Search Documents

By H. Sato, Y. Sato, T. Ooishi, K. Sakamoto

"Sumitomo Metal Mining Co., Ltd.(SMM)'s Niihama Nickel Refinery(NNR) produces high quality Nickel cathode, Cobaltcathode and other by-products using hydrometallurgical refining process called “MCLE”(Matte Chlorine Leach and Electro-Winning). In 2005,NNR started to use nickel and cobalt mixed sulfide (MS) produced by one of the SMM’s subsidiaries Coral Bay Nickel Corporation(CBNC)’s HPAL plant in Philippines, although its main and the only raw material until then was nickel matte. With start-up of the second HPAL plant at Taganito in 2013, NNR expanded its production capacity of nickel cathode from 41,000 to 65,000 tpa and finally achieved its target in 2015 by producing 65,980 tpa. SMM developed the technologies to improve poor reactivity of MS and installed new facilities to cope with increased Cobalt and Sulfur production at that time. This paper describes the technical approach to increase MS treatment with high efficiency.INTRODUCTIONThe Sumitomo Metal Mining Co., Ltd.(SMM)Niihama Nickel Refinery(NNR) produces Nickel cathode, Cobalt cathode and other by-products using Matte Chlorine Leach and Electro-Winning (MCLE) process technology. SMM uses nickel matte and nickel & cobalt mixed sulfide (MS) as raw materials for the MCLE process. Table 1 shows typical composition of these raw materials. Nickel matte had been only raw material until 2005, and with start-up of Coral Bay Nickel Corporation (CBNC) operation in the Republic of the Philippines, MS became major part of it. In 2009, when CBNC doubled its production capacity, NNR also expanded its plant capacity of electrolytic nickel from 36ktpa to 41ktpa, keeping an eye on the possibility of 65ktpa with oncoming SMM’s second HPAL in Philippines. Poor reactivity of MS was the prime concern at that time because our intention was to increase production with MS. Nickel extraction rate deteriorated with increasing usage ratio of MS in raw materials. To keep high nickel extraction rate under high ratio of MS, NNR developed a new leaching technology. Another concern arising from treatment of MS was Cobalt and Sulfur contents that are much more than those of nickel matte as shown in Table 1.NNR introduced new technology of solvent extraction process as to Co/Ni separation process in order to keep cost competitiveness instead of the conventional cobalt oxidation–neutralizing method. As to sulfur products, new sulfur productive facility was installed to improve the exposure to sulfur dust and the hot working conditions for workers. As a result of process development and installation of new facilities against the problem with MSusage,65 ktpa production was achieved in 2015."

Jan 1, 2017

By E. M. De Souza, A. M. Coode

"When Canadian potash was brought into production in the 1960s substantial research was carried out to develop the technology needed to cope with the unique conditions in Saskatchewan mines. The intense research has established Saskatchewan's position as a leader in production technology on a world scale, and as a leader in setting international standards for potash production. The industry is now more than two decades old and, although the mines operate efficiently, there are a number oj prominent areas of concern. High among these is the prediction, prevention and control of sodium rich brine inflows. Control has proven difficult or elusive in the potash mining horizon, but work continues in this area. Control of brine in the superincumbent limestone formation has proven to be easier and more conclusive.The first part of this paper describes the rehabiltation, diamond drilling, and grouting completed at Central Canada Potash, which reduced the brine inflow from approximately 82 l/min . at the beginning of the work to O.9/1min. when the backfilling was placed.The second part of the paper describes the rationale for choosing the rock mechanical instrumentation, the reasons for their placement and the rock mechanical data recorded with some interpretation.IntroductionCentral Canada Potash is located approximately76 km southeast of Saskatoon, near the Yellowhead Highway. The commercial production of potash at CCP started at the end of 1969 at a depth of 1021m below surface. The potash zone, which is presently mined, is approximately 3.35 m thick . Stress relief methods using yielding pillars are used in the design of the mining layouts. The planned extraction ratio averages 35070 . The mine is designed to produce approximately 3.3 million tonnes of sylvinite per year to give approximately 1.3 million tonnes of finished product (muriate of potassium) per year."

Jan 1, 1990

By V. G. Minenko, A. L. Samusev

For efficient leaching of gold from sulfide ores and the oxidation of sulfides into sulfates, it is necessary to introduce a substantial amount of oxidant - atomic oxygen, hydrogen peroxide, ozone, potassium or sodium hypochlorite. In this paper, hypochlorite electrochemical treatment is proposed as an effective method of intensification of refractory ore leaching. The objective of the study is to increase the gold recovery from refractory ores with the application of chlorinated solutions that are modified by chemical or electrochemical treatment. The advantages of the use of the modified chlorinated solutions instead of cyanide for gold-sulfide leaching are considered to be the following: a high concentration of the oxidizing agent (hypochlorite ions) in solution helps to achieve a high speed of gold dissolution in the form of chloride complexes; the possibility to produce hydrochloric acid solutions that may be used for the recovering gold by electrolysis; the possibility of the processing of carbonaceous, arsenic-bearing and others kinds of refractory gold ores. The mechanism of the interaction of the modified chlorine solutions with gold-bearing sulfides (pyrite and arsenopyrite) was investigated. The efficiency of the application of chemical and electrochemical leaching method was proved. The main factor that limits the rate of gold dissolution is a high concentration of sulfate ions (SO4 2-) formed in the solution by the oxidation of sulfide minerals. The optimal parameters of chemical and electrochemical leaching method and effective ways to remove sulfate ions were determined. The method helps to increase the level of the gold recovery up to 87% from refractory ores. The intensification of leaching by chemical and electrochemical treatment opens up opportunities for the creation of modern efficient and environmentally-friendly technologies that may be applied for gold extraction from refractory gold ores.

Jan 1, 2016

By Jodi Roberts, Curtis Deredin, Jean-Guy Paulin

"Since the establishment of the Six Sigma quality improvement program in 2001, several projects have been successfully carried out in the copper-lead, zinc, copper separation, lead upgrading and bulk flotation circuits in the Brunswick Concentrator.This paper provides an update on the process improvement initiatives that have taken place since 2004 using the Six Sigma methodology:•,The recirculation of warm water to the flotation circuit (to save on energy costs)•,Installation of a heat recovery tower to recuperate the heat lost from the zinc dryers•,Installation of an extra row of cleaner-scavenger cells for the copper-lead circuit for extra capacity, and a new reagent scheme for the copper separation circuit that have increased copper and lead recoveries.INTRODUCTIONThe Brunswick Mine Concentrator (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The concentrator utilizes selective flotation to produce zinc, lead, copper, and bulk lead/zinc concentrates. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.Figures 1, 2, and 3 illustrate the historical annual average metallurgical performance and process improvements achieved at Brunswick Mine for the zinc, lead and copper concentrate products. The objective is to continuously direct metallurgical performance towards increasing grades and recoveries while minimizing operating costs."

Jan 1, 2008

By W. S. Urbanski, A. L. Devernoe, R. W. Stuart, M. S. Walker

"Although many investigators have successfully achieved separations using variations of a concept wherein particles are buoyed upwards against gravity in a magnetically attracted fluid, none have succeeded in separating fine particles in a manner that is practical tor mineral beneficiation. This paper describes laboratory tests and preliminary economic analyses for a new mineral separation process which provides enhanced magnetic buoyancy and separation capabilities. The process provides a means of gravity separation in a regime where conventional gravity separation is inadequate; that is for small differences in mineral densities and for very fine particles. Although early interest centers on gravity separation, the process has also been successfully used for precise magnetic separation.Tests were conducted on a variety of mineral mixtures, ore samples and concentrates including; a sphalerite ore, pyrochlore ores and concentrates, cassiterite pre-concentrates, a chromite pre-concentrate, and heavy mineral placer samples. Separations requiring high discrimination between fine particles narrowly different in density or weak magnetic properties were obtained. Of particular interest is the ability of the process to concentrate or remove oxide minerals or gangues, especially silicates. Potential applications are discussed."

Jan 1, 1985

By J. C. Loretto, H. A. Simons

The paper discusses how, in the routine testing of ores, insufficient communication between the laboratory and the design personnel can lead to misunderstanding or misinterpretation of test results and consequent design errors. A number of examples are given together with suggested modified interpretations and the resulting dollar savings indicated by these new interpretations.

Jan 1, 1972

By Esteban M. Domic

"T.L. Leaching ProcessCommercial PerformanceSociedad Minera Pudahuel Ltda. (SMP) has been innovating in the copper producing field with the commercial application of the Thin Layer (T .L.) leaching process in its two operating division s: Lo Aguirre and La Cascada. Since November 1980, SMP' s Lo Aguirre Division has been producing high-purity copper cathodes at a nominal rate of about 16,500 metric tonnes / year, by mean s of the new route of T.L. leaching, followed by solvent extraction and electrowinning (TLlSX/EW). This has been the first commercial application on T .L. technology in the world, and the only commercial application in Chile for solvent extraction and electrowinning.By mid -1980, SMP acquired Sagasca Mining Co., renaming it as La Cascad a Division. The existing vat leaching facilities were modified to apply T.L. in the same old vats. The existing scrap iron cementation recovery circuit was kept running for the continuing production of copper precipitates. The modifications in the leaching circuit allowed shorter treatment cycles with a lower acid consumption and consequently, copper product ion increased from a previous historical high of 12,000-13,000 metric tonnes /year to a new level of about 22,000 metric tonnes/ year . These changes have been in operation since March 1981.T.L. Leaching commercial performance, both at Lo Aguirre (TL / SX /EW) and at La Cascada (TL/cementation), has been presented in several recent publications. Real operating parameters and process requirement s were reviewed in detail. A breakdown for TL / SX/ EW economics was also published based on Lo Aguirre' s performance during 1982(41."

Jan 1, 1986

By G. Heinrich

Size by size recoveries and pentlandite liberation data from image analysis were used to evaluate plant tests of pentlandite flotation and pentlandite/pyrrhotite middlings flotation from pyrrhotite in a circuit treating low grade magnetic intermediates at the Strathcona Mill. Raising the pH with lime gave improved selectivity for liberated pentlandite but there were major losses of middlings unless the circuit was pulled hard indicating the need for finer regrinding. However, size by size recoveries at the normal regrind showed that, while the pentlandite recovery improved in the finer ranges, the pyrrhotite recovery also increased leading to little selectivity in any size range. A much finer regrind gave greatly improved selectivity in all size classes suggesting that 'surface polishing' as well as liberation effects were being seen. Using liberation data from image analysis of the products, surface polishing accounted for over 99 % of the improvement in selectivity. Unreasonable recoveries of more highly liberated particles were observed for liberation analysis by volume fraction but showed the expected trend in recovery when the analysis was based on surface liberation. The surface liberation data showed that the improved pentlandite recoveries after finer regrinding were to more than 90 % caused by improved liberation with the remainder contributed by surface polishing effects. The practical implications of this work are that i) the comparison of particle grades with product grades allows to estimate the effect of regrinding on co-flotation/entrainment, ii) surface liberation models should be used for evaluating recoverabilities by flotation and iii) regrind circuits may be set up to ensure that all particles go through the mill or that only the coarse fraction is reground depending on the surface scrubbing found to be required.

Jan 1, 1993

By Ferri P. Hassani, Riadh Bouzaïene

"Selected methods of pressure loss predictions in horizontal slurry flow in pipelines are presented. For a given combination of flow velocity, solids concentration and particle size, the slurry and its flow conditions are described, and an appropriate method of pressure loss prediction is outlined. The wide range of conditions treated in this paper may be found in practice in areas varying from the hydraulic transport of low concentration slurries to dense-phase conveying of paste backfill in underground mines.IntroductionThe hydraulic conveying of solid particles in pipelines is a major component of the mining and mineral processing industry. Whether the objective is to transport ore to the processing plant or to make use of mill tailing as backfill material; the need for well designed, economical hydraulic conveying systems is recognized.The contribution of this paper is part of an on-going research program at McGill University involved in optimizing and developing techniques for total mine waste disposal. One of the main concerns in the conveying of solid-liquid mixtures is the prior knowledge of the pumping power input required. This energy requirement is directly proportional to the pressure losses incurred in the pipeline system. Understanding the sources of such pressure losses and predicting their magnitudes should enable the system designer to make informed decisions regarding the optimum mode of hydraulic transportation commensurate with the over-all requirements of the operation.This paper is an attempt to classify pressure loss prediction methods encountered in the literature for solid-liquid mixtures. In spite of the large number of publications spanning thirty years of research in the field of slurry transportation, it is sometimes difficult to correctly identify the appropriate methods applicable to a given situation. This is partly due to the inherent complexity of the mechanics of slurry flow and the ensuing uncertainty about the nature of the flow regime under investigation.Our approach is to use three fundamental parameters, namely: flow velocity, solids concentration and particle size (for solid particles with a given density) to characterize the slurry and the flow conditions, and to match them with an adequate pressure loss prediction method. For each combination of flow velocity, solids concentration and particle size, a description of the most likely prevalent flow conditions and some known methods of dealing with them will be presented. Qualitative definitions of ""high"" and ""low"" magnitudes of the aforementioned parameters will be given as a general guide to the classification scheme presented in this paper."

Jan 1, 1992

By Jerry Gagnon, Matt Burr, Timothy Ellis, Abbas Mirza, Larry Webb

"The mechanical properties of RSR anode alloys (lead-calcium-tin, 009+ and lead-strontium-tin) were investigated as a function of time with an objective of developing lead anodes for use in high temperature electrolytic processes such as in copper liberator cells and in cobalt and nickel electrowinning. At a temperature of 70 oC, the mechanical properties of rolled RSR lead-calcium-tin (PbCaSn) alloy currently used in copper electrowinning decreased gradually while the mechanical properties of rolled RSR lead-strontium-tin (PbSrSn) decreased relatively quickly and stabilized at low strength levels. Cast PbSrSn started off as the weakest alloy but its properties remained stable with time. Rolled RSR 009+ anode alloy showed improvement in ageing properties over the other alloys tested. However, its mechanical properties did not stabilize in the study timeframe of 284 days. Further investigations are planned to study the effect of alloying elements on mechanical properties of RSR 009+ anode alloy over several years as a function of time at 70 oC. The mechanical properties will be evaluated to determine the time at which they stabilize. Comparative plant trials with rolled RSR PbCaSn and RSR 009+ will also be performed in copper liberator cells and in cobalt and nickel electrowinning tankhouses to determine their mechanical and electrochemical performance at temperatures of 65-75 oC.INTRODUCTIONLead-based alloys are the primary anodes used in the electrowinning of copper, zinc, nickel, cobalt and manganese from sulfate-based aqueous systems. Lead anode technology has evolved over the years migrating from pure lead and lead-antimonial alloys to the present day PbCaSn alloys for copper and PbAg and PbCaAg alloys for zinc electrowinning (Prengaman, Ellis and Mirza, 2010). It has also migrated from cast to rolled microstructures in search of improved mechanical properties and higher corrosion resistance. Although great strides have been made in the development of new lead anode alloys and production processes for lead anodes to be used in copper electrowinning, the industry still has some unresolved issues. These relate to the necessity of having higher mechanical properties especially for the lead anodes in liberator cells in copper electrorefining and for cobalt and nickel electrowinning as these tankhouses operate at temperatures of 65-75 oC compared to 40-45 oC in case of copper electrowinning."

Jan 1, 2016

By Parviz N. Farsangi, Ferri P. Hassani, Allen G. Hayward

"Kidd Creek Mines places approximately 10 000 tonnes of consolidated rockfill (CRF) daily. Consolidated rockfill comprises sized aggregate mixed with different ratios and amounts of binders. Consolidated rockfill is employed to simplify subsequent pillar recovery and provide improved passive/active ground support.The consolidated rockfill is designed to sustain not only the gravitational loading of the overlaying fill material, but also to some extent the dynamic loading applied during blasting of the adjacent stopes and/or pillars. This paper describes the steps taken to optimize the pre-sent fill system at Kidd Creek Mines.The emphasis is on four areas which have high saving potential: lower cost alternative binders, structural design, quality control measures, in-situ testing techniques for back analysis. A consolidated rockfill design optimization chart was developed from these investigations."

Jan 1, 1996

By J. B. Mawdsley

"The Red Lake Gold Shore mine is 4/5 mile west of the town of Red Lake, Ontario, and a mile northwest of the Howey mine. It came into production in August 1936, and in a little over 2 years produced 21,099.58 oz. gold from 83,949 tons milled.An investigation of this deposit was made by the writer during parts of September and October, 1937t. The geology of the deposit is also discussed by H. C. Horwood(2) , and the characteristics of the ore were investigated by the Bureau of Mines, Ottawa (1).The orebodies are pipe like and close together, in a north-northwesterly trending zone of dykes, veins, and shear zones in a granodiorite stock, just south of a pronounced valley with a trend of N.65°E. believed to lie along a strong shear zone and fault . The dykes, veins, and mineralization are believed to have been successively emplaced along structures having three general trends and that were due to compressive stresses that alternated, at least four times, from west of north to east of north. In common with many other gold deposits, the gold mineralization here occurred late and followed the last east-of-north stresses.WALL-ROCKSThe mine is within the Dome stock, % mile from its southeast margin. Near the mine the rock is a pink hornblende-biotite granodiorite, grading within short distances, but not abruptly, into a dark grey variety. Near the workings at least, scattered small inclusions form about ½ to 5 per cent of this body. Most of them are fine-grained, angular, or partly rounded, greenstone fragments, but some have been partly granitized and feldspar has been developed in them."

Jan 1, 1954

By S. Usui, Y. Shinohara, C. Tokoro, K. Horiuchi, S. Owada

Process optimization of heating and physical separation for Cobalt (Co) recycling from spent lithium ion battery (LIB) was investigated. LiCoO2 in spent LIB was transformed to LixCoO2 which was more easily decomposed than LiCoO2 by heating. Coexisting materials of aluminum and carbon, and sealed atmosphere of the LIB promoted LixCoO2 decomposition. In an atmosphere of Argon, 95 % of LixCoO2 in the spent LIB was decomposed to 76 % of Co oxide and 19 % of Co metal in 10 min at 823 K; a lower temperature than the theoretical value for LiCoO2. The Co oxide and Co metal exhibited magnetic properties and could be recovered by wet magnetic separation. Furthermore, slow heating was effective for grain growth of Co oxide and Co metal. At 2 K/min rate of heating, average grain size of Co oxide and Co metal were 239 µm and 28 µm respectively, whereas at 30 K/min they were 190 µm and 15 µm respectively. Therefore, separation efficiency for Co recovery by wet magnetic separation was increased when spent LIB was slowly heated at 2 K/min.

Jan 1, 2015

By Pierre Giasson

"Les avantages de l'électricitéLe thème de la réunion 1982 de l'ICM District No. 2: "" Le défi des années 80 pour l'industrie minière de la Côte-Nord"" exprime trè s bien la réalité . En effet, la récession économique qui touche présentement tout le monde industrialisé, frappe de façon particulièrement sévère le marché du fer et de l'acier. Il est donc primordial pour les industries minières de la CôteNord de minimiser leurs coûts de production. Comme on sait, une bonne part des coûts de production est directement reliée à la consommation d'énergie.Si on retourne en arrière de quelques années, les prix des produits pétroliers étaient beaucoup moins élevé s que maintenant . Par exemple: A Philadelphie, en janvier 1930, le prix de l'huile no. 6 (bunker C) était de 1.22$ le baril. En 1940, le prix mondial du pétrole brut se situait aux environs de 1.80$ le baril et augmentait très lentement jusqu'en 1973. A la mi-octobre 1973, l'organisation des pays exportateurs de pétrole (O.P.E.P.) surprend le reste du monde en annonçant que le prix du brut grimpe à S.12$ le baril. .. on connaît la suite.On sait qu'au point de vue énergétique, le nord du Québec est l'une des régions les plus avantagées au monde. Malgré le fait que notre climat soit plutôt défavorable, nous sommes assurés d'une alimentation électrique à toute fin pratique éternelle, contrairement aux autres régions du globe. En effet, l' hydro-électricité ne représente que 2.S070 de toute l'électricité produite dans le monde.Une bonne partie de l'énergie consommée dans les industries minières de la Côte-Nord est utilisée pour produire la vapeur. Or, il y a plusieurs avantages à produire de la vapeur à partir de l'électricité:1. Le prix d'achat d'une chaudière électrique peut être moins de la moitié de celui d'une chaudière à carburant fo ssile.2. Le prix de l'électricité est plus bas que celu i des autres sources d'énergie disponibles dans notre région.3. Hydro-Québec offre un programme spéci al de subventions et un prix garanti de l'électricité, inférieur de 10070 à celui de tout autre combustible (1982).4. Souvent il est possible d'utiliser l'énergie hors pointe à un coût minime.S. L'espace requis pour un chaudière électrique est beaucoup moindre. Par exemple: une chaudière d'une capacité de 120000 Ibs/hre ne demande que SO pi? de plancher, c'est-à-dire un cercle de 8 pieds de diamètre comparativement à environ 600 à 700 pi2 pour une chaudière au ma zout.6. Aucun espace n'est requis pour l'entreposage du carburant.7. Aucun espace n'est requis pour la cheminée.8. Il n' y a que très peu de pièce s mécaniques, donc ces chaudières demandent très peu d 'entretien .9. Les chaudières électriques ne génèrent aucune pollution, donc on n'a pas besoin d'équipement coûteux de contrôle de la pollution.10. Ces chaudières sont extrêmement rapides. En effet, on peut passer de zéro à la production maximum en moins d'une heure si la chaudière est froide et en quelques secondes seulement si la chaudière est à sa température d'opération.11. L'efficacité de ces appareils est au moins de 9S% par rapport à 80-8S% pour les chaudières au ma zout. De plus, cette efficacité demeure la même quel que soit le niveau de production de la chaudière. Il faut faire attention ici: les manufacturiers proposent des rendements de 99% et plus, mais ceci ne tient compte que des pertes de chaleur à travers l'enveloppe, et de l'énergie nécessaire au fonctionnement de la pompe de circulation. Il faut ajouter à cela l'énergie perdue à cause de la vidange qui varie selon le type de chaudière et selon la qualité de l'eau d'alimentation.12. Ajoutons simplement que ces appareils sont très facile à opérer du fait qu'il n'y a aucun système complexe à manipuler.Cependant, il y a un inconvénient non négligeable à utiliser l'électricité comme source d'énergie: comme on ne peut pas emmagasiner l'énergie électrique, nous sommes à la merci du fournisseur."

Jan 1, 1985

By Jean-Christophe Ehrström, Fanny Mas

"A specific test set-up has been developed to study at the lab-scale the high-temperature behavior of aluminium alloys in conditions close to those experienced by thick plates during hot-rolling. A particular attention is paid to reproducing both the stress triaxiality and strain fields that exist in plate during rolling. In addition to standard ductility measurements by means of secondary tensile tests (STT), multi-step plane strain compression (PSC) tests have been performed to mimic hot-rolling pass schedules. Tool and sample geometries were adapted to allow low h/a ratios (h= average specimen thickness, a= tool width) and thus guarantee depressive stress conditions at the center of the specimen during most of the test. Such conditions resulting in porosity opening can then be used to investigate the impact of rolling conditions on damage evolution. The mechanical testing was combined with post-mortem high-resolution ultrasonic scans allowing to detect small amounts of damage and quantify its evolution as a function of processing parameters such as strain and temperature. The test set-up was validated on two 2050-type AlCuLi alloys with different susceptibilities to high temperature embrittlement.INTRODUCTION Aluminium thick plates are widely used in the aerospace industry, mainly as semi-products to be machined for internal structure parts of wings (spars, ribs) and fuselage (frame). The conversion route of such products always involves a hot-rolling step, the conditions of which (temperature, speed, pass schedule) have to be optimized to maximize both mechanical properties and final plate quality. This goal cannot always be efficiently achieved by full-scale industrial trials as (a) cost limits the number of possible test conditions and (b) it is often difficult to change one parameter alone. That is why there is a need for laboratory-scale tests able to mimic the rolling process in terms of temperature, strain rate, stress triaxiality and deformation. Most laboratory hot-rolling mills do not adequately simulate industrial processing routes, especially in terms of heat loss, deformation speed and rolling geometry (maximum roll gap vs. work roll diameter). Concerning thick plate, it is of interest to achieve both similar deformation and L/h ratio (L=arc of contact, h=mean gauge) per pass as the industrial schedule because they are simultaneously involved in damage evolution and void closure during hot forming processes (Saby, 2014)."

Jan 1, 2018

By Y. X. Li, L. R. Xiao, S. Gong, S. S. He

Porous copper and porous copper based alloys with controllable pore structure have been manufactured successfully by sintering evaporation process. This process consisted of mixing copper or copper based alloys with NaCl powders, hot pressing and final high-temperature sintering to evaporate the filler material of NaCl powders. NaCl was eliminated completely during vacuum sintering, and strong metallurgical bonding in the walls was achieved. The pores’ structural parameter (pore size, shape, and direction) and porosity can be controlled effectively. These porous copper and porous copper based alloys with controllable pore structure have great potential in many fields. Including heat dissipating materials, heat absorbing materials, chemical catalyst carriers, electromagnetic shielding materials, filtering materials, damping materials, silencing materials, battery electrode materials. INTRODUCTION The development of porous materials began in the 1960s. The research of activated carbon with high specific surface area made porous materials enter the stage of material research (Belyakov et al., 2008; Ferey et al., 2008). With the rapid development of science and technology, porous materials play an important role in material research, and gradually become an indispensable part of the material research field (Wu et al., 2012). The research of porous materials has gradually extended to metal, ceramics, plastics and glass and other fields. It has been successfully applied in many fields, such as functional materials, industrial production, aviation, medical materials, biochemistry and electronics, which fully shows that porous materials have considerable development prospects. Porous silicon, plastic porous materials and glass porous materials are the most widely used in the field of non-metallic porous materials (Capelle et al., 2012). Compared with non-metallic porous materials, metal porous materials have developed rapidly in the late 1980s and become new materials with good mechanical properties and excellent physical properties. Porous metal materials have many advantages, such as large specific surface, small specific gravity, good silencing effect, high stiffness, high electromagnetic shielding performance, good shock absorption performance, etc (Li et al., 1999; Ferey et al., 2008). Among its many applications, metal porous materials can be used as both functional materials and structural materials. In some cases, metal porous materials have dual functions and structures. It is a multi-purpose engineering material with excellent performance. At present, porous copper, porous aluminium and porous nickel are the most concerned materials (Chen et al., 2002; Yang et al., 2017; Liu et al., 2018). The preparation methods of porous copper and copper-based alloys mainly include self-propagating high temperature synthesis (SHS), capsule-free hot isostatic pressing (CF-HIP), spark plasma sintering (SPS) (Kvanin et al., 2008; Takahashi et al., 2008; Zhang et al., 2014). However, these methods can not accurately control pore structure parameters (including pore size, shape, orientation, distribution, etc.). In porous materials, pore structure plays an important role in the overall performance of materials. In order to control pore structure parameters accurately and optimize material performance, it is necessary to explore and develop new preparation technology. In this paper, the sintering evaporation process (SEP) was introduced for the preparation of porous copper and copper-based alloys. The core process of the preparation method is hot pressing and evaporative desalination. Hot pressing can make the pore orientation consistent. Evaporative desalination can ensure the complete removal of NaCl in the form of vapor in a short time, thus eliminating the corrosion of residual NaCl on the matrix metal (Gong et al., 2011).

Jan 1, 2019

By Charles Camsell

Few persons ever stop to consider how vital an influence minerals, and especially metals, have had upon human history, how they have affected the every-day life of the individual or how at different periods they have altered the course of nations and determined their progress. Students and writers of history have dealt very fully with political history and have given us a great deal of detail about the careers and policies of kings, parliaments and nations, but frequently have not touched the economic causes that have been the real forces influencing the development and carrying out of these policies. So far as minerals are concerned there is no single work from which one can get a concise and consecutive account of the growth in the use of minerals, nor of the diverse ways in which the. geographical distribution, the .search for, the development and the use of mineral resources have affected human progress from the beginning of man's history. The reason for this is quite plain, and when one takes a little time to think of it he begins to appreciate the magnitude of the job and he will realize that the story of minerals and mineral resources touches a tremendous range of human activity, not only of mining .and metallurgy, but the whole field of agricultural and industrial growth, of exploration and colonization, transportation and commerce, monetary system, commercial policy, in short, almost every phase of economic life.

Jan 1, 1926

By J. M. Houston

"In October 1982, Rio Algom Limited, purchased a tin prospect near East Kemptville, Nova Scotia, from Shell Canada Resources. This purchase led to the development of the first substantial tin mine in North America. This paper deals with the drillingand blasting operations at Rio Algom, in particular the use of emulsion explosives technology.This presentation describes what emulsion explosives and Heavy AN/FO are, and the support system used to deliver these products to the blast site.HistoryThe East Kemptville mine site was discovered by Shell Canada Resources (SCR) in July 1978. SCR started diamond drilling on the tin prospect in March 1979. After 8220 m of BQ drilling, it was estimated a reserve of 56 000 000 tonnes of 0.165% Sn was present.The property, which is located 54 km northeast of Yarmouth, Nova Scotia (Fig. 1), showed, after a feasibility study that, given an ore treatment rate of 9000 tonnes per day, a mine life of 17 years could be expected.GeologyThe tin deposit of the East Kemptville Mine, occurs in granitic rocks at their contact with metasedimentary rocks. The mineralization is in the form of cassiterite with associated sulphides of copper and zinc. The tin occurs in a stockwork of tin bearing Greisen alteration zones.East Kemptville MineThe mine planned an open pit operation with the first five years being mined at a rate of 14 000 tonnes per day, of which 5000 tonnes will be waste and low grade ore. Eventually, the total mining rate will be 21 000 tonnes per day, including 12 000 tonnes of waste and low grade ore. Figure 2 shows the general layout of the mine site.East Kemptville Chooses Emulsion ExplosivesIn December 1984, East Kemptville Mine awarded the Explosives Division of C-I-L Inc. a contract to supply explosives to the borehole. The system chosen gives East Kemptville the on-the-bench choice of regular AN/Fa, or a high density, Heavy AN /Fa product called SuperAN· or a water resistant emulsion explosive called MAGNAFRAC· for holes that cannot be dewatered.Emulsion ExplosivesAn emulsion is an intimate mixture of two liquids that do not dissolve in each other. Emulsions have contributed to our daily lives in such products as insecticides, salad dressings and cosmetics."

Jan 1, 1987

By Jean-François Dorion

In an underground mine rock reinforcement elements and surface support units are often exposed to conditions that make them susceptible to corrosion. These unfavourable conditions include high relative humidity, the presence of dust and various other particles in the atmosphere, splashing of water and gases from blasting and diesel equipment. The corrosion of support systems is often associated with a loss in capacity that can be a major safety and economic concern in underground mines. A support system is composed of several components such as bolts, mesh, plate, retaining nut, cable ties. Every individual component can deteriorate due to atmospheric or aqueous corrosion and consequently can damage the integrity of the support system. This paper reports the results of a 5-yr study on the loss in capacity of individual support and reinforcement components at selected underground hard rock mines. As part of this investigation corrosion coupons were installed at selected locations at participating mines. A number of these coupons were recovered at regular time intervals and analysed for any signs of corrosion and subsequently tested to quantify any loss in capacity. The testing of the corrosion coupons was complemented by similar tests on recovered mesh and friction bolt specimens from the site. The collected data have provided useful insights on the factors that contribute to the corrosion of support systems. This knowledge can aid in the selection of appropriate support strategies and a reliable assessment of the predicted useful life of a support system and the need for rehabilitation.

Jun 1, 2012

By G. R. Tostengard

"The paper identifies functional areas which frequently can yield significant productivity improvement. Emphasis is placed on the repair and maintenance, material supply and training functions. Successful approaches are discussed in some detail, and typical results which have been achieved are reviewed.IntroductionA challenge which at all times confronts the manager o f any mineral operation is the potential to improve his operation no matter how effective it might be a t the present time. The challenge has been present through my entire lifetime and I suspect a good many years prior to that and, I expect, will continue many year s and decades in the future. The competitive and economic situation in which we in the minerals industry find ourselves today makes the challenge eve n more important during the 1980s. In many cases it’s a question of survival, not simply pr of it improvement.There are, of course, many avenues to improving profitability; technological changes, new equipment and facilities, improved products, improved mine plans, etc. All of these are important and must be addressed by each manager. This paper focusses on just one avenue to improvement and that is ""improved management"", not so much of management at the boardroom level but of improved management o f the facilities and workforce as the y currently exist. Management implies control. There are three areas where control is often found lacking:1, Repair and maintenance of equipment and facilities;2. Material supply including procurement, inventory control and warehousing; and3. Training.These three areas are all complex and difficult to manage and they are all but ignored in the formal education which our industry's manager s normally receive. They are areas which can be improved with relatively small investments and therefore, they represent especially attractive improvement targets during the 80s when, for most of us, investment dollars are very difficult to come by."

Jan 1, 1983