity to the pile, more accurately compared to the cylindrical CEM. While these methods account for the installation effects of a displacement pile and can be used to estimate a resulting ultimate bearing capacity, they are unable to describe the load-settlement behaviour of such piles. With the added complexity of group effects, existing analytical methods do not provide a means to accurately calculate the ground response to the installation of a group of displacement piles in a cohesive soil.The advancement of computational power, numerical techniques and constitutive models has improved the accuracy of numerical analysis, particularly in regard to modelling pile installation. However, even with advanced techniques, Finite Element Method (FEM) suffers a number of disadvantages due to the large deformations, which results in mesh distortion and tangling. Mesh-free methods such as Discrete Element Method (DEM), Smoothed Particle Hydrodynamics (SPH) and Material Point Method (MPM) are the next generation of computational techniques that are able to deal with large deformation problems. However, these advanced techniques are computationally expensive, complex and yet to be incorporated into commercial packages. Such methods are considered to still be in the development stage and are yet to provide a complete solution to pile installation problems."

Jan 1, 1900

By Shinji Sassa, Naoki Takahashi, Eiji Kohama, Wakaki Tsuda, Hidenori Takahashi, Ikuo Towhata, Yoshiyuki Morikawa

"Abstract Deep mixing method has been employed increasingly in recent years as a countermeasure against subsoil liquefaction. Column-type solidification, however, has been thought to have little effect as a liquefaction countermeasure, because the shear deformation of unimproved soil between the columns cannot be reduced. In recent years, experimental results have been reported that imply that solidified columns can reduce the shear deformation of unimproved soil around them. A new arrangement has been proposed to mitigate lateral flow induced by liquefaction. In this study, a series of dynamic centrifuge model tests was conducted to verify the lateral flow resistance of stabilized columns. The results indicate that stabilized columns can reduce the lateral flow of liquefied ground if the column displacement and the column head rotation are restricted. This paper concludes that it is important to restrict the displacement and the rotation of the column head by surface improvement to mitigate the lateral flow of liquefied ground.INTRODUCTIONDeep mixing method has been employed increasingly in recent years as a countermeasure against subsoil liquefaction. The solidified body formed by the deep mixing method is usually block or lattice shape, composed of solidified columns that overlap each other horizontally. Lattice-type solidification has been shown to be effective as a liquefaction countermeasure despite the presence of unimproved soil inside the lattice wall, because the shear deformation of the interior soil is restrained by the wall (Suzuki et al., 1989). On the other hand, it has been thought that column-type solidification cannot reduce shear deformation of unimproved soil around columns, because the displacement of a solidified column is less restricted than that of a lattice wall. Column-type solidification has been reported to have little effect as a liquefaction countermeasure, but to be superior in terms of construction cost and applicability around existing underground structures (Koga et al., 1986). However, there are experimental results implying that solidified columns have reduced the shear deformation of unimproved soil and mitigated its liquefaction (Yasuda et al., 2003; Tanaka et al., 2003). Yamamoto et al. (2006) conducted dynamic analyses of ground improved with lattice- and column-type solidification. Their results showed that column-type solidification with an improvement ratio of more than 35% reduces excess pore water pressure generated by earthquakes. Furthermore, the new column arrangement shown in Figure 1(a) has been proposed to mitigate lateral flow induced by liquefaction. It was developed and has been verified using dynamic model testing in a 1 g field (Takahashi et al., 2010a; 2010b; 2013; Towhata et al., 2010). The stabilized columns in this configuration interrupt lateral flow in any direction, unlike those placed in square and triangular arrangements."

Jan 1, 2014

By Stuart Coutts

"This paper presents an overview of the author’s experience related to the assessment of the base capacity of straight shafted and enlarged-base bored piles in sand. A design approach based on CPT qc is described which has been calibrated using a database of load tests. The importance of correct installation techniques with instrumentation are illustrated and a discussion is presented on the current use of high strain dynamic testing to validate compliance with design. An example of a recent project with high quality instrumented load test data illustrates the close match to the proposed best practice approach and also highlights the importance for consideration of the effects of stress relief for deep foundations installed in deep excavations.1 INTRODUCTIONContinuous Flight Auger (CFA) piles are the bored foundation pile of choice for sand deposits across Australia. The evolution of the determination of the base resistance of CFA piles has been shaped by available investigative techniques, calculation methods, and calibration of designs with laboratory and field testing. The Cone Penetration Test (CPT) has been widely used in Western Australia (WA) where the test has been commercially available via multiple contractors for more than 25 years. On the East coast, the adoption of CPT testing has been slower with a transition from traditional Standard Penetration Testing (SPT) still occurring. Dynamic pile load tests are often used to derive parameters. The influence of pile installation on performance is commonly misunderstood and is an important element on any discussion of pile capacity for CFA pile types. The interface between the base of the constructed pile and the in-situ soil has an influence on capacity such that a poorly constructed pile base will have limited (if any) contribution to pile performance within the normal working range, generally within a 10 mm movement. The research presented in this paper pertains to CFA piles (no drilling fluids) and enlarged base piles constructed using CFA techniques under drilling fluids such that clean pile/base interface is targeted. Developments in modern piling equipment and instrumentation allow the pressure and volume of delivered concrete/grout to piles to be accurately monitored at various stages of installation such that repeatable ‘best practice’ can be achieved. The changes in soil conditions that occur due to the disturbance of the install technique are also important.Although the results of this research are likely applicable to bored piles, the interface between the pile and in-situ soil (shaft and base) need to be considered for various installation techniques. The effects of stress relaxation (due to removal of soil above pile base and adjacent shaft), time to concreting, and the zone of disturbed soil around the pile shaft are paramount.2 INSTALLATION CONSIDERATIONS The pile mix (concrete/grout) and interface with the in-situ soil are also an important consideration. For example, coarse grained, poorly graded, dry, clean sand will be partially permeated by most pile mixes; such that the influenced soil will be enhanced and in instances the overall effective pile dimensions increased. Permeation of the disturbed zone of a pile or anchor shaft along with scale effects (Lehane 2009) can have significant effect on shaft capacity and shaft frictions significantly exceeding expected are not uncommon based on ‘theoretical’ dimensions. Advancements in mix technology and mix techniques also have a large influence on the pile/soil interface. The ability of the piling rig and augers to excavate a plumb and gauge hole can also have a large influence on the zone of soil disturbed adjacent the constructed pile with a resulting influence on capacity."

Jan 1, 1900

By Philip Derbyshire, Dale J. Scheffler

"Continuous Flight Auger (CFA) piling is a variation of Augered Cast-In-Place (ACIP) or augercast piling. In both cases a continuous auger with a hollow stem is used to drill a hole and a pile is formed by injection of cementitious material through the hollow stem as the auger is withdrawn. CFA differs from conventional American ACIP by the use of concrete rather than grout to form the pile, and by the type of equipment used to advance the auger into the ground and withdraw it. CFA installation uses a European style rig (i.e. fixed mast and rotary system) which can produce greater crowd and usually has a larger rotator or drill motor than the standard augercast setup. A standard augercast setup will consist of a lattice-boom crane and a set of leads to house the drill motor and auger. The auger size will range up to 24 inches (610mm). With CFA rigs larger diameter piles can be constructed, 24 to 36 in dia. (610mm to 915mm) are common and the technique has been applied with diameters up to 48-inch (1220mm). CFA makes use of sophisticated computer controlled monitoring systems, which have more recently been introduced for conventional ACIP piling. Developments in CFA have taken place over the last 25 years in Europe and particularly in the UK, but are relatively new in the USA. One application is in the construction of secant (overlapping) piled retaining walls. D.J. Scheffler Inc. recognized the potential of the CFA system following visits to the UK and has introduced its use into California for both secant piling and other applications.BACKGROUNDThe high price of real estate in many of the favored areas of California has increasingly led owners to want to build basements under their houses to increase the floor space available on a lot. Many of these areas are by the coast where the ground conditions are predominately granular and the water table is high. Conventional shoring and dewatering systems have often caused problems with adjoining properties. Clearly tangent walls are not suitable in these conditions because of leakage and loss of ground. The secant pile system, using CFA techniques, has proved very effective at overcoming the problems experienced by other methods. Other applications for CFA secant walls have included use for an emergency job on a highway following erosion caused by unusually heavy rainfall.METHODThe concept of secanting piles, whereby primary(female) piles are installed first and then secondary (male) piles are cut into the primary piles is not new. The method has been known for more than 30 years. Originally ‘Benoto’ grabbing rigs, developed in Japan, were used together with sectionalized double skinned casing and oscillators.This early method was slow, although very effective. More recently high torque rotary machines have been used. Contractors in the UK have increasingly used CFA techniques to further improve productivity of this type of piled wall. The improved capabilities of piling rigs available, as well as developments in concrete technology and instrumentation, have made this possible."

Jan 1, 2005

By R. L. Xu

In this paper, the author would like to point out with figures that the building industry is one of the key industrial sectors of the national economy in China. And in the coming 15 years, the output of building construction will not in the least decrease, but increase. The requirements for building standards, quality, functions as well as physical environment will also be higher along with the incessant development of the national economy and the gradual raising of people's living standard. China is a country with a vast territory and a great, variety of physical characteristics. The topographic and engineering geotechnical conditions are complex and varies considerably from place to place. Although, in recent years, encouraging progress has been made in building construction, there still exist many problems unsolved or even not explored at all, which we have to tackle in the future design and construction of foundations. Also reviewed in this paper are the achievements attained in the past thirty odd years and the challenge we will face in the foundation engineering field in China.

Jan 1, 2010

By Babak Mamaqani, Pirooz Barar

Regional Connector Transit Corridor (RCC) is part of the Los Angeles metro expansion project under construction which adds three new stations into the system. PB&A was responsible for the design of the support of excavation (SOE) systems for two stations, 2nd/Broadway and 2nd/Hope, in RCC. In this paper, challenges and lesson learned from SOE design of 2nd/Broadway station with a main focus on underpinning design are discussed. 2nd/Broadway station required to cut and cover excavation of 500 ft long by almost 100 ft deep, underneath 2nd Street. SOE systems consisting of drilled soldier beams with tiebacks and/or struts. The main challenge in 2nd/Broadway station was to underpin the LA Times building which was partially protruded into the station. A chellenging underpinning system consisted of concrete panels and ground anchors was designed to support the building surcharge and prevent settlement. The underpinning system was designed based on METRO design criteria and the deflection was evaluated by Finite Element Analysis (FEA) program, PLAXIS 2D. A maximum deflection of 0.4 inches was calculated to occur at the top of the underpinning system. Data from settlement and tilt sensors showed minimal movements which aligned with PLAXIS outputs. PROJECT DESCRIPTION The Regional Connector Transit Corridor (RCC) is Los Angeles Metro’s ambitious Light Rail Project. It runs under the City’s main thoroughfares, Flower and 2nd Streets, and when complete will alleviate traffic and parking congestion in downtown Los Angeles. The Regional Connector will connect thousands of residents living in the bedroom communities of the Inland Empire and Long Beach to their jobs Downtown. The rail line will serve 1.9 miles, using the $1.756 Billion budget to construct the underground rail line, including 3 new stations, at 2nd & Hope Street, 2nd & Broadway, and 1st St. & Central Ave (Fig. 1).

Jan 1, 2019

By Frank Rausche

Although Quality Control (QC) during construction is preferable for deep foundations, there are many instances when it is necessary to resort to Quality Assurance (QA) methods if, for various reasons, QC is not possible. Non Destructive Testing (NDT) methods for deep foundations are indirect approaches, i.e. in complex situations they do not provide complete information and need to be augmented by additional testing and/or analyses. While the challenges are varied for the different deep foundation types and the different test methods they are the same in many different countries. Experience of the tester is often mentioned as being most important for a successful quality assurance. In addition, reliable testing equipment for the best possible measurements and complete construction documentation for a meaningful data interpretation are minimum requirements for a successful test outcome. Another problem is the widely varying cost of the QA tests. For that reason the specifying engineer or authority has to be aware of what can reasonably be expected so that technically feasible specifications can be written for optimal cost and minimal construction delays. This paper discusses the most common NDT methods with a view on how these methods are applied world wide. It summarizes features of specifications, recommendations for test procedures and advanced analysis methods which can help to overcome uncertainty in the quality assessment of the foundation. Finally, the authors propose a decision tree for various QA methods, deep foundation types and soil properties.

Jan 1, 2008

By Fathi Abdrabbo

Open caissons are used for many geotechnical engineering applications. Open caissons may be used as deep foundation elements bypassing weak soils to tip in firm deeper strata, and in rivers and maritime construction to reduce the risk of scour. Open caissons are also used for collecting sewage water through gravity sewer pipe networks or from sewer force mains. In such applications, the design and construction of open caissons require a detailed soil investigation program. In this way, the design and construction plan of an open caisson can be developed with full knowledge of the prevailing subsoil conditions. The engineering and construction techniques are key factors to achieve functional caissons. Based on close observations during construction stages, the current study presents some challenges that were encountered during the construction of two open caissons of internal diameters 20 m and 10 m (65.6 ft and 32.8 ft). This paper describes the procedure followed to alleviate the construction difficulties encountered. Site exploration program and control measures required to satisfy design and construction requirements are crucial aspects. Sinking of open caissons in dense or very dense sands is risky. Incorrect sinking of open caissons may cause extra cost, delay in construction, and harm to nearby structures. Air/water jetting near the cutting edge of an open caisson, outside slurry trench, and/or inside open trench may be used to drive an open caisson downward. Unsymmetrical work around an open caisson may lead to tilting of the caisson. If this occurs, the tilt should be immediately corrected before resuming the sinking process. Improper cleaning of fine materials on the caisson?s excavation bed, and/or inappropriate pouring of underwater concrete may result in a defective concrete seal. The paper contains a series of practical guidelines to assist those intending to use open caissons, and shares good caisson sinking practice with practitioners. Finally, the study aims to understand the difficulties encountered and to anticipate future problems.

Jan 1, 2012

By Eric S. White, Thomas J. Sabourin, Khuram R. Mohib

"This paper presents the challenges associated with the design and construction of a steel sheet pile cofferdam supported with one level of grouted anchors in clean to silty sand with gravel. The initial assessment of the subsurface conditions indicated loose to medium dense soil with intermittent dense to very dense layers with no occurrence of cobbles and boulders. Sheet piles were proposed to be installed to a depth of 24 m below the ground surface to limit dewatering requirements for the cofferdam. During sheet pile installation, refusal of piles occurred at multiple locations forming passages for increased flow into the cofferdam. Modifications were made in the design of the dewatering system as a result of the increased flow. Finite element modeling was used to select the necessary modifications to the dewatering system within the cofferdam. Wells were installed based on the findings of the numerical model. Model simulations showed good comparison with monitoring of the field installed dewatering system.INTRODUCTIONIt is necessary to consider the impact of the ground water, subsurface stratigraphy, strength, and drainage behavior of the soil for the design and construction of cofferdams. This paper presents a case history of the construction of a cofferdam in Northern Ontario, Canada. The project consists of the construction of a powerhouse, intake, and tailrace which will generate around 28 MW of renewable clean energy by diverting water from New Post Creek through a power house and discharge into the Abitibi River. The focus of this paper is the dewatering and excavation support required to permit construction of the powerhouse. The layout of the cofferdam is shown in Fig. 1. The cofferdam for the powerhouse is rectangular in shape with sheet piles on all four sides intended to be driven to the design toe El. 101 m. The east and west walls have a length of 46.3 m. North and south sides are 47.6 m long; and in addition, two cantilever sheet pile walls bound the tailrace on the west side and two cantilever walls were installed on the east for construction of the penstock inlet. The ground surface in the powerhouse cofferdam area, before commencement of sheet pile driving, was brought to El. 125; the ground then slopes up to the East, toward New Post Creek, and the site is bounded on the West by the Abitibi River. 186 pairs of sheet piles were used to create the cofferdam and cantilever walls. The deepest excavation is to elevation 114.4 m. Within the west half of the cofferdam footprint, the base of excavation slopes upward at 3H: 1V to facilitate the tailrace discharge into Abitibi River.SOIL STRATIGRAPHYThe cofferdam design was based on the geotechnical investigation conducted by AECOM (2014) which included two relevant boreholes near the powerhouse footprint. The ground elevation at the time of investigation varied between 131 to 129 m. The material observed to the full depth of investigation was comprised generally of coarse to fine sand and gravelly sand or a sand matrix with gravelly inclusions. Some intermittent layers of clay and silt intrusions were also observed. Generally the soils grade finer away from the river. SPT N60 values were recorded in two borings during the field investigation with values reported from 3 to 92. The in-situ conditions ranged from compact to dense with some loose and some very dense zones. Figure 2 shows the variation in SPT N60 values with elevation."

Jan 1, 2017

By Glen R. Andersen

"Two of the greatest challenges we face in managing our aging infrastructure are to perform accurate condition assessments and to realistically predict the risk of non-action. The aim of this paper is to discuss common pitfalls we face in performing accurate condition assessments of our aging infrastructure using the case history of a recent near miss at the Lake Manatee Dam in Central Florida. The dam was placed into service in 1967 and was inspected every couple of years by dam safety engineers beginning in 1978. Although there was substantial and repeated evidence of a serious piping and internal erosion problem in each of these inspections, the problem was overlooked by most of the inspection teams. In 2012, the inspection team concluded that: “the Lake Manatee Reservoir Dam is well maintained and is in very good overall condition.” However, in 2013 a new team inspected the dam from an entirely different perspective, identified potentially serious conditions, performed an integration of the historical inspection data and concluded that: 1) the Lake Manatee Dam was in a severely distressed state; and, 2) without an immediate intervention there was a high risk of an uncontrolled release of the reservoir most likely following a large rainfall event and prolonged opening of the service spillway. This case history highlights human factors contributing to the near miss including group think and focusing on changes from prior inspections. The integration of historical inspection data is recommended for managing our aging infrastructure.INTRODUCTIONThe engineering analytical techniques most appropriate for assessing an aging infrastructure can be distinct from those used for the original design. To adequately manage our aging infrastructure it is necessary to change our perspective from anticipating failure mechanisms and designing to prevent them to assessing condition, detecting the presence of potential failure mechanisms, and assessing the potential risks. In many circumstances the failure mechanisms currently active may not have been anticipated by the original design team.We have developed a substantial body of experience in the design of our infrastructure. Full scale and laboratory testing coupled with the application of scientific principles to model behavior has led to many powerful design tools. The continued serviceability of our infrastructure as its elements reach their design lives stands as a legacy to our profession. However, under the sustained effect of limited resources for maintenance and rehabilitation parts of our infrastructure are in a highly deteriorated state. Unfortunately, the condition of some of these has not been properly assessed. This paper focuses on the Lake Manatee Dam in Central Florida and the process used to clearly identify its highly deteriorated state. While there are many factors that contributed to the lack of a proper assessment of its condition, the focus herein will be on human factors and in particular how “Group Think”, “Aversion to Bad News”, and “Condition Assessments Based on Changes to Prior Condition” may have contributed to not properly identifying the development of a serious failure mechanism."

Jan 1, 2017

By Dan Brown

Renewal and revitalization of transportation presents a challenge in the need for replacement, repair, and improvements of existing bridges, as well as increased construction of transit systems within existing transportation rights of way. Difficulties with conventional deep foundation systems occur because of the limited site access, adjacent structures, the need to maintain traffic, and other constraints on construction activity. Major projects are often performed in a design-build contract environment in which the schedule is aggressive, and where speed and reliability represent major considerations. Foundation designers are confronted with a need to solve problems with a construction-oriented mindset, where typical experience with lowest cost solutions may not reflect the most effective approach. This presentation presents an overview of the challenges that may affect design and construction of deep foundations in this environment and the methods that have successfully been employed on several large transportation projects in the U.S.

Jan 1, 1900

By Ryan Nagle, Eric Lindquist, Rob Jameson, Kelli Mccurdy, Serena T. Jang, John Gouchon

This paper discusses the challenges associated with the design and construction of a deep basement in downtown San Jose, California for the 200 Park Avenue project. The aim is to present the critical design issues, how the challenges were addressed, details of the selected shoring design, and the performance of the shoring system during construction. The critical design issues that will be discussed related to retaining the deep excavation and constructing the basement include shallow groundwater, artesian pressures, settlement outside of the excavation, shoring earth pressures, and shoring wall movement. Subsequently, the paper will describe why a tied-back cutter soil mix (CSM) cutoff wall was selected as the shoring system and how it addressed the critical design issues. The design of the tied-back cutoff wall will also be discussed. Lastly, the performance of the tied-back cutoff wall during dewatering and excavation and how it compared to the design will be included. The performance was measured through a monitoring program, including survey data points and piezometers.

Oct 31, 2023

By Balasubramani M., Ramana P. V., Bairagi K.

This paper is a case study of an earthen Cofferdam, constructed for a deep excavation at Intake location in river Aaundha, Maharashtra, India. A 12 m (39 ft) deep excavation was made to construct the Intake well. The natural soil profile at this location is clay followed by rock. An earthen Cofferdam of maximum height 7 m (23 ft) was made around the periphery of the excavation. Cofferdam embankment and excavation slopes were analyzed using the finite element software PLAXIS-2D. Clayey sand was proposed as filling material during design, but clayey soil was used for the embankment formation during execution. The embankment was built up to 5m height in July 2017 and completely submerged due to monsoon. In February 2018 embankment height raised to 7m (23 ft) by filling the soil over the existing submerged embankment. After a few days of completion of the Cofferdam construction, the inside slope of the embankment had started sliding due to continuous dewatering. The design and execution of deep excavation with earthen Cofferdam for waterfront structures are challenging. The selection of filling material for embankment formation and dewatering techniques plays a vital role in the safety and stability of the embankments. Although all the safety measures were taken during the design, execution challenges are unpredictable.

Nov 1, 2022

By Glen M. Bellew, James F. Mehnert

"The Kansas City District-United States Army Corps of Engineers has completed the design modification of a pile supported floodwall located along the Missouri River in Kansas City, Kansas. This deep foundation supported floodwall protects over 2 billion dollars in infrastructure, is approximately 17 ft (5.2 m) tall and is 1,446 ft (440.7 m) long. Design modifications included the addition of a row of drilled shafts and the addition of relief wells. Typically, deep foundation design is controlled by total stress analysis and undrained soil strength. Neither controlled design at this site, where effective stress and drained strength controlled. During high river stages, artesian pressures develop, leading to a reduction in both effective stress and pile capacity. Deep foundation analysis software available to the designer does not allow these effective stress conditions to be directly entered, so a unique way was developed to account for them. A load test was performed to verify the design. During load testing, the supporting ground was unsaturated and had effective stress conditions different from those that controlled the design. A load test evaluation process involving unsaturated soil mechanics was developed and performed. This paper will share both the effective stress design process used and the load test interpretation process performed.INTRODUCTIONThe Fairfax-BPU Floodwall is part of the Fairfax-Jersey Creek Flood Protection Unit in Kansas City, Kansas. The floodwall was built in the 1940s and currently provides Missouri River flood protection for over 2 billion dollars of infrastructure in the Fairfax Industrial Area. The floodwall averages 17 ft (5.2 m) in height, is 1,446 ft (440.7 m) in length and is divided into 35 separate monoliths. The originally constructed foundation support for each of these monoliths typically consisted of three rows of seven tapered steel monotube piles, each roughly 20 ft (6.1 m) in length. All monontube piles are tipped in sand, well above bedrock."

Jan 1, 2016

By Tomio Tsuchiya

A construction method of bored steel H piles enclosed in soil-cement columns was developed by modifying steel H piles from the driven pile method and soil-cement walls from the earth retaining wall method, the latter of which produces cut-off walls and reduces noise and vibration during construction. In this method, as shown in Figure 1, rich mix cement paste is injected into the bottom of a borehole which is pre-excavated by a casing auger, then a steel H beam is inserted before it hardens. Since the high vertical resistance of piles created with this method has already been confirmed by loading tests, we have been investigating the applicability of this method for piles used to temporarily support building loads for top-down construction on raft foundations until the raft foundation is completed. However, in the loading tests, the bearing capacity at the lower end of the pile was measured by loading from ground surface on test piles which had friction cut to eliminate the shaft friction resistance. In other words, the loading tests neglected the effect of overburden pressure of soil above the lower end of the pile. To investigate the effect of the overburden pressure on the bearing capacity at the lower end of the pile, loading tests were carried out on a bored steel H pile of lm diameter (test pile) bored in a compacted sandy soil layer with N-value of 100 to 250 at each stage of a three-step excavation. The results show no significant change in the bearing capacity at the lower end of the pile when the depth ratio of the pile is in the range of 5.7 to 22.7.

Jan 1, 1996

By Sudhir Kumar Das

"The exorbitant price of the land in the metropolis has restricted the horizontal expansion and compelled the owners, the developers and the engineers to opt for vertical expansion. This has resulted in the construction of high rises by extending floors of the existing buildings and developing the new ones for which deep excavation is a must. The multistoried buildings up to a certain height can be founded on shallow depth if the soil beneath can withstand the load. If not, the soil can be stabilized by the latest improvement technology to change the properties of soil to cater the desired load of the superstructures. By such practice the cost and time of completion of the substructures can be reduced in comparison to the substructures needed for deep excavation.The necessity of deep excavation cannot be ignored to create housings, underground parking lots and the other public amenities for the urban migrants in the metropolis.Although most of the metropolis have underground mapping the developers, before starting excavation should be hundred percent sure about the alignment and depth of the utilities so that the excavators do not snap the same to bring cut in water supply, power lines, telephone lines etc, resulting in hue and cry in the neighborhoods of the metropolis due to no availability of the essential services The building/structures coming on the influence zones of the deep excavation should be monitored in all sequences of excavations. In case of building underground corridors for rail or road through open deep excavation under a traffic road the developers, before commencing excavation should shift/divert the dry and wet utilities coming on the way of excavation to suitable locations. The surface traffic need to be diverted either temporarily to an adjacent alternative road or allowed to pass over a decking built over the trench of excavation for the affected length of construction. The soil support system is necessary longitudinally on the two sides covering the width of trench for building corridors. In case of building substructures of flyovers built at different plots along the alignment of the flyover or a multistoried complex built at an isolated plot, the soil support system would be necessary on all the sides covering the plot of construction.The material of construction of soil support depends on the depth, type of soil and the type of permanent structure to be developed. Probable geo-hazards inviting casualties in the deep excavation projects occur due to caving of soil, leakage of wet utilities, seepage through honey comb concrete surfaces, failure of pump used for dewatering etc. A detailed comprehensive planning, management and determination of the project authority is essential for marginalizing the casualties. These prevent unforeseen expenditure in mitigation and help to control the time and the cost over run of overall project. The engineer at site should be more a professional manager than an engineer at site. He should be conversant with the safety and environment rules and regulations applicable to deep underground projects."

Jan 1, 2015

By J. W. Wang

This article first explains the mechanism of forming strength in the Jet grouting reinforced foundation, and points out the function of cement hydrates and clay minerals in clayey soil, the reinforced body with the character of long-term growth of strength. Secondly, regarding the strength and the deformation characteristics of compound foundation, the article points out that the stress-strain curve of the jet grouting pile is approximate to hyperbolic curve. Finally, the article cites three examples of application in the construction of the metallurgical industry.

Jan 1, 2010

By Pratter P., Boley C.

Polymers are well established in geotechnical applications, for example in ground improvement, where the polymers act as a binder that, when cured, holds the grains together by adhesive and cohesive forces. The subject of this research work is an innovative composite of polymers and gravel, which differs from conventional grouting materials due to its adjustable material properties. With these specific properties, the semi-rigid material can be optimally adapted to the local ground conditions and the individual framework conditions of a construction project. For the characterization of the composite material, stateof- the-art methods, such as image processing by segmentation, are presented. Segmentation is suitable for quality assurance and monitoring of laboratory samples and soil samples directly from ground improvement on the construction site. The load-bearing capacity of the innovative material can even be increased to the order of magnitude of concrete. For this reason, the soil mechanical laboratory tests in this research had to be modified and even expanded by rock mechanical laboratory tests. Based on the experimental investigations, the importance of this innovative material for practical application is demonstrated by a calculation example from construction practice, which shows that even difficult ground conditions can be handled with it.

May 1, 2022

By Mu Chen, Ye-Shuang Xu, Dong-Wei Hou, Shui-Long Shen, Huai-Na Wu

"This paper presents a laboratory investigation on the mechanical behaviors of the cement-clay admixture improved by polypropylene fiber. Cement can significantly improve the clay admixture. The fiber additive also improves the strength and ductility of the improved clay. The Unconfined Compression Strength (UCS) of the polypropylene fiber-reinforced cement-clay presents an overall trend to grow with the increase of fiber length. The improved clay reached its peak strength at the fiber content of 0.5%. Then the UCS of the improved clay will slowly reverse if the fiber content continues to rise. For study of curing time, improved clay behaves better in its early strength, but an inhibition will be brought about if fibers are excessive.INTRODUCTIONGround improvement technology is essential for construction of structures in soft ground. Some traditional techniques often cost much but result in little. For instance, along the coastal region of China, soft ground is often improved by backfill with high quality sandy soil transported far away, leading to high additional haulage costs and long construction period. Reutilizing the excavated soil as backfill or subgrade after treatment, by contrast, will be more economical and effective (Hufenus et al., 2006). Many researches have been conducted to improve the compression strength of soft soil, among which, the method of mixing the soft soil with cement and fly ash is one of the most common ways (Kolias et al., 2005; Horpibulsuk et al., 2009; Porcino et al., 2012). It is known that soil resists well against compression and shear force but behaves poorly in resistance to tension. Therefore, utilizing tensile elements such as fibers and strips to improve the tensile strength will be effective because of its strength isotropy, better durability and cost effective (Haeri et al., 2000; Kaniraj and Havanagi, 2001; Consoli et al., 2010)."

Jan 1, 2015

By Mu Chen, Ye-Shuang Xu, Dong-Wei Hou, Shui-Long Shen, Huai-Na Wu

"This paper presents a laboratory investigation on the mechanical behaviors of the cement-clay admixture improved by polypropylene fiber. Cement can significantly improve the clay admixture. The fiber additive also improves the strength and ductility of the improved clay. The Unconfined Compression Strength (UCS) of the polypropylene fiber-reinforced cement-clay presents an overall trend to grow with the increase of fiber length. The improved clay reached its peak strength at the fiber content of 0.5%. Then the UCS of the improved clay will slowly reverse if the fiber content continues to rise. For study of curing time, improved clay behaves better in its early strength, but an inhibition will be brought about if fibers are excessive.INTRODUCTIONGround improvement technology is essential for construction of structures in soft ground. Some traditional techniques often cost much but result in little. For instance, along the coastal region of China, soft ground is often improved by backfill with high quality sandy soil transported far away, leading to high additional haulage costs and long construction period. Reutilizing the excavated soil as backfill or subgrade after treatment, by contrast, will be more economical and effective (Hufenus et al., 2006). Many researches have been conducted to improve the compression strength of soft soil, among which, the method of mixing the soft soil with cement and fly ash is one of the most common ways (Kolias et al., 2005; Horpibulsuk et al., 2009; Porcino et al., 2012). It is known that soil resists well against compression and shear force but behaves poorly in resistance to tension. Therefore, utilizing tensile elements such as fibers and strips to improve the tensile strength will be effective because of its strength isotropy, better durability and cost effective (Haeri et al., 2000; Kaniraj and Havanagi, 2001; Consoli et al., 2010)."

Jan 1, 2015