Search Documents

By R Rankine

Backfilling with paste fill has been an integral component of open stoping at Cannington since commencement of operations. Efficient paste filling is critical to successful mining of the Cannington orebody. There has been a deliberate and ongoing effort into research and development of paste, with the focus being to optimise the performance and cost of paste. This paper describes the latest research and operational issues of Cannington paste fill.

Jan 1, 2005

By K Matsui, T Sasaoka, S Kubota, Y Yosh

A large amount of wastes from the preparation plant is produced. The properties of these wastes vary depending on the mineralogical contents of the mother rock in which the coal is embedded. The waste quality depends on the method of mining and cleaning. The waste mainly consists of clays, quartz, carbonaceous materials, mica, pyrites and so on. About 55 per cent of coal-ash is now utilised and the remains are disposed of at the disposal sites, however, the life of the disposal site is limited. Moreover, it is difficult to find new disposal sites. Therefore, it is requested that the percentage of the utilisation of the coal-ash be increased in every field in Japan. So, it is very much available if the injection material for natural/artificial openings can be applied on the cement that is added to flyash. Among the man-made pozzolans, a flyash is probably the most successful component used in grout injection. When flyash is added to Portland cement concrete, the same kinds of oxides as those of the cement are being added. As an injection component, flyash acts, in part, as a fine aggregate and, in part, as a binding component. However, there is not a substantial alteration of the properties of the original component. From these points of view, in order to clarify to what degree the flyash content affects the properties of the injected grout mixture; different combinations of flyash, Portland cement and water were considered by means of several experiments.

Jan 1, 2003

Studies of human relations are being made by a team of psychologists within management and in the community of Kambalda as a whole. Some of the first results are discussed with reference to extensions required in management when it also has to run a mining town. Implications are noted for town planning policies of the attitudes and preferences of the population with regard to housing and to other major planning areas. Some of the theoretical and practical difficulties of 'planning the human ecology' are outlined.

Jan 1, 1973

By Grey D, Turner R, Capsanis J

Coal fines are recognised to have a major impact on the cost and efficiency of the recovery of saleable coal. Fines affect the productivity of the whole mining cycle because of the low yields obtained in washing this material as well as affecting the moisture content and handling characteristics of the final product.In 1990, Coal and Allied Hunter Valley Mine initiated an internal study into coal fines based on the assumption that a reduction in fine coal in ROM material will lead to increase yields in the preparation plant. The initial results of this study indicated that the level of fines in the ROM coal can be reduced by more than 40 per cent by simple changes in blast design and implementation.

Jan 1, 1992

By G Anderson, V Lawson, P Voigt

Glencore operates zinc concentrators at both Mount Isa and McArthur River. Both orebodies have a history of complexity and required the development of new technologies to maximise the value from these long-life assets. The Mount Isa orebodies were plagued since operations started in 1931 with complex mineral textures making separation challenging and many areas uneconomic. Examples are given in Figure 1 with different grain sizes from the same orebody in different areas. The McArthur River deposit, located in the Northern Territory, was discovered by Mount Isa Mines geologists in 1955 (Logan, Murray and Williams 1990). The extremely fine-grained nature of the ore was quickly recognised and the difficult separation of the minerals was soon obvious. The geographical, metallurgical and economic factors resulted in the orebody not being developed until the technologies for the mineral separation had been developed. The development of the IsaMill allowed for an economic mineral separation flowsheet to be developed and ore treatment commenced in May 1995 (Nihill, Stewart and Bowen 1998). CITATION: Lawson, V, Anderson, G and Voigt, P, 2018. Developing technologies for a complex orebody, in Proceedings Complex Orebodies Conference 2018, pp 116–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Jancar T, de Guzman M M, Matthews B, Tu J. Y

The use of computational simulation to predict the performance of existing equipment or for the design of improved mineral processing equipment will be referred to as Computational Mineral Processing (CMP) in this paper. The emphasis will be on solving the governing equations for liquid solid flows in complex geometric domains to obtain, typically, the three-dimensional distributions of velocity and pressure for the liquid phase and the velocity and concentration for the solid phase. The underlying technology, computational fluid dynamics (CFD), is very well-developed in other industries (aircraft, car and chemical) and forms a vital part of product design and analysis. The subsequent design of improved mineral processing equipment may also involve finite element structural analysis (FESA). Computational fluid dynamics (CFD) and finite element structural analysis (FESA) are part of the generic discipline of Computational Engineering and Science (CES). Ciment and Scherlis (1993) define CES as `The systematic application of computing systems and computational solution techniques to mathematical models formulated to describe and simulate phenomena of scientific and engineering interest'. Increasing computer power (Kaufmann and Smarr, 1993), is a dominant factor determining the rapid growth of industrial utilisation of CES. This increase is happening at both the supercomputer and the workstation level. Indeed, today's typical workstation, a Hewlett-Packard 735, is as powerful as a CDC 7600, the leading supercomputer in 1970. Future computer architectures are expected to become increasingly parallel (Gartner Group, 1990) allowing a sustained performance of a teraflop (a million megaflops) to be achieved well before the Sydney Olympics in the year 2000. It is recognised that the modem development of most disciplines in the physical sciences rests on the three complementary strategies of experimentation, analysis and computational simulation. As the 21st century is approached the volume of computational simulation, both fundamental and applied, is growing dramatically and the role of experimentation is diminishing. In the area of equipment design, CES provides the following advantages over experimental testing and measurement: 1. lead time in design and development is significantly reduced; 2. CES can simulate conditions not reproducible in experimental tests; 3. CES provides detailed and comprehensive information; and 4. CES is more cost-effective and time-efficient. The ultimate benefit for industry is greater productivity and hence greater profitability. The broader issues in relation to CFD are discussed by Fletcher (1993b). In the five- to ten-year time frame, growth in computer power will make it practical to combine CFD and FESA with optimisation procedures to produce a design process that is almost fully computerised. It is expected that fully automatic

Jan 1, 1995

Access to the Rosebery Orebody, which dips into the western slopes of Mount Black at 45¦, has been achieved in sequence by the following means: - A series of adits down to 8 level - An inclined shaft (No. 1 Shaft) sunk internally from 8 level to 14 level - A vertical circular concrete lined shaft (No. 2 Shaft) sunk internally from 4 level to 19 level. Although the orebody has been fairly well defined to 19 level, deeper ore occurrences have been outlined by a series of drill holes decreasing in frequency with depth to 26 level. No. 2 Shaft (sink) was stopped some 10 m below 19 level in order to make an early start on doubled production at West Coast Mines, with the intention of subsequently extending the shaft or of driving a decline from the lowest operating horizon for deeper access. The decline approach was adopted some six years after production commenced from No. 2 Shaft. The reasons for that decision are outlined, together with an account of the constraints and design requirements imposed by commencing by a vertical shaft in the hanging wall of the orebody.

Jan 1, 1982

By G R. Ballantyne, M S. Powell, M Tiang

This paper reviews the proportion of energy attributable to comminution within the Australian gold and copper mining sector. The need for this is motivated by inconsistencies in the quoted energy usage data and the lack of a common basis for reporting the fraction of energy in mining that is attributable to comminution. This study should form a reliable basis from which to assess both demand and opportunities to reduce energy consumption.The proportion of milling energy was calculated for the major producers in the Australian gold and copper sector. A sampling methodology created by Powell et al (2003 - 2010) was initially used to provide an accurate and meaningful measure of the energy used in the comminution process. However, no useful method for grouping similar mines was found. Fortunately, a surprisingly large amount of high quality data was found from a number of different sources, allowing the development of robust relationships to be used to estimate a high proportion of the unknown values. The fraction of energy attributable to comminution was found to be dependent on how the total energy consumption was defined. For instance, comminution accounted for 52 per cent of the electrical energy, but only 21 per cent of the total energy publicly reported by the mines because a substantial proportion of energy used on a mine is in the form of transportation fuel (mostly diesel). Critically, the measured electrical energy consumption does not account for transmission and generation losses, while diesel energy usage is typically quoted according to its calorific value. This review proposes that diesel should instead be converted via the mechanical efficiency factor for diesel engines. Using this conversion, comminution was found to account for 36 per cent of the available energy on average. This approach allows a useful basis of comparison for mines regardless of whether milling energy is obtained from electrical or diesel generation. A summary of the results are shown in Figure 7 with other values obtained from literature. The total comminution energy assessed in this study accounts for 1.3 per cent of AustraliaÆs electricity consumption, this figure will increase as the other mineral commodities are added to the study.CITATION:Ballantyne, G R, Powell, M S and Tiang, M, 2012. Proportion of energy attributable to comminution, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 25-30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

This paper describes the technique developed by the Australian Coal Industry Research Laboratories (ACIRL) for the treatment of bore core samples to obtain data for coal preparation studies of the target reserves. The particle size distribution within the sample has a significant influence on the relationship between the yield and ash per cent of the floats coal at any ash level. The size analysis within the reconstituted feed from a coal preparation plant is determined by the size analysis of the feed coal, physical degradation of material in the process, and the breakdown of associated shales in water. The extent of material breakdown was studied in the ACIRL coal preparation pilot plants. The method of bore core evaluation includes simulation of this breakdown in a sample selectively crushed to conform with predicted or known run-of-mine size distribution. Modifications have also been made to the laboratory methods for froth flotation to approximate more closely with industrial practice.

Jan 1, 1977

By L M. Zhang, T H. Xu, J Zhao

Blasting is one of the most commonly used strategies for excavation in civil and mining engineering. Yet blasting can also bring along such undesirable effects as ground vibrations and soil disturbance. Numerical analysis is a powerful tool for estimating the effects of blasting and improving blasting design. In this research, a constitutive model for sand is proposed for the numerical analysis of blast-induced ground motions and wave propagation in soil mass. In the model, three model surfaces, ie the critical surface, the dilatancy surface and the bounding surface, are defined following the bounding surface hypoplasticity framework. The strain rate is included explicitly into the model formulations so that the proposed model is valid under high strain rate loadings caused by blast-induced vibrations. The performance of the proposed model is validated by the simulation of drained triaxial compression tests conducted on a crushed coral sand under different strain rates.CITATION:Xu, T H, Zhang, L M and Zhao, J, 2014. A bounding surface model for sand subjected to blast-induced vibrations, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

Underground measurements, observations and computed simulations, started a long time ago were concerning the study of : - occurence of typical rockburst, - inducing, stretching of main fractures in the roof of caved longwalls. They made obvious a foundamental phenomenon of inducing of strata fractures involving contact be- tween two layers quite different in their elastic characteristics : coalseam and rocklayer.. The start of primary cracks in maximum abutment zone takes place in the rock near the contact surface. It is opening of crevasses induced by traction stress component resulting of difference of rigidity of both materials and no sliding on in- terface. Occurence and stretching of these crevas- ses are a rheological phenomenon so that the rate of advance and stops of the face influence the distance between the crevasses and the stretching of these ones. The characteristics of these cracks in space and time affect mining conditions. So it is for fractures proximity and expan- sion inducing eventual blocks formation in longwall roofs in front of faces, for depth and delay of road- ways ribsides fracturing, inducing some rockbursts. In longwalls roofs, cracks initiated in front of a face can be either quite close or quite distant each from the other one, according to the depth of crushed coal in front of the face, which af- fects also extension of the cracks.

Jan 1, 1988

By Still RF

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972

By Qisu W

The ground vibration produced by the bench blasts of a single hole and a row of two or three holes is recorded in an iron mine. Using the seismic signal generated by a single-hole shot as the source function, we have developed a computer program of a simulating ground vibration by bench blast. The reasonable delay time of blast in the iron mine has been discussed tentatively with the Fourmap invented by Anderson, D.A. The seismograms measured from the single-row blasts of two or three holes have shown the method of simulating vibration is feasible on the whole. For large scale production blasts, a combination of the vibration simulation and the high-speed photograph is used to choose the delay Time.

Jan 1, 1990

The papers to be presented in this Session show an interesting range of subject matter. Three discuss specific problems associated with existing mines, one deals with hydrogeological risk evaluation and one uses the impact of mine drainage on an aquifer to analyse a large-scale hydraulic parameter. Paper 1. Environment studies to determine the impacts of re-opening Banska Stiavnica-Hodrusa ore district in Czechoslovakia - Dusan Cababla - Marian Skaviniak. Future developments in established mining areas may have significant hydrogeological implications, especially where the existing mines are to be deepened. In turn this may have an impact in the area of the disposal of ever larger quantities of mine water, particularly, as is often the case, where the quality of this water is poor.

Jan 1, 1988

By S Paciornik, G Schinazi, M H. de Pinho Maur-cio, M B. Vieira, O da Fonseca Martins Gomes, D T. Wagner

Vale (previously CVRD û Companhia Vale do Rio Doce) evaluates the microstructure of sinters in order to understand their characteristics and behaviour in the agglomeration process, and the correlation with conventional quality parameters. Efforts on image analysis development are in progress between Vale and PUC-Rio in order to improve both the qualitative and quantitative evaluation of a representative portion of material. In the present work, digital microscopy techniques were developed allowing this kind of assessment. Employing a motorised and computer controlled optical microscope, low magnification mosaic images covering complete sinter samples were automatically obtained. The mosaics provide a powerful qualitative overview of the whole sample while allowing low resolution quantitative evaluation of the major phases. In addition, quantitative results for phase fractions were compared for the same sample regions at three magnifications (5x, 10x and 20x objective lenses). A single field (1 x 1) at the lowest magnification corresponds to mosaics of 2 x 2 and 4 x 4 images at the higher magnifications. The automated system allows perfect registration between the mosaics and the single image. Changes in phase discrimination were evaluated as a function of optical resolution, and phase fractions obtained by interactive segmentation of the image histograms were compared. While finer dark phases, eg silicates, were only visible with the best optical resolution, coarser phases such as haematite and pores were measured at all resolutions. For haematite, magnetite, ferrite and pores, the largest relative error in area fraction, between the images obtained with the 5x and 20x lenses, was 12 per cent. The results for silicate were less accurate with a relative error of 44 per cent. The results indicate that digital microscopy provides a flexible method for qualitative and quantitative evaluation of these materials.

Jan 1, 2008

Throughout the study phases (scoping, prefeasibility and feasibility) of new mining projects one is forced to work with and make predictions based upon limited date obtained from diamond and reverse circulation drill holes. These data are extrapolated to determine how much of the valuable metal is present in the ground, how it can be recovered it and the efficiency of this recovery. Mining methods to extract the ore are investigated with forecasts made regarding excavation stoping stability and performance in an attempt to optimise production. Extraction and use of rock mass data for use in characterising the mechanical behaviour of the rock mass is no exception. One often relies heavily upon the use of empirical charts developed over many years on hundreds of case histories based upon rock mass characterisation schemes. This is largely successful and indicative of what one might expect. However specific site characteristics can always play a significant role, and are not necessarily apparent in diamond drill core. Feasibility studies for the Favona orebodies indicated that the rock mass was generally poor to extremely poor, and that stoping conditions would be difficult in all of the orebodies for various reasons. A range stope performances were achieved ranging from very good to very poor and in some cases unexpected results were achieved. A comparison is made between what was actually achieved and what was expected since stoping commenced in 2007. Explanations are attempted for differences in stoping performance and, in some cases, unexpected results at the Favona underground mine are attempted.

Nov 25, 2010

Some mqre facts and inferences are presented in amplification of a recent paper on the geology of the Kalgoorlie Golden Mile stressing the volcanic origin of its rich gold ores, some of which are considered tobe exhalites. Previously unpublished and largely unmapped pyroclastic features in carbonated and chloritized, but not in amphibolitic, country rock are brought to attention. This applies particularly to the main host, viz. the relatively coarse-grained quartz dolerite greenstone (Q. D. G.), i.e. Golden Mile Dolerite, and gives more credibility to the spatial association of the rich Green Leader and telluride ores with bodies of sediments and tuffites occurring within, or adjacent to, Q. D. G. There may be an intrusive relationship with contiguous mafic amphibolites of doleritic origin, but this is not certain and can only be resolved by morecomprehensive mapping than in the past. Volcanic features have always been recognized in CalC Schist, i.e. Paringa Basalt, more so recently in the shape of coarse volcanic breccia.Iu the subsequent deformation of the gold ores since their inital emplacement there appears to be a structural parallel with some Canadian base-metal deposits, most of them of volcanogenic origin.

Jan 1, 1976

By Prosser A. P

A computer simulation is being developed for in-situ leaching of unbroken, Zn-Pb-Ag sulphide ore. Ferric chloride is the selected reagent. Experimental work showed that a diffusion control model of the kinetic aspects was better than a surface chemical reaction control model. Entrapped reactive grains were accessible to reagent in the samples tested. Precipitated sulphur did not seriously hinder the reaction.

Jan 1, 1987

The economic viability of many Southern African massive mining operations is threatened by excessive dilution. In many operations currently in progress, some stopes are experiencing as much as 115 per cent waste ingress reporting to drawpoints. This paper examines the magnitude, causes and types of dilution and presents a set of general principles for the control of dilution in massive stoping operations.

Jan 1, 2000

This paper outlines the manner in which legislative control for tunnelling and allied operations has evolved, detailing Victorian experience. It examines the concept of mine managers as it relates to the industry and attemps to illustrate its benefits. The Victorian experience in relation to fatal and serious accidents is examined in detail, particularly in the allied art of trenching and examines the Krings system of trench lining support which is hoped will catalyse an increase of engineering expertise in this area. The paper concludes by demonstrating that safety awareness is not incompatible with production efficiency or economic viability.

Jan 1, 1981