Search Documents

By J. C. Marchand, M. A. Berube

"L'objectif principal recherché lors du broyage d 'un minerai est de libérer adéquatement ses valeurs utiles en vue de leur concentration ultérieure. La pratique courante consiste à tenter d'obtenir un produit de broyage d'une granulométrie constante. Malheureusement, les propriétés texturales des minéraux utiles varient naturellement dans un gisement et une telle stratégie n'entraine pas toujours pour ces minéraux un degré de libération constant. Pour un rendement optimal du procédé de concentration, cette variable très importante doit donc être périodiquement vérifiée.Jusqu'à maintenant, la plupart des études de libération des minerais se font en examinant des sections polies de particules du minerai broyé. Le GRAAIM a récemment assemblé un système modulaire d'analyse d'images qui servira en grande partie à des mesures automatiques du degré de libération des minéraux. Le système s'avère relativement peu coûteux comparativement à la plupart des analyseurs de texture conventionnels si l'on considère que plusieurs de ses composantes, par exemple le miniordinateur, sont utilisées à une foule d'autres applications, et il permet de plus une grande souplesse d'utilisation puisque l'on a qu'à construire des algorithmes de mesure et de calcul en fonction de l'objectif recherché. Des programmes particuliers permettant des études automatiques de libération sur des sections polies de particules ont ainsi été élaborés. Ils permettent également des mesures de teneurs et de distributions granulométriques apparentes des particules. Des résultats obtenus dans le cas de minerais de fer sont brièvement présentés afin d'illustrer la technique."

Jan 1, 1983

By F. Ajersch, M. Rigaud, M. Jallouli

"Le gonflement des boulettes d'hématite à été étudié à l'aide d'une méthode de mesure standard ISO ainsi qu'à l'aide d 'une méthode de mesure dilatométrique.La première méthode a servi à l'étude des boulettes haute silice (5% SiO2) dont l'indice de basicité (IB = CaO + MgO -i- SiO2 + Al2O3) a été ajustée soit à l'aide d'une addition de dolomie, soit à l'aide d'une addition de pierre à chaux, soit à l'aide d'une addition de ces deux composes. L'indice de basicité variait de 0.05 à 0.12. Les résultats de gonfle ment obtenus à 1000?C dans une atmosphère de 40 CO - 60 N2 ont permis de montrer qu’indépendamment de l'indice de basicité c'est la dolomie qui contribue le plus à diminuer le gonflement par rapport à la pierre à chaux. L'utilisation de l'indice de basicité comme critère de sélection des boulettes est discutée.La méthode dilatométrique a servi à l'étude du gonfle ment de deux types de boulettes préparées à partir de deux concentrés de fer et dont la teneur en silice a été fixée à 2.5% et 0 5%. Ces deux types de boulettes ont reçues les mêmes additions de liant en quantité et en nature. La détermination en continue du gonflement, à 950?C dans 40 CO - 60 N2, a permis d'une part de mieux cerner le niveau de réduction auquel correspond le maximum de gonflement et d'autre part de montrer que l’allure des courbes de gonflement est étroitement liée à la nature du liant. Une augmentation de la teneur en silice des concentres contribue à diminuer le gonflement des boulettes.Des essais de réduction de gonflement non isothermes ont été réalisés à des montées de température à 10 et 20?C/min. Les résultats indiquent que le gonflement déterminé dans les conditions non iso thermes est inferieur à celui obtenu lors des essais isothermes. On discute alors de la validité des essais standards de gonflement qui sont utilisés pour prédire le comportement des boulettes lors de leur réduction dans un haut fourneau."

Jan 1, 1983

By Jorge Lema Patino

"The purpose of this paper is to determine the best techno-economic alternative for the treatment of tin ores, when comparing the various mining and metallurgical methods of preconcentration, concentration, volatilization (fuming) and up to the final stage of selling to the smelter. The study of the influence of the different parameters of cost, recovery and quoted prices has motivated the paper, which aims at determining the best process of ore treatment in terms of its techno-economic feasibility.Method of WorkOn the basis of head grades of 0.5, 0.75 and 1.0% tin, the following alternative methods of treatment are possible:1. Mining-Concentration-Smelting.2. Mining-Preconcentration-Fuming-Smelting.3. Mining-Concentration-Separation, with direct smelting and fuming/smelting of the two fractions produced.The calculations were carried out on the basis of existing information and publications concerning the various experimental recoveries in the operating mills of COMIBOL. In the case of concentrates containing less than 10% or more than 40% tin, extrapolation was required.The final grade of the tin concentrates and the gross weight of the concentrate were calculated on the basis of the estimated recovery curves. The costs of the preconcentration and the concentration stage s were determined per gross metric ton of material treated.The calculation of the cost of the smelting stage is similar for all the alternatives, the royalties and smelting charge varying with the grade of the final concentrate. In the fuming stage, a uniform recovery of 90% was taken in all cases so as to obtain a final concentrate grade of 65% tin, regardless of the head grade of the feed material.For the separation stage, the following considerations apply:a) Separation can be carried out by gravity separation or flotation methods.b) The cost of separation varies depending on the system used.c) The distribution of tin in the two fractions is 100% at this stage. In other words, there is no loss of tin during separation."

Jan 1, 1982

By Michael J. Sapko, Ellsworth R. Spencer, Frank J. Perzak

"The fire resistance of several mine conveyor belts is evaluated using a new belt-flammability apparatus developed by the U.S. Bureau of Mines. The test apparatus, experimental details and a calculated flammability index (FI) are described.The FI values are useful for ranking the fir e resistance of mine conveyor belts. Values are determined using parameters readily measured with thermocouples, high-temperature flow probes and a methane-oxygen torch, all of which are components of the Bureau's new test apparatus. The FI varies directly with the flame-spread rate and the rate of heat release during burning and varies inversely with the critical (minimum) ignitor energy output.The fire-resistance ranking of nine different belt types using this moderately scaled apparatus is compared with available full-scale data on belt fires. This comparison shows that the ranking based on the FI is consistent with the full-scale data.IntroductionFull-scale fire hazard evaluations of mine conveyor belts are not easily related to the properties usually measured in small-scale flammability tests. The inadequacy of small-scale belt fire tests has been demonstrated in works by Mitchell, Warner and Reinke.Mitchell and Warner showed that certain neoprene (NP) and polyvinyl chloride (PVC) belts, which had been approved by the Code of Federal Regulations 30 CFR 18.65, were nevertheless capable of propagating flame over their entire length when full-scale fire conditions were simulated. Comparable results were also observed by Reinke at the Tremonia experimental mine in Dortmund, West Germany, where all belts burned in full-scale tests even though they passed the small-scale tests. Only by reducing the severity of the full-scale test could these fire-resistant belts be grouped on a pass-fail basis."

Jan 1, 1982

By Dean S. Rogers

"In February 1980, Dome Mines Limited announced a $50 million expansion program which would result in a 50% increase in mill capacity from the present 1,815 tonnes per day to an eventual production rate of 2, 720 tonnes per day in the year 1984. As an integral and necessary part of this planned expansion, a new vertical production shaft, No. 8 Shaft, would be sunk from surface to a depth of 1,645 metres.Throughout the seventy-year history of mining at the Dome, gold has been found in a number of different rock types and in association with a number of different structural settings. However, the key to successfully locating ore deposits lies in the recognition of the favourable environments in which they generally occur. First and foremost, the exercise of locating the No. 8 shaft became an exercise in geological deduction based on the projection of these favourable lithologic environments.In November 1980, after detailed engineering work was completed, the total cost of the project was estimated at $75.5 million 1980 dollars or $91 million dollars allowing for inflation over a four-year construction period. These estimates include the shaft, significant replacement and alterations to the milling process, and an upgrading of the plant."

Jan 1, 1982

By M. Churchill, V. R. Degner

"Over the past two decades, declining ore body grades, increased operating costs and increased construction costs have provided an incentive for the development of progressively larger flotation machines. As a consequence, the 60 to 100 cubic foot flotation machine of the l950's and l960's is being rapidly replaced by large volume machines, with a resulting improvement in the flotation machine specific capacity (TPH processed per square foot floor space), specific power (HP per TPH processed) and process control simplicity. The recent development, and satisfactory plant evaluation, of the WEMCO 1000 cubic foot flotation machine provides the means by which further economic and operating advantages may be incorporated in high tonnage mill applications.The systematic development of the large 1000 cubic foot flotation machine, and its subsequent performance evaluation in beneficiating metalliferous ores (copper, zinc and iron) will be reviewed in this paper and recently completed plant results will also be provided."

Jan 1, 1982

By L. K. Nenonen

"Given the properties, locations and quantities of material to be hauled and the dump locations and capacities, the designer wishes to select the type and number of trucks and loading equipment required. Accordingly, software is being developed to assist in creation of the equipment, material and road network data bases, in selection of equipment, materials and road networks from these data bases, and in evaluation of the expected productivities both in a rapid, non-interactive, approximate fashion and a more detailed interactive fashion which permits the user to act as superintendent, if he so chooses. The basic technology has been developed and applied to an open-pit copper mine and is being refined and generalized for oil sands and coal mining applications.BackgroundA set of mathematical and interactive computer models are under development to aid in the selection of equipment and operating policies for an open-pit oil sands mine being planned by Canstar Oil Sands Ltd. This paper describes the computer models being developed of truck haulage systems. Although the interactive truck haulage model is based primarily on a model developed by the National Research Council in collaboration with Glenayre Electronics Ltd. of North Vancouver and Lornex Mines Limited(2).(3l, substantial changes and improvements are being incorporated to greatly increase its generality re equipment types, road network characteristics, dispatching and supervisory policies, etc. Although this paper is principally devoted to the truck haulage model, discussion is included concerning its interactions with other models."

Jan 1, 1982

By R. C. Beard

"The Ontario Ministry of Natural Resources has recently initiated several incentive programs to encourage and facilitate the development of new mines in northwestern Ontario. Some are privatized out to consultants and contractors. The status of three of these programs will be reviewed in this paper.IntroductionOne of the main objectives of the Mineral Resources Group of the Ontario Ministry of Natural Resources is to encourage and assist mineral exploration and the development of new mines in the Province. Programs to accomplish this objective are largely carried out through two Branches in the main office (in Toronto), the Mineral Resources Branch and the Ontario Geological Survey, and also a number of regional field offices scattered across Ontario.The function of the Mineral Resources Branch is to identify and administer effective policies that will ensure maximum benefits to the Province from mineral resource extraction.One of the most important factors in ensuring effective exploration in the Province is the availability of a good geosciences data base from which to work. It is the responsibility of the Ontario Geological Survey to develop and continually update this data base, providing, to both the public and private sector, an inventory and analysis of the geology and mineral deposits of the Province.The main functions of the regional field offices are to provide technical data and advice to exploration companies and prospectors, to encourage and assist exploration, and to provide information and general assistance to producing and developing properties to facilitate resource development and extraction. This is accomplished through the offices of the mineral resource coordinators and resident geologists. In northwestern Ontario, these field offices are located at Thunder Bay, Kenora, Red Lake and Sioux Lookout.To accomplish their objectives, the Ontario Geological Survey and the regional field offices carry out regular, ongoing geoscience and other mineral resource programs, under their base funding."

Jan 1, 1982

By R. W. Boyle

"EDITOR'S NOTEPart 1 of this paper, published in the August issue, covered lithochemical surveys based on major, minor and trace elements in whole-rock samples from primary enveloping halos.Part 2, which follows, continues with discussions of surveys based on leakage halos, zonation of elements, stable and radioactive isotopic distributions, and geothermometric, geobarometric, thermoluminiscent, pedochemical, hydro-chemical, atmochemical and biogeochemical methods. It concludes with a selected bibliography.Surveys Utilizing Leakage HalosLeakage halos can be used as scalar or vector quantities in thesearch for deeply buried blind mineral deposits. In the first case, the occurrence of a leakage halo (e.g. a small pitchblende seam) may simply indicate the possible presence of pitchblende mineralization or orebodies; in the second case, the areal or three-dimensional distribution of leakage halos may, by their increasing frequency and I or increasing metallic or gangue element content, provide a means of vectoring in on loci of mineralization and orebodies. Examples of both cases are given in the following text.Leakage halos are of many types, as shown in Figure 2 (Part 1), and are best discussed with respect to their associated mineral deposits. Furthermore, it should be noted that leakage halos are frequently offshoots or extensions of enveloping halos. Where this occurs, careful tracing of the leakage halo(s) downward or upward respectively will often lead to the apex or nadir (bottom) of the enveloping halo(s) and ultimately to mineralization or ore."

Jan 1, 1982

By W. N. Hamilton

"Evaporites abound in the Western Canada sedimentary basin, recurring throughout the stratigraphic column and widely scattered over the basin region. Alberta, situated centrally over the basin, includes many of the evaporites within its borders, but only a few have the right geological conditions to form potential economic deposits of salt or gypsum. These include the Middle Devonian Elk Point Group and related evaporites, Upper Devonian Wabamun Group-Palliser Formation evaporites, and evaporites of the 'Triassic Charlie Lake and Whitehorse formations.Salt deposits underlie almost half of Alberta. The major deposits belong to the Elk Point Group, which includes thick salt units in the Lotsberg, Cold Lake and Prairie Evaporite formations. Another, younger salt deposit in the Wabamun Group has only local distribution. Elk Point salts have a maximum aggregate thickness of 430 m in east-central Alberta. The deposits deepen southwestward across the province, from minimum depths of210 m at Fort McMurray to 1820 m at Edmonton.The thickest, most extensive salt deposits are the upper Lotsberg and Prairie Evaporite salts. Both have excellent development potential. The upper Lotsberg is up to 150 m thick, consists of clear, very coarse crystalline halite with only minor impurities, and has a notable lack of non-salt strata in its succession. Analytical data for the Lotsberg Salt show extraordinary chemical purity. Prairie Evaporite Salt differs lithologically from the Lotsberg in having a significant non-salt component. The deposit is up to 200 m thick and consists of medium crystalline halite, brownish coloured and cloudy as a result of finely dispersed impurities. The main impurities-shale, anhydrite and dolomite-are most prevalent as interbeds in the salt succession, ranging from very thin laminae to beds several metres thick. Although of lesser purity, the Prairie Evaporite Salt is shallower, thicker and more extensive than the Lotsberg and the salt quality is quite acceptable for most industrial uses."

Jan 1, 1982

By M. Leroux, J. A. Finch

"Sizing below 38 µm (400 mesh) is an increasing requirement in mill testing laboratories. The Cyclosizer is gaining wide acceptance in this role. A recent alternative is to use electro-formed sieves (micro-sieves), which are available with openings down to 5 µm. The advantage of micro-sieving is a cut size which is independent of mineral density, easier retention of the fi nest fraction and reduced purchase cost. A simple method of microsieving using an ultrasonic bath, which performs readily to 10 µm, is described.A systematic study of Cyclosizing and micro-sieving is reported for three samples; silica, copper oxide and a lead concentrate. Micro-sieving gave comparable results. Comparison with a standard sizing method, the Sedigraph 5000D, revealed misplaced material in each fraction by both methods. The range for micro-sieving was from 20% to 60% depending on the sieve and material; for the Cyclosizer it was a consistent 40-50% for all cones and all materials. The Cyclosizer can be sensitive to feed mass and particle size for dense materials. It is recommended that for minerals of specific gravity greater than 5, no more than 35 g of -38 µm be used.The disadvantage of micro-sieving is that it requires continuous operator attention and sieving time depends on sample mass. To fractionate 35 g-as used on the Cyclosizer and considered at reasonable mass for mill testing purposes-through 25-, 15- and 10-µm sieves requires about 80 minutes.IntroductionParticle size has a pronounced influence on mineral separation processes. Consequently, the measurement of particle size plays an important part in mill testing. By far the most common method is by screening. This, however, is usually limited to 38 µm (400 mesh) or occasionally 25 µm (500 mesh). Increasingly, mineral products are becoming finer than this limit and consequently finer sizing methods are required."

Jan 1, 1982

By P. Hanniala, S. Harkki, B. Andersson

"The Outokumpu Flash Smelting Process was put into commercial operation in 1949. The original process was based on the use of preheated air. The adoption of oxygen enrichment of the flash smelting process air in 1971 was a crucial improvement, especially for smelter capacity. Oxygen use according to the Outokumpu method means selection of the most suitable oxygen content for the process air on the basis of the concentrate composition, capacity and matte grade. The furnace is not bound to only one fixed degree of process air oxygen enrichment; the oxygen content may vary from 21% to 100%.The degree of oxygen enrichment and the matte grade are the most important process parameters in reducing the operating costs of the whole system, including smelting, converting and acid production. Raising the matte grade allows more efficient use of the reaction heat in the smelting stage. Sulphur is recovered in a high-strength, constant-flow gas stream. The blowing time in the converters is reduced considerably.Oxygen enrichment and high matte grade improve the energy efficiency of the plant complex as long as the surplus heat from the system is not wasted. When the operating costs and investment expenditure of the total plant complex are taken into account, a reasonably high degree of oxygen enrichment (35-80°/0) is the best alternative in practice. Existing operating smelters have achieved single-stream thoughputs of over one million t/yr of concentrates.HistoryLocal capital and operating costs as well as lower energy consumption per unit of metal produced are now the crucial factors in determining the choice of process. In the late I940s, the same reasons prompted Outokumpu to develop the original flash smelting process in Finland. Between 1900 and 1940, very few technical changes in pyrometallurgical copper production took place. However, the commercial use of the flash smelting technique began a new era in metal extraction from sulphide concentrates. The characteristic feature of the method is that the concentrate is smelted in suspension: this offers the most favourable conditions for heat and mass transfer, and thus high reaction velocities. Outokumpu was the first to exploit the known advantages of flash smelting in a commercial installation at Harjavalta in 1949."

Jan 1, 1982

By A. J. Sinclair, N. Champigny

"The Cinola gold deposit in the northern Queen Charlotte Islands, British Columbia, is in a clastic sequence consisting of a lower shale of the Late Cretaceous Haida Formation and an overlying interbedded sequence of pebble conglomerate and coarse-grained sandstone of the Middle Miocene Skonun Formation. Both formations are intruded by a stock and dykes of porphyritic rhyolite. Two K-Ar model ages indicate mineralization and probably porphyritic-rhyolite intrusion at about 14 Ma (middle Miocene). A splay of the Sandspit fault system constitutes the footwall on the west of the deposit.The Cinola deposit can be classed as Carlin-type based on features such as (1) small particle size for gold, (2) Tertiary age of mineralization, (3) element abundances (e.g. high Hg), (4) dominantly argillic alteration, (5) a structural setting associated with major faults, (6) porosity of the host rock and (7) spatial and possibly genetic association with felsic intrusions. Gold is widespread and occurs mainly as grains of< 0.5 11-m in silicified sedimentary rock, and in quartz veins. Locally, coarse > 100 11-m particles of native gold occur in quartz veins, especially in strongly brecciated porphyritic-rhyolite. Ore minerals are mainly pyrite and marcasite, but include small amounts of chalcopyrite, sphalerite, galena, pyrrhotite, cinnabar, tiemannite (HgSe), rutile, magnetite, hematite and limonite in addition to native gold and electrum. No silver minerals have been found; silver was found in gold particles in amounts varying from 6.2 to 24.2 weight per cent. Alteration products are sericite, illite, kaolinite and chlorite, with abundant quartz of several stages.The host rocks, specifically the Skonun Formation, formed as an alluvial plain facies in a braided river system discharging into a marine basin in early Middle Miocene time. During the Middle Miocene, this sequence was intruded by a rhyolitic stock. The highly porous and permeable Miocene clastic sequence apparently provided an optimum setting for the development of a large geothermal system, the energy for which probably derived from the rhyolite stock. Mineral deposition followed a well-defined paragenesis, which, from oldest to youngest, is: (1) precipitation of iron sulphide minerals, and early quartz; (2) several stqges of quartz veins, with deposition of sphalerite succeeded by galena, chalcopyrite and visible gold. Micron-size gold was precipitated throughout these two stages of mineral deposition. Argillitization of the host rocks probably in part coincided with the mineralization and continued during cooling of the geothermal cell.In-situ reserves have been estimated at 41.1 million metric tons averaging 1.85 g Au/tonne using a cutoff grade of0.86 g Au/ tonne."

Jan 1, 1982

By C. B. Webber, W. A. Grell

"Sherritt Gordon's Ruttan Mine is a copper-zinc operation located approximately 600 miles north-west of Winnipeg. Open pit mining began in 1973 at 10,000 Tpd., with a change over to underground mining in 1981 producing 7,500 Tpd. Ore is crushed to -3/4"" followed by rod and ball mill grinding (two ball mills in series), differential copper-zinc flotation, and dewatering. The copper and zinc concentrates are trucked 75 miles to Lynn Lake, where they are shipped by rail to the HBM&S smelter at Flin Flon.This paper describes a method used to predict the effect of grind particle size on metallurgical performance, as well as details on the copper and zinc metallurgical performance due to fine grinding in actual plant operation.Initial statistical studies on historical data (including ore source, head gr3de, grind, etc.) indicated that copper and zinc recoveries increased with fineness of grind, in the range of 50 to 65% -200 mesh.In order to extrapolate beyond 65% -200 mesh, and to develop expected nonlinear relations between grind, Cu concentrate grade, and recovery, the assays of screen fractions of copper concentrate and tailing were used to determin8 the relation between net smelter return (a function of grade and recovery) and grinding cost. The optimum economic grind would be that grind at which the net smelter return less grinding cost reached a maximum."

Jan 1, 1982

By L. A. Homeniuk, R. Bonnar

"The Athabasca Basin has been the scene of an intense exploration effort since the late 1960s, resulting in the establishment of this area as one of the major uranium districts in the world.The A thabasca Group is of Helikian age and unconformably overlies metamorphic rocks of Aphebian and Archean age. Most of the known uranium deposits have a close spatial relationship with the unconformity, graphitic meta-sediments, major northeast-trending structures and the basin edge. It should be noted that, in regard to the latter, some of the Cluff Lake deposits are exceptions.The pre-Helikian rocks underlying the Athabasca Group have been divided into six Iithostructural domains. The known uranium deposits are concentrated in the Wollaston and Mudjatik domains in the southeastern portion of the basin.The orebodies typically have a narrow high-grade portion below the unconformity and a broader, lower-grade disseminated zone in the overlying sandstone. Over-all grades average over 1% U3O8 and our estimate of known reserves totals more than 400 million pounds of contained U3O8. Some of the deposits have high concentrations of other metals, including nickel, arsenic, cobalt and gold. Ubiquitous chlorite and clay alteration is characteristic of the orebodies.Other Proterozoic basins in Canada of similar ages and having analogous geological settings to the Athabasca have received far less attention. Although little of the known uranium mineralization in these basins is related to the Helikian unconformity, there may be an exploration potential for deposits similar to those of the Athabasca basin.IntroductionThe Athabasca sedimentary basin is located within the Churchill Structural Province of the Canadian Shield in Northern Saskatchewan. The basin is elliptically shaped and is approximately 800,000 square kilometres in area.The objective of this paper is to summarize the various elements in the genesis of the unconformity-type uranium deposits of the Athabasca Basin and to evaluate the comparative potential of other Proterozoic basins to host similar unconformity-type deposits."

Jan 1, 1982

By M. Lytle

"The Corbin area of southeastern British Columbia has been a coal mining area since 1908. Byron Creek Collieries Ltd. Has operated its Coal Mountain Mine in this area from 1974 until the present. In February 1981, this company was purchased by Esso Resources Canada Ltd.Coal Mountain is structurally complex and standard computer algorithms are not applicable to model the overturned synclinal structures and faulted bedding surfaces. This paper discusses two approaches used by Esso Resources staff to model the geology of Coal Mountain.The first approach projects digitized cross-section data along trend to develop a large data base which correctly approximates the shape of the structure. The spatial orientation of the structure is corrected by merging the generated data set with drill-hole data. The second approach uses digitized cross-section and bench-plan geology to generate a block model of the coal reserve.HistoryThe Coal Mountain Mine, also known as the Corbin Mine of Byron Creek Collieries Ltd. is located 24 kilometres south of Highway 3 in southeastern B.C.In 1905, two American businessmen recognized the coal potential of the area during a horseback tour. The two businessmen, D.C. Corbin and E.J. Roberts, formed the Corbin Coal and Coke Co. to mine and market coal from their newly acquired 6075 hectares of coal licenses. By 1908, the town of Corbin was under construction, a 22.4-km rail spur was constructed from the mine to the main CPR line and the first underground mine began to produce coal. An open-pit operation was also developed at the 1828-metre elevation using a steam shovel loading into rail cars. The company operated continuously until 1935, when a lengthy strike forced suspension of operations.In 1943, the Consolidated Mining and Smelting Company Ltd. (now known as Cominco Ltd.) operated two surface mines to produce coal for its smelters at Kimberley and Trail, B.C. This operation ceased in 1948."

Jan 1, 1982

By G. Taylor

"The Iron Ore Company Of Canada's Carol Project is located in Labrador City, Newfoundland. Labrador City is some 912 air kilometers northeast of Montreal, and 417 ratl kilometers north of Sept-Iles, Quebec.Over 2,800 employees work at the Carol Project to produce some 20.0 million tonnes of concentrate and 10.5 million tonnes of pellets annually.In 1979 our Training Department started to develop the DACUM System of training for our Concentrator Operations Department.DACUM is an individualized, self-learning, training program. It is both a curriculum plan and an evaluation instrument.To date, the DACUM System has been completed for all occupations in the concentrator and work will commence shortly to develop DACUM for our Pellet Plant and Mine Operations Departments."

Jan 1, 1982

By G. J. Borbely, E. A. Devuyst, V. A. Ettel

"A new method for oxidative destruction of cyanide in industrial waste waters and slurries, such as gold mill barren liquors, tailing slurries and flotation tailings has been developed at the Inca research laboratories. Rapid decomposition of cyanide and related species is attained by treating the waste waters with a mixture of S02 and air at controlled pH and in the presence of a small amount of copper which acts as a catalyst. The approach selectively oxidizes cyanide and metal cyanide complexes, and also removes iron cyano complexes which are not removed by alkaline chlorination.The new method is shown to be less reagent intensive and therefore more economical than alkaline chlorination for treating gold mill and flotation waste waters. INTRODUCTIONOver 90% of the gold mined in Canada is extracted from the ore by ""cyanidation"". Wastes from the process consist of tailings which contain free cyanide, cyanide combined with heavy metals, thiosalts and thiocyanates. Because of the concern over the effect of toxic cyanides on the environment, all cyanide containing effluents will have to be treated in the future to meet certain government set concentration limits."

Jan 1, 1982

By W. D. Sinclair

"Between 1934 and 1956, nearly 31 million grams of gold were produced in the Matachewan area from deposits on properties belonging to Young-Davidson Mines Limited and Matachewan Consolidated Mines Limited. In 1979, production from these properties was renewed by Pamour Porcupine Mines Limited.Most of the gold produced has come from relatively lowgrade deposits (3.4 gl t or less) that occur in an east-trending belt of dykes and irregular bodies of trachytic syenite. Although small by comparison, these deposits have some of the characteristics of porphyry copper-molybdenum deposits. The mineralized syenite contains up to 5 per cent disseminated pyrite and is highly fractured and cut by quartz and quartzcarbonate veinlets. Gold occurs as native gold along fractures, in quartz veinlets and as minute inclusions in pyrite. Minor chalcopyrite and trace amounts of scheelite, molybdenite and galena are also present. Mineralization was accompanied by potassic alteration, consisting mainly of potassium feldspar.Some gold was also produced from small, but higher-grade, deposits in volcanic rocks. These deposits occur near the syenite-hosted deposits and consist of quartz veins and stringers mineralized .with pyrite and gold. Minor gold is present in some low-grade, porphyry-type copper-molybdenum occurrences and, locally, in large, isolated quartz veins.Lead isotope analyses suggest that the gold deposits were formed at about 2700 Ma and were locally remobilized at approximately 2400 Ma, following the Kenoran orogeny. The deposits appear to be genetically related to felsic magmas emplaced in an epizonal environment and deposited from hydrothermal solutions relatively concentrated in S and K20."

Jan 1, 1982

By K. D. Eng, W. T. Tierney

"During the past century, the development of vehicular transportation has benefitted tremendously from the performance improvement in engines in a situation where low-cost, plentiful fuel supplies were the order of the day. Engine advances were enhanced by and also dictated fuel modification to better adapt the energy source to the power plant.In discussing the several aspects of the change in approach from ""an engine and its fuel to a fuel and its engine"", the authors touch on the following areas:1. Description of an engine concept that provides the needed flexibility in fuel appetite at good efficiency to cope with future requirement s.2. The constraints placed on liquid fuel resource energy utilization efficiency by special engine-required fuel properties and the fuel efficiency of the various engine types available.3. Future vehicle engine fuel sources. This review will put into perspective the problem associated with the net energy available from future fuel sources under extensive research and development at present.4. A brief review of test data to show that fuel-tolerant and fuel-efficient engines are viable and that, in a fuel-resource-limited future, they can be a ""light at the end of the tunnel.""The Texaco Controlled Combustion System (TCCS)The TCCS is a unique means for stratified charge operation of an internal combustion engine in such a manner as to eliminate the requirement for octane or cetane number specification for the fuel. Octane rating is an empirical engine test method that evaluates a gasoline&apos;s resistance to spontaneous ignition or ""knock."" Cetane is based on a different engine test, which determines a diesel fuel&apos;s ease of spontaneous ignition . High cetane number enhances cold starting and permits high-speed diesel engine operation. As one would expect, the fuels in current use cover a band when the two values, octane and cetane, are plotted against each other."

Jan 1, 1982