Search Documents

By F. H. Samuel, A. M. Samuel, H. R. Ammar

Casting imperfections, such as porosity, in cast aluminum components greatly influence their fatigue properties. The effect of porosity on the fatigue life of 319-F and A356-T6 aluminum alloys was studied, where the porosity characteristics on the fracture surfaces of fatigue-tested samples were examined using SEM and image analysis. The results show that porosity has the most detrimental effect on the fatigue life: 92 % of all tested samples fractured due to porosity acting as the main crack initiation site. In the absence of casting imperfections, other microstructural aspects such as slip bands can be responsible ( 4 % ). The porosity was investigated in terms of the pore size at the sample fracture surface and its location i.e. near the edge or close to the interior. It was found that porosity located far from the sample surface (edge) has less influence on the fatigue crack initiation, and the fatigue life decreases as the size of the pore located at the sample surface increases. Aluminium

Jan 1, 2006

By M. Rafieazad, P. Fathi, X. Duan, M. Mohammadi, A. M. Nasiri

"Direct metal laser sintering (DMLS) is a metal additive manufacturing technology that creates highly complex components by fusing metal powder into a solid part. In this study, the impact of surface roughness on corrosion resistivity of AlSi10Mg_200C alloy manufactured through DMLS was investigated. The as-printed DMLS-AlSi10Mg _200C alloy was subjected to various surface finishing processes including grinding and sandblasting. The corrosion performance of the surfaces was then evaluated using potentiodynamic polarization testing and electrochemical impedance spectroscopy (EIS) in a 3.5 wt.% NaCl solution to mimic seawater environment. Surface characterization and corrosion morphology of the samples were assessed by Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) spectroscopy. The results of this study show that the surface finishing process and the resultant surface roughness has a significant impact on the corrosion resistivity of the DMLS-AlSi10Mg_200C alloy in the seawater environment.INTRODUCTION Direct Metal Laser Sintering (DMLS), also known as Selective Laser Melting (SLM) (Sames, List, Pannala, Dehoff, & Babu, 2016), Laser Beam Melting (LBM), or Laser Metal Fusion (LMF) (Herzog, Seyda, Wycisk, & Emmelmann, 2016), is an additive manufacturing process that utilizes a precise, high-power laser to micro-join powdered metals and alloys layer by layer to form almost fully dense and functional components in three dimensions from the 3D computer-aided design (CAD) data. Complex geometries not possible with conventional manufacturing processes can be readily manufactured with high accuracy using the DMLS process with no need to time-consuming tooling."

Jan 1, 2018

By S. M. Bulataovic, D. M. Wyslouzil

"The Martison Lake phosphate-niobium deposit is composed of unconsolidated residuum containing clay and silt-size particles of phosphate, niobium, iron and clay minerals. This paper deals with the laboratory and pilot plant development of the flowsheet and the reagent scheme to treat the Martison Lake ore. The ore, in addition to the complex gangue composition, contained several phosphate minerals including fluorapatite, francolite and florencite. The detailed laboratory and pilot plant evaluation resulted in the development of an effective flowsheet and reagent scheme for the selective flotation of phosphate minerals using a fatty acid circuit, followed by niobium flotation using amine collectors at acid pH. The developed flowsheet included des liming of ore, magnetic separation, and selective P 2 O 5 -Nb 2Os flotation. The main aspects discussed include characterization of the ore, step by step development of flowsheet and evaluation of dfferent modifiers and collectors for P20s and Nb20s flotation.INTRODUCTIONMartison Lake phosphate-niobium ore deposit, located 75 km north of Hearst, Ontario was discovered in the early 70's and has been the subject of extensive technical-economic evaluation in the late 70's and early 80's.The deposit is covered completely by 30 m to 90 m of glacial overburden and is composed entirely of unconso1idated material called residuum, that lies on top of a precambrian age carbonatite intrusive from which the residuum was derived by weathering and natural leaching in situ. The residuum is and irregularly-shaped horizontal lens, 2 km by 3 km in area, and up to 100 m thick, composed mostly of unconsolidated clay and silt-size particles of phosphate, niobium, iron, mica and clay minerals."

Jan 1, 1986

By Weng Fu, James Vaughan, Stefan Lakemond

Uranium bearing copper sulphide flotation concentrates produced from iron oxide copper gold uranium (IOCG–U) ore contains radionuclides such as 238U, 230Th, 210Pb, 226Ra, 210Po, which have the potential to reduce their marketability, thus posing a challenge to the industry. Thus, a two–stage leach process has been proposed in this study. In first stage, a sulphuric acid leach process effectively dissolve most of the 238U and 230Th into solution, but other radionulclides (mainly 210Pb, 226Ra and 210Po) remain associated with copper sulphide minerals owing to their low solubilities in sulphuric acid solution. In the second leaching stage, the use of methanesulfonic acid (MSA, CH3SO3H) is investigated to selectively dissolve the 210Pb, 226Ra and 210Po from the residue of the first stage. The results indicate that 96% of 238U, 87% of 230Th, 90% of 210Pb, 86% of 226Ra and 17% of 210Po are dissolved using 3 mol/L MSA solution at 90°C for 3 hours, which represents a dramatic decrease in the radioactivity of the copper concentrate. INTRODUCTION Australia is host to one of the largest iron oxide copper–gold–uranium (IOCG–U) deposits in the world. Most of the value in these deposits is associated with copper. In mineral processing, the gangue minerals are separated from copper sulphide minerals that report to a copper flotation concentrate. However, due to the strong association of uranium with copper minerals and hematite, even clean copper concentrates can contain significant amounts of uranium (238U) and its radioactive decay elements, of which thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) are the long life radionuclides. These hazardous radionuclides negatively affect the marketability of the copper concentrates. Customer copper smelters in China, Japan and Europe may consider the radionuclides penalty elements or may not be able to process the feed. Therefore, there is a strong motivation to remove radionuclides from copper concentrates at the mine site before shipping to custom smelters in global market. Hydrometallurgical leaching has been widely employed to remove radionuclides from different kinds of minerals such as copper concentrates (Ragozzini & Sparrow, 1987), zircon concentrates (Aral, Sparrow, McDonald, & Norgate, 2007), and coal ash (Lei, Qi, Sun, Xu, & Wang, 2014). Leaching using sulphuric acid (H2SO4) solutions is the most widely used process for the extraction of uranium from uranium ores due to the relatively low cost and wide availability of the acid (Bhargava et al., 2015; Gilligan & Nikoloski, 2015). The leach process involves treating ground ore slurry with sulphuric acid at elevated temperatures (typically 60–90 °C) under oxidising conditions in order to convert the uranium in the minerals 2+ from the relatively insoluble tetravalent form (UO2) into water–soluble hexavalent state (UO2), which then complexes with SO42- and forms UO2(SO4)22- in solution. The uranium oxidation is generally carried out in the presence of ferric ion (Fe3+), regardless of the reagent and oxidant used. The most commonly used oxidants for uranium include sodium chlorate, pyrolusite and oxygen (Ring, 1980). These oxidants act indirectly by converting ferrous sulphate, formed by the oxidation reaction of UO2 in slurries, into ferric sulphate. The presence of Fe–containing gangue minerals such as hematite in the ore usually provides sufficient Fe required for the oxidation of UO2. After sulphuric acid leaching, the locked thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) elements are chemically liberated from hematite and uranium mineral grains (Ciobanu, Wade, Cook, Schmidt Mumm, & Giles, 2013). However, the extraction rate of radium (226Ra), lead (210Pb), and polonium (210Po) in sulphate solution is very low due to the limited solubilities of (Ra, Pb, Po)SO4 (Bagnall & Freeman, 1956; Liu & Papangelakis, 2006; Nikitin & Tolmachev, 1933).

Jan 1, 2019

By Ish Grewal

The ACACIA Reactor - Introduction What is it? The Acacia Reactor is a fluidized bed high intensity cyanide leaching system. Purpose for its existence? The Acacia Reactor was developed to treat high grade gold concentrates generated from primary gravity concentration systems. Why intensively cyanide leach a gravity concentrate? Current secondary upgrading processes, such as tabling, create significant losses of fine gold that is initially recovered in the primary gravity concentration units. Additional benefits include improved security and a reduction in health hazards associated with calcining.

May 1, 2002

By Greg Rasmussen

"Huckleberry Mines Ltd is an open pit porphyry copper-molybdenum mining operation located 120 km south of Houston, British Columbia with a 18,000 tpd milling facility. Huckleberry Mines is owned 60% by Princeton Mining Corporation, the operator, and 40% by Japanese partners.The Huckleberry deposit is one of several porphyry systems located in the Tahts a district of the intermontane belt of British Columbia. The principal economic minerals are chalcopyrite and molybdenite. The ore deposit is split into two ore deposits, the Main Zone, consisting of24,241,000 tonnes of mineable reserves grading 0.484 %Cu and 0.013 %Mo, and the East Zone, consisting of 66, 131,500 tonnes of mineable reserves grading 0.523 %Cu and 0.014 %Mo.The milling begins with gyratory crushing. This sizes the product down to 100% passing 6 inches. This product is discharged onto a stockpile by a stationary conveyor. The stockpile was designed for a capacity of 144,000 tonnes with a live capacity of 20,000 tonnes. Two apron feeders draw the ore from the bottom of the stockpile and discharge onto a SAG mill feed conveyor which in turn feeds a grinding circuit consisting of one 32' x 15' SAG mill and two 30' x 16.5' ball mills. The grinding cyclone overflow feeds bulk flotation at 55 -65% minus 200 mesh.The bulk flotation uses conventional rougher and column flotation methods to float a bulk concentrate recovering 92.6% copper on the East Zone and 95% copper on the Main Zone with 75% recovery molybdenum on both zones. The bulk concentrate feeds the bulk thickener which produces a density of 60 %solids. This in turn feeds the molybdenum circuit, which separates the copper and molybdenum, by depressing the copper then using conventional rougher and column flotation produces a copper concentrate of 27 %Cu and 0.02 %Mo, and a molybdenum concentrate containing 1.5 %Cu and 54 %Mo at 67% recovery. These concentrates are separately thickened, filtered, dried, and shipped to the smelter for processing."

Jan 1, 1998

By Hans de Ruiter

"Delft University of Technology, RWTH Aachen, Helsinki University of Technology and Imperial College established the Federation of European Mineral Programs (FEMP) in 1999 as a legal body to coordinate joint M.Sc. education.By 2003 the number of participating universities in Europe has grown to 9 (in 7 countries) offering 3 different M.Sc. joint programs. Furthermore students from 8 universities in the USA, Canada, Australia and Chile participate through exchange agreements. About 25 companies are associated with FEMP. Further expansion with other clusters of universities is being investigated.So far some 160 students have taken the programs and are working in all parts of the world in a variety of jobs.The European Commission has recently announced the new “Erasmus World” program that will stimulate the offering of joint programs by European universities and offer third-country students and teachers a greater opportunity for mobility and an enhanced European added value. Host European postgraduate courses will be selected for a five-year period. They will receive funding from the Community and a “EU” seal. Around 250 “EU Masters Courses” will be established.The envisaged new Erasmus program and it’s network and operating practices are very similar to those being used by EMC, EMEC and EGEC. Erasmus World therefore offers a great opportunity for further developments with FEMP as the official body.INTRODUCTIONThe current situation in Europe is that globalisation of the supply of mineral resources has caused the larger mining and the manufacturing companies to expand and invest particularly outside Europe. However these industries still have a great significance for the European Union and its members, which means that mineral engineering know-how is still important in the E.U. It was therefore realised in the mid-nineties that is vital to maintain the very high level of knowledge and skill base in mining engineering and mineral technology that currently exists in the E.U., through good and well-balanced education programs."

Jan 1, 2004

By A. J. Antony Chettupuzha

During a construction project, it is important to ensure that accurate and pertinent knowledge is delivered on time to appropriate personnel. The criticality of documents exchanged or referred to by various parties, evolves over the course of the project lifecycle. Determining the criticality of documents at different stages of the project can aid companies with managing the flow of information in an organized manner, while providing for the detection of potentially disruptive, erroneous material that could result in delays and costs. Therefore, it is crucial to determine documents which have the potential to disrupt a process (by virtue of being incorrect versions etc.) so that they may be isolated or prevented from entering or interfering with the active flow of information in a project, while also ensuring standard revisions of documents are recognized and accessed accordingly. Electronic Product and Process Management [EPPM] systems provide the capability to establish and map information flow between different parties in a construction project. Analyzing an EPPM system may yield information about the criticality of certain documents within an activity, as well as isolate characteristics peculiar to documents which can assist in risk mitigation. We propose methodology that identifies such critical documents.

Aug 1, 2013

By Mark W. Bartlett

Program Objectives ??Identify and implement a tool for haul truck drivers that: -Reduces or eliminates fatigue-related injuries and fatalities -Reduces accidents and equipment damage ??Following evaluation period, apply tool where most effective Why do We Need a Fatigue Monitoring Tool? ??Everyone has probably fallen asleep while driving ??Driver fatigue is a major source of property damage and serious haul truck serious incidents ??To protect ourselves from the other ?tired?driver ??To know when to ask for relief ??To know when we are seriously distracted from driving ??To measure improvements in sleep incidents based on shift changes and intervention ??To help prevent incidents like the following:

May 1, 2011

By S. Amira

The corrosion behavior of high pressure die-cast and thixocast AXJ530 magnesium alloys has been investigated in 0.05M NaC1 solution at pH 6.0 using potentiodynamic polarization tests, electrochemical noise (EN) technique, electro-chemical impedance spectroscopy (EIS) and scanning reference electrode technique (SRET). The behavior of die-cast and thixocast specimens were compared using each of these techniques and the results discussed. Further tests have been carried out with die-cast AZ91D alloy to better compare and interpret the results. Experiments indicate that the thixocast specimens of AXJ530 alloy have a better corrosion resistance than those of die cast alloy in neutral solution.

Jan 1, 2006

By C. Gravel, A. Fathi, P. Rivard, G. Ballivy, Z. Moradian, M. Quirion

Knowing shear mechanism of discontinuities under monotonic and cyclic loading conditions is a key factor in stability analysis of rock slopes and rock foundations. In this paper, the effect of cyclic loads on the shear mechanism of joint asperities is described. For this purpose, a fresh tension-split joint from a granite block was used as a reference and thirty five mortar replicas were fabricated. Cyclic shear tests were conducted on replicas under low values of constant normal load (CNL) using a servo-controlled loading system. Tests were performed in two consecutive steps; load-controlled and then displacementcontrolled. In the load controlled part, after initial increase of shear stress to 0.25 MPa, the test was stopped for 2 minutes, then increased to 0.5 MPa, and finally decreased to 0.25 MPa. This process was repeated ten times. At the end, the test was continued up to 10 mm shear displacement under displacement-controlled loading in order to pass the peak shear strength and reach the residual strength. Characterizing joint surface and modeling of involved asperities during the tests was undertaken using a Matlab code developed with new mathematical expressions. The algorithm used in the code is based on three-dimensional coordinates of the scanned joints’ surfaces before and after the test. It was found that a high percentage of degradation happens during the first cycle of loading and during the other cycles, degradation occurs gradually. While comparing tests conducted in monotonic and cyclic loading conditions, it was observed that under low number of cycles, the pronounced mechanism is consolidation of the joint surfaces. This consolidation increases contact areas and, therefore, shear strength parameters.

Jan 1, 2015

By G. Vibert Douglas

NICKEL minerals are known in New Brunswick but have never been reported from Nova Scotia. The attention of the writers was drawn to an occurrence of pyrrhotite, reported to carry nickel, at the Second Gold brook, Middle river, Cape Breton. The purpose of this paper is to record the occurrence and give an account of the general geological association. In a later paper it may be possible to give greater details? than are available at present. GEOLOGY The area lies at the edge of a plateau of Precambrian rocks which forms the panhandle of Cape Breton island. This plateau has a general elevation of 1,200 feet. Middle river, with its tributaries, the First, Second, and Third Gold brooks drains the area. The lower country to east and southeast of the plateau is underlain by lower Carboniferous sediments. The rocks of the plateau are presumably of Precambrian age but have never been definitely correlated with the Gold-Bearing Series of the mainland. ?There i:s; however, some resemblance, although they have apparently been more intensely mountain-built. They are essentially fine grained, sheared quartzites and slates . The general strike is east and west, with a north dip of 45° to 55°. There are smalllocal drag-folds in the area. The only igneous rock in the immediate vicinity is an intrusive pink porphyry. It has small phenocrysts of quartz and feldspar. It has intruded the sediments generally along the structural planes, but in places crosses the structure . Its intrusive character is further proved by the fact that it contains xenoliths of the quartzite.

Jan 1, 1937

By Robert G. Boutilier

So far, most social performance monitoring systems have not gone beyond listing the impacts on various stakeholders. Executives have had to rely on intuition to devise interventions that would improve the impacts. This paper describes a survey process, known as the Stakeholder 360 (S360), which eliminates much of the guesswork. The paper reviews key studies showing that raising the levels of communication, trust, and common vision among stakeholders leads to the acquisition of the resources needed to improve the socio-economic situation. Therefore, the Stakeholder 360 measures the levels of these three factors in the relationships between a company and its stakeholders, and among the stakeholders themselves. In a validation study at a gold mine in rural Papua New Guinea, the S360 produced a socio-political ?roadmap? that showed management and stakeholders alike which relationships need more communication, trust, or common goals/vision. Management used the findings to create alliances that helped the government move forward on a regulatory regime for the mine closure. The community used the findings to focus its planning for life after the closure. An S360 survey conducted six months later revealed a decline in dependence on the mine and an overall increase in levels of mutual understanding.

May 1, 2002

By G. A. Barclay

"I - INTRODUCTIONSteel castings still comprise the largest volume of wear materials used in crushing and grinding in the Canadian mining industry. The range of impact and wear properties possible with steel castings enables them to be used successfully in both high impact crushing as well as milling where abrasion resistance is the main criterion. Approximately 15,000 tons per year of steel mill liners and crusher castings are used by Canadian mines.The properties of the main steel casting alloys used - manganese, pearlitic chrome-moly and martensitic medium carbon steels will be discussed with reference to their applications. Field data on a new application in primary gyratory crushers for martensitic medium carbon steels is presented. Liner wear life and mill efficiency can be improved through proper liner design.The liner wear pattern can be used as an indication for liner profile changes to improve wear life. Changes in liner configuration can improve through put and use of larger castings can reduce downtime. Casting performance can be improved and foundry production costs reduced by adopting certain design improvements.II - ALLOYS USEDTable I list the most common ferrous liner materials used in relation to their hardness and wear resistance (1). The most wear resistant materials are the irons at the top. In many applications the service impact exceeds the impact strength of the irons and tougher less wear resistant steels must be used. The impact resistance improves from top to bottom with manganese steel the toughest. The hardness of the martensitic steels approaches that of the Ni-Hards however the wear life, because of the absence of carbides, is less."

Jan 1, 1983

By Guoqiang Lan, Jun Song, Bin Ouyang

Rare-earth pyrochlores, commonly exhibiting anomalously low lattice thermal conductivities, are considered as promising topcoat materials for thermal barrier coatings. However the structural origin underlying their low thermal conductivities remain unclear. In the present study, we investigated the phonon properties of a group of RE pyrochlores, Ln2Zr2O7 (Ln = La, Nd, Sm, Gd) employing density functional theory and quasi harmonic approximation. Through the relaxation time approximation (RTA) with Debye model, the thermal conductivities of those RE pyrochlores were predicted, showing good agreement with experimental measurements. The low thermal conductivities of RE pyrochlores were shown to largely come from the interference between the low-lying optical branches and acoustic branches. The structural origin underlying the low-lying optical branches was then clarified.

Jan 1, 2015

By W. H. Hodgson, A. R. Preston

"Improved rail production techniques provide new options for the rail user. Steelmaking improvements offer tighter composition control, lower oxide and sulphide counts, greater control of segregates and freedom from hydrogen problem s. New ultrasonic, laser and eddy current equipment gives printout information on surf ace flatness, straightness and internal condition. These have come along at a time when dramatic changes have occurred on the rail heat treatment scene. Rails can now be deep hardened on or offline in ways which should eventually result in a complete rewrite of the world's specifications. Rails of simple composition can be produced in the hardness range 2801400 BHN as required. The rail user can choose the hardness within this range according to requirement without the necessity for any step changes in the process routes.It is suggested that this is the pattern f or the next decade.IntroductionRails have been the subject of very slow improvement over many years but developments gathered momentum in the early seventies. Recent improvements in quality and properties have provided dramatic increases in rail life under the more severe service situations. Rail profile grinding, lubrication and other track improvements have greatly added to expectations of even longer life. All of this, coupled to even newer mill heat treatment developments, tilt both technical and economic advantages away from tradition to the point where specifications will need to be rewritten so that railroads can take full advantage of these new products."

Jan 1, 1988

By A. Diaz, Minera Los Pelambres, C. G. Salinas, G. Leinenweber, F. Diaz, D. Rojas, R. Bernal, O. Jimenez

"Los Pelambres Mine (MLP) is located in the IV Region of Chile, a semi-arid region where water plays a key role in operations as a scarce resource and is vital for the sustainability of human life, animals and ecosystem. The conventional flow meters installed on pipes at MLP can fail to provide an accurate measurement due to corrosion and/or fouling on the inner wall or presence of elements in the water such as acids, salts and suspended solids. Conventional flow measurement methods require the inner diameter to be known, however it is not always possible to assess its real value due to scaling, fouling, corrosion, etc. Here we present a novel methodology to solve these problems, which consists of the measurement of flow by a method that does not require the internal area of the pipes: the fluorescent tracer dilution method. In addition, the fluid velocity can be determined by the transit time of a radioactive tracer method. With the flow rate and velocity, the equivalent area is determined and thus the equivalent internal pipe diameter as well. This methodology was applied in a recirculation pump station, for mineral processing from the El Mauro tailings dam.This work demonstrated adequate correlation between measurements from fluorescent tracers and velocity measurements from radioactive tracers, both of which lead to the assessment of the internal diameter of pipes with scaling. The results of both methods disagree with the data provided by the flowmeter installed on the line due to its miscalibration. This information is useful in validating and correcting the information provided by online flowmeters of all water and solutions transport processes in filled pipes.INTRODUCTIONPresently, the need to optimize water resources is increasingly ever important, due to various reasons such as water scarcity, community empowerment, an increased use of water for mining processes and environmental considerations. Taking into account those main considerations, Los Pelambres Mine decided to focus on water conservation to avoid losses of this vital element. They decided to demonstrate that all of the systems that used water (flow meters, pipes, pumping stations, lagoons, etc) were in good condition and that no evitable loses of this important resource occurred. A plan was proposed to conduct a “hydraulic assessment” of fluid flux and water speed at different points and courses at the mine, with the purpose of obtaining hard data to support, verify and correct the information provided online from specific instrumentation dedicated to those purposes. The final goal was to manage the water resource basin in a sustainable way, based on cross-checked information. The chosen points are representative of the processes present in the mine, such as recirculating water stations at different operating conditions and surface water courses, where the fresh water capture systems operate."

Jan 1, 2016

By Jacob W. Young

A casual reading of the geological literature extant to-day would give one the impression that carbon is an element which by some chance or another always existed at or near the surface of the earth, and was never of a magmatic origin. The carbonaceous matter in shales is said to be of vegetal derivation; petroleum is stated to have been derived from vegetable matter or from marine animal bodies; if carbon or bituminous matter is found in igneous rocks or associated with metallic ores, the statement is made that deeply buried carbonaceous sedimentaries were undoubtedly the source from which such carbon or bituminous matter was derived. This, I do not consider a reasonable or common sense view of the matter. Carbon is one of the elements of which the earth is composed. In the table giving the periodicity of the elements it comes sixth in the order of increasing atomic weights. It is an element formed like all the rest were formed, and must be as common to the interior of the earth as the rest of the eighty-odd elements so far discovered. The spectroscopic analysis of light from the sun, and the stars, shows the presence of carbon in the sun and in the colder stars. Thus with carbon, an element, found throughout the universe as well as on the earth, it is entirely reasonable to consider it as present in the interior of the earth with the other elements. Such being the case, the magmatic origin for the various forms of carbon in rocks and ores is a rational and logical conclusion. If but a small fraction of thought and effort was made along these lines, which is made in fostering the idea of the organic origin of the carbon found in the earth's crust, untold advances in this phase of geological science would result.

Jan 1, 1925

By K. G. Chipman

IN 1936, the Department of Mines and Resources was formed by the amalgamation of the former Departments of Mines, Interior, Indian Affairs, and Immigration. In the amalgamation, the Geological Survey and the Topographical Survey became the major divisions of the Bureau of Geology and Topography, which is a part of the Mines and Geology Branch which, in turn, is a part of the Department of Mines and Resources. The Topographical Survey was formed by combining the former Topographical Division of the Geological Survey and the air and ground mapping sections of the former Topographical and Air Survey Bureau of the Department of the Interior. The latter organization, previous to 1933, had been known as the Topographical Surveys Branch of the Department of the Interior. The amalgamation of 1936 definitely placed on the Topographical Survey the responsibility for the original mapping required for the development of our natural resources. The war has brought upon us the situation where all work has had to be in the furtherance of the war effort. With decreased staff and limited appropriations, the mapping on those scales which are directly concerned with the natural resources has been confined to the search for oil and strategic minerals. The reconstruction period will produce a different situation, with different problems. The past is behind us and it is necessary to prepare for the future. First, we should consider briefly a few general principles in the making and using of maps, then take stock of what we have, see what the needs are, and consider how we are to meet these needs.

Jan 1, 1944

By Y. S. Sun, Northeastern University, W. B. Li, P. Gao, Z. Y. Zhang, J. W. Yu

"The boron-bearing iron concentrate was extracted from ludwigite ore by the process of magnetic-gravity separation. In order to fully utilize the refractory ore and meet the boron consumption of China, a novel process for separation of boron from iron in boron-bearing iron concentrate was proposed in this paper. In particular, laboratory scale experiments of improving boron reactivity were performed. Fine boron-bearing iron concentrate briquettes were reduced by bituminous coal completely at 1125 °C for 150 min. The effect of sodium carbonate, which was used as an additive in the roasting process, was investigated. The addition of sodium carbonate decreased the boron reactivity and facilitated the volatilization of boron. The influence of diverse cooling methods of the reduced samples on the boron reactivity was studied. The results indicated that boron reactivity could reach up to 80.76% when the reduced samples were cooled by rapid water quenching. In addition, the magnetic material containing 92.71 % Fe with a recovery of 95.11 % and boron-rich non-magnetic material containing 14.51% B2O3 with a recovery 88.85% could be obtained by low-intensity magnetic separation. The magnetic material and boron-rich non-magnetic material were good raw materials for steel-making and borax production, respectively.INTRODUCTION Ludwigite ore is abundant in Liaoning province of China, with 28.43 Mt B2O3 accounting for 57% of the boron resources of the country (Liu et al., 2006). However, it has not yet been utilized on an industrial scale due to its complex mineralogy and fine mineral dissemination (Wang, Wang, Ding, Ma & Xue, 2012). At present, boron-bearing iron concentrate and boron concentrate can be obtained from ludwigite ore using magnetic-gravity separation. The boron concentrate contains B2O3 12%~16%, which can be used as a high-quality raw material for the boron chemical industry after activated roasting, but the B2O3 content in the iron concentrate reaches up to 4%~6%. In order to further separate boron and iron from boron-bearing iron concentrate, a blast furnace and a solid pre-reduction followed by electric arc furnace melting have been proposed (Liu, Cui & Zhang, 1998; Wang et al., 2012). However, both of these two current routes face the same crucial problem that molten boron-rich slag has to be cooled slowly to obtain the alkali-dissolution activity of boron, which affects the yield of boron resource."

Jan 1, 2016