Search Documents

By G. Belzil, F. Robichaud, M. Fullam

ABSTRACT The Goldex mining and milling complex is operated by Agnico-Eagle and is located in the Abitibi greenstone region of northwestern Quebec, Canada. Commercial production started in 2008. Average gold recovery is 93.5% with approximately 68% of gold recovery coming from the gravity circuit. During the first three years of production, three gravity audits were carried out to optimize performance of the gravity circuit. This paper presents results of the audits and the development of a model linking gravity and overall gold recovery, and outlines improvements made to increase gravity performance and reduce operating costs.

Jan 1, 2013

By Stuart McTavish

"Noranda's Goldstream mine is a 1,500 ton per day copper-zinc mine located 60 miles north of Revelstoke, B.C.The orebody which contains 3.69% Cu and 2.69% Zn was discovered in 1972. Construction of the mine and mill was completed in 1982 and start up was achieved in May 1983.This paper will describe the flowsheet and related equipment 1n the crusher and mill, in particular the dewatering section where two Larox pressure filters are used to dry the concentrates.INTRODUCTIONThe Goldstrean property is located 60 miles north of Revelstoke, B.C. in the Goldstream River Valley (Figure #1). It was discovered during the construction of a logging road in 1972. Exploratory drilling was initiated in 1975, and in 1976 a portal was collared to obtain underground data. Samples were taken from the underground workings for metallurgical bench tests and a pilot plant run.Due to economic conditions, the decision to go into production was delayed until 1980. Concentrator construction and underground development progressed simultaneously during 1981 and 1982, and were completed by the end of 1982. Start up of the concentrator was achieved on May 2, 1983.The ore typically contains about 40% sulphides, which are chalcopyrite 10%, sphaletite 6%, pyrrhotite 20%, and pyrite less than 5%. The sulphide minerals have a high degree of intergrowth. Most of the sphalerite occurs in micron sized grains which are embedded in the pyrrhotite and, to a lesser degree in the chalcopyrite. There is also some fine dissemination of the chalcopyrite in the pyrrhotite. The waste rock is made up of about 30% quartz, 20% guange silicates, and 10% carbonates. The ore has a specific gravity of 3.2 and a natural pH of 8.2."

Jan 1, 1985

By Audrey Wagenaar

Introduction ?? Rising public pressures are being placed on companies worldwide to protect the environment and the health and safety of their workers and local communities. ?? International bodies and shareholders want to make sure developments and companies can meet internationally acceptable standards for EHS. In 2005, Golder Associates was asked by the IFC to conduct a comprehensive review and update for their Environmental Health & Safety Guidelines including the mining sector.

May 1, 2008

By Robert B. Parsons

"On August 8, 1989, the Minister of Finance released a technical paper which sets out many of the details of a proposed 9% federal value-added tax to be called the ""Goods and Services Tax"". The GST, which is scheduled to be implemented with effect from January 1, 1991, will affect all Canadians in different ways and to varying degrees. The mining industry itself should, by and large, benefit from the new tax.IntroductionOn January 1, 1991, it is proposed that the existing federal sales tax will be replaced by a new sales tax - the Goods and Services Tax (GST). GST will be leviedat a rate of 9% on most goods and services consumed in Canada.How it will WorkThe GST will be a tax on the final consumption of goods and services. It differs from a retail sales tax in that it will be collected throughout the production and distribution chain. However, the net effect of the tax paid on a particular good or service will be equivalent. The example above (next column) illustrates the application of the GST to the production and sale of a chair.Illustration of GST for a ChairEssentially, the total tax will equal 9% of the sale price to the final consumer. However, GST will be collected on the value added at each stage of the production and distribution chain . What will be TaxedVirtually all goods and services will be taxed. Items on which GST will not be charged fall into two categories: tax free and tax exempt."

Jan 1, 1989

By Rees J. Llewellyn

Improved product development, assessment methods and evaluation studies of materials for oil sands applications have traditionally focused on low and high stress abrasion and slurry erosion resistance mechanisms, because they were considered to be the predominant wear modes prevailing in oil sands mining, transportation and bitumen recovery. More recently with the very successful introduction of oil sands hydraulic transportation systems, there has been increasing use of crusher systems in which materials of construction are also required to have good toughness and gouging abrasion properties to withstand impact and the severe indentation and ploughing forces that are involved. To assess material property requirements for mitigating this additional wear mechanism, jaw crusher gouging abrasion tests using a modified ASTM G81 procedure, have been carried out on a range of wear materials of interest for oil sands mining service. The method involves a comparison of the wear losses that occur for reference and selected test plates when a controlled amount of standard feed rock is comminuted in a laboratory jaw crusher. Among the classes of material evaluated have been Q&T plate steels, austenitic manganese steel, chromium and chromium molybdenum white irons as plain castings and in laminated forms and also chromium carbide and tungsten carbide overlaid wear plates.

May 1, 2004

By Allan F. Lawrence

"I AM SURE you do not expect from me any learned dissertation on the problems and opportunities of the mining industry. Y our program committee must have recognized my limitations when issuing the invitation to speak to you, because they very thoughtfully left the subject wide open.With the leeway thus granted, I hope that you will bear with me for a few minutes while I try to clarify the impressions of the mining industry that I have gained in the very short time I have held the Mines portfolio and some of the parts that government bas or should have in furthering its development.As I see it, it is the duty of the Mines Department, as an arm of the provincial government, to balance the proprietary rights of all the people against the interests to whom the privilege of developing our resources are, in a s e n s e, leased. To strike a fair balance is not always easy, nor is it possible always to satisfy both sides. Still, under the free enterprise democratie form of government to which I think we al! subscribe, no better way of handling the problem has yet been discovered."

Jan 1, 1968

Keeping the sediment on the mine site and out of the water course is essential from the regulatory, environmental and sustainability perspectives. Regulation of this aspect of mining is embedded in environmental legislation and government receiving water quality standards, and government control has apparently been considered to be the most appropriate method to define mine site discharge standards and the environmental implications of sediment in downstream watercourses. A literature search for guidelines for the site specific design and operation of sediment ponds treating mine site runoff to remove total suspended solids, turbidity and flocculant-induced toxicity, revealed little information on the mining industry?s and government?s roles in defining the ?how to achieve? related to sediment pond design. Is there a need or reason for an industry-driven leadership to clearly define the ?how to? keep the sediment on the mine site and out of the water course? Currently, this issue is addressed in Canada by a federal mining regulation for metal mines which specifies discharge quality for sediment. This paper focuses on the method used in British Columbia, Canada, to regulate and provide a scientific methodology to control the discharge of sediment from mine sites. Management plans relative to this topic are discussed and are considered to have value from the exploration, construction, operation and the onset of closure phases. In addition, the balance and linkage between the erosion control management plan and the sediment pond management plan are discussed in terms of how they may be designed to complement each other to lower the risk of exceeding discharge and receiving water quality standards. If there were an industry-driven standard, or guidance document relative to addressing sediment release, it would benefit mining companies by eliminating the repetitive analysis of this topic for each new mine, mine expansion, and mine modification; also, government may often replace certain aspects of permitting with a regulation, if there is a government/industry established standard defining Best Achievable Technology (e.g. the Canadian Metal Mining Effluent Regulations).

Aug 1, 2013

By E. S. Moore

"The Centre of the silver-producing section of the Gowganda area lies about 55 miles northwest of Cobalt, and the village of Gowganda is 71 miles by road from New Liskeard. The geological similarities of the Gowganda and Cobalt areas led prospectors westward from the rich Cobalt field, first to Elk Lake and then on to Gowganda, where mineralization was found in 1907. A year later many showings were found, and rich hand-picked ore was shipped. Most of the ore has come, however, from two mines, both of which are still operating; the Miller Lake-O'Brien, which was purchased by Siscoe Metals of Ontario Ltd. in 1945, and the Castle-Trethewey. The annual production of these two mines runs over one and one-half million ounces of silver and considerable cobalt. The total production of the camp has reached about 32,000,000 ounces of silver and a large amount of cobalt, the total not recorded.General GeologyThe general geology of Gowganda is in many respects much like that of Cobalt. There are areas of Keewatin basic and acid Javas mixed with tuffs and basic intrusions. These rocks are deformed and partly altered to schists, and have been intruded by some Haileyburian basic and ultra-basic rocks and by Algoman granite. These were followed by a large number of porphyritic Matachewan quartz diabase dykes. After a period of extensive erosion the Huronian sediments were deposited on a pene-planed surface over all the older rocks; these sediments include large quantities of conglomerate (partly tillite), quartzite, and greywacke. The Keweenawan rocks include the Nipissing quartz diabase sill, later quartz diabase dykes, and one long olivine diabase dyke, the latest Precambrian rock. The area has been extensively glaciated.Structural FeaturesThere has been little folding in the area since the Algoman batholiths were intruded, and the Huronian sediments lie nearly flat, with dips of 10, 15, or rarely 25 degrees. The Matachewan dykes show a remarkably uniform, nearly north strike, indicative of east-west tension when they were intruded. On the other hand, the dykes later than the sill strike nearly east, tangentially to the northeasterly and northwesterly strikes of the Miller Lake basin."

Jan 1, 1949

By Angus D. Campbell

Introduction Gowganda forms part of the general Cobalt area. Its rocks and ores are very similar to those of the other parts of the area. While its total production of silver is only 4 per cent of that of the famous Cobalt silver camp, its 1928 shipments contained 42 1/2 per cent as much silver as those of Cobalt for that year. During twenty years of production, 15,000,000 ounces of silver have been shipped from Gowganda. Of this, over 8,000,000 ounces have been shipped in the past five years. The area has thus made for several years a substantial contribution to the wealth of Ontario. Its future depends to a great extent on the priee of silver, which is now, unfortunately, at a record low price. This paper is a discussion of how the Gowganda ore-shoots occur, together with some notes on the milling of the ores at the Castle-Trethewey Mines. The first part is written in the hope of stimulating further study of the silver occurrences, which may lead to further discoveries. The second part, besides being a matter of record, may be of some use to operators of small mills. The drawings in the several Figures illustrating the text are by W. D. Stroud, mine superintendent of the Castle-Trethewey Mines, the benefit of whose opinions I have had in compiling these notes.

Jan 1, 1930

By Mike McKevitt

We are trying to promote a concept and a change in management?s approach to the iterative process of grade control. This is important as grade control must routinely try and achieve the long term objectives set by the mine plan ??BackgroundBackground ??Factors contributing to variation from planFactors plan ??Basis of OptimisationBasis Optimisation ??Ore Block Optimisation processOre process ??Operating mine examplesOperating examples ??Chain of Mining. ??Intention is to highlight the need for repeatable and consistent materialand material-type classification to remain consistent with the Life of Mine Plan ??We can drill another hole or reWe re-optimise a plan, but once excavated, the final decision has been made ??The grade control decision is the last decision made in the resource exploitation sequence.

May 1, 2009

By C J. Coveney

This paper, after a brief introduction to the mineralization and structure in the mine area, outlines the methods now being employed for grade control at Bethlehem Copper Corporation. Sampling, subgrade drilling, blasting and the actual outlining of the ore are among the topics covered. The paper concludes with a summary of the results obtained, showing a reduction in dilution and an improvement in the grade of the copper ore going to the mill. Introduction T HE Bethlehem property is located in southern British Columbia in the Highland Valley about 30 miles southeast of the town of Ashcroft. The property is located within the Guichon batholith. The rock comprising the batholith is a massive, coarse-textured diorite, which, at Bethlehem, has been intruded by a younger quartz diorite, porphyries and breccia, referred to as the "Younger Complex." Mineralization, consisting of chalcopyrite and bornite with minor pyrite and molybdenite, occurs as disseminations, fracture fillings and coarse blebs. The ore zone lies close to the Guichon -Younger Complex contact where, prior to the development of the breccia, the rocks were shattered and jointed. Subsequent mineral

Jan 1, 1965

By R. H. Duthie

As at any other mine in Canada, grade control procedures are used at Steep Rock Iron Mines (1) in order to ensure that concentrator and pellet-plant operator s have a uniform feed so that they can manufacture a pellet to suit buyers' specifications and (2) to maximize ore recovery so that as little as possible finds its way to the waste dump or is downgraded by contamination. At Steep Rock, material grading 40% to 66 % Fe is considered ore. The ore may contain up to 10% sulphur. These ranges create six different stock pile types, with the possibility of more if large concentrations of arsenic are encountered. Although grading and mining techniques used to accomplish these ends are fairly standard, there is an appreciation and willingness by hourly and staff pit personnel to make grade control effective. This produces vertical and horizontal communication, which is necessary for success in this field. At Steep Rock, the waste-to-ore ratio is greater than at any other iron ore mine in Canada. Also, a high percentage of the ore mined is direct pellet feed. For these reasons, .grade control is very important.

Jan 1, 1977

By Eric Toh, Michel David

"Geo-statistics was born from mining problems: grades not being what was expected; more tons of waste than expected; in other words, dilution. Geo-statisticians now claim to have solved many of these problems, but the solutions seem to have a hard time being picked up by practitionners. One of the reasons may be the jargon which geo-statisticians are using. The reason for jargon is that obtaining solutions required a strict formulation in a statistical framework. Practicing mining engineers and geologists are not used to such a framework, and they are not familiar with the jargon. In this paper, the authors re-examine dilution in operating mines and answer two extremely practical problems, using practical language as much as possible. Can dilution be reduced by improving the quality of blast hole samples? How many samples are needed to obtain a good ore-waste discrimination, i.e. to reduce dilution to acceptable levels? Citing real situations, this paper will try to show how fairly simple concepts can be used to answer both problems. It will try to present the solut ions using a minimum of jargon, even if the theoretical solution could be obtained in a few precisely worded paragraphs.The two problems considered are the following: the first one was encountered in the Panguna deposit of Bougainville Copper Limited, P.N .G., but it occurs in every open pit operation where selective mining is required. As the cut-off is lowered, more and more mining occurs in marginal areas. Grade control is mostly based on the grades obtained from blast holes, hence, it is essential that the quality of the blast hole samples be as good as possible in order to reduce dilution, waste being sent to the mill and ore being sent to the waste dump.The second example stemmed from the grade control technique used in many gold open-pit operations in Western Australia: channels are cut on lines 5 m apart and assays are taken every metre. The pattern in the same regardless of rock type, whether one is in the oxidized zone or not. The number of samples to be treated is enormous, hence, the question arises how to find an acceptable sampling grid, and whether changing it can reduce dilution at an acceptable cost.A solution will be given to each problem separately, although in fact it could be seen that the formal framework is the same in both situations."

Jan 1, 1989

By A. W. Jolliffe

DESPITE the widespread occurrence of scheelite in Canada, domestic production of this strategic mineral is still quite insufficient to meet wartime needs. Two difficulties have invariably arisen in prospecting for or developing scheelite deposits: scheelite is a difficult mineral to identify, and secondly, its distribution is commonly so erratic that the value of a deposit cannot be determined without arduous and expensive methods of sampling and wet assay. Scheelite's property of fluorescing under certain ultra-violet lamps overcomes the first difficulty and is the basis for a quantitative method developed to overcome the second. It is found that, by use of an ultra-violet lamp, the value of many scheelite deposits may be accurately and speedily determined. The method requires neither elaborate apparatus nor exceptional skill on the part of the operator, and is most applicable to those deposits where the bulk of the scheelite occurs in fairly pure aggregates that are at least one-tenth of an inch across. It has been used in grading some two hundred scheelite-bearing veins in the Yellow-knife-Beaulieu region, Northwest Territories, and various occurrences in the Porcupine district, Ontario. The method requires the measurement of the total area of scheelite exposed in any reasonably large measured cross-section of a deposit. From the areal percent of scheelite so obtained, the tungstic oxide (WO,) content of that part of the deposit may be calculated by means of equations of simple derivation.

Jan 1, 1942

By K. Horikawa, S. Kitahata, H. Kobayashi

"It has been clarified that the Al-5%Mg alloys containing 200 mass ppm of sodium showed grain boundary (GB) fracture, even when tested at room temperature, as well as at high temperatures (~500°C). SEM/EDX study revealed that the GB fracture was associated with the segregation of sodium on grain boundaries of the Al-Mg base alloys. Differential scanning calorimetry (DSC) revealed that the GB fracture at room temperature of Al-Mg alloys was caused by sodium segregation in the solid state. It was also shown that the tendency of the GB fracture strongly depended on the heat treatment; the alloys after the solution heat treatment showed severe GB fracture compared with the alloys after the homogenizing treatment. Moreover, it was shown that the GB fracture at room temperature by sodium segregation was suppressed by the addition of bismuth or indium. The suppression of the GB fracture by the additional elements was believed to be the scavenging effects by forming the sodium bearing compounds in grains.INTRODUCTIONIt is widely known that Al-Mg base alloys containing high amount of magnesium(~5 mass%)show better workability at room temperature, while that the alloys show grain boundary (GB) embrittlement at higher temperatures ranging from 200 to 500°C, depending on grain size(Otsuka, 1984), sodium impurity level(Ransley, 1959, Okada, 1997, Horikawa, 2001)and testing strain rate(Yamada, 2012). In the case of coarse-grained Al-5%Mg alloys (~300 ?m), 2 mass ppm of sodium causes severe GB fracture around 300°C, however, the Al-5%Mg-2ppm alloy does not show GB fracture at room temperature. It has also been shown that the GB embrittlement caused by 2ppm of sodium was suppressed by the additional elements, such as bismuth (Talbot, 1995), antimony (Ueda, 1997) and indium (Horikawa, 2012). Basedon these facts, we have concluded that the GB embrittlement at higher temperatures of Al-Mg alloys is attributed to the synergy effects of GB segregation of atomic sodium and GB sliding. For the GB embrittlement mechanism of Al-Mg alloys, involvement of low melting point metallic phases has been pointed out (Lynch, 2002),since the GB embrittlement appeared only at high temperatures. Up to date, the effects of high amount of sodium addition more than 2 ppm on GB fracture were not fully investigated in Al-Mg alloys. In the present study, the effect of 100 ppm ordered sodium impurity on GB fracture of Al-5%Mg alloys was examined, together with the effect of another additional elements."

Jan 1, 2017

By E. V. Konopleva, H. J. McQueen, V. M. Khlestov

In addition to increasing grain boundary area during hot working of austenite, the dislocation substructures create potential sites for nucleation of ferrite both at original grain boundaries and at transition boundaries between deformation bands. This development gives rise to a marked increase in the rates of nucleation, of growth and of transformation to ferrite. The combined net effect is product grain refinement that requires less stringent cooling between finish rolling and coiling; hence determination of the above rates would advance process optimization. The important control parameters are the preheat temperature (degree of homogenization), finishing temperature, strain (accumulation near finishing) and the extent of recrystallization after finishing. These effects vary greatly with steel composition; nevertheless, some general rules have been formulated. Moreover, there is also potential for deformation of the refined ferrite. There are other thermo-mechanical processes such as warm forming of metastable alloy austenite to provide a dense substructure that is carried into the martensite on quenching. In other processes, the austenite may be deformed during cooling through the transformation to develop a dense substructure in the ferrite that is stabilized by fine carbides.

Jan 1, 2004

By R. G. Zaripova, N. D. Ryan, H. J. McQueen

The austenitic and ferritic stainless steels do not undergo any phase transformation that induces very fine grains in the product through thermomechanical processing as practiced in most other steels. Considerable grain refinement can be achieved by intense multistage deformation descending through warm to cold working; notably multi-axial forging of bulk material can attain high strains with diminished risk of cracking. Hot working to improve ductility yields finer grain sizes as the T is reduced and strain rate E raised; increased strain has limited effect due to the steady state regime. Ferritic steels develop subgrains with size diminishing as E rises and T falls with the advantage of retained strain hardening; recrystallization delivers grains several times the cell size. In austenitic steels, dynamic recrystallization (DRX) provides finer grains at higher E and lower T with a lower limit due to intergranular cracking. The DRX grains contain a strengthening substructure that can easily be retained by quenching; if static recrystallization is allowed to occur the grain size rises markedly. Multistage rolling with diminishing T is able to provide grain refinement to the same degree as straining at the finishing T yet provides better ductility. grains on recrystallization. As a result of the strain induced transformation to martensite, small subzero deformations of austenitic or duplex steels produce very high dislocation densities that yield marked grain refinement when they revert upon reheating.

Jan 1, 2004

By N. Dahata

Earlier research has indicated that an addition of titanium master alloy to aluminum alloys, results in improved fillability, grain refinement and finer pores. B206 alloy differs from other alloys used in automotive industry, with lower titanium level. This paper examines the effect of alloy chemistry (copper and titanium levels) and grain refinement (A1-5`)oTi- 1%B grain refiner) on grain size, microstructure and microporosity in B206 aluminum alloy. In this study, characterization of grain size, microstructure and microporosity was carried out using light optical microscopy (LOM) and scanning electron microscopy (SEM). Results have shown that the addition of 0.05 wt % titanium resulted in grain refinement of B206 alloy. With an increase in titanium to 0.25 wt further grain refinement, much reduced pore size and uniform distribution of pores resulted. These results suggest that B206 with proper addition of titanium has a promise as an alloy for automotive casting.

Jan 1, 2007

By J. Zollinger, J. R. Kennedy, E. Bouzy, B. Rouat, D. Daloz

"Ni-based superalloys have been replaced in the last low pressure stage of jet turbines for aircraft by titanium aluminides. In order to improve the properties of these Ti-Al alloys and extend their usage deeper into aircraft engines grain refinement by inoculation has been investigated. Borides are the most common inoculants for Ti-Al alloys, however they form brittle particles which are detrimental to the final properties of the alloy. Inoculants manufactured from a Ti-Al alloy with refractory metal additions were proposed to alleviate the issues arising from inoculation with brittle particles. An alloy was chosen which had less than 10% lattice mismatch with the alloy of interest (Ti-46Al) to maximize efficiency. Initial experimentation showed a decrease in as-cast grain size by a factor of 2 between the inoculated and non-inoculated samples along with an absence of the brittle particles found with boron inoculations. Investigations into the interaction between the inoculants and the melt were also carried out to better understand the inoculant size distribution and efficiency upon solidification.INTRODUCTIONTitanium aluminum alloys are an interesting material for aerospace applications. Their high temperature oxidation resistance and high specific strength make them particularly promising (Kim & Dimiduk, 1991). Recently, titanium aluminides have replaced nickel based superalloys in the last low pressure stage of the GEnx turbine engine. In order to increase their usefulness in turbines their properties must be improved for high temperature (>800oC) applications. Grain refinement is one method to improve the properties of a material, however current methods of grain refinement of Ti-Al alloys by inoculation have significant drawbacks. A new method of inoculating Ti-Al alloys by using Ti-Al alloys with small refractory metal additions (Nb, Ta) has been developed to avoid the drawbacks of current methods while still being effective grain refiners."

Jan 1, 2016

By D. G. Eskin

"It is well known that it takes some time for the solid phase to completely dissolve upon melting, especially inside the defects of insoluble particles, e.g. oxides. Until then the oxides remain active solidification substrates in the case of subsequent solidification. It is also known that ultrasonic melt treatment causes grain refinement through activation and dispersion of solidification substrates (one of the mechanisms) and also accelerates the dissolution of solid metal in the melt. In this study we combine these effects and demonstrate that the introduction of an alloy rod into the matrix melt of the same composition results in significant grain refinement, this effect being increased by the ultrasonic vibration of the rod. The achieved grain size is comparable to that obtained by a standard Al–Ti–B grain refiner. All samples were cast using a standard TP-1 mould to enable correct comparison. The effect of the temperature range of the rod introduction, as well as the effect of ultrasonic vibrations are discussed.INTRODUCTION The fact that by introducing solid metal into the melt one can achieve structure refinement is rather well known. As early as in the 1930s–1950s a series of papers and patents have been published, showing the benefits for grain refinement when dissolving solid metal in the melt before solidification (Danilov and Neimark, 1938; Scheil, 1956). Later on this way of structure refinement was developed further and dubbed “suspension casting” or introduction of “internal chills” (Madyanov, 1969; Zatulovsky, 1981). The solid metal was added in a form of cut wire, cut sheet, or powder, with the resulting grain refining, elimination of columnar grain structure in ingots and castings of steel, copper and aluminium alloys. The underlying mechanisms have been suggested as (1) rapid cooling of the melt due to the latent heat consumption upon melting of the solid metal with the resultant melt undercooling and (2) introduction of many solidification substrates in the form of crystal fragments and active non-metallic inclusions (Danilov & Neimark, 1938; Balandin, 1973). A number of patents have been filed where either the same solid alloy or a master alloy with additions (e.g. Ti for Al alloy) is introduced in the amounts up to 50% (typically less than 10%) into the melt close to the liquidus temperature (Schmidt, 1966; Talbot & Soller, 1973, Krupp, 1974; Bondarev, 1979). The main reason that this technique is not widely used in industry is the possible incomplete dissolution of the solid parts introduced into the melt with ensuing inhomogeneous as-cast structure and potential defects. Also the selection of the temperature range where the technology works the best is not clear."

Jan 1, 2018