Search Documents

Existing fluid flow techniques may be readily applied to the design of ranges for seam gas drainage. The Reynolds number characterises the flow regime within the pipe and it can be used in conjunction with data on absolute pipe surface roughness to determine the system friction factor. The application of the solution to the isothermal compressible flow equation utili- sing Moody friction factors and the concept of equivalent length of pipe for fittings and valves provides a practical method for sizing gas ranges. The physical capacity of a range can be decreased by the existence of significant quantities of water in the range and also by the ingress of air into the system at poor pipe joints etc. Both problems can be elimin- ated by adequate attention to design detail.

Jan 1, 1982

R F Johnston 1 ABSTRACT The possibilities for bacterial leaching of refractory gold ores found in the Central Victorian region of Australia are examined. The behaviour of bacteria, especially 77iobacillus ferroaridans is outlined and the effects of these when they are exposed to pyrite, arsenopyrite and stibnite are examined. The factors which are particular to Central Victoria are outlined and the possibility of adapting a bacterial culture to suit the conditions is discussed. It is concluded that a bacterial leaching system is a feasible proposition and that it could enhance leaching rates and yields.

Jan 1, 1994

By B Chappell

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to be placed in a tailings dam. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electroosmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

During the middle of this century, exploration and mining reached a low ebb in New Zealand. Tas McKee did his utmost to rejuvenate the mining industry, using the latest technology and an understanding of the environment far ahead of his time. Today, advances in the geosciences enable sophisticated exploration to proceed to the drilling stage before any significant environmental disturbance is created. Thereafter developments are now carried out with integrated management of the environment and rehabilitation so that disturbed land can be used for other purposes once mining is finished. Thus, we now have environmental engineers and scientists taking their place as professionals in our Institute.

Jan 1, 1987

Detailed observations were made for two existing continuous miner and shuttlecar systems. A simple model for the shift average cycle consisted of three time components - delays, mining and transport. Cycle improvement and productivity improvement factors are derived and used to predict the theoretical improvement which the observed cycles could achieve. Various strategies of action ranging from short-term optimisation through to long-term planning for continuous haulage systems are evaluated. High potential for improvement is shown for a wide range of operating conditions. An overview is presented for systems, currently available or under active development, which can accept coal directly from continuous miners and offer continuous haulage to the surface. Systems are broadly classified as mechanical-roof mounted, mechanical-floor mounted and hydraulic transportation.

Jan 1, 1982

By R J. Norris, D J. MacKenzie

Gold-bearing veins have formed at a wide range of depths throughout the uplift history of the Otago Schist. The earliest gold mineralisation occurred during the later stages of Mesozoic metamorphism. This mineralisation was characterised by diffuse wall rock alteration with greenschist facies metamorphic or retrograde metamorphic mineral assemblages, and gold occurs in this altered rock. Quartz veins formed in .steeply dipping extensional fractures associated with this mineralisation type strike north to northeast. The Macraes mine exploits this deposit type. The present northwest strike of the mineralised zone at Macraes is a result of post-mineralisation deformation of the schistosity-parallel mineralised shear zone which hosts northeast striking extensional veins. This combination of schistosity-parallel shear zone and steeply dipping northeast striking veins may exist elsewhere in Otago, and this deposit type is most prospective. Steeply dipping quartz veins formed during post-metamorphic un-roofing of the Otago Schist strike northwest to west and occur as clusters of near-parallel structures in east and central Otago. These veins consist mainly of massive quartz, although some prismatic quartz occurs also. Breccia fragments in veins are common and these are generally silicified, with some gold. Wall rock alteration is negligible, and vein margins are sharp. A set of middle Tertiary veins occurs in northwest Otago. Most of these also strike northwest and dip steeply, but some strike northeast. These veins contain abundant ankeritic carbonate as well as quartz. The carbonate pervades adjacent wall rock as veinlets, but gold mineralisation is confined to veins. Quartz is commonly prismatic and vuggy, and contains gold, which is commonly coarse grained especially in silicified breccia zones. Associated veins contain stibnite. This vein type formed close to the paleosurface (>2 km). Mineralised veins in Marlborough currently strike northwest, but these have been rotated from northeast strike during Alpine Fault displacement of Marlborough from Otago. Some of these veins were formed under late metamorphic conditions and are similar to the north to northeast striking veins in Otago. As in Otago, this type should be considered to be most prospective if they have associated schistosity-parallel shears.

Jan 1, 2000

Western Mining Corporation, managing partner of the Windarra Nickel Project are in- stalling a raise-bored haulage shaft and under- ground crushing system at the Mt. Windarra Nickel Mine. The system will be the second of its type installed by W.M.C., the first being in- stalled at the Otter-Juan mine in Kambalda in 1976/77. Both haulage systems became necessary as a result of the increasing production limi- tations, and escalating costs of a deep decline mine. The Windarra haulage system required a single 3m diameter vertical raise drill hole to a depth of 470 metres. Two five tonne skips in balance will hoist crushed ore and mullock to the surface, at a design rate of 200 tonnes per hour, effectively reducing truck haulage leads by up to 50%. It is expected the project will be in full operation by mid 1982 and will enable the mine to achieve an annual production rate of 600,000 t.p.a. by 1983.

Jan 1, 1982

Benchmarking of mining operations has been in vogue for a number of years: it seems teams are forever flying around the world to try to understand what other operations are doing. However, unless a benchmarking exercise involves data gathering at a fundamental level and a rigorous analysis process is applied, the trip will be nothing more than industrial tourism. When benchmarking is performed thoroughly, the range of comparisons that can be made is extensive and informative, and need not be restricted to sites with similar conditions and equipment fleets. This paper describes the detailed and rigorous process for benchmarking used throughout AMC benchmarking studies. The paper demonstrates how, through drilling down to the underlying drivers, the often heard cry of æyou canÆt compare us, weÆre differentÆ can be overcome. Included in the discussion are a number of significant issues that have been identified during AMC benchmarking studies. The paper then considers the types of opportunities that have been identified and the potential for improvement. The paper concludes with a discussion of the implications for planning, measuring and management of operational performance.

Jan 1, 2003

By D Pastars, J L. Mauk

Located at the southern end of the Awhitu Peninsula, the Waikato North Head ironsand mine is approximately 50 km southwest of Auckland . The ironsand deposit consists of Quaternary sands, clays and peats, formed by aeolian and marine processes. We sampled on widely- and closely-spaced intervals to test variability within the mining area. X-Ray powder diffraction shows that samples contain feldspars, quartz, pyroxenes, amphiboles, clays and titanomagnetite. Densities range from 1.6 to 2.5 grams/cubic centimetre, with porosities from 30 to 43 percent. The percentage of magnetic minerals values range from 0 to 75 percent, slimes (clay minerals) values of 0 to 26 percent and non-magnetic minerals from 20 to 95 percent. Mineralogical differences in the Mitiwai Formation and Waiuku Blacksand Member cause bimodal populations in the density, magnetic minerals, nonmagnetic minerals and slimes plots. The Mitiwai Formation has higher non-magnetic mineral values and lower density, slimes and magnetic mineral values than the Waiuku Blacksand Member.

Jan 1, 2001

By Armstrong RW, Middlin B

The development, design, construction and operation of the new Solvent Extraction/BCA process plant at Copper Refineries Pty. Ltd., Townsville is described.The process offers substantial savings in electrical power costs, improvements in plant hygiene, and a lowering of materials handling costs compared with conventional electrowinning technology.The solvent extraction process extracts arsenic from copper Tank House electrolyte using a tributyl phosphate (TBP) - kerosene solvent. The plant incorporates fourextraction stages, two scrub stages, and three stripping stages to produce an arsenic-bearing low-acid strip liquor. This strip liquor is mixed with copper sulphate, and neutralized with ammonia to form a copper (II) arsenic (V) crystalline product, bicupric arsenate (BCA). This product is then used in the manufacture of chromated copper arsenate timber preservatives (Royston 1982).

Jan 1, 1985

This paper outlines some of the recent developments in Spiral Concentrator design, with particular reference to the range of Reichert spirals supplied by Mineral Deposits Limited, typical applications, and test or operating data, are also provided for the different series of spirals now available.

Jan 1, 1978

By J Bryant

In recent years the mining industry has suffered from skill shortages in a range of disciplines including mine geology. As a consequence, many businesses operate with incompletely filled organisation charts and technical professionals are frequently thrust into roles earlier than previous generations of geologists, engineers and metallurgists. Exacerbating the difficulties managers face with recruiting suitably experienced professionals is the churn of people through roles. Churn may be caused by internal pressures related to the rapid increase in projects and opportunities within a company or by external factors including the high workforce mobility resulting from the advent of fly-in, fly-out (FIFO). Historically, new entrants into the mine geology profession often received on-the-job training from their more experienced colleagues. This training, supplemented with targeted skills and knowledge enhancement through dedicated short courses, ensured the wide range of skills, knowledge and abilities required in the complex role of mine geology were continually renewed. Faced with an influx of new graduates and a dearth of mine geology professionals in the critical ten to 15 year experience range, the industry needs to develop new paradigms to ensure that the full business benefit of the mine geology function is delivered. This is increasingly important as the complexity of business planning built on geologically-based variables grows. Mine geologists are now faced with the potential incorporation of geometallurgy and waste characterisation along with energy efficiency, carbon-economy and other environmental issues into their roles. Providing baseline data, models, operational control and reconciliation for a wider range of variables further stretches the already limited geological resources available to the industry and exposes personnel with relatively low levels of experience to potentially business transforming decision processes. This paper outlines a successful approach to mentoring at the individual and team level. It discusses what went well and what could have been done differently from both the mentor and menteeÆs perspective with examples from case studies and offers insights into a new approach to dealing with gaps in organisation charts and high turnover of personnel.

Jan 1, 2009

This paper summarises the influence of slurry rheology on the grinding throughput of batch laboratory and continuous plant-scale mills operating in open and closed circuit configurations. The results of controlled changes in percent solids, particle size, slurry temperature, and viscosity control chemicals are demonstrated. An underlying rheological explanation of the above factors is offered which involves tying the specific rates of breakage that are occurring in the mill with the specific rheological character that the slurry is exhibiting at any given set of operating conditions. Some industrial scale operating guidelines are presented which have proven useful in increasing the net pro- duction capability of grinding circuits.

Jan 1, 1978

By E Taylor, F Lebbing

The $2.5 billion EastLink project is a 39 km tollway and includes twin three-lane, 1.5 km long, undrained driven tunnels with cross passages every 120 m. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and help preserve the unique flora and fauna in the area. The design of the permanent concrete lining and waterproofing system for the EastLink tunnels was both innovative and practical, to meet the demanding environmental and production constraints of AustraliaÆs largest road project. This paper describes several key aspects of the tunnel design and construction, including: design of fully tanked, permanent concrete tunnel linings for the main tunnels and cross passages to withstand 37 m head of water pressure in combination with potential rock loading in the future;optimisation of the tunnel shape to minimise the amount of reinforcement required and the design of special welded mesh which was developed within manufacturing constraints;100 year design life and durability considerations in every aspect and detail of the design including concrete mix design and stray current mitigation;development of a precast invert solution for the main tunnel permanent concrete lining to enable faster lining construction and to minimise risks to the tunnel membrane associated with fixing reinforcement and construction traffic;development of prefabricated reinforcement details for the junctions between the main tunnels and the cross passages to enable faster construction and minimise risks to the membrane associated with fixing reinforcement; andincorporating the tunnel drainage sump at the lowest cross passage in the alignment, resulting in deep excavation to satisfy the required storage volumes for drainage.

Jan 1, 2008

By D Smith, D Reid, D Bradshaw, C Brough

The Merensky Reef at Northam Platinum Mine in South Africa is characterised by a high degree of variability with respect to reef elevation (difficult to mine), as well as mineralogy and texture (difficult to process). Development along strike and down dip of multiple reef types has led to unpredictable run-of-mine characteristics that pose problems for the mineral processing circuit at Northam. Following mining terminology, Normal, Transitional (NP2) and Pothole (P2) Merensky reef types can be defined, and this geometallurgical study aims to characterise and understand the relationship between their mineralogical characteristics and laboratory scale batch flotation performance. The plagioclase-rich NP2 reef ore is the easiest ore to process in terms of capacity for high mill throughput as well as flotation performance. The lack of very fine-grained disseminated sulfide textures in the NP2 reef ore results in better liberation characteristics relative to the Normal and P2 reef types. Consequently, chalcopyrite, pentlandite and sulfide recoveries are highest for the NP2 reef ore. The lack of ferromagnesian minerals in the NP2 reef ore also results in the recovery of the least amount of floatable gangue during flotation tests. The Normal and P2 reef ores are similar to each other, with an orthopyroxene-rich mineralogy with associated alteration minerals. The P2 reef is also characterised by the highest sulfide content and degree of pentlandite liberation. Chalcopyrite, pentlandite and pyrrhotite liberation is only significantly increased by a change in grind for the Normal reef ore. The change in grind, however, only significantly affects pentlandite flotation performance and overall froth stability for the Normal reef ore. However, for all three ores, a small change in grind has a detrimental effect on pentlandite flotation performance.

Jan 1, 2008

By Shoobridge PH

Operating difficulties during 1977 with the Imperial Smelting Furnace operated by Sulphide Corporation Pty. Limited at their Cockle Creek zinc-lead smelter were found to be caused by premature softening of sinter in the upper shaft of the furnace. This soft- ening was shown to be a consequence of raw materials and operating policies which led to unusually high levels of both lead and silica in a sinter of low basicity. A programme of softening tests and micro-examination of a range of sinters established that premature softening occurred when lead and silica increased to the point where a lead-calcium silicate with a low lime content became the major continuous phase in the sinter. This information was used to define a range of compositions which kept the softening temperature acceptably high for furnace operations.

Jan 1, 1978

The Australian Constitution specifies certain powers of the Commonwealth Government to be used in its capacity as the national government. Certain of these broad powers result in the Com- monwealth having a facility to play an important part in the development of the mining industry. The State Governments, however, by virtue of their wide powers to regulate matters within the boundaries of a particular State, are more directly involved in the day to day administration and standards of activities of mining operations. In this respect the Common- wealth has something of a dual role because of its "State-like" responsibilities for the mainland Terri- tories. The components of the role that the Common- wealth Government discharges in relation to the mining industry are qualified to varying extents at particular times by the political persuasion of the Government. In absolute terms the components are as follows. 1. Economic management. The Commonwealth's fiscal and monetary policies have an important effect on industry as well as on State finances. In particular, the taxation regime employed by the Commonwealth Government is of direct importance to economic decision-makers in the mining industry. 2. International matters. International trade and commodity matters are, more and more, becoming an everyday part of the conduct of a nation's foreign affairs. 3. Exports. The Commonwealth Government, via the constitutional powers over overseas trade, have exercised varying degrees of control over mineral exports to achieve particular objectives. 4. Foreign capital and investment. Australia in general, and the mining industry in particular, is and will continue to be a net importer of capital. There appears to be bipartisan political agreement in Australia that foreign investment policy must be enunciated to ensure that investors. are in no doubt that Australia welcomes beneficial investment and technology from overseas. 5. Environment and Aborigines. Governments, both Commonwealth and State, have in recent years become more involved in these areas in response to their interpretations of community aspirations. 6. Energy. Access to assured supplies of energy is now viewed, by Governments worldwide, as a desirable asset to ensure the well-being of a nation's people and industries.

Jan 1, 1978

By Player R. L

Measurements of the rate of PbO reduction from high lead metallurgical slags were made under laboratory conditions using graphite, a CO-50%CO2 gas mixture and metallic iron as reductants. The results show a transition in rate-controlling step at low PbO contents (i.e. 6 wt.% PbO). At medium to high PbO contents in the slag, the reduction rate was found to be strongly affected by the slag chemistry, temperature and reductant type. The effect of stirring and hence mass transfer in the slag phase on the reduction rate of PbO was found to be insignificant at medium-high PbO contents. Attention is drawn to the importance of chemically controlled reaction rates at the slag-gas interface. Parallels between these results and test work on a 5 tph scale have been briefly drawn.

Jan 1, 1989

By Olden WH

A scheme is presented whereby the complexities of design and operation of a hydraulically powered coalmine support are modelled using the finite element method. This enables predictions to be made of the interaction of the support with its environment in a variety of operating conditions. The model is a two dimensional representation. The modelling scheme was applied in two case studies. In the first, the performance of a four leg support was uprated by increasing the front leg force. The finite element model enabled changes in overall support performance to be verified. In the second case study, the change in lateral force developed by a two leg support was assessed with changes in support operating height and floor foundation stiffness. The modelling scheme is capable of further development with the possibility of extending the model into three dimensions and the addition of control elements that would enable an actual mining sequence to be Represented.

Jan 1, 1992

By Koppe JC, Strieder AJ

The Rivera Crystalline Island (RCI) is an erosional window of the intracontinental Parana Basin that outcrops in the Rivera Department, north of Uruguay. RCI is made up mainly by Precambrian granites, metasediments and granite-gneisses. This island is crosscut by a dextral transcurrent shear zone system, the Rivera Shear System (RSS). The bulk strain ellipsoid was defined by previous work and has allowed the evaluation of shear dynamics. The geometry of the shear system is made up of two shear directions: E-W (P-shear), which turn right to NW-SE direction (R-shear), leading to the development of extensional bends. The shear zone system was developed in brittle-ductile to brittle regimes, under temperature conditions compatible with greenschist facies metamorphism. The shear zones are marked by an intensive fracture cleavage development. Mylonites develop only in narrow, discontinuous higher strain zones. Internally, the shear zones are dominated by intrusive rocks, mainly granites, dacites and diorites. Hydrothermal alteration has been developed in several areas.The economic significance of RCI is given by several small gold deposits, which have been exploited since 1869. One major new gold mine is under development, the San Gregorio Gold Mine. This gold deposit is locally controlled by a dilatant site where R-shear turns right to P-shear. Mine lithologies were deeply altered by hydrothermal fluids in the dilatant structure. This work presents the lineament-structural analysis carried out to identify similar structural patterns in all RCI sites favourable to host other gold deposits. The exploration program also considered remote sensing, geology, geophysical and geochemical survey.

Jan 1, 1997