Search Documents

By W. M. Tupper

Municipal governments recognize the importance of aggregates in the local economy and the need to manage this resource in the interest of the public good. They have encountered problems with regulating the industry and the dichotomy between the urban need and the rural source. They have suffered from a lack of financial benefit, an adequate aggregate inventory, provincial strategy, economic information and public understanding. A provincial strategy for ensuring the availability of aggregate supplies to developing areas of the Province is essential. The Province should also be responsible for licensing, research, technical expertise on rehabilitation, public education and financial assistance. Upper-tier municipalities (regions or counties) should assume responsibility for resource management, including resource availability, demand characteristics, truck routing, phasing of resource development and sequential land-use planning. Area municipalities (towns and townships) can best determine the social and environmental impact of a specific aggregate development proposal and should therefore have the primary responsibility for the location of new pits and quarries. They should also have the authority to supplement provincial regulations concerning operating standards and the phasing and standards of site rehabilitation.

Jan 1, 1978

By M. Mirnezami, D. Lascelles, J. A. Finch, E. El-Ammouri

"Aggregation, i.e., the tendency of particles to cluster, can be expected to influence flotation selectivity. In this paper, a method of measuring aggregation is introduced and used to conduct plant surveys.Aggregation is measured using settling rate and turbidity converted to an aggregation index (AI) where 0 corresponds to most dispersed and 1 to most aggregated over the range of conditions tested, normally pH. Surveys of Cu and Zn flotation stages at four concentrators showed the AI increased significantly above pH 9. The metal ions identified in the process waters, principally Ca and Mg, were tested to determine which might be responsible. The presence of Mg was found to be the most important. In doping tests, Mg was shown to cause significant variation in AI over the pH range of 9 to 12.The impact of Mg was restricted to pH > 9. Over this pH range, Mg forms a range of hydroxy species, including Mg(OH)2 precipitates. An aggregation mechanism associated with these precipitates, electrostatic bridging, is suggested. Possible problems and opportunities in flotation practice arising from the findings are discussed."

Jan 1, 2002

By M. Mirnezami, J. A. Finch, M. S. Hashemi A.

The surface of -30µm silica suspension (2% v/v) treated with 100 ppm Mg2+ at pH 11 was fully coated with Mg(OH)2. Under this condition, the silica is strongly positively charged (+30 mV) and the suspension is dispersed. Subsequent addition of Ca2+ promoted aggregation and reduced the surface charge. At this pH calcium is present as Ca2+ and CaOH+, i.e., positively charged ions interacted with the positive surface. Aggregation by a chemical bridging mechanism is proposed. The observation may be relevant to the widespread practice in mineral processing of adding lime to promote aggregation and settling in concentrate thickeners.

Jan 1, 2004

By Nick Hazen

Many successful actions are required to bring a profitable extractive metallurgical operation into production. Competent process development performed within the project development schedule increases the chances of obtaining project financing and decreases the risk of engineering design errors being built into the commercial plant. The general sequence of steps in process development is well known: technology review, desktop studies, scoping studies, prefeasibility, and so on, with an increasing requirement for experimental evidence as the studies advance. This paper suggests principles for guiding process development work so that the efforts stay on track toward a smooth startup and a profitable commercial operation. It emphasizes closely aligning the research with the corporate goals of the mining company management, understanding the mineralogy and variability in the deposit, and guiding by flowsheet and material balance. Examples of hydrometallurgical process development leading to the early use of solvent extraction in the mining industry are given.

Jan 1, 2014

By N. R. Andrade-Gonzalez

The present work was performed on four alloys containing Al-6 2 wt pct Si-3 5 wt pet Cu, with magnesium in the range of 0.02-0 40 wt pct, and strontium in the range of 0-165 p p m Tensile bars were cast in a permanent mold (ASTM B108-160) and heat treated at 495°C for 4 hours, followed by quenching in hot water. Two different artificial aging temperatures were applied at 180 °C and 220 °C for times from 0 5 h up to 8 h Tests were conducted with the intent of determining how the mechanical properties of an aluminum-based 319 alloy are affected when aging time and temperatures are varied In general, it is seen that the alloy does not exhibit the common peak-overaged aging condition due to the presence of several coexisting phases, indicating that they form through complex eutectic reactions late in solidification.

Jan 1, 2004

By S. Onuki, T. Ando, M. Tejima, R. Enomoto, Y. Okada

"Al–Si–Cu–Mg die casting alloys are widely used in the automotive industry, and recent advancements in high pressure die casting technology enable heat treating products to achieve desirable properties. However, CO2emissions associated with die-casting production lines should be reduced to address the global warming issue. In this study, the relation between the microstructures and thermal stability of precipitates formed during isothermal aging at 423, 485, and 558 K of Al-11.0 mass%Si-1.8 mass%Cu-0.2 mass% Mg (JIS ADC12) was investigated using Vickers hardness tests and transmission electron microscopy (TEM). The hardness tests and TEM results showed that Si compounds and Al–Cu compounds enhanced the mechanical properties of the alloy and that the predominant compound affecting the mechanical properties differed between specimens treated at 423 K and those treated at 558 K. Moreover, additional aging at 423–458 K resulted in a material with a Vickers hardness higher than that of the isothermally single-aged material. Differential scanning calorimetry, differential elemental analysis, and selected-area diffraction analysis using TEM suggested that the combination of Al–Cu compounds precipitated at low aging temperatures and Si compounds precipitated during preliminary aging increased the mechanical strength, resulting in a maximum hardness of 130 HV.INTRODUCTIONAl–Si–Cu–Mg die casting alloys have well-balanced mechanical properties, machinability, and cast ability. These alloys are therefore widely used in the automotive industry because of their superior characteristics, accounting for>90% of the aluminum used in die casting production. As a substitute for iron-based materials, these alloys have contributed to the development of lightweight vehicles.Dong et al. (2014) reported that the heat treatment of die casting materials is effective for changing their dimensions under high temperatures as a result of the precipitation of solid-solution elements. Recent advancements in high pressure die casting technology have led to the application of heat treatments of Al–Si–Cu–Mg alloy products to reduce fuel consumption and satisfy customer needs. Although attempts to reduce CO2emissions have focused on fuel consumption in cars and fuel efficiency regulations have become increasingly strict in recent years, CO2discharged from production lines should also be reduced without adversely affecting the properties of the product. Heat treatments for artificial aging after solution treatment (T6 treatment) and after casting (T5 treatment) are CO2discharge sources, which together with a holding furnace account for >80 % of the CO2discharged during the casting process."

Jan 1, 2018

The primary arsenic minerals in the uranium ore processed at the McClean Lake Operation are rammelsbergite, niccolite and gersdorffite. During processing, a large fraction (80 - 95%) of these reduced minerals is oxidized and dissolves primarily as As5+ in the leachate solution. In the tailings preparation circuit the dissolved As5+ is precipitated as a poorly crystalline form of the mineral scorodite. Following subaqueous deposition in the tailings management facility, a temporal rise and fall in arsenic pore water concentrations has been observed. This is due to the oxidation of the residual quantities of reduced arsenic minerals initially present in the tailings sediment. The XANES (x-ray absorption near edge spectrometry) technique has shown that the As1- is gradually oxidized to As3+ and then finally As5+ in the tailings sediment. This oxidation process results in a temporary accumulation of As3+ in solution and is the source of the rise and fall in arsenic concentration observed.

Aug 1, 2010

By Wataru Inagaki, Kozo Kawano, Tetsuya Ando

Cu–Ni–P alloys are the typical precipitation-hardening material. Thus, Cu–Ni–P alloys is expected to apply alternative materials for heat-exchanger tubes. Therefore, it was investigated that the effect of the heat-treatment simulated brazing on mechanical properties of Cu–Ni–P alloy in this study. The hardness of specimen as heat-treatment simulated brazing after solution heat treated (sht) was shown approximately 105 HV. The peak hardness and tensile strength of the specimen as performed aged at 498 K for 43.2 ks following the heat-treatment simulated brazing achieved at approximately 140 HV and 260 MPa, respectively. From these results, it is expected the application to higher-strength tube for heat-exchanger after brazing in a furnace. INTRODUCTION Copper prices have increased dramatically with high in recent years. At the same time, manufacturing industries are required to reduce the environment load by reducing the wall thickness of the copper tubes used in heat exchangers. High-strength copper alloys are developed for reducing the wall thickness, while achieving high strength, of the copper tubes. Moreover, excellent workability and corrosive durability are also required by these copper tubes. Furthermore, the brazing, which are carried out at about 1050 K during the assembly process of heat exchangers, leads to grain growth and re-solving of additive elements. Nomura et al. achieved a tensile strength and Vickers hardness of approximately 260 MPa and 110 HV, respectively, after aging at 723 K for approximately 36 ks. Tamagawa et al. studied that the strength of Cu–Ni–P alloy rapidly increased at about 125 HV during the cooling process after the heat brazing due to the Ni2P precipitates sized 5–10 nm. Furthermore, Inagaki et al. achieved a Vickers hardness of approximately 130 HV by aging at 498 K for 10.8 ks. In the present study, we focused on the lowest aging temperature of 498 K in the previous study, and investigating the effect of heat-treatment simulated brazing on the mechanical properties of the Cu–0.93 mass%Ni–0.24 mass%P alloy.

Jan 1, 2019

By J. Cayouette, C. Bolduc, P. Blatter

"The LaRonde mill was commissioned in 1988 and began treating ore from the Penna shaft in 2000. The mill has been expanded to accommodate 7,500 t/day, but ramped down to 6,000 t/day since the deep extension began. The process recovers gold, silver, and base metals. In 2008, the Goldex plant began trucking gold-pyrite concentrate to a treatment plant feeding pulp to the LaRonde mill, increasing gold output by 40,000 oz. In 2009, the high-grade Lapa ore processing facilities were annexed to the LaRonde plant, increasing gold output by 120,000 oz. This paper outlines the metallurgical considerations related to the treatment of different ore types.RÉSUMÉ Le concentrateur de la mine LaRonde a été mis en service en 1988 et a commencé à traiter le minerai du puits Penna en 2000. La capacité du concentrateur a augmenté afin de permettre le traitement de 7 500 tonnes de minerai par jour, capacité qui est retombée à 6 000 tonnes par jour (tpj) depuis le début de l’extension en profondeur de la mine. Ce procédé permet de récupérer de l’or, de l’argent et des métaux communs. En 2008, l’usine de traitement Goldex a commencé à transporter par camion du concentré de pyrite et d’or vers une usine de traitement alimentant en pulpe le concentrateur de LaRonde, augmentant ainsi la production d’or de 40 000 onces. En 2009, les installations de traitement du minerai à haute teneur de Lapa ont été annexées à l’usine de traitement de LaRonde, augmentant la production d’or de 120 000 onces. Cet article passe en revue les considérations métallurgiques liées au traitement de différents types de minerai."

Jan 1, 2017

By J. Cayouette, C. Bolduc, P. Blatter

"The LaRonde mill was commissioned in 1988 and began treating ore from the Penna shaft in 2000. The mill has been expanded to accommodate 7,500 t/day, but ramped down to 6,000 t/day since the deep extension began. The process recovers gold, silver, and base metals. In 2008, the Goldex plant began trucking gold-pyrite concentrate to a treatment plant feeding pulp to the LaRonde mill, increasing gold output by 40,000 oz. In 2009, the high-grade Lapa ore processing facilities were annexed to the LaRonde plant, increasing gold output by 120,000 oz. This paper outlines the metallurgical considerations related to the treatment of different ore types.RÉSUMÉ Le concentrateur de la mine LaRonde a été mis en service en 1988 et a commencé à traiter le minerai du puits Penna en 2000. La capacité du concentrateur a augmenté afin de permettre le traitement de 7 500 tonnes de minerai par jour, capacité qui est retombée à 6 000 tonnes par jour (tpj) depuis le début de l’extension en profondeur de la mine. Ce procédé permet de récupérer de l’or, de l’argent et des métaux communs. En 2008, l’usine de traitement Goldex a commencé à transporter par camion du concentré de pyrite et d’or vers une usine de traitement alimentant en pulpe le concentrateur de LaRonde, augmentant ainsi la production d’or de 40 000 onces. En 2009, les installations de traitement du minerai à haute teneur de Lapa ont été annexées à l’usine de traitement de LaRonde, augmentant la production d’or de 120 000 onces. Cet article passe en revue les considérations métallurgiques liées au traitement de différents types de minerai.INTRODUCTIONThe LaRonde metallurgical plant in the Abitibi region of Quebec, Canada, evolved into a mature milling site following expansions in 2000–2003, thanks to improved processes, manpower, and water treatment capabilities that better accommodate the complex constituents of the LaRonde ore. The ore requires a sequence of grinding, copper- lead and zinc flotation, and precious metals leaching, ending with a carbon-in-pulp (CIP) gold recovery. A portion (35%) of the tailings is sent back underground as paste backfill after being treated with the SO2-air cyanide destruction process. The tailings area has a dedicated cyanide destruction and metal precipitation area through which the used water passes before returning as recycled water. A biological water treatment plant was built in 2004 to address water toxicity in the final effluent. The water toxicity was the result of the high sulfide content of the LaRonde ore (from thiocyanate or stable cyanide species buildup) and the use of 90% recirculated water in the mill. The water treatment plant uses bacteria to transform thiocyanate into nitrates and precipitate phosphorus from the water before it is discharged into the environment."

Jan 1, 2017

By Jean Robitaille

La découverte du gisement du puits Penna a nécessité une révision complète de tous les circuits du concentrateur Laronde pour permettre, premièrement, l?adaptation du procédé à la nouvelle minéralogie et deuxièmement, l'accroissement du tonnage de 1800* à 4500 t/j. Aux circuits existants de broyage, de flottation du cuivre, de cyanuration et du charbon en pulpe, les circuits suivants furent greffés : broyage semi-autogène, flottation du zinc, manutention des concentrés (épaississage, filtration, entreposage et chargement automatisé), décantation à contrecourant et précipitation au zinc, destruction des cyanures et remblai en pâte. Cet article se veut une revue des différentes étapes du projet d'agrandissement du concentrateur qui se sont effectuées par phases progressives de 1997 à 2000. De plus, une description des nouvelles technologies sélectionnées et implantées est présentée.

May 1, 2001

By J. Cayouette, . Blatter, P. Cousin

The Laronde mill was commissioned in 1988 and has been treating the Laronde Perim ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually. In 2008, the Goldex plant began trucking high wade (35-45 Wt Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold wade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine. Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa)

Jan 1, 2011

By Jean Cayouette, Paul Blatter, Paul Cousin

"The Laronde mill was commissioned in 1988 and has been treating the Laronde Penna ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually.In 2008, the Goldex plant began trucking high grade (35-45 g/t Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold grade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine.Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa).INTRODUCTIONFollowing the 2000 to 2003 expansions, the Laronde plant evolved into a mature milling complex with developed processing, man power, and water treatment capabilities able to accommodate the complex Laronde ore. The ore requires a series of grinding, copper/lead flotation and separation, zinc flotation, zinc tails precious metals leaching, followed by a counter-current decantation circuit and Merrill Crowe precipitation. A paste backfill and SO2-air cyanide destruction operate intermittently. The tailings area has a dedicated cyanide destruction and metals precipitation plant prior to water recycling to the mill. A biological water treatment plant was put into service in 2004 to address the build-up of thiocyanate in the tailings ponds at Laronde. This was the result of the high sulphide content of the Laronde ore and 90% recirculation of the process water. The plant uses bacteria to oxidize and destroy thiocyanate, and removes phosphate from the water before it is released to the environment."

Jan 1, 2011

By John Mair

The Ilimaussaq Intrusive Complex in south Greenland is a layered alkaline igneous body that is predominantly comprised of agpaitic nepheline syenites. The Complex is now recognized as containing vast resources of uranium in polymetallic ores that are also strongly enriched in rare earth elements (REEs) and zinc. Uranium and REEs are dominantly hosted in phosphate minerals with a minor proportion hosted in zirconium silicate minerals. Equivalent ores are yet to be mined for uranium anywhere in the world; however, studies are well advanced in confirming a process route to economically extract uranium. The Ilimaussaq Complex is considered the world?s type-locality for agpaitic rocks. Formation of the complex is attributed to four successive pulses of magma. The first produced an augite syenite, which now forms a marginal shell. This was followed by intrusion of a sheet of peralkaline granite. The third and fourth stages make up the bulk of the intrusion and are peralkaline to hyper-agpaitic in composition. The third batch of magma differentiated to produce pulaskite, foyaite and naujaite. Stage four produced the kakortokites and lujavrites, which are the units of particular economic significance. Kakortokites are strongly enriched in zirconium, niobium and tantalum, whereas the lujavrites are strongly enriched in uranium, rare earth elements, fluorine and zinc. Lujavrites are vertically zoned with arfvedonsite (black) lujavrites grading downward into aegerine (green) lujavrites. The upper most portions of the black lujavrites contain uranium concentrations of greater than 450 ppm, which decreases toward green lujavrites where uranium concentrations rarely exceeds 200 ppm. Resources defined to date in accordance with the Australian JORC code include 282 M lbs of uranium oxide at a grade of 280 ppm. With scope for several other similar sized resources within complex, the overall potential resource is of immense global significance. Metallurgical studies to date indicate that uranium can be successfully extracted from black lujavrites via an alkaline pressure leach method. This involves selectively leaching uranium with solutions containing carbonate and bicarbonate at elevated temperature and pressure. Uranium can then be recovered by hydrogen reduction to create a uranium oxide product. There is also scope to beneficiate ores as uranium and REE?s are hosted in specific mineral groups. Phosphate minerals can be effectively concentrated by froth floatation and uranium-bearing silicate minerals can be concentrated by gravitational methods. Studies indicate that REEs can be extracted from the residue following the alkaline leach process by a dilute hydrochloric acid wash, with REEs then precipitated in the form of a REE concentrate.

Aug 1, 2010

By M. N. Pons, E. Benizri, B. Laubie, A. Bani, Université de Lorraine LRGP, P. Kidd, A. J. M. Baker

"Serpentine (i.e. ultramafic) outcrops in Europe cover more than 10,000 km2 and have a low-fertility and low-productivity, making them unattractive for traditional agriculture. In general, these areas are slowly abandoned by local farmers, affected by strong rural exodus and landscapes undergo a process of closure. However, ultramafic landscapes have the potential to provide multiple ecosystem services that can contribute to Europe’s goals towards insuring food security, production of renewable raw materials and renewable energy. Phytomining (agromining) aims at cultivating metal hyperaccumulator plants that are able to accumulate Ni and other strategic elements from metal-rich soils and transport them to the shoots (>1%), which can then be harvested as a bio-ore. Such metal-rich biomass can be used to recover highly valuable metals, e.g. nickel (Ni) and also to produce energy (heat, electricity). Nickel agromining can thus offer an eco-efficient alternative to classical pyro- or hydrometallurgical processes without disturbing the soil cover and the geology from soils and rocks that would be considered as low grade ores or sterile material for conventional mining methods.Phytomining agroecosystems can lead to better soil resource efficiency and can offer a fully integrated, new agromining agriculture that could cover thousands of km2 in Europe, benefit local communities with a sustainable rural development and provide a wide array of ecosystem services which will need to be optimised under a life cycle assessment methodology:1. Production of bio-sourced metal products2. Production of energy biomass3. Restoration of soil fertility for conventional agriculture (Ni stress)4. Limiting Ni intake by local populations and farmers5. Use and conservation of local biodiversity (plant and soil fauna and microflora) as cultivated ecosystems6. Store carbon in cultivated soils7. Enhance pollination activity at landscape level.Nickel agromining could therefore change the economical balance in historically-disadvantaged ultramaficregions of Europe"

Jan 1, 2016

By M. N. Pons, F. Ferrari, V. Houzelot, B. Laubie, A. Bani, Université de Lorraine-CNRS LRGP

"More than 400 plants in the world are able to accumulate nickel in their aerial parts at concentrations higher than 10 g per kg of dry biomass. Then, nickel (Ni) can be recovered from the biomass of these hyperaccumulator plants. Agromining is a chain consisting in growing such plants and recovering metal and has been developed thanks to the combined know-how of agronomy and hydrometallurgy. Plants can be grown on serpentine soils, containing rather high concentrations of Ni, on sterile heaps or on contaminated soils. This crop enables us to extract Ni from secondary resources, and to improve soil quality by lowering its metal content. For example, Alyssum murale can be grown at the field scale in the Balkans, at yields corresponding to 110 kg Ni per hectare.Hydrometallurgical processes have been designed from the lab scale to the pilot scale to produce nickel salts: ANSH (ammonium and nickel sulphate hexahydrate), nickel sulphate, acetate, etc. and so on. These salts are used for surface treatment and in the paint and chemical industry. Ni salts are prepared from ashes, after plant calcination. Processes are based on the conventional methods of hydrometallurgy: acid leaching followed by different precipitation steps. These processes will be presented, as well as the pilot scale design. A life cycle assessment has been performed and clearly shows the environmental interest of this approach as a potential part of an anti-erosion strategy. An economic assessment has proved process feasibility and the final step is the launching of a start-up. At the moment, the approach is widened to other metals (cadmium, cobalt) and rare earth elements (REEs)."

Jan 1, 2016

Discovery of an economic diamond deposit produces considerable wealth in terms of jobs, royalties, mining investment, and economic spinoffs for residents, including Aboriginal peoples. Diamond mines contribute to the GDP, increased personal income per person and reduced unemployment rates. Is it possible in Alberta?

May 1, 2008

By D. G. Osborne

"The paper describes current 'tools' available to the coal preparation engineer for carrying out the evaluation of data, process design, selection of equipment and layout and design of coal preparation plants.Laboratory and pilot-scale equipment is widely available and test data can be used to provide valuable design information regarding capacities and sizing for specific applications. Pilot plants, unless they fit closely to the basic design envisaged for the eventual commercial plant, C(In often provide only limited useful information.Computing aids such as equipment simulation, plant modelling, etc. are becoming widely applied for establishing design criteria and investigating flowsheet options . Other computer tools such as computer-aided design systems are taking over some of the time-consuming tasks of detailed layout and design and estimation of quantities, etc. and providing the means for detailed examination of more than a single option.Besides computer modelling there is also physical modelling of plant buildings, plant sites and entire proposed mining areas; the former can be especially useful in finalizing design and threading' pipework and electrical reticulation systems through the plant without the resultant risk of impairment of flow, obstruction or wastefulness. Not the least of the benefits of plant models is the assistance provided for training new operating and maintenance staff."

Jan 1, 1985

By H. M. A. Rice

"The Ainsworth mining camp is on the west side of Kootenay lake; British Columbia; 14 miles south of the town of Kaslo. It is in one of the oldest mining districts in central British Columbia; for mining started there in 1888. Its principal production was between 1905 and 1920. Activity since then has been sporadic. According to available records; some 222; 000 tons of ore had been produced from the camp up to 1942.GENERAL GEOLOGY Bedrock in the district consists of a succession of quartzite, quartz-mica schist, hornblende schist, and limestone of Late Precambrian, Carboniferous, and Triassic age. Most of the hornblende schists are of volcanic origin but some formed from related intrusions. The Nelson granodiorite batholith of Jurassic age borders the camp on the west. There is also a series of basic dykes of much later age."

Jan 1, 1954

By Alex MacEachern

Air is the gaseous substance that envelopes the earth and forms its atmosphere. It is remarkable in the constancy of its composition; for while this is being continually changed as the result of the respiration of men and animals, and by addition of gases arising from organic changes and the products of combustion, it is ever being brought back to normal and the proper balance restored by the processes of plant and vegetable life. Nature sees to it that the air in which we live and breathe is kept purified. This does not apply to the air in a coal mine, where there are no natural forces to change and make use of the different gases formed or evolved, and where mechanical ventilation is the only effective means of keeping the air pure. The atmosphere consists of oxygen and nitrogen, not in the combined state but merely mixed. By volume, the composition is: oxygen, 21 percent, nitrogen, 79 percent, there being included with the latter small quantities of such substances as water vapour, carbon dioxide, nitric acid, ammonia, ozone, argon, neon, and organic gases. Of the two principal gases which form air, oxygen alone supports life. When air is inhaled into the lungs the oxygen is absorbed by the blood, which carries it through the body to nourish and energize it. Exhaled air consists of water vapour and about 4 per cent carbon dioxide, with from 16 1/2 to 17 per cent oxygen and 79 per cent nitrogen; the oxygen alone having been drawn on to any considerable extent.

Jan 1, 1930