Search Documents

By L. D. Haig

"The Texada Mill is a unique iron operation producing High Grade sinter iron concentrate and a by-product copper, gold, silver concentrate. The plant is complex and extremely flexible to handle the many varieties of ore. Two iron concentrates are made and blended. A coarse iron concentrate from primary grinding and a fine concentrate after rougher flotation to remove all the sulphides.All the tailings from iron processing are collected, dewatered, reground and floated for additional copper recovery.The entire milling operation has been carried out in all sea water for seven years and mixtures of sea, fresh, and reclaimed water for ten years prior to that.A very stable float results from the use of sea water at the natural pH8. Reagent Consumption is lower and Metallic Corrosion of mill liners and grinding media is actually less than local fresh water or mixtures of fresh and sea water.Marine growth in pipe lines can be periodically removed by violently bubbling high pressure air up through the water filled mains.Location:Texada Mines is located on tide water on the west side of Texada Island 100 miles northwest of Vancouver, B. C.The Island is served by a 30 car ferry, tug and barge and a scheduled air service from Vancouver to a company maintained air strip near the mine.The climate is moderate with about 30 inches of rain during the winter and relatively dry summers."

Jan 1, 1974

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The hydrotransport systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1,500-2,000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed and installed at Aurora, incorporating significantly increased impeller diameter and pumping vane lengths. The new pumps are expected to triple Aurora’s previous mission length for hydrotransport pumps. Part II of this paper will share actual hydraulic and wear performance observed in the first several months of operation, and draw comparisons relative to what was expected for these pumps in design / development.INTRODUCTION Slurry Pumps are Critical Equipment at Syncrude Slurry pumps are a key component in Syncrude’s operations. In a typical Aurora application, each 5000 HP pump stage helps move over 8,000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1,500 to 2,000 hours, or 12 to 16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in unduly high impeller vane leading edge speeds for the service conditions."

Jan 1, 2014

By James K. B. Booth

The natural crustal abundances of the principle metals of commerce are examined in relation to production and prices for each metal. Two factors, the abundance x price ratio (BP factor) and abundance/production (B/T factor) are listed for each metal. Ideally, for these desirable commercial metals, each factor should be a constant and the same for all metals; comparing the divergences for the full list of metals allows conclusions to be drawn on the relative degree of natural availability of each metal and the ease or difficulty of winning the metal from the earth's crust. Plotting the two factors for each metal over the past decade of steady industrial usage illustrates the anomalous position of copper and, to a lesser degree, molybdenum and it is concluded that over the long term the price of copper will continue to rise steeply. Possible future prices for copper are examined and a suggested preferred order of ranking of the metals as exploration targets would be copper, nickel, tin, zinc, silver, molybdenum and lead, for the near term, with molybdenum possibly increasing its ranking in the list within the next decade.

Jan 1, 1971

By E. A. Lowe, J. W. Smith, C. W. Overton

"The operations of Bethlehem Copper are situated in the south-central interior of British Columbia at an elevation of 4900 feet above sea level. Main road and rail transportation systems pass through Ashcroft in the Thompson Valley, which is 28 miles by road from the minesite. The operation was the first low-grade open-pit porphyry copper mine in British Columbia.The minerals are chiefly chalcopytite and bornite, while the rock is principally feldspar and quartz. In the outer fringes of the orebodies some pyrite is present. Average grade of mill feed is 0.55% copper.History of Milling Operations Production commenced in December 1962 at a rate of 3,000 tpd in a plant that comprised two-stage crushing followed by rod and ball milling. Production ratings were increased to 6,000, 10,000 and 12,000 tpd by the addition of a further stage of crushing and more rod and ball mills. When the last expansion was completed tonnage throughput exceeded the 12,000 ton designed rate and was stabilized at 15,500 tpd.However, recovery did not meet expectations at the expanded rate because of coarse flotation feed. Capacity in the rod mill circuits exceeded the subsequent fine grinding capacity, resulting in poor liberation. Studies were initiated to improve recovery without decreasing throughput.Description of Operation Prior to Pebble Milling Crushing with primary, secondary and a closed tertiary stage proceeds at a scheduled 20.5 shifts per week. Fine ore screened on 1/2"" x 4"" apertures is stored in a 30,000-ton bin ahead of two 12.5' x 15' rod mills. Rod mill discharge joins secondary ball mill (one 10.5' x 14' and one 11' x 14') discharge for classification in a single 50"" cyclone which closes the secondary mills. Overflow from this cyclone is split between three third-stage ball mill-pump-cyclone circuits (two 11' x 14' and one 12.5' x 15'). Prior to addition of the two pebble mills the flotation feed was produced by this three-stage grinding system. Grinding criteria are shown in Table I."

Jan 1, 1975

By F. C. Lendrum

"This paper had its origin in a panel discussion organized by the Canadian Uranium Producers Metallurgical Committee (CUPMC) at their Annual Meeting in Blind River in May, 1964. The reason for the panel was the formation of the National Uranium Tailings Research Program funded in the amount of ten million dollars by the Federal government. According to the bureaucrats in charge the program would seek to solve the perceived problems as well as any actual problems they believed existed with uranium tailings. Dr. Allan Ashbrook of Eldorado Nuclear chaired this panel and his summation of the panel's purpose was set out as ""Regulation and the Regulatory Process in the Nuclear Industry, Where Have We Been, Where Are We Now and Where Are We Going""?"" This paper will try to relate these questions to the whole mineral industry.The Canadian Mining Association has been telling us our natural resources are today required only if they are competitively priced with those produced in so called ""third world"" countries where labour rates are lower, environmental restrictions may be less and every effort is made by the local government to sell their product. It is in this hostile economic climate that the Canadian mining industry now finds itself. Before going further I want to stress these comments apply only to: a) Mines financed by private capital in a free enterprise society.b) Mining companies want to operate in an environmentally safe manner. However, they must earn a profit because no company financed with private capital can borrow money ad infinitum.WHERE HAVE WE BEENNone of us today would want to return to the days when the mill waste management system consisted of pumping the tailing to the nearest slope and letting nature's law of gravity do the rest. This was the way it was in early gold mines in Nova Scotia, tin mines in Cornwall, England or silver mines in Cobalt, Ontario and survives today in countries where climate, customs and methods of doing business are far different from Canada. As mill tonnage rates increased, more sophisticated systems evolved often designed for mining areas with different climates. Systems imported from arid climates such as south-west United States retained the solids but allowed bacterial oxidation of the sulphides promoting acid drainage. Environmental regulations were introduced and Canadian mines learned to handle tailings in our climates."

Jan 1, 1986

By Mark Holdsworth

In 2002, Kennecott Utah Copper Copperton Concentrator installed an Expert Control system for optimization of their SAG and Ball milling circuits. The advanced process control has been well received and is utilized well over 95% of the time. In the years since, many lessons have been learned and many advances have been made. Improvements have produced millions of dollars of benefits and have included directly controlling feedrate with complex logic as opposed to using a bearing pressure controller, modifications to how sound is used for control, modifying logic for maximizing asset utilization and using advanced control for automating equipment restart.

Jan 1, 2012

By D. Royston

Reducing SAG Mill feed size has been a major trend in recent years. ‘Mine to mill’ strategies have reduced blasted-rock size, and in a growing number of operations reducing the primary crusher CSS and/or adding additional crushing upstream of the SAG mill have reduced rock feed size. While reducing feed size will increase SAG mill throughput, issues arise in terms of retaining charge in the mill, exposing the shell lining to impact damage, and maintaining milling performance should the pre-crush system shut down. This paper reviews the past experience on pre-crushing for SAG mills and provides an analysis of liner design (in particular grates and shell liners) for pre-crushed feed.

Jan 1, 2012

By C. George Miller

"As the influence of governments has become more widely felt, the use of research techniques to analyze policy has increased. Mineral economics, as one of the foundations of mineral policy research, has grown accordingly. Policy research and analysis has been carried out within governments, university departments and the private sector. Each of these institutional environments has characteristics which influence the topics of study, the approach, the methodology and the output of the research. A brief survey of recent research activities provides illustrations of trends and developments occurring within this organizational framework.A radically different organization, the independent research institute, has begun to make an impact on policy research in recent years, and will have an increasing importance in the future. Combining certain features of the traditional research organizations, it nevertheless has important differences which are essential to its effective functioning. An overview of the formation, goals, organization and operation of one such institute is presented."

Jan 1, 1976

By Noel W. Kirshenbaum

Difficulties and costs of transport markedly affect Canadian mineral producers because of distance from markets, weather conditions and rugged terrain. The chemical and physical nature of sulphide concentrates presents additional difficulties in handling and transport, resulting in higher costs which are ultimately borne by the mineowner. Troublesome properties include the thixo-tropic character of wet concentrates, freezing, susceptibility to autogenous heating, and fine particle size causing spillage and dusting losses. Canadian mineowners and shippers must contend with these problems and with stringent regulations governing the maritime shipping of concentrates. A "systems approach," in which complementary techniques in materials preparation, handling and transport are integrated, could reduce freight costs and losses for those selling concentrates, facilitate operations for those carrying and handling them and, in some cases, improve metallurgical processes in smelters receiving them.

Jan 1, 1969

By M J. Daniel

Comminution is the science of size reduction of brittle materials. It is integral to mineral extraction and is one of the most energy intensive processes in the mining industry. There are a number of tests used to quantify the strength of ore, which are then used to size the AG / SAG mill in circuit design. The calculated energy utilized for breakage in these devices is based on the assumptions that the materials treated are of average shape and that the processing equipment is designed to break the ore as efficiently as possible under the given operating conditions. In drop weight tests, it was found that shape significantly influences the measured rock strength. Controlled experiments with variations in blends of rock shape show that mill throughput increases with the addition of weaker shaped rocks.

Jan 1, 2012

By Candido Bariáin

A new vapochromic material of formula [Au2Ag2(C6F5)4(bipy)2]n (bipy = 2,2´ bipyridine) has been developed and used for the detection of some volatile organic compounds as acetone either in vapour or in water solution. The material is presented in the form of powders which colour changes with acetone vapours turning from bright yellow in the absence of vapour to white in the presence of vapour. By using the sol-gel technique, the powder ? dispersed in tetraethyl orthosilicate- was easily deposited on optical fibres. In order to study experimentally the behaviour of this material for construction practical optical fibre sensors, a sol-gel material doped with the vapochromic material is deposited onto an extreme of a monomode fibre connected to a coupler. The behaviour of the material was studied for different wavelengths and concentrations of acetone vapours and acetone/water solutions. Changes up to 4dB in the reflected optical power were detected. Optical fibre sensors have many advantages over conventional ones, such as electromagnetic interference immunity, passivity behaviour, possibility of using multiplexation techniques, low weigh and little size, etc. Actually, there is an increasing interest in developing optical fibre sensor for vapour detection in the chemical industry and in fact many sensor had been developed [1]. Some are based on the deposition of a sol-gel-based material either over the core of an optical fibre [1] or onto the thinner zone of a biconically tapered optical fibre [2]. Others are based on Fabry-Perot interferometers [3]. Also there are sensors based on the reflection of the light on films, on the fluorescence of dye-doped polymer cladding in fibre, on colorimetric reagents in the core of a silica fibre or on surface plasmon [4]. The possible materials for the construction of such sensor should be colorimetric reagents able to change the colour or refractive index in the presence of same organic vapours. There are not many metallic complexes with these properties, although same interesting examples have been reported in the chemistry of palladium and platinum as [Pt(p-R-C6H4NC)4][Pd(CN)4] described by Nagel [5] and Mann [6], which reported the construction of some LEDs. We recently reported the preparation of a novel vapochromic material (Fig 1) [7] which can be used for the construction of optical fibre tapered environmental sensors [8,9] of vapour organic compounds (VOC´s). Also we reported other nickel and palladium derivatives which present this type of behaviour [10]

Oct 1, 2003

By Kish. L.

"The results of a chemical and mineralogical study of eighteen opaque-oxide occurrences are discussed and the detailed chemical, metallurgical and mining feasibility study of a vanadium-rich magnetite deposit is summarized. A plot of the mol-percentages in the system FeO- Fe2O 3-TiO2 indicates that the deposits fall into two distinct groups: some contain hematite with ilmenite, and some others have magnetite with ilmenite (titaniferous magnetites). The plot also suggests that the two types of deposits were crystallized from liquids of different compositions. Each group has its distinct structural features. Vanadium is present in all of the studied specimens, however concentrations of economic importance have so far been found only in the titaniferous magnetite deposits. The vanadium content of the oxide concentrations of the Dore Lake Complex is the largest among the studied occurrences. Analyses of the concentrates of the drill-core sections show a compositional variation across the orebody; a continuous increase in the tenor of Ti02 and a decrease in the vanadium content upward in the layered sequence is found. Concentration tests on several tons of samples indicate that about 80 per cent of the vanadium is recovered in the magnetite concentrate."

Jan 1, 1972

By J. C. Kurnia

Presence of fine dust in air causes serious health hazard for mine operators resulting in such serious problems as coal workers? pneumoconiosis and silicosis. Major sources of dust appear of course along the mining face where the minerals are extracted. Proper control and management are required to ensure safe working environment in the mine. Presented here is the use of a computational fluid dynamic (CFD) approach to investigate the flow and dust behaviour in mining tunnels. The objective of this study is to propose and examine various strategies to mitigate dust dispersion from the mining face and reduce dust concentration to a safe level for the operator. In a companion study, the authors investigated various methods for mitigating dust dispersion from the mining face to ensure safe dust concentration levels in the mine tunnel. Among the examined methods, implementation of brattice to direct the flow from the main airway to the mining face is the most effective method to disperse dust particles away from the mining face. The installation of brattice, however, will limit the movement of mine operators and vehicles in the tunnel. Hence, application of a hybrid brattice which is a combination of a physical brattice along with suitable directed and located air curtains is proposed and examined. Based on the CFD simulation results, over a range of parameters of interest, it was found that the physical brattice blocks the ventilation air and directs it to the mine face while an air curtain located along the brattice outlet offers flexibility in keeping the dust away from the operator allowing more freedom for the operator and the equipment. Results of the modelling over a range of parameters of interest are presented and discussed with the goal of managing dust concentrations within safe limits for the operator.

Aug 1, 2013

By C. M. Bartley

Fluorspar, in addition to its familiar uses as a metallurgical flux and as a source of the electrolyte for aluminum production, has become important as an essential raw material in the rapidly growing fluorine chemical industry. The unique ability of fluorine to react and form compounds with al-most all other chemicals has made it one of the important elements in modern chemistry. Research and development over the past thirty years have resulted in a current annual production of fluorine chemicals that is both technically and economically important to industry. Because many of these chemicals and products are relatively new, and most have properties that are not duplicated by other materials, the present uses are expanding rapidly and new applications are being reported continually. Fluorspar, the only immediate and practical source of fluorine, is therefore an important mineral. This fact has been recognized in major industrial areas such as the United States and Western Europe, but has received little attention in Canada.

Jan 1, 1962

By R. P. D. Graham

It is almost exactly two hundred years since the foundations of the mining and metallurgical industries in Canada were laid. There '."'as nothing spectacular about this early start. It had to do with the most basic phases of these industries-the mining of coal and iron ore, and the manufacture of cast and wrought iron. At several points along the coast of Cape Breton island, coal seams may be seen outcropping quite conspicuously, and it is probable that they had been observed, and possibly worked in a small way, in very early times. However that may be, these coal seams have the distinction of being the first in North America of which there is any printed record, reference to them appearing in a volume by Nicolas Denys which was published in Paris in 1672. Regular coal mining in the district did not commence until about fifty years later, however. The metallurgists started their operations along the north shore of the St. Lawrence river. Here, at many points between Montreal and Quebec, are to be found deposits of bog iron ore, and in 1 730 a furnace for smelting such ore was established on the St. Maurice river. The St. Maurice forges continued in operation until 1880, and throughout that long period they were famed for the fine quality of castings produced, and also for a-superior wrought iron.

Jan 1, 1924

By L. S. Beck

"The Athabasca region forms part of the Churchill province of the Canadian Shield and is underlain by an Archean or Aphebian assemblage of rocks that underwent severe metamorphism and granitization during the Hudsonian orogeny (1750-1950 m.y. ago). In places, the eroded orogen is overlain by unmetamorphosed cover rocks (in-cluding the Martin and Athabasca formations) of probable Paleohelikian age. Basic dykes cut all the rocks of the region.There are innumerable vein-type pitchblende deposits and many syngenetic occurrences of uraninite in crystalline basement rocks. Evidence is presented to show that pitch-blende was emplaced during the final stages of the Hud-sonian granitization and followed the crystallization of syngenetic uraninite transitionally. In terms of P-T condi-tions, the pitchblende deposits belong essentially to Lindgren's mesothermal group.Based on the postulated uranium metallogenesis, the possibilities of finding further deposits of pitchblende and other types of uranium deposits are discussed."

Jan 1, 1970

By A. Ouchi

This paper presents ground control best practices in weak rock environments including the "Unsupported" Weak Rock Updated Span Design Curve and awareness pertaining to the potentially detrimental effects of using resin grouted rebar in weak rock masses and the false sense of security that the use of resin grouted rebar may instill. Ground support is almost always used in weak rock environments, though the type of support used can vary widely. The development of the Weak Rock Updated Span Design Curve by the addition of 463 case histories of RMR76 values ranging from 25 to 60, has also been calibrated to four different support categories; Category A: Pattern Friction Sets, Category B: Pattern Friction Sets with Spot Bolting of Rebar, Category C: Pattern Friction Sets with Pattern Rebar Bolts and Category D: Cablebolting, Shotcrete, Spiling, Timber Sets or Underhand Cut and Fill. Design of underground man-entry type excavations in North America relies heavily upon empirical analysis. This design requires a higher Factor of Safety than other non-man entry type excavations. A comparison of the calculated ½ span failure Factor of Safety between all the categories is also presented.

May 1, 2009

By Flavio Rojos-Tapia, Samuel Sánchez-Pino, Marcelo Fernández-García, Samuel Sánchez-Baquedano, Rainer M. Imhof

"Pneumatic flotation was introduced to the Chilean copper mining industry in 1993 by Ingeniería de Minerales S.A., being implementation in 1994/95. The technology is based on the designs and development of Dr. Rainer Imhof from Germany and from Chilean copper processing experience.Pneumatic flotation has been successfully used for sulphide and oxide copper minerals and copper slag, iron ores (reverse flotation), gold and promising results with molybdenum as product. Extremely hard conditions were applied in flotation process such as roughing, cleaning, scavenging. Pneumatic flotation can be applied for any type of mineral which has to be separated by flotation. Even very dense and heavy slurries can be processed, the range of the particle sizes to be collected is very wide, and the number of cleaning stages needed normally is one in our experience until now.The good performance of the technique can be explained by the high gas hold-up and the very effective micro-turbulences which boosts the attachment to the bubbles changing dramatically the flotation time concept. Some economic high lights are: less energy consumption, less maintenance costs, simple and reliable to operate and it is required a small area to install the circuits.As a result of the Chilean mining industry experience, it can be concluded that the pneumatic flotation can be regarded as an excellent alternative to the conventional way of Mineral Processing.INTRODUCTIONDerived from seventies, works in Germany about pneumatic flotation with Prof. Simonis (Technical University of Berlin) and Prof. Bahr (Technical University of Clausthal), it has been developed an interesting flotation technology in Mineral Processing, with the designs developed by Dr. Rainer Imhof, who has been known for more than ten years (Imhof, 1998) by his contribution at Ekof, KHD, Allmineral and the actual company Maelgwyn Mineral Services where he is a Technical Director. Ingeniería de Minerales S.A. has been working ten years deeply involved with the technology developed by Dr. Imhof and is more than ten years experienced with pneumatic flotation, from Wits University and Mintek in South Africa (Sánchez, 1990), (Sánchez, 1990)."

Jan 1, 2003

By J. Lazareck

"XPotential Products Inc. has developed technologies to convert auto shredder residues and other forms of plastic waste into useful products such as posts suitable for retaining walls and parking curbs. The technology is competitive provided low-cost plastic waste is available, and could have applications throughout the world. The paper describes the technology used and illustrates the various processing steps. Development of the TechnologyPresently, state-of-the-art auto shredding yields approximately 75% ferrous and non-ferrous metals and approximately 25% by weight of auto shredder residue (ASR). Advances in metal shredding and non-ferrous metal separation technologies turned XPotential Products Inc.’s attention to ASR as a potential revenue source, or at least a means to markedly reduce the cost of disposal. This abundance of nuisance ASR was, in the company’s view, a potential resource as derelict autos and white goods were similarly perceived 40 years ago. As owners of General Scrap & Car Shredder Ltd. in western Canada, XPotential faced significant disposal costs for four shredders. This journey began over 10 years ago and took many twists and turns until a final course of action was chosen. The recovery of the metallic portion of vehicles and white goods has reached technological maturity and attempts to add value are now achievable only in very small increments."

Jan 1, 2004

By M. Pekguleryuz, S. A. Argyropoulos

"The recovery of additions in light metals is an important parameter influencing consistency of the finished product, which ultimately means cost. Recovery is a function of many parameters such as assimilation speed, addition density, addition practice, liquid metal processing conditions, etc. In liquid metal processing operations, it is desirable to have the maximum possible recovery at the shortest possible time.In this paper a new index will be presented, namely, the rate of recovery (RR). This index quantifies the addition recovery and introduces the time dimension in the recovery increase. As such, the RR equips the liquid metal practitioner with an accurate picture of addition assimilation in liquid metals. Results will be presented on how this index is applied to a variety of additions in liquid aluminum. IntroductionThe data on addition assimilation kinetics offer a valuable parameter describing how fast a given addition enters the metal bath. These data may be expressed as gr m-2 s-1 of additive for a set of experimental conditions which might include bath temperature and degree of bath agitation among others. However, the liquid metal processing practitioner is more interested in the recovery of additions. In other words, the point of interest is the percentage of the used addition entering the metal bath. Ideally, the addition recovery can reach the 100% level. However, in practice, the addition recovery never or rarely reaches that level. Many factors can contribute to this. Some of these factors can be slow assimilation kinetics, addition density, addition practice, turbulence of the melt, etc. In some cases, sloppy addition practices can contribute to low recoveries, or even worse, to erratic recoveries.In this paper a new parameter is introduced. This parameter relates the maximum addition recovery observed over the time needed to achieve this maximum recovery."

Jan 1, 2002