Search Documents

By Donald J. Drinkwater, M. C. Fuerstenau

Many important contributions to the more fundamental aspects of mineral processing have been made this past year. Mular1 researched the flotation characteristics of pure zinc oxide and also samples that had been doped with Al+++ and Cu++. Correlation of the response of pure zinc oxide to oleate flotation with a calculated zpc (from solution equilibrium) suggests that adsorption of oleate ion is coulombic in nature. Doping the sample with Al+++ (which will make the ZnO more n-type) had a marked effect on the maximum value of pH at which 50% recovery was obtained at constant collector addition. That is, when 0.5 mole percent Al+++ was added, the pH for 50% recovery was reduced by about four units. Treatment with Cu++ was found to have little effect on the flotation response of zinc oxide, even for additions of one mole percent. Since the zero points of charge of the Al+++ doped powders were not measured, it was not possible to correlate flotation data of these samples directly with charge phenomena.

Jan 2, 1966

By S. Usui, I. Matsuoka, H. Sasaki, J. Shimoiizaka

Depression of galena by sulfite or chromate ion in xanthate flotation was investigated by means of adsorption measurements, electron diffraction and flotation tests. Flotation of galena was depressed by sulfite ion only when galena had been oxidized; no depression took place with unoxidized clean galena. A similar behavior was found when chromate ion was used as a depressant, with the exception that the chromate ion depressed unoxidized clean galena around neutral pH. Depression was attained with galena on which xanthate still remained in appreciable amounts, indicating that the depression is not due to a decrease in xanthate adsorption. The galena surface produced sparingly soluble films under conditions in which depression of galena took place. These films were identified by electron diffraction as lead sulfite and lead chromate on oxidized galena and as chromic oxide on unoxidized clean galena. These observations in conjunction with contact angle measurements, indicate that the depressing action of sulfite or chromate ion arises primarily from film deposition resulting from the reaction between depressants and the galena surface. The thickness of the film was analyzed by means of electrochemical polarization.

Jan 1, 1976

By Andrew A. Blair

It is now well known that certain pig-irons give a considerably smaller percentage of sulphur when determined by evolution-methods than when determined by oxidation-methods. The most striking examplcs of such irons are those made either wholly or in large part from New Jersey magnetites containing more or less titanium. It is never safe to use an evolution-method on such iron; for it is quite common that the sulphur result by evolution is only one-half or even one-third as great as that obtained by oxidation. For this reason, evolution-methods should be discarded, except in the analysis of pig-irons known to contain the sulphur in a state of combination from which it is evolved as sulphuretted hydrogen on treatment with hydrochloric acid. A good example of an iron containing, in the residue, sulphur insoluble in hydrochloric acid having come to our attention, it was determined to try to isolate a suspected insoluble sulphide. A large piece of high-silicon gray-forge iron was accordingly selected as the most promising material to work on. This piece was dissolved slowly, through several months, in dilute hydrochloric acid, aided by the electric current, yielding a soft graphitic residue. The object of dissolving a mass of iron, instead of drillings, was to prevent the crushing, by the drill, of any insoluble crystalline compound that might be present. The first step in the preparation was to break up the graphitic material and put it through bolting-cloth of 157 meshes to the linear inch. This was done by crushing the mass under the fingers on the bolting-cloth fastened over the top of a beaker, while a stream of water from a wash-bottle washed the finer portions through the cloth. The suspended matter was allowed to settle. It was then transferred to a platinum

Jan 1, 1902

By W. H. Corbould

The township of Cloncurry is situated in the northwestern part of Queensland, about latitude S. 20" 42' 53" and longitude E. 140" 30' 25". Townsville is the port through which all the trade passes and is about 470 miles east-northeast of Cloncurry township. The Cloncurry copper district covers an area about 200 miles long by 40 miles wide. Unfortunately the mines are very scattered over this area, there being no large groups of mines. Mount Elliott mine is situated about 70 miles south from the township of Cloncurry, and Mount Oxide mine about 150 miles north of Cloncurry. The district has been known for the last 35 years, and in the early stages a large amount of capital was expended with little to show for it; but within the last four years the railway has been extended from Townsville to Mount Elliott and about 40 miles north of Cloncurry, which has made possible the treatment of the ores of the mines on this extension. The Mount Elliott company within the last few years has smelted and converted on its mine 169,688 tons of ore for 20,554 tons of blister copper, containing 20,377 tons of copper, 35,642 oz. of gold and 28,841 oz. of silver, at a cost of about 233 per ton of blister copper, f.o.b. Townsville. This cost included all development, wages, salaries, general management, office, agency, legal expenses, freight, etc. The gold and silver contents would practically pay for freight to Europe, refining, realization charges, etc. The costs of supplies are as follows: Firewood, 15s., coke, 75s., mine timber, 54s., and coal, 60s. per long ton; explosives: dynamite and gelignite, 50s., and blasting gelatine, 65s. 6d. per case, Mount Elliott Mine The pay shoot of the orebody outcrops at the surface for about 200 ft., and lies between two slate walls about 40 ft. apart., having a general

Jan 1, 1915

By Lewis Smith

CHROMIUM is one of the new metals, but considerable research has been required to determine an approximate record of its production from 1827 until the present. Its use in the form of pure metal is not extensive; of the chromite mined, about one-half is required for making ferrochromium, about two-fifths goes directly into refractories and the remainder is absorbed chiefly by the chemical trades. The industries that demand chromite for such uses are mainly in countries that produce little chromite, while the important chromite-producing countries are not generally consumers. The international flow of chromite is therefore of interest, as yell as the political and commercial control of resources of the metal.

Jan 1, 1931

By D. Swan

Industrial research may be defined as a critical and exhaustive investigation to create new and better ways of doing things. The results of industrial research are new and improved products, processes, and techniques. This broad definition, of course, covers investigation of all subjects by either individuals or groups of people, and this chapter aims to examine the purpose (what research tries to do), and methods (or how research is done) as applied in the mineral industries. Concepts and History The idea or concept of organized research probably originated in the universities of Europe. There, groups of scholars banded together for discussion and application of their particular specialty to a common problem. Publication of the conclusions drawn from such investigations gave scholars in other areas the opportunity to review and criticize the work of their colleagues, and one of the hallmarks of scientific research work is the publication and criticism of the results of the investigation. It was not until the late nineteenth century that the concept of organized research for the profit of industry was recognized. During the late nineteenth and early twentieth centuries, a large number of industrial enterprises sponsored organizations to study the application of the physical sciences with the aim of making discoveries that would result in profit to the sponsoring organization. The tangible benefits accruing from these activities were so great that they, in turn, fostered several other methods for the support of organized research activities. For the large problems involving public interest, United States Government scientific re- search laboratories were set up. As the demand of smaller enterprises for research activities increased, research institutes and consulting laboratories were organized. In Europe the idea of common industry sponsorship of research centers grew and many large research organizations there were sponsored by associations of manufacturers. Finally, in the United States

Jan 1, 1959

By R. S. Dean. J. R. Long, T. R. Graham

Following the development of electrolytic manganese production by the Bureau of Mines, an extensive program was planned to study the character of this high-purity product and its possible utilization in various alloy combinations. Previous work reported in the literature concerning alloys containing substantial amounts of manganese dealt largely with material prepared from relatively impure grades of the metal, and in many instances the impurities thus introduced did not permit true evaluation of manganese as an alloying element. One phase of the Bureau's program included a general review of the system and the establishment of the physical properties of copper-manganese-zinc alloys, using electrolytic manganese, and with particular emphasis directed to compositions within the alpha solid solution area. A number of reports of the work on alloys in this system, giving specific data concerning the equilibrium system and some of its alloys, have already been published. One study' established the alpha solid solution area at various temperature levels and composition ranges up to 50 pct manganese. Other investigation reports presented the properties of selected alloys; namely, a 65 pct copper, I0 pct manganese, 25 pct zinc alloys;1 a sensibly white manganese brass composed of 70 pct copper, 20 pct manganese, 10 pct zinc,3 and a series of alloys with a constant copper content of 60 pct and 5 to 25 pct manganese, balance zinc.4 In these reports tensile properties as influenced by cold-working and subsequent annealing were given in detail. Additional data are now available on other alloys of the alpha region up to 50 pct manganese, and these, together with previously published information, are sufficiently complete to establish the relationship between properties and composition for this portion of the ternary system. The present report is a summary of the tensile properties of wrought alloys in the form of sheet and rod stock. The summary is necessarily limited to data for only one condition of cold-work and a single annealing temperature, since a complete exposition of all the data available would be too extensive for this presentation. Nevertheless, it is possible to make a reasonable approximation of the tensile properties in other conditions of cold-worki"g and annealing by a correlation of the data previously presented on specific alloys and the data given here.

Jan 1, 1947

By S. A. Braley

DRAINAGE water from coal mines is probably the most serious water pollution problem today, varying in importance according to location of the mines and geological structure. Drainage may be either acid or alkaline in character. Acid discharge, the most severely detrimental to a stream, is caused by natural oxidation of the sulfuritic material (FeS2) in the strata associated with the coal seam. Since the acid is the result of a natural reaction the acid water differs because it does not cease with abandonment of the mining operations. There is no known economical method of neutralizing acid mine water or any practical method to prevent oxidation of exposed pyrite. Since production of acid from a mine does not stop when mining stops, the total quantity produced depends entirely upon the excavated areas. The increasing volume of acid water in manv mines has greatly increased operating costs. Pumping is expensive and acid mine waters are destructive of all equipment, especially metals in pumps and piping, and necessitate the use of corrosion-resistant materials. Discharge of the acid mine drainage into streams neutralizes their normal alkalinity, causes them to become acid, and produces an environment unfavorable for aquatic life and unsuited for industrial or domestic use without costly treatment. Mine drainages vary in percentage composition over wide limits, although the usual dissolved substances are ferrous and ferric iron, aluminum, calcium and magnesium sulfates, and lesser amounts of sodium, potassium and manganese sulfates and chlorides. Some alkaline discharges may contain heavy concentrations of iron as iron bicarbonate. These waters may produce iron hydroxide deposits in the receiving stream but do not cause it to become acid. In the extensive literature on acid mine water there appears to be a great deal of confusion about the importance of various components and the methods for their determination. In many instances faulty conclusions have been drawn from use of unsuitable methods of analysis. It is desirable that the factors and terms used in evaluation of analyses of mine waters should be so clearly defined that any interested person could properly appraise any analytical report. Some analysts report complete chemical analyses of mine waters and neglect to record drainage volumes. Others report only a minimum of analytical data after taking no precautions to preserve the original composition of the water during the time elapsing between collection and analysis. Some use methods of analysis intended for so-called pure waters of the potable and boiler water classes. These methods are not applicable to highly buffered waters such as mine water. Probably the most common criteria for evaluation are pH, free acidity, or acidity or alkalinity to methyl orange or methyl red, total acidity or acidity to hot phenol-phthalein, and the sulfate content. If these determinations are made on carelessly collected samples after a few days to weeks standing in warm rooms, they do not in any way represent the character of the water flowing from the mines. It is hoped that a brief discussion of the fundamental value of some of these factors may lead to a bettqr understanding of the need for more careful evaluation of mine water discharges. The term pH is one used by chemists to express relative acidity or alkalinity in terms of concentration of effective hydrogen ion in a solution. It is defined as the negative logarithm of the hydrogen ion concentration or activity in equivalents per liter. pH = logarithm A neutral solution, which is one containing the same number of hydrogen and hydroxyl ions, has a pH of 7. As the hydrogen ions increase and the solution becomes more acid, the pH decreases toward zero; and as the hydroxyl ions increase and the solution becomes more alkaline, the pH approaches 14. When dissolved in water to a dilute solution acids like sulfuric and hydrochloric, commonly known as strong acids, ionize completely, and the pH or hydrogen ion concentration varies with molar concentration of the dissolved acid. However, in high concentrations of such acids, the pH or hydrogen ion concentration is less than the acid concentration because the acid does not completely ionize. In only very dilute solutions does the pH represent the total amount of acid that can be neutralized by an alkali. All ionization reactions are equilibrium reactions. If other chemicals are added to the solution of an acid and the added chemical produces an ion that is the same as one of the ions of the acid, the degree of ionization of the acid is altered and the pH changes to some value that represents the active hydrogen ion of the new solution. Thus if iron sulfate is added to a solution of sulfuric acid the pH increases, since the common sulfate ion suppresses the degree of ionization of the sulfuric acid and decreases the effective hydrogen ion. However, the total acidity of the solution is increased. There are two salts composed of iron and sulfate— ferrous and ferric sulfate. In these salts there is no hydrogen ion that can ionize to give an acid solution, but when they are dissolved in water, the pH is less than 7 and the solution becomes acid. This is caused by a reaction known as hydrolysis and is represented by the equations FeSO4 + 2H2O ? Fe(OH)2 + 2H + SO,: or Fe,(SO,)3 + 6H2O ? 2Fe(OH)3 + 6H+ + 3504 A solution with a total acidity of 5000 ppm according to the first equation will have a pH of 4.40 but one with an acidity of 75 ppm, according to the sec-

Jan 1, 1958

By K. L. Clark, Nicholas Kowall

MAXIMUM furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. WORK OF OTHER INVESTIGATORS In 1938, Burns, Moore and Archer published a curve7 that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the range found in constructional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only 0.20 per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E. 43xx steels. His procedure consisted of chill-casting a test bar that was large enough to give a surface that could be prepared for Brinell indentations. The test piece was quenched immediately after solidification was complete and hardness readings were taken, so that the carbon content could be read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. EXPERIMENTAL WORK Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By Thomas P. Forbath

THE sudden realization that known sulphur reserves amenable to mining by the Frasch hot water process are nearing exhaustion focused attention on widely scattered surface deposits throughout the world. These deposits are not necessarily of lower sulphur content than ores located underneath Louisiana or Texas salt domes which usually average about 30 pct sulphur disseminated in limestone matrix. Their near surface occurrence, however, renders exploitation by the Frasch process impossible. As is well known, the Frasch process depends on the presence of 500 to 1000 ft of overburden and cap rock above the sulphur deposits to permit melting underground sulphur in place by diffusing hot water under pressures of 200 to 600 psig in the formation and raising the molten sulphur to surface by air lift. This process renders possible the production of pure sulphur which is 99.5 pct pure without any subsequent treatment. Surface deposits contain sulphur in the same range of concentrations as the salt dome deposits, i.e., from 10 to 50 pct sulphur, associated with various gangue materials such as silica, limestone, and gypsum. The pirincipal distinction, then, does not lie in the percentage of sulphur contained in the ore, but in the geological nature of the deposit. A recent study' of the world sulphur supply situation estimated 1950 sulphur production in the free world countries at 5.6 million long tons, of which the United States produced 5.2 million tons, or 93 pct of the total. While America's domestic needs alone would have been covered by national production, about 1.4 million tons were exported during the same year. Despite all the steps which are being taken to restrict use of elemental sulphur and to force the fullest possible development of alternate sulphur sources here and abroad, the deficit in elemental sulphur production will probably increase with time. As a result of intensive prospecting for oil throughout the Gulf Coast area discovery of significant new salt domes is held unlikely. With the growing scarcity of sulphur and what appears to be an inevitable rise in price, recovery from deposits not amenable to Frasch-process mining assumes greater economic importance. Untapped Reserves The most important deposits in this category are located in Sicily, where elemental sulphur occurs in Miocene limestone and gypsum formation. Sulphur content of these ores ranges from 12 to 50 pct with an estimated average of 26 pct. Although quantitative estimate of these reserves is not available it is held that they exceed 50 million tons of sulphur. Similar deposits occur also on the mainland which contribute about one-third of Italy's total current annual production of 230,000 tons, but these are known to be nearing exhaustion. Significant surface deposits of volcanic origin are located in South America, Japan and western United States, silica being characteristic gangue con-stituent. The largest of these deposits are in South America. More than 100 extend over a zone 3000 miles long, paralleling the west coast of South America. 'Total sulphur content of these deposits has been estimated to be as high as 100 million tons. The main islands of Japan also possess at least 40 known volcanic sulphur deposits with probable reserves of 25 to 50 million tons.' Prospected reserves in western United States might amount to 2 million long tons, principal deposits being located in the northwestern part of Wyoming, southern Utah, and eastern California. Volcanic deposits of lesser importance are found around the Mediterranean, in Turkey and Greece, and in Africa, Egypt, Abyssinia, and Somaliland. Beneficiation Methods Different methods of beneficiation have been used in these various locations. In Italy the Calcarone kiln and Gill regenerative furnaces are used exclusively. Both utilize heat liberated by burning part of the sulphur in the ore to liquify or vaporize the remaining sulphur, which is recovered by solidification or condensation. The Calcarone kiln is of conical shape, generally 35 ft in diam at base and 18 ft high. A kiln of 25,000 cu ft capacity burns for about two months and yields about 200 tons of sulphur. The Gill furnace consists of a series of chambers with domed roofs. Sulphur is burned and melted in one chamber at a time and the hot combustion gases are used to preheat the ore charge in the subsequent cell. These furnaces operate on a cycle of 4 to 8 days. The recovery yield of both systems is about 65 pct. Sulphur losses amount to 25 pct through the combustion to sulphur dioxide; about 10 pct is retained in discarded calcines. Ores containing less than 20 pct are not considered suitable as furnace feed. These methods are not only wasteful because of the low recovery obtained, but represent a serious atmospheric pollution problem. Sulphur produced ranges from 96 to 99 pct purity and thus does not match Texas or Louisiana sulphur. Owing to the present shortage, sulphur in the Middle East sells

Jan 1, 1954

By E. C. Pechin

The attention of the members of the Institute of Mining Engineers is asked to a description of the minerals of Southwestern Pennsylvania, as representing the minerals of an enormous area, stretching continuotisly, with local variations, along the western slopes, and at the base of the Alleghany Mountains, through Western Pennsylvania, West Virginia, and Kentucky, and destined to play no mean part in the future of the iron trade of the country. The particular locality is at and near Donbar, in Fayette County, where the most careful examinations and extensive developments have been made. The deep gorges cut by the Youghiogheny and Monongahela Rivers, in their passage through the mountains and lower lands, give admirable facilities for observing the measures lying between the sandstones of No. 11 and the upper coal measures. Apart from its varied mineral and agricultural resources this section of country has great historic interest attaching to it. It was down the Monongahela that Braddock led his ill-fated army to its defeat under the wails of Port Duquesne, and it was up the Youghiogheny River and Dunbar Creek that the shattered remnants hastily fled to gain the camp of Colonel Dunbar, the second in command, who was entrenched upon a high knob, at the head of the creek which bears his name, and which is still known and visited as Dunbar's Camp. Numerous streams, runs, and localities preserve the names of the guides and pioneers who accompanied, in early colonial times, young George Washington, who was pushing his surveys into the trackless and hostile wilderness, and many of them taking up large tracts of

By E. A. Nesbitt

THE important permanent-magnet alloys 15 years ago contained carbon and depended upon it for their permanent- magnet properties. In recent years great, advances have been made in a number of new alloys substantially free of carbon. These include Remalloy,l an alloy of iron, cobalt, and molybdenum, the various iron- nickel-aluminum alloys of the Mishima2 type, and the more recent Alnico V3 in which the best properties are developed by heat-treating in a magnetic field. The Mishima and the Alnico types of alloys are very brittle and after casting must be ground to size. This article describes a permanent-magnet material4 that can be machined as cast, and when handled with some care can be .rolled to thin sheet and drawn to fine wire. Optimum magnetic properties are developed by a simple heat- treatment, and at this time the ductility A of the alloy disappears. If the cast alloy is heat-treated without cold-working the magnetic energy product is about 1.0 X 106. This material is called Vicalloy I (pronounced vicalloy, V for vanadium, I for iron, and C for cobalt). When the alloy is first hot-worked and then considerably reduced in area by cold-swaging, drawing or grooved rolling, it is found that after heat-treatment the magnetic energy product measured in the direction of previous extension can be increased to 2.0 to 3.5 X l06. These higher values have been obtained only after reductions in area of 75 to 95 per cent, and since the material hardens considerably during working, the reduction ordinarily can be accomplished only in fine wires, although larger sizes can be reduced by the use of powerful machinery. When the material has been cold- worked in such a manner as to improve its energy product substantially, it is called Vicalloy II. Commercial use of Vicalloy has been made in the recording of speech. Tape 0.002 by 0.050 in. has been found superior in quality to all others tried, and is now used in the Western Electric Mirrorphone In a variety of forms Vicalloy I or II is useful in many laboratory instruments, and in experiments in which the sizes and shapes required cannot be obtained with the other more brittle permanent-magnet materials. In 1936, during a study of other age- hardening magnetic systems, it occurred to the author that some of the iron-cobalt-vanadium alloys might be suitable for permanent magnets. The proportions of iron, cobalt, and vanadium were varied and a range of alloys of particular interest was found, as shown by the indicated area in Fig. I. The limits of this range of com- position are 30 to 52 per cent iron, 36 to 62 per cent cobalt, and 4 to 16 per cent vanadium. The compositions indicated by points outside this area were also tested. PREPARATION AND PROPERTIES OF VICALLY I The alloys were usually cast in graphite molds into bars ¾ in. in diameter and

Jan 1, 1946

By Dale C. Matthews, Donald L. Simpson

Hecla Mining Company's Lakeshore Mine and Metallurgical complex near Casa Grande, Arizona, is the first plant in North America to utilize the roast/leach/electrowinning process for production of cathode copper from sulfide concentrates. Oxide copper ores are also mined at Lakeshore. Using sulfuric acid and sponge iron by-products of the roast/leach operation, the oxide ore is leached in vats, the copper is precipitated with iron and recovered as cement copper. This paper will describe the roast/leach facilities and discuss the operating conditions at which more than 95 percent of the copper in concentrate is made soluble in acid solutions while less than 5 percent of the iron is rendered soluble. More than 97 percent of the sulfur contained in concentrate is captured either as strong sulfuric acid or as soluble sulfates in leach liquors. The iron rich residue after leaching is pelletized and reduced to sponge iron in an SLRN reduction kiln.

Jan 1, 1981

By A. Soundraraj, S. Singh, R. C. Deshpande

THE detonation of a high-explosive charge having a metal-lined conical cavity (shaped charge) results in a fast-moving jet and a slow-moving slug.1-4 Clark and Bruckner reported the metallographic studies of a cast-iron slug. The present note describes the metallographic studies of a copper slug and discusses the principle of flow involved. The shaped charge consisted of a 5-cm diam cylinder of cast high explosive (60-40 RDX-TNT mixture) having a 45 deg and 0.16-cm thick copper cone. The copper (99.5 pct purity) had a grain size of 0.06 to 0.08 mm diam and a hardness of 65 to 75 Hv. These were fired into a deep container of water and the slugs were recovered undamaged. The longitudinal and transverse sections of the slug were polished, etched, and examined for mi-crostructural changes. Macroexamination revealed a radial grain flow inwards towards the center and a downward component of flow towards the base of the slug. Fig. 1 shows schematically the micro-structural changes observed on the longitudinal section of the slug. The region D near the apex and also along the outer surface of the slug was characterized by the presence of heavily deformed and twinned grains. Some of the grains were having bent or crossed twins, Fig. 2. The grain size in this region was of the same order as that of the

Jan 1, 1960

By C. P. Melloy

INTRODUCTION Ventilation practice at Isa Mine has been evolving since underground mining began in 1931. Much fundamental work has been conducted and reported regarding the primary ventilation system [Mathews K.E. et a1 (1967) and Brown J.R., Fisher T.H., Gibson K.L. (1979) 1. However, ventilation networks for subsystems such as open stopes, have evolved with experience. This paper outlines current ventilation practice for open stoping. Mount Isa Mine The mine is located in semi-arid North-West Queensland, Australia, and currently produces 20 000 tonnes of copper ore and 10 000 tonnes of silver-lead-zinc ore daily in each five day working week. Mining extends over a north-south strike length of 3.5 km with a maximum width across dip approaching 1 km, and is to a depth of 960 m (Figure 1). At present approximately 90% of the mine's copper production is from the 1100 Orebody, which contains ore reserves of 121 million tonnes of 3.2% copper. Open stoping is currently the mining method employed, and is used for primary stoping and pillar recovery adjacent to cement fill walls. The development of stoping methods in the 1100 Orebody has been documented by Kirkby R.W., Blair J.R., and Hutton R.C. (19781, Hornsby B. and Sullivan B.J. (1978), and Alexander E.G. and Fabjanczyk M.W (1981). As many as thirteen open stopes may be producing concurrently in the Orebody (Figure 2). The multiple silver-lead-zinc orebodies containing reserves of 54 million tonnes of 150 g/t silver, 6.4% lead and 6.5% zinc, are mined by open stoping, and cut and fill techniques. These methods have been documented by Goddard I.A. and Bridges M.C. (1977 1, and Goddard I. A. (1981 1. Only the ventilation of the 1100 Orebody open stopes will be discussed. However, the same ventilation philosophy is employed in open stope design in the lead orebodies.

Jan 1, 1981

By S. Jess Larsen

Modern technology has provided the world with many innovations to improve living standards, ease of job performance, efficiency, and managerial control. While not expected to compete with the computer revolution, Kerr-McGee Coal Corporation has found a way using laser technology to solve one of their haulage problems. Operating successful and profitable surface coal mine facilities in Wyoming's Powder River Basin require economies of scale, flexibility of operation, conscientious cost control, and ever-present innovative effort. Because haulage costs are the major source of expenditure in surface mining, Kerr-McGee recognized early the need for maximum haulage productivity and the economies of scale provided by large haulage trucks. Special conditions that exist in the Powder River Basin coal fields require consideration. The coal thickness (up to 100 feet and more) and varying depths of overburden dictate that a haulage unit with good gradability characteristics be used to avoid undesirable long ramps. Two and often three coal seams are encountered by most mines, which necessitates operating from several coal and parting faces simultaneously. This situation consumes much space, and to minimize the scope of problems, a coal haulage unit with good maneuverability and stability is needed. Finally, the low density of coal (±1500 pounds/loose cubic yard) demands a large volume capacity to utilize truck load carrying capability effectively. These conditions prompted Kerr-McGee to select unitized two-axle bottom dump trucks of the 160-170 ton size for primary coal haulage at its two Gillette-area mines. Use of 170-ton bottom dump trucks at the Clovis Point Mine handles most of the coal haulage, but the truck

Jan 1, 1983

By Joseph P. Hodgson

Since about 70 per cent. of the total cost of mining is due to underground work which is out of sight, it is essential that expenditures should be made here to the best advantage. A great many mistakes have been made which were expensive, but perhaps these have not even been detected by mine owners. In the future these may be minimized to some extent, especially if there is cooperative effort on the part of each employee. I have been interested in this subject for some years and have tried to deduce principles and methods. These have proved highly advantageous and may also be of help to others. Some corporations, like the United States Steel, and the Cleveland-Cliffs Iron Co., have done a great deal in this field by having stated meetings of their organizations, with the view to interchanging ideas among their men and educating them along the lines of concerted effort. Since no man knows all about the various branches of mining, it is advisable that frequent meetings of the operating department be held for the interchange of ideas and that all members of the organization have an opportunity to express themselves on the various subjects. It has often been found that in discussions between heads of departments, foremen and bosses, many valuable suggestions may be obtained which promote the best interests of the company. The method regarded as the most conducive to cooperative effort, and pursued by the organization, is to analyze and develop the different phases of various mining subjects at regular meetings. Nine Foremen's Dinners In the latter half of 1912, the Copper Queen Consolidated Mining Go. gave monthly dinners to the men in the operating departments. Those who attended were superintendents, foremen, shift bosses, engineers, geologists, and heads of all departments, making a total of about 75 men. After the dinner, lectures were given on subjects which pre-

Jan 1, 1917

By R. W. Smith, C. Schroeder, R. Haddenham

Amphoteric surfactants are heteropolar organic compounds which possess at least two functional (ionic) oppositely charged groups per molecule. The ones studied are manufactured by General Mills and possess one or more long hydrocarbon chains plus a carboxyl group (s) and an amino or imino group. Hallimond tube and M. C. Fuerstenau micro flotation cell flotation tests were performed on quartz and hematite as a function of pH using amphoteric, cationic, and anionic surfactants as collectors. For the most part, flotation could be correlated with an interaction of charged groups on the collectors with oppositely charged sites on the minerals plus association of hydrocarbon chains. The comparison of flotation in a Hallimond tube and an M.C. Fuerstenau cell shows that one should use care in using the latter if one excludes an additional frother from the system. Also, it is interesting to note that sometimes greater collector concentrations are required in the Fuerstenau cell for comparable flotation recoveries.

Jan 1, 1974

By R. M. Douthwaite, G. Birkbeck

The effect of grain size and specimen dimensions on the occurrence and magnitude of a yield point drop in pure iron has been examined. The tests were done at room temperature. The results indicate that gain size is the critical factor determining whether a yield drop occurs. The specimen diameter:gain size ratio does not influence the magnitude of the yield drop for the range of gain size and specimen diameters investigated. HUTCHINSON,' petchY2 and worthington3 have investigated the grain size dependence of the upper yield stress (uUYP) and the yield point drop, ouyp - aLYP, in Armco iron, mild steel, and Si-Fe, respectively. These authors used center-annealed wires to avoid stress concentration from specimen shoulders and to ensure uniformity of the applied stress. Coarsegrained specimens show no yield point drop; the yield point drop then increases as d-'I2 increases (where d is the grain diameter). These results can be understood in terms of Petch's analysis2 in which the magnitude of amp depends on the strain rate in the (limited) number of grains deforming plastically at the upper yield point. If N grains per unit volume are undergoing plastic deformation, the strain rate in the deforming grains is l/Nd3 times higher at the upper yield stress than when the whole specimen deforms homogeneously. If N is constant and independent of grain size at uUyp, then all the grains are deforming when ~d~ = 1, so there is no yield point drop. At finer grain sizes, the yield point drop is given by: where AU, is the friction stress increase corresponding to a tenfold strain rate increase. Christ, Smith, and Burton studied the upper yield point in 0.050-in.-diam wire specimens prepared from zone-refined iron. Each end of the 2; -in. specimens was soldered to a & -in. diam steel ball and the load applied through the two balls. There was a yield point drop in specimens with grain diameters less than 0.1 mm; no drop was observed in specimens of grain diameter greater than 0.1 mm that were free from veining substructure, but specimens of grain diameter 0.129 mm, annealed in the y range, showed an upper yield point. and this was associated with the presence of a veining substructure in these specimens. Christ et al. suggested the upper yield point occurs when more than a specific number of grains fill the specimen cross section so a multiplicity of slip is required to initiate plastic deformation. Table I summarizes the published data on the grain size at which the yield drop disappears. On the basis of this data the ratio of specimen diameter:grain diameter = 5 to 27 appears to be the critical value for the occurrence of a yield point drop. Thus, petch2 interprets the appearance and magnitude of the yield point drop in terms of the limited number of grains deforming plastically at uuyp, whereas Christ et a1. consider that the occurrence of the yield drop depends on the ratio specimen diame-ter:grain diameter. The published data cover a wide variety of materials so some variation between the results is to be expected, but the size range covered in the data of Table I is rather limited. In an attempt to discover whether the specimen diameter:grain size ratio or the grain diameter is critical in determining

Jan 1, 1969

By S. C. Dhara

A process of solvent extraction and separation of platinum group metals (PGM) and gold using primary, secondary, tertiary, and quarternary organic amines has been briefly described. The effects of amine structures; the use of diluents; the principle of synergism and antisynergism in the mixed extractants; the oxidation states of metal ions are explained in the amine extraction process of precious metals.

Jan 1, 1984