Search Documents

The Kingsgate molybdenite pipes are considered on petrochemical data and field occurrence to be, possibly, epi-magmatic plutonic offshoots grading into hydrothermal bodies. There is reason to believe that the ore is derived from a highly acid granite of type similar to that of the tin bearing areas of northern New England. The mineralogy, microtextures and paragenesis of the ore are discussed.INTRODUCTIONThe Kingsgate Mining Field is situated in steep, heavily timbered terrain 18 miles E.N.E. of Glen Innes and 430 miles north of Sydney. Bismuth and molybdenum ores were discovered at Kingsgate (Yarrow Creek) in 1877. Subsequently some 50 pipes were developed yielding tonnages which at the peak of operations, 1905 to 1920, rivalled production from the rich deposits of northern Queensland.Attempts to revive the field have been made periodically and small parcels of ore have been forthcoming.' During World War II demand for piezioelectric quartz again focussed attention on Kingsgate but twinning and other imperfections of the quartz prevented all but a minor exploitation of the otherwise noteworthy crystals of this locality.There is reason to believe that the ore at Kingsgate is not exhausted through exploration and mining costs would probably be high due to the capricious nature of the pipes and to the irregular distribution of rich ore shoots within them.

Jan 1, 1962

Copper waste dump leaching is growing in importance because of the.large tonnages (up to 250,000 ton/day) of low grade waste rock available from open cut mining of copper deposits and proof that controlled leaching of copper from such dumps can be profitable.Overburden or waste rock, ranging in size from large boulders to fines, is dumped as cheaply as possible on sloping sites. Copper is leached from the dumps by applying up to 12,000 gal/min of leach solution (a combination of spent solution from cementation and make-up water) to the top of the dumps by various techniques.Efliuent from the dumps is sent to a cementation plant for copper recovery.Factors which may be controlled, either directly or indirectly, to give a controlled copper content in the dump efliuent (usually 1-2 g/l.) are the cycle of operations (i.e. the alternate wetting and drying periods), thevolume of solution applied to the dump, pH, Fe2+ and Fe3+ content or redox potential, oxygen content, bacteria and their necessary nutrients, and temperature.Dissolution of oxide copper minerals appears to be mainly a function of acid concentration. Copper sulphide minerals need oxidation for dissolution to occur and this is accomplished by a combination of oxygen,ferric ion, and bacteria. Oxidation of pyrite, oxidation of Fe2+ to Fe3 +, and hydrolysis of Fe3+ are of some importance in leaching practice. The presence of gangue carbonate minerals is detrimental.Physical factors connected with penetration of solution into large rocks are important and the treatment of an individual dump usually extends over a period of many years. Recovery of copper from solution is usually achieved by cementation with iron (usually in the form of crumpled cans) but the use of sponge iron is becoming more important. Iron consumption varies from 1 to 4 lbiron per pound of copper. Preconcentration of the copper in the efliuent solution by solvent extraction followed by electrolysis may become a useful method.Application of dump leaching techniques to metals other than copper depends on finding an economic method of recovering the metal from solution...

Jan 1, 1967

The great problem at Port Pirie and many other lead smelters has always been to keep the lead content of the slags down to a low level. This has been done in the past largely by empirical methods, the lead content varying from less than 1 per cent to over 4 per cent, the more usual figure being something under 2 per cent. Subsidiary to this, but of major importance in the future, was the extraction of the considerable quantities of zinc in the slag. At this stage little was known about the constitution of the slags apartfrom their chemical composition. Some early work on slag constitution was carried out in the B.H.A.S. Research Laboratories between 1919 and 1921, but except for a microscopic examination of a few thin sections the greater part of this investigation wasdevoted to the recovery of the zinc content of the slag by leaching methods.In 1949, therefore, it was decided to initiate a programme of fundamental research into the constitution and properties of the lead blast furnace slags. The information thus gained would give a clearer picture of reactions taking place in the slag, both in the blast furnace and during dezincing.There was also the hope that these results would lead to improved industrial techniques resulting in smaller lead losses, and, taking the long-term view, to efficient methods of producing zinc from the slags.A series of investigations was therefore begun at various centres over a period of time. These were:1. A mineralogical examination of the slags by Dr. A. B. Edwards of the Mineragraphic Section, C.S.I.R.O.2. A study of the thermodynamics of various slag com...

Jan 1, 1956

Heap leaching for the recovery of precious metals is a comparatively new and rapidly expanding technology. The practical aspects of heap leaching are described and environmental and economic implications discussed.

Jan 1, 1984

By Pullen G, Rose M

Continuing Professional Development (CPD) is not just a catch-cry. It is an essential component of every-day life in many professions, including accountancy, law and public administration. Without realising it, many other professions are undertaking CPD activities in an un-structured way, including mining, metallurgy and geology. Examples include Annual and technical conferences of The Institute, Branch-level technical meetings and in-company training and development programmes and technical exchanges. Whilst approaches to date have undoubtedly helped keep the Australian mining industry at the forefront of mining technology, one cannot presume that technological development will stand still. To meet this challenge, human resource development must keep pace, not only to optimize utilization of technological developments, but more importantly to develop firm bases from which new products, processes and technologies can be developed within Australia.

Jan 1, 1989

By Hargraves AJ

Pre-drainage experiments have been conduct- ed at Appin, Cook, John Darling, Leichhardt, Macquarie, Metropolitan and Moura No. 2 Collieries. Appin (550 m deep) experiences particular gas problems in development drivages, and the almost pure CH4 seam gas makes difficult tiro compliance with statutory maxima in intakes and returns. Patterns of 43 mm diameter drain- a,.;e holes drilled ahead and laterally into virgin coal have improved gas conditions in working places and have allowed tolerable advance rates. Cook, Leichhardt, Metropolitan and Moura No,. 2 Collieries have experienced gas and stress phenomena ranging from conical bursts less than one tonne to full scale instantan- -us outbursts of hundreds of tonnes with tens ,f thousands of cubic metres of seam gas. Gas ~Irainage experiments with patterns of holes up a,, 200 mm diameter have been undertaken with ;,;siness monitors on the coal to establish .lative effectiveness. Incremental flows into mg 43 mm diameter boreholes have investigated drainage patterns relative to length, and at comparative incremental flows have nlicated lowered permeability zones at stress ,.,utments. In some CO2 seam gas areas where iammability problems are reduced to perhaps ii, but where outbursts proneness is increased,

Jan 1, 1982

By G C. Bolton

Experiments were conducted to access the feasibility of removing zinc from lead slag by sulfation or chlorination or both. Gaseous sulfation with sulfur dioxide and oxygen released only 50 per cent of zinc even under the most severe conditions. Sulfation with concentrated sulfuric acid by a fast-leach process released 95 per cent of zinc while pug-roasting released a maximum of 78 per cent of zinc. Chloridization with NaCl in the presence of sulfating gas released 50 per cent of zinc, while direct chlorination with chlorine gas and oxygen released 85 per cent of zinc and 100 per cent of lead in a chloride condensate containing little impurities.

Jan 1, 1980

By H Hy÷tyniemi

In this paper multivariate data analysis performed on a new multi-camera system implemented to zinc flotation circuit of PyhSsalmi mine is presented. Image-analysis-based system was developed to take advantage of the commonly known fact that the changes in the flotation process are reflected to the visual appearance of the froth surface. Most often the changes are seen first in the froth and later in other process measurements. The image variables are already utilised in closed loop control and considerable savings are achieved with the current setting, but the results coming from the separate cells are used individually. This is clearly not the optimal way to take advantage of the many measurements coming from different locations of the process. A better approach would be for example to use the measurements coming from the early stages of the process to predict the behaviour (or improve the quality of measurements) in the later stages. The methods described in this paper are aimed to improving the situation in this sense.

Jan 1, 2005

In a country richly endowed in mineral wealth, Climax Arintco Mining Corporation's ICAMC) Dinkidi porphyry Au-Cu deposit in Nueva Vizcaya, Philippines, represents the most significant mineral discovery in this country in recent times. The deposit is located within a belt of young intrusive and volcanic rocks in the Sierra Madre mountain chain of north Luzon, a region previously unassociated with porphyry -style mineralisation.Since 1989, drilling of the Dinkidi deposit has outlined a resource of 124 million tonnes of 1.0 g/t gold and 0.4 per cent copper. Regional exploration throughout CAMC's 37 000 hectare FTAA has identified a further 16 potential porphyry-related deposits.

Jan 1, 1997

The Rotary Kiln at TeKumi was commissioned in February 2002. The process involves burning limestone at 1000 - 11 000¦C to produce a burnt lime (CaO) product. This paper describes the design and installation of a trifoil system to improve the energy efficiency of the kiln. An energy balance showed that 32 per cent of the energy was being lost through the flue gases, compared to 5.8 per cent in shell losses and 2.5 per cent lost as heat in the product. The trifoil proved to be the best way to tap the energy from the flue gases. Drying tests showed that a trifoil improved the drying time of limestone by 37.5 per cent, compared to only 25 per cent for a lifter system. The trifoil system increases the surface area for heat transfer in a Rotary Kiln by 180 per cent. The overal energy efficiency of the Rotary Kiln was improved by 15 per cent, resulting in a 15 per cent increase in production and an 80¦C reduction in flue gas temperature. This has reduced dust build up in the ducting while reducing maintenance costs through a reduced fan speed. The trifoil hub was designed with tooths at the centre to prevent shifting. Each trifoil leg has an anchor block on the down side to prevent downward movement of the trefoil legs.

Jan 1, 2003

By Adranyl W. W

Sub-level caving with bottom ore drawing has gained wide acceptance in rich, soft, low magnetic iron ores because it provides moderate ore dilution and ore losses. The main problem here is the high rock pressure exerted on sub-level drives situated in the sub-level sill pillars. To reduce this effect, the ore block is divided into panels. This paper illustraes the method of determining the maximum panel width providing low maintenance cost of sub-level drives.

Jan 1, 1995

By D J. Bradshaw, E M. Wightman, C L. Evans, B Triffett

During the commissioning phase of Prominent Hill, periods of reduced recovery were experienced with higher-grade ore blends. This was unexpected and as part of the process to identify the cause, surveys were conducted in May 2009, with two different ore blends (copper grades: 1.94 per cent Cu (blend 1) and 2.49 per cent Cu (blend 2)). Metallurgical performance was assessed in terms of rougher recovery and grade with consideration of both pulp and froth effects. In addition, hydrodynamic measurements (gas hold up, bubble size, superficial gas velocity) as well as measurements of bubble load and top-of-froth grade were taken during the surveys and full mineralogical assessment of selected streams completed to characterise the nature of the differences. The metallurgical results showed that the lower performance was obtained with blend 2 which contained the higher amount of chalcocite and was higher-grade. Analysis of the survey data showed that for both ore blends more than half of the copper loss occurred in the +38 ¦m size fractions. Almost 30 per cent of the copper in the +38 ¦m fractions that reported to the rougher tails during processing of blend 2 was liberated compared to less than five per cent for blend 1. Additionally almost 60 per cent of the copper in the +38 ¦m fraction of blend 2 was chalcocite compared with approximately 20 per cent in blend 1. This paper discusses the sensitivity of the chalcocite-to-surface chemistry effects causing marked reductions in recovery either through reduced pulp recovery or froth phase (detachment) effects. The reagent suite and operating conditions were subsequently changed and the recoveries increased substantially and the sensitivity to ore changes eliminated. It should be noted that subsequent optimisation work, which focused on recovery improvement, has led to copper recoveries of over 90 per cent being achieved.CITATION:Bradshaw, D J, Wightman, E M, Evans, C L and Triffett, B, 2012. Characterising the reasons for the difference in performance of two ore blends in early processing at OZ Minerals Prominent Hill Operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 273-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By G S. C Murray

Major mining projects are developed with the assistance of lending institutions who provide hundreds of millions of dollars in funding over several years, and of course expect those funds to be returned with interest. Two Australian banks have adopted the Equator Principles, an emerging financial industry benchmark for assessing and managing environmental and social risk in project financing. Project financiers have encountered environmental and social issues that are both complex and challenging, particularly with respect to projects in the emerging markets of Asia-Pacific and elsewhere. There are many recent and historical examples of failures by resource companies to effectively manage their environmental, social, safety and security risks, some of which have caused the project to fail completely, and some of which have caused the temporary cessation of production. These events put the financial institutionsÆ funds at risk through inadequate management capacity and non-compliance adversely affecting the ability of the borrowers to repay the loans. They can also reflect adversely on the reputation of the lending institutions. In assessing these risks, lenders are increasingly looking at the track record of the borrower in its country of origin and in other countries where it operates. Lenders are wary of companies that have one standard for operations in a developed country, where the regulatory environment may tightly control what they do, and another standard for operations in countries where the regulatory regime is perhaps less stringent. Lenders may require environmental and social reviews or audits to be conducted on their behalf by competent third parties prior to a loan being approved, and annually over the life of the relationship. The mining industryÆs concept of the unwritten æsocial licence to operateÆ is highly relevant in relation to the delivery of community benefits that are sustainable post-mine closure. This paper provides examples of recent practices that support financial viability and sustainable development, as well as examples of some failures that have put lenders at risk.

Jan 1, 2007

By K Williams

Marvel Loch South Pit has had a number of stages of open and underground mining activities before acquisition by Sons of Gwalia. The historical pit had achieved a completed pit depth of 150 metres and the shaft and decline mine had reached approximately 220 metres in depth using open stope mining methods. The various mining methods reflect the various economics and industry practice at the time. The South Pit ore zones are medium grade (~2.5 g/t) but have a regular geometry and large tonnes per vertical metre. A number of studies have been completed up to a pre-feasibility stage looking at options to extend the pit depth and to lower the unit cost of gold production. The options considered were the re-optimisation of the pit to determine further cutbacks or the innovative use of an in-the-wall ramp. The in-the-wall ramp (tunnel) would permit the removal of the in pit ramp to expose additional ore that was within the footprint of the ramp design and to provide the opportunity to increase the final pit depth. Similar mining method has only been used at Three Mile (Coolgardie, WA) and Chalice Mine (Norseman, WA). The tunnel would serve as a gateway for further extension of the south mine and the central ore zone via underground mining methods. The ultimate depth of the South Pit has been extended to 310 metres below surface and significant additional ore has been recovered. This paper will give an insight into the various studies to optimise the Tunnel mining method, the determination of the various tunnel dimensions, and the phases of mining to arrive at the completed design.

Jan 1, 2003

The output of Dexin Pit Copper is up to 33 million tonnes a year and the final depth is more than 500 m. As a cost reduction measure, the in-pit crushing and conveying system has was introduced to deliver ore from the pit to mills. This paper describes the in-pit crushing and conveying system, and highlights the optimum level where the shovel-truck haulage system transfers into In-pit Crushing and Conveying system, relocation of an in-pit crushing system, and includes the impact of the transferring point when the costs change.

Jan 1, 2003

By M Dohm, L Pretorius

This paper provides a brief historical background to the approximately 12-year project that led to the revision of rope selection factors in the South African regulations, thus providing the ability to hoist economical payloads from single lift ultra-deep shafts. The efforts over the past 20 years have led to the revision of the legislation pertaining to rope selection factors, the redesign of rope constructions to meet the required duties associated with ultra-deep shafts, codes of practice for the design, operation and maintenance of winding plants, and a code of practice for the condition assessment of winder ropes. As a consequence the Moab Khotsong ultra-deep hoisting system could be developed and installed, with the assurance of predictable performance. Access to deep orebodies by means of single lift, ultra-deep shafts has a critical impact on the life cycle costs and efficiencies of ultra-deep mining complexes. A brief description of the main components of the hoisting system at Moab Khotsong is presented. An in-depth review of the development process applied to ensure a stable, safe and cost-effective rope construction for the ultra-deep Moab Khotsong shaft follows. The paper concludes with an overview of the experiences gained during the installation and commissioning phases of the winder, as well as operational and maintenance issues.

Jan 1, 2005

Mining regulatory authorities worldwide mandate frequent inspection of winder ropes used in shaft-equipped underground mines and ski lifts. Visual inspections are effective in identifying and assessing the type and severity of damage found in the exterior of the rope. In addition, electromagnetic or permanent magnet-based methods are used to identify broken wires, corrosion damage and other anomalies that occur anywhere within the core of wire ropes made of steel, which is a ferromagnetic material. The magnetic methods yield the loss of metallic area due to wire breaks and other damage in the ropeÆs section as well as local flaws that give rise to discontinuities in the magnetic field. The quantitative measurement of the loss of metallic area is indirectly related to the loss of breaking strength that is commonly used as a rope discard criterion. The ropes used in a mine winder in the Goldfields of Western Australia are inspected using Meraster 120B permanent magnet-based rope tester and their condition is assessed against published discard criteria.

Jan 1, 2003

THE Great Fitzroy Mines Limited, comprising an area of 183 acres, and held under lease, are situated at Mt. Chalmers, within the Cawarral goldfield, 18 miles from the city of Rockhampton, Queensland, on the Rockhampton-Yeppoon railway.The nearest railway station i; Mt. Ohalmers, distant about half a mile from the mine, with which it is connected by a fairly good road. The outcrop of the ore-body consists almost entirely of ironstained quartzite, no sign of copper being visible. The outcrop and its immediate vicinity have been worked intermittently for gold during the past :fifty years, the ore being amenable to battery treatment.About twenty years ago a company was formed to prospect this outcrop, and work was commenced by driving an adit, but the results proved disappointing, and work ceased. Later a party of prospectors sunk a winze from the adit level, which has sincedeveloped into wh~t is now known as the North shaft. The property was afterwards prospected by Messrs. Oharley and Osborne, who continued sinking the winze, meeting with sulphides at a depth of about 120 ft.The Mt. Chalmers Copper Mining Company was formed to work the property, and smelting operations started on a small scale. These, however, met with ip.different success, and the property was again abandoned.

Jan 1, 1911

The Agnew Mine No. 1 Ventilation Shaft is the largest diameter shaft blind drilled in a hard rock mining environment. The selection of this method of shaft development was based on achieving an accelerated mine development and exploration programme. Drilling the shaft from a pre-sink depth of 73m commenced on March 22, 1982 and the shaft was stopped due to rig structural problems at a depth of 750m, 280m from the designed depth, on February 12, 1983, 137 days behind schedule. While problems with rig mechanical availability, cutter life and lost drilling tools in the hole hindered progress and escalated costs, penetration rates above prediction were achieved and both the speed and safety aspects of the method were well demonstrated.

Jan 1, 1983

By G N. Phillips

Global annual gold production has been remarkably constant over the last decade at ~2500 t/a3. The major producers today are China (annual production over 350 t and rising), Australia (250 t), USA (240 t), Russia (200 t) and South Africa (190 t and falling); these figures are representative of recent years but approximate. Demand from jewellery, investment, industrial and dental uses has been in excess of mine production for the last decade, by approximately 1000 t/a.Ongoing exploration is the life-blood for gold mining, and more so than for many other metals. Explorers consider sovereign risk, security, labour costs, commercial terms, land availability and inherent geologic prospectivity to determine where to focus their activities. Exploration success over the last decade has been shared by established major producers like Australia, Canada and USA, several countries in West Africa, and many parts of the Pacific margin. Although gold-only deposits have dominated world gold production historically, the gold-plus types, especially copper-gold, are becoming more important.Australia experienced a major period of exploration success from 1979 that has led to annual gold production rising from 17 t in 1979 to 250 - 300 t/a recently. Today, Australia has economic demonstrated resources of over 9000 t Au, which has risen progressively from 220 t in 1979. The majority of production has come from gold-only deposits in the Yilgarn craton in the southern half of Western Australia, but there are a few large Proterozoic deposits in central Australia including Olympic Dam, Telfer and Starra, which are mostly gold-plus types with copper and gold. Large goldfields in the younger host rocks of eastern Australia include the gold-only deposits of Victoria and North Queensland, and gold-plus deposits of New South Wales.CITATION:Phillips, G N, 2013. Australian and global setting for gold in 2013, in Proceedings World Gold 2013 , pp 15-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013