Search Documents

By C. P. Lawhon, J. P. Simpson, W. M. Evans

Recent efforts to design drilling fluids for increased drifting rates have confirmed some laboratory results of other investigators, but have also produced additional data that should be considered. These data were obtained under controlled test conditions using a microbit drilling machine. Clays and some polymers have previously been reported to cause reduction in drilling rate. Recent data have shown that under laboratory conditions, suspensions of a single day or polymer have sometimes given faster drilling rates than when water was used. Measurements have been made of clay suspensions and polymer suspensions comparing filtration (I) under API conditions, (2) while drilling with temperature of 150F and differential pressure of 1,000 psi and (3) under dynamic conditions after drilling. Some correlation between instanraneous filtration (white drilling) and drilling rate has been observed. INTRODUCTION Several papers have been presented that related drilling fluids to penetration rate. Generally, it was found that a decrease in the solids concentration resulted in significant increases in the drilling rate. Of course, this change also resulted in a decrease in the viscosity of the drilling fluid.' Conclusions from investigations by this laboratory are in agreement. Data have shown that of the simple mud measurements commonly made at the drilling rig (density, plastic viscosity. yield point, API filtrate and total solids), only the density and total solids have a significant relationship to the drilling rate in Berea sandstone when attempting to correlate a single mud property individually.' More recent drilling rate experiments have been designed to study (1) effects of individual clays and polymers on drilling rates in Berea sandstone and Lueders limestone, (2) the relationship between drilling rate and dynamic filtration as measured after drilling and (3) the relationship between drilling rate and dynamic filtration as measured during drilling. Data show that drilling rates are dependent upon type and concentration of particles, type of formation and filtration of the individual fluids while drilling. Mud pressure: pressure of drilling fluid as measured after leaving the drilling chamber (Fig. 1). This is taken to be approximately the mud pressure just past the bit and at the face of the formation. Terrastatic pressure: pressure representing weight of overburden. Formation pressure: pressure of formation fluid as measured at outlet of drilling chamber (Fig. 1). This is taken to be approximately the pressure of fluid in the interstices of the formation. Differential pressure: difference between the mud pressure and formation pressure. LABORATORY EQUIPMENT AND TESTING PROCEDURE The drilling equipment was described in two previous publications."' Main components are a drilling chamber, filter-heater, rotary drive and variable-speed circulating pump. Auxiliary pumps supply pressure boosts for the mud, terrastatic and formation pressures. All equipment is designed for 15,000 psi and 500F. Capacity of the circulating system is approximately 7 gal. The mechanical design was facilitated by moving the rock down onto the bit. Data collected with this design should not differ from that obtained by a normal design where the bit moves into the rock. Drilling fluid is pumped through 50 ft of ID pipe coiled in an oil bath, enters the rotary shaft at a right angle and is pumped through the jets on the bit (Fig. 1). Most of the drilled solids are extracted by a screen mounted in the circulating system on the suction side of the pump. Data reported in this paper were obtained by controlling these parameters: mud pressure, 5,000 psi; formation pressure, 4,000 psi; terrastatic pressure, 5,000 psi; force on bit, 1,000 Ib; formation, Berea sandstone and Lueders limestone; flow rate, 7 gal/rnin; bit, 11/4-in. diameter with two 0.078-in jets; mud temperature. 150F; and rotary speed, 60 rpm. Mud pressure was controlled at 5,000 psi, thus giving a differential pressure of 1,000 psi even though the fluid densities varied. Cores of 3%;-in. diameter and 8 in. long were selected from quarry blocks to provide some control of grain size distribution, permeability and porosity. A 2-in. section was cut off each core and a I -in. diameter plug was taken from this section. Permeability to 5 percent by weight sodium chloride solution was determined and the large cores were

By W. C. Ellis, E. S. Greiner

WHEN metallic materials are deformed plastically, the process may be considered as one in which hardening and recovery occur simultaneously. The net hardening is that produced by deformation in the absence of recovery lessened by recovery during and immediately following deformation. Strain hardening takes place through movements of large groups of atoms acting to a degree as an entity. A complex microstress system is developed. Recovery is a diffusive-type process involving single atoms or, at most, only a few atoms in concerted action. This is accompanied by elastic strain relaxation. Recovery is strongly temperature-dependent. The driving energy for the process resides in thermal fluctuations of the atoms augmented by the energy of the stress field producing the deformation, and by that produced by the deformation. At very low temperatures recovery is essentially absent, or very small. At high temperatures in the hot working range, recovery is so rapid that deformation results in no appreciable net hardening. The interplay of strain-hardening and recovery results in differing end structures depending on the temperature and the strain rate of the process. For example, there is a prominent difference in the spacing of the slip markings and in the detail of X-ray diffraction patterns. High temperatures and slow strain rates favor a wide spacing of slip markings and sharp reflections.',' This suggests that change in rate of the recovery concurrent with deformation modifies to a degree the manner of the deformation. Different slip systems may operate. For very slow rates, the mechanism may, as has been suggested, differ from that of "classical slip." In the experimental work that follows the findings will be interpreted from the point of view developed in this section. Recovery and Electrical Conductivity Electrical conductivity is a sensitive indicator of the state of strain in a material3' * and was used in this investigation. The materials studied in wire form were: OFHC copper, a high purity (99.99 pct) and 2s grade aluminum, and grade A nickel. Wire annealed and initially 0.050 in. in diam was drawn through diamond dies in a simple holder maintained at 25", —75°, or — 195°C. Precautions were taken that for each material all conditions of drawing were the same except the temperature. Electrical resistivity was measured for each condition at 20°C. This was done as soon as practical after drawing to minimize possible room temperature recovery. The data for the four materials are plotted in Fig. 1 in terms of the change in resistivity for drawing at the several temperatures. The effect of temperature of drawing on the increase in resistivity is most pronounced for copper. Drawing at 25°C to 80 pct reduction in area increases the resistivity approximately 2 pct; drawing at —195°C to the same reduction increases the resistivity about 6 pct. The increase in resistivity" & in this metal is due to extra scattering of conduction electrons originating in the lack of orderly arrangement of the atoms induced by the deformation process. It has been suggested

Jan 1, 1953

Discussion of the paper of Blarney Stevens, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 1913, pp. 1285 to 1303. F. L. GRAMMER,Leesburg, Va. (communication to the Secretary*):¬ Mr. Stevens refers to an explanation of parallel jointing by W. 0. Crosby, which I noted when reading one of his excellent text books. It seemed to me earthquakes were not a satisfactory explanation, and I looked up several authorities; but I never realized how small the usual amplitudes were until Mr. Stevens presented his paper. Several letters to the U. S. Geodetic Survey showed me there were very few records of tidal movements of earth crust in the United States. Altitude and latitude would be influencing factors; but this diurnal movement must exceed earthquake amplitudes, besides being more nearly universal. My inquiries brought the answer that the major directions of jointing had not been extensively tabulated. If major directions of jointing were recorded-with notes as to angle with mountain chain, or North Star, and distance between joints, with nature of rock and maximum and minimum tidal up-heaval-some interesting relations might be made manifest.

Jan 11, 1913

By H. Van F. Furman

As the cyanide-method for the extraction of gold from ores is extensively used in the United States and elsewhere, and appears destined to prove a factor of increasing importance in the metallurgy of gold, a description of the latest laboratorymethods may prove of interest. The history of the development of the process in the United States has been analogous to that of all new processes. Many failures are to be recorded and a few successes. It is the opinion of the writer that, had the following simple tests been better understood, many of the failures would not have occurred, and we should probably have a larger number of successful plants in operation. While the process is not simple, but requires a high degree of chemical and engineering skill, the determination of the adaptability of an ore to the method is generally not difficult. While the laboratory-results will not always coincide with the actual results obtained in the mill, they will serve as a guide and control on the working of the mill, and mill generally suffice to determine if the ore can be

Jan 1, 1897

Both drilling and production in Rumania showed increases in 1934 over 1933. The drilling totaled 1,138,000 ft. and production 63,500,-000 bbl., being increases of 50 and 15 per cent, respectively. During the year production gradually increased from 155,000 bbl. per day in January to 180,000 bbl. in September, and then declined slightly to the end of the year. The increases were largely due to competitive drilling in the Gura Ocnitei field (including west extension to Viforata). Wells completed during the year totaled 238, of which 215 were oil producers. The outstanding development of the year was the discovery by Steaua Romana of what appears to be a major field at Bucsani. Other important discoveries were a three-mile west extension of the Gura Ocnitei fault to Viforata and a five-mile east extension of the Moreni field to Calinesti. Strictly speaking, the latter cannot as yet be called an extension. Oil sands have been corded in the Meotic, and in all probability production will be established in 1935. The Calinesti discovery greatly restricts the unproved area between Moreni and Baicoi, and the probabilities of

Jan 1, 1935

By E. T. Cox

The Albion phosphate-district embraces a territory about 4 miles wide and 6 miles long, in a northerly and southerly direction, situated in Levy county, Florida. The Florida Central and Peninsular railroad, running from Fernandina, a shipping port on the Atlantic, to Cedar Keys, on the Gulf of Mexico, passes through the center of the district. The post-office and railroad station is in the town of Albion. The physical features of the district present a series of white aqd whitish-gray sand-hills and ridges, rising about 130 feet above tide-water. The sand lies in a loose body, like that seen on the ocean beaches. In places the hills have the appearance of sand-dunes, such as are seen along the Platte river, in Nebraska. Beneath the sand are found the phosphate-deposits, which are partially exposed in places, but, for the most part, lie buried to a depth of 15 feet and more. In this district the phosphate is designated as " hard rock,"

Jan 1, 1896

By Richard E. Gray, William S. McCann, Robert C. Speck, Robert W. Bruhyn

Subsidence of the ground surface is the inevitable result of high recovery longwall and room and pillar coal mining operations. Up to now, U.S. research into this phenomenon has been concerned primarily with documenting the magnitude and extent of ground movements and prediction of the attendant ground strains through traditional ap¬proaches that have been developed in Europe and the United Kingdom. Preoccupation with ground strain prediction has, unfortunately, diverted attention from the more meaningful objective of predicting the severity of damage to structures at ground surface and the prob¬able cost to repair such damage. An attempt has been made to rectify this situation by reviewing in detail one hundred thirty four cases of subsidence damage to dwellings above active mines in western Pennsylvania, identifying the types of damage and the circumstances under which damage took place. The data reveal that damage to dwellings virtually always includes basements in addition to the readily apparent effects to the superstructure. In 90 percent of the subsidence cases, more than half the repair cost is associated with damage to subgrade components. A damage classi¬fication system has been devised that relates observed damage to severity and repair cost in a uniform manner for conditions in the Northern Appalachian Coal Field. Damage severity has been examined in the context of depth to the mine, the character of the near¬ surface overburden materials, mining type and other parameters.

Jan 1, 1983

By K. Osseo-Asare

The presence of carbonaceous matter in gold ores presents a two-fold problem: (1) The poor release of gold from the carbonaceous matrix and (2) the uptake of dissolved gold by the carbonaceous leach residues. A critical review is presented of the published information from various parts of the world pertaining to the nature of the carbon-containing components of these ores and their different roles in the gold extraction process. Included in this paper are new results based on the authors' research on carbonaceous ores from the Prestea goldfields of Ghana. Methods for isolating and characterizing the carbon-containing materials are given and a discussion is presented of the interaction of the carbonaceous ores as well as the fractionated components with aurocyanide solutions. Emphasis is on basic physico-chemical phenomena, investigated with the aid of X-ray diffraction, infrared spectroscopy, adsorption, and electrophoretic mobility studies.

Jan 1, 1984

By Henry F. Collins

The following notes on the cheap milling of a soft lowgrade ore-body in the State of Chiapas, Mexico, may be of interest. The ore-body in question was worked, not by itself, but incidentally in connection with a large extraction of concentrating-ore; and one 10-stamp battery of a 30-stamp mill used for re-crushing tailings, and provided with copper-plates, was set aside for the treatment of this particular ore, of which, during a period of 17 months, 10,274 tons, of 2240 lbs. each, were handled. Description.—The ore-body collsisted of that portion of a mass of decomposed garnet-rock of igneous origin, which, near its contact with another igneous mass, composed chiefly of the mineral wollastonite in a nearly pure state, had been permeated by solutions, depositing irregularly, throughout it, quartz, chal-

Jan 1, 1902

By Ralph Wilcox

THE diamond drilling of certain characters of unstable rock forma-tion, as, for example, the copper-bearing schists of the Miami district in Arizona, is rendered most difficult by what is known as " caving" of the sides of the drill holes. As this caving is very greatly increased by the action of flowing water, it occurred to me, after experiencing a great deal of difficulty with caving in diamond-drill holes which I was drilling for the Miami Copper Co., that if I could substitute air for water, much of the caving-with resultant difficulties, such as decreased speed of sinking and increased consumption. of diamonds-would be overcome. After some experimenting, I found that it was perfectly practicable to substitute air for the water; forcing the air down the hollow rotating rods in the same manner as is done with water, the air passing out around the bit, which is thus cooled, and ascending on the outside of the rods to the collar of the hole, carrying the borings in just as satisfactory a manner as had been done by the water, but without the accompanying destruction or caving of the sides of the drill holes such as had been so generally experienced with the water. When water was encountered in the drilling this water was forced up to the collar just as it would have been had water been used in the .drilling, but with the correspondingly decreased flow there was relatively less washing or caving of the sides of the drill holes. The only change necessary in the arrangement of the drill is that a cross instead of a tee is used at the collar of the hole. A tightly woven jute bag is attached to one arm of the cross, for collecting and filtering the sample; and when drilling in dry ground a jet of water is attached to the opposite arm of the cross, to collect the dust and wash down the sample into the bag. The rods rotate through a stuffing box attached to the upper opening of the cross. The distention of the jute bag by the issuing air indicates the operating conditions as sufficiently as did the flow of water when using water in the drill hole.

Jan 10, 1913

By Ian J. Smalley

"Quickclay is an extreme case, it is by far the most mobile of all the common solid materials on the earth's surface. It has both a high water content and a mineral texture that allows it to flow with the utmost ease. A mass of quickclay that has lain undisturbed for thousands of years can be jarred into motion by any sudden shock." The quotation is from the paper by Kerr called, "Quickclay," which was published in Scientific American in 1963. This was probably the most widely read paper on quickclay ever published. It was reprinted by Fred Betz in his Benchmark collection on Environmental Geology (BM 25), A quickclay is an extremely sensitive soil. The sensitivity parameter is produced by dividing the undisturbed shear strength by the remoulded shear strength. If a value greater than 50 is obtained, then the soil can be classified as a quickclay. True quickclays are characterized by a very low remoulded strength of the order of 0.5 kPa. The classic quickclays are found in Scandinavia and Eastern Canada, but the 1964 Alaska earthquake revealed a considerable quick¬clay deposit underlying the town of Anchorage. This was discussed in a classic paper by Kerr and Drew in Engineering Geology in 1967. The Kerr views on quickclays were perhaps most clearly expressed in the paper with Liebling in Geol. Soc. Amer. Bull. in 1965. They suggested that the major critical conditions which contribute to quickclay movement are: substantial quantities of layer lattice silicates of colloidal size (about 40% or more by dry weight), sub¬stantial pore water (44%), a reduction in electrolyte concentration below 5 g/l of salt, and addition of a dispersant. There is still discussion and disagreement about the nature of quickclays and the mechanisms of quickclay slides; the "clay mineral"-based views favored by Kerr still find support, although an alternative "primary mineral" view suggests that it is the finely ground primary minerals

Jan 1, 1985

By Charles L. Mantell, B. G. Shah

SINCE the beginning of the industry, commercial electrolytic manganese has followed the Shelton patent' among others, which called for the addition of sulfur dioxide in controlled amounts, to a purified manganese sulfate-ammonium sulfate at a controlled pH. Every attempt to eliminate sulfur dioxide additions has resulted in operating difficulties, chiefly solution of the deposited metal and lowered current efficiencies. Many replacements for sulfur dioxide have been proposed and studied, chiefly sulfur compounds, urea, thiourea, and proteins similar to those employed successfully in copper refining. It has been suggested that sulfur dioxide is a re-ductant for higher-valence manganese compounds, or that it is reduced by manganese metal in the deposit to hyposulfites or its compounds, and that these might affect the cathode film or the deposition potential, or the overvoltage of manganese. The additives were studied following the method of Mantel1 and Ferment2 who determined the feasibility of current-potential curves as an analytical tool for monitoring manganese elec trowinning solutions for metallic impurities: nickel, cobalt, silver, copper, zinc, molybdenum, cadmium, magnesium, and sodium. The individual effect of each on the standard polarization was determined for a range of concentrations. Not all affected the polarization curve; cadmium, magnesium, and sodium had no effect. Nickel, cobalt, silver, copper, and zinc yielded a correlation between transition current and concentration of impurity.

Jan 1, 1968

By William E. Bruce

This paper is intended to provide an improved understanding of natural draft (natural ventilating pressure) and the effect of natural draft on underground mine ventilation circuits. Attention is focused on measurement of natural draft pressures during ventilation surveys in mechanically ventilated mines and on different methods for modeling natural draft using the measured data. A number of examples are presented which utilize data collected during absolute air pressure surveys made by personnel of the Ventilation Division of the Mine Safety and Health Administration's Safety and Health Technology Center, Denver, Colorado. Examples are used to illustrate how the data from absolute air pressure surveys may be interpreted to determine whether natural draft pressure is present and what its magnitude is. In addition, two different methods are described for mathematically estimating the magnitude of the natural draft pressure. Comparisons are made of results obtained using the different methods. Different procedures are described for modeling natural draft using the MSHA-modified Penn State computer program. Use of the routines is described and illustrated relative to drafts that aid or oppose the mechanical ventilation system. Tabulations of results facilitate comparison of outcomes obtained using the different modeling procedures.

Jan 1, 1982

By Morris Muskat

TEe method of R. W. Moore' for determining subsurface interfacial depths by means of integrated curves of apparent resistivity has been analyzed theoretically. It is found that the only unique tangents that can be drawn to such curves are the asymptotes at infinite electrode spacing and the tangents through the origin at vanishing electrode spacing. Explicit expressions have been derived for the relationship between the electrode spacing at the points of intersection of these tangents and the thickness of the surface strata as a function of the conductivity parameters for the two-layer and three-layer earths. It is found that in all cases the electrode spacing at the points of intersection will exceed % of the thickness of the surface layer, and may even become indefinitely large as the resistivity of the deepest layers increases as compared with that of the surface layer. These results do not agree with the empirical findings of Moore that the intersection of the tangent lines fall at an electrode spacing very approxirnately equal to the thickness of the surface layer. Introduction In a recent paper, R. W. Moore1 proposed a new method for the analysis and interpretation of earth-resistivity measurements. This consists essentially in plotting against the electrode separation of a Gish-Rooney system the integral of the apparent resistivity with respect to the electrode spacing, and observing the breaks in the integral curves. Specifically, tangents are drawn to the various segments of the integral curves, which show appreciably different slopes, and the intersections of these tangents are used as indications of the depths of the various underlying strata. By numerous examples Moore has shown that the electrode separation at the first intersection so found agrees very closely with the depth of the bottom of the surface layer. Moreover, in a number of instances the intersections for greater electrode spacings seemed to correspond to the depths of deeper beds. From a strictly empirical point of view, the procedure proposed and demonstrated by Moore appears to be particularly interesting because of its simplicity as well as its apparent accuracy, Moreover, such a simple method would be especially valuable in view of the well-known difliculties heretofore encountered in the quantitative interpretation of resistivity data. It therefore seems appropriate to attempt a mathematical analysis of the problem to see whether the integral method of Moore has a sound basis. Such an analysis is presented here. Even on cursory consideration, it is clear that the remarkable successes observed by Moore in the application of his method are indeed surprising. For it depends upon the determination and choice of the slopes of smooth and continuous curves, which by their nature must show even more gradual- variations than the original apparent-resistivity plots that are already so difficult to interpret quantitatively. It is well established, of course,

Jan 1, 1946

By T. F. Witherbee

(Read at the Amenia Meeting, October, 1877.) THE subject of an article in the Engineering and Mining Journal for October 13th, 1877, namely, Blast Furnace Treatment of Silicious Iron Ores,, is of great interest to myself, and doubtless to many others who have been troubled with a seemingly unaccountable percentage of silicon in their pig iron. It is to be regretted that the author of the article did not give us complete details of his charges, and thus prevent a possibly fatal error in the very beginning of the discussion of the points raised in his communication. As it now stands, I think we will have to fall back upon the statement that, "every conceivable mixture of fluxes and ores (A and B) has been used." Let us first, in order to simplify the calculations, do with the

Jan 1, 1878

By R. M. Waterstrat

X-ray diffraction and metallographic examination of binary Mn-rich alloys with Ti revealed the presence of intermediate phases in this system. A binary R phase has been identified and also a phase having an a-Mn type structure. The X-ray pattern of the phase TiMn3 is presented and a tentative phase diagram for the Mn-rich portion of this binary system has been constndcted. MANGANESE-rich alloys with titanium have been subjected to thermal analysis at temperatures down to 1100°C by Hellawell and Hume-Rothery.1 Their results indicate the existence of an intermediate phase TiMn3 in this binary system. This phase appears to coexist with the Laves phase TiMn2, and with terminal solid solutions based on the allotropes of manganese, at least down to 1100°C. The above investigators did not attempt to determine the crystal structure of this phase, however. Since, by analogy to the binary systems Mn-V and Mn-Cr3 one might expect to find a phase in this region of the diagram, it seemed desirable to obtain X-ray diffraction patterns of alloys in the concentration range in question, in order to ascertain whether the sigma phase or related structures occur. EXPERIMENTAL PROCEDURES Alloys were prepared by arc-melting electrolytic manganese and iodide titanium in a water-cooled copper crucible under a helium atmosphere. Excess manganese was added to each melt in order to allow for losses incurred during melting. The alloys were then wrapped in molybdenum foil and sealed in evacuated quartz tubes for annealing at various temperatures, as shown in Table I, followed by quenching in cold water. Although the inside of the tubes showed evidence for some loss of manganese from the specimen during annealing, there was no evidence of any reaction between the specimen and either the molybdenum foil or the quartz tube at these temperatures. It was later found that the manganese loss was considerably reduced by annealing these alloys in sealed quartz tubes containing one atmosphere of purified argon. As an added precaution the surface of each specimen was ground off before crushing the alloys to -270 mesh powder, using a hardened steel mortar and pestle. X-ray powder patterns were obtained using either FeKa or CrKa radiation in an asymmetrical focusing camera, which gave excellent dispersion of the closely spaced lines. Pictures were also obtained using a Debye camera of 5-cm radius which provided data in the angular region not covered by the focusing camera. The alloy specimens were polished and examined metallographically, using an etchant consisting of 60 pct glycerine, 20 pct nitric acid, and 20 pct hydrofluoric acid. The 10-g buttons were in each case broken in half and found to be well-melted and free of any gross segregation. One half of certain alloy buttons was submitted to chemical analysis in the "as-cast" condition. No appreciable change in composition seemed to occur during annealing . RESULTS The X-ray pattern of alloy Ti1.17Mn0.83 was found to agree well with that of the ternary R phase which was first found in the Mo-Cr-Co system,' and re-

Jan 1, 1962

By M. R. Stauffer, Z. Hajnal

Seismic velocity determinations over Precambrian outcrops near Flin Flon, Manitoba, indicate that several different rock types have sufficient velocity contrast to make reflection mapping possible. Stratigraphic and fault contacts between metasedimentary and metavolcanic rocks have been mapped at some depth. A mu1ti-fold reflection survey attempted to trace the depth extension of an ore-bearing (Pb-Zn) rhyolite horizon within the metavolcanic rocks. A synthetic seismogram has been produced from a 10,000-ft sonic log and provides means of comparing seismic records with the local geology. From this the optimum frequency spectrum and the maximum resolution of the seismic signals were estimated.

Jan 1, 1978

By E. Douglas Sethness

The uranium industry is booming. In Texas alone, there are about 22 different companies with active exploration programs. Twelve solution mines have been permitted; three surface mines have been authorized; and two mills are currently in operation. However, the industry also has a problem, and that is the disposal of radioactive wastes. Over the past several years, stories concerning nuclear wastes have appeared frequently in the news. One of the most frequently cited cases occurred in Grand Junction, Colorado. In 1966, after ten years of investigations, the U. S. Public Health Service (PHS) discovered that tailings from a uranium mill were being used as fill material and aggregate for local construction purposes. It was estimated that between 150,000 and 200,000 tons of material had been removed and used under streets, driveways, swimming pools, and sewer lines. In addition, tailings had been used under concrete slabs and around foundations of occupiable structures. Further studies prompted the Surgeon General to warn that the risk of leukemia and lung cancer could be doubled at the measured radiation levels. More recently, the L. B. Foster Company discovered that its building site in Washington, West Virginia, was radioactive. While digging a foundation, the ground erupted and a ball of fire 30 feet high shot out. Evidently, the dirt was laced with radioactive thorium and zirconium, a potentially explosive mixture contained in a Nigerian sand which had been used by the previous site owners in the manufacture of nuclear fuel rods. Just this month we have read about legal suits to stop exploration for a nuclear waste disposal site in Randall County, Texas. The U. S. Department of Energy is trying to locate a deep underground nuclear waste depository for final burial of over 76 million gallons of high-level wastes. The problem is acute, the wastes are accumulating at a rate of about 300,000 gallons per year. Nor do these numbers include the spent fuel elements from nuclear power plants that are in temporary storage facilities. Fortunately, public awareness of these and other related issues is high. Unfortunately, the differences in the waste products from the nuclear fuel cycle are not always apparent to the general public. There are two distinct types of radioactive wastes: "high-level", which consist of spent fuel or wastes from the reprocessing of spent fuel; and "low-level", which, in general, are by-product wastes. There are numerous non-technical definitions that can be applied to help the layman differentiate between high-level and low-level wastes. For this latter purpose, it is best to think of them in terms of what we can see and feel. In general, high-level wastes are physically hot and can cause acute radiation sickness in a short period of time. Low-level wastes are not hot, but may cause chronic health effects after long exposure. The wastes which we are concerned with in the uranium mining and milling industry are low-level wastes. As recently as ten years ago, there were very few controls or regulations governing tailings disposal methods. At the same time, mine reclamation was not enforced through either state or Federal laws and the long-term viability of abandoned tailings ponds was not assured. The regulatory climate has changed significantly in the last decade, however. The low-level radioactive wastes generated by uranium mining and milling are generally contained in a tailings pond. Approximately 85-97% of the total radioactivity contained in uranium ore is present in the mill waste that goes to such tailings ponds. The isotope Radium-226 is probably the most potentially harmful radioactive parameter in the ponds. Radium emits gamma radiation and is also an alpha particle emitter. Because gamma radiation is very penetrating, it presents a potential health problem when a source is located external to the body. Gamma radiation will go through the body, causing damage to each cell encountered on the way. Although alpha particles have very little penetration capability, they can cause extensive cell damage. For this reason, alpha particles are a problem after inhalation or ingestion. Radium creates a health hazard by both of these mechanisms. Radium decays to radon gas which can be inhaled and serve as an alpha particle emitter. Additionally, radium is very soluble and readily enters the natural hydrologic cycle if allowed to leach from a tailings pond. With a half-life of 1620 years, radium has plenty of time to be taken into the food chain and end up in our bodies, emitting alpha particles. Because the potential health problems are better understood today than ten years ago, and because the Nuclear Regulatory Commission (NRC) has developed increasingly stringent government regulations, the uranium mining industry applies a high level of technology to the disposal of nuclear wastes. In most cases, low-level radioactive wastes are disposed of at or near the site where they are produced. There are six commercial burial grounds for low-level wastes, but it would not be economical to ship all mine or milling wastes to these sites. The on-site disposal methods most often used are ponding

Jan 1, 1979

By G. R. Purdy, J. A. Malcolm

The isothermal dendritic precipitation of y in p CuZnSn is compared with the isothermal formation of Widmanstatten a plates in p CuZn. Although both precipitates are evidently bounded by semicoherent interfaces, the dendritic shape of y evolves through smooth "sinuoidal" shape perturbations, while a-p interfaces tend to be strictly planar, or rnicroscopically faceted. An estimate of the average inter-facial free energy of cube-oriented y in p through the Mullins-Sekerka analysis indicates that it is low (of the order of 50 ergs per sq cm). Interface mication is apparently controlled by volunle dij'usion, and the observed anisotropy in growth probably results from anisotropy of inter facial free energy. Studies of the grain boundary precipitation of y in p indicate that the precipitate can grow in both $ grains, but becomes unstable with respect to the grain with which it shares a mobile semicoherent interface. Facets observed at the tips of Kurdjumov-Sacks-oriented Wid-manstatten a plates correspond to variants of an irrational hahit, near (231)0. Comparison with Hu and Smith's determination of relative interfacial free energies of a-(3 boundaries suggests that this system possesses an extremely deep o cup, which results in an ej'ective low-o zone. The possible effects of such a cup on the stability of a-p interfaces are discussed, a needles, grown during rapid continuous cooling, possess microscopically smooth interfaces, and are characterized by a high degree of' damage in the region of the boundaries. These boundaries, induced to move on tempering at 200"C, become faceted as equilibrium is approached, which seems to indicate that boundary structure and mobility in this system are dependent on the local degvee of departure from equilibrium MULLINS and sekerkal have elucidated the phase boundary stabilizing effect of surface tension. a factor not taken into account in previous treatments of morphological development. Their analysis applies to the isothermal growth of a pure spherical precipitate (planar in the limit of infinite radius) in a slightly supersaturated solution, under conditions of inter-facial local equilibrium and isotropy of interfacial free energy. More recently, several other factors which might tend to stabilize planar interfaces have received attention. These are: i) interface diffusion;4"8 and ii) slow interfacial reaction. cahn7 included a slight anisotropy in interfacial free energy, and showed that it has no stabilizing effect, but forces shape perturbations to reflect the anisotropy. shewmon4 noted that dendritic morphologies are rarely observed in solid-solid systems, and, in particular, postulated that slow interfacial reaction occurs at all boundaries between proeutectoid ferrite and austenite, except those which propagate parallel to {11 l)y planes (for Kurdjumov-Sachs [K-S] related phases). Previously, Aaronson~ had proposed interfacial reaction at the broad faces of Widmanstatten plates, and expected that the lateral motion of high-mobility incoherent ledge edges would produce planar precipitates bounded by law-mobility semi-coherent interfaces. The problem of interfacial reaction during the dif-fusional formation of precipitates has often been ignored, although it is apparent that a small component of chemical reaction must exist at any moving interface." Further, all solutions of the diffusion equations for boundary conditions corresponding to isothermal growth predict infinite growth rate at time zero, so that elements of interfacial reaction would be most easily detected at early times. However, reported deviations from diffusion control are comparatively rare," and the local-equilibrium diffusion-control model appears adequate for the description of many isothermal growth systems.'2"9 Cahn14 has treated the problem of migration of an interface which is able to reach positional energy minima, and concluded that such an interface, if subjected to a high local ther-modynamic "driving force", may migrate normal to itself without the benefit of ledges. As local equi-

Jan 1, 1968

By Clemens Jones

An interesting paper by J. E. Merion and Edward Hart, in Volume I., No. 2, of the Journal of Analytical Chemistry, on the Decomposition of Blast-Furnace Cinder by Acid, describes a plan of sampling the cinder by means of a previously-heated iron bar thrust into the cinder car or into the cinder at the notch, and then allowed to cool, thus chilling the cinder which adheres to the bar, and rendering it decomposable by hydrochloric acid, of 1.12 sp. gr. A short series of results is given, from which the deduction follows that blast-furnace cinder " is decomposed perfectly when chilled." Where many silica determinations are to be made, this method, if reliable, would effect notable economy of time and reagents. The conversion of insoluble silicates by fusion with an alkaline carbonate, together with the subsequent solution, evaporation, drying, etc., is destined to remain the standard method. But all fusionmethods are time-consuming and expensive. Chilling appears to render the supplementary method available for all practical purposes, in the determination of silica in cinder. But, with a view of securing more evidence on the subject, and in view of the fact that uniform results were not obtained by employing this method, it was decided to test the method in the laboratory of the Thomas Iron Company where a large number of silica determinations are made. The experience met with may not be devoid of value, both theoretical and practical. Mr. Iles's paper, in the Chemical News, Volume L., 1881, doubtless suggested to several chemists, connected with iron metallurgical

Jan 1, 1888