Search Documents

By C. D. Woodward

The Anaconda Copper Mining Co. purchases 25,000 kw. of electric power for its mining operations at Butte, Mont. This power is delivered, over duplicate feeders, in the form of 60-cycle, 2400-volt, three-phase current, to five compressor plants, where most of the energy is used for driving air compressors. At the compressor plants are located the switching apparatus for controlling the 2400-volt power and distributing it to the various mines. At these points, also, there are a number of motor-generator sets for converting the alternating current to 275-volt direct current for the haulage systems. Pole lines convey the powcr from the compressor plants to outdoor transformer substations at most of the mines. When it is not economical to distribute the power at the lower voltages in the mines, transformers and motor-generator sets are placed at strategic points underground. All power is purchased on a maximum-demand basis; therefore there is installed at one of the compressor plants an eight-element totalizing graphic wattmeter. This instrument records simultaneously the value of all power taken at the numerous points of delivery, which not only climinates the diversity factor but permits load dispatching between compressor and pumping plants, and thus materially reduces the maximum demand from the power system. As most of the mine hoisting is done by 90-lb. compressed-air winding engines, the air-compressor equipment for the winding engines and mining operations is quite extensive. The standard air compressor has a rating of 7500 cu. ft. per min. of free air, and most of the compressors are directly connected to synchronous motors. The synchronous motors are designed for 80 per cent. loading power factor, thus facilitating power-factor correction of total mine load. Consequently by cooperation with the power company, the voltage of the power received at the compressor plants is constant. In the mines there are installed an induction motor load of approxi-mately 10,000 hp., and 4500 kv.-a,, in transformer capacity. It is the practice to install 2200-volt motors in the mincs, except those rated below 50 hp, hence there are in operation underground about 5000 hp., in the

Jan 1, 1923

By Ulick R. Evans, Maurice Cook

The structural changes in metals brought about by annealing follow-ing a deformation at a low temperature has been the subject of many investigations. No less than eleven metals and alloys have been studied in some detail; namely, aluminum, tungsten,2 iron,3 copperI4 gold, zinc,6 cadmium, tin: lead: brass,1° and cupronickel. As a result, it is possible to frame a qualitative statement of the effect of the degree of deformation and the temperature of annealing on the structure finally attained.

Jan 1, 1925

By J. D. Embury, R. M. Fisher, A. S. Keh

An investigation of the defect structure and properties following large strain deformation has been carried out using transmission electron microscopy and mechanical testing for a range of ferrous materials and for copper. It is shown that, for a variety of ferrous materials, a cellular substructure is developed during the initial stages of working and on further deformation the dimensions of this substructure are reduced. Quantitative measurements of the flow stress and the scale of the substructure indicate that the strength of heavily worked materials is largely determined by the spacing of cell walls. These cell walls act as dislocation barriers in a manner analogous to grain boundaries. FCC materials do not harden as extensively as bcc after cold working and the present observations on copper indicate that the dimensions of the substructure in fcc materials are not markedly reduced on deformation. The differences between the fcc and bcc structures produced by large plastic strains are ascribed to differences in the extent of dynamic recovery. It is tentatively proposed that the greater stability of substructural barriers in bcc structures results from strong interstitial Pinning effects. It is proposed that for large plastic strains the work-hardening process may be considered in terms of the reduction of substructural-barrier spacing during the working process. This pvovides a simplified hut useful analysis of the strain hardening occurring during mechanical processes. THE mechanisms of strain-hardening processes have occupied the attention of numerous investigators over the past three decades and a multitude of theories have emerged in this field. The majority of previous work has been concerned with the development of a description of the plastic behavior of single crystals in terms of dislocation theory.'" In contrast, scant attention has been given to the strengthening mechanisms operative during mechanical working processes such as rolling and drawing. The large plastic strains involved in these processes make it difficult to correlate the observations with any elementary dislocation theory. Further, as Bullen and coworkers3 have opined, for large plastic strains both hardening and recovery occur simultaneously and thus it is extremely difficult to estimate the effect of plastic strain on the ambient internal stress field. It is probable that for large plas- tic strains any theoretical estimate of the internal stress field must be made in terms of complex dislocation groups. Although some valuable theoretical work has been done toward calculating the elastic properties of dislocation groups4 any detailed self-consistent model for large plastic strain is as yet impossible. With these limitations in view it is still of value to examine the mechanical properties of highly strained materials as a function of their substructure. This relationship is explored in the present communication for a variety of materials subjected to rolling, drawing, or swaging. The primary object of this investigation has been to establish the validity and the limitations of the substructural strengthening mechanism proposed by Embury and eisher' for drawn pearlitic wire and by Meieran and Thomas for drawn tungsten wire. No attempt has been made to delineate the basic interaction mechanism which occurs between a slip dislocation and the substructure and the authors believe that a great deal more experimental evidence must be compiled before these fundamental aspects can be explored. Also, no specific attention has been given to the detailed formation of substructure during working. Experimental Details. A variety of materials were used in this investigation, the compositions and heat treatment of which are tabulated in Table I. The commercially pure iron is referred to throughout this report as Ferrovac E. The mechanical working processes were all performed at room temperature. The wire drawing was performed on a manual drawing bench. Reductions of between 10 and 20 pct in area per pass were used in both swaging and drawing. The experimental parameter used to evaluate the mechanical properties of the materials was the 0.2 pct proof stress. This was determined for wire samples using an Instron tensile machine at a crosshead speed of 0.02 in. per min. The techniques for preparation of samples for transmission electron microscopy have been described previo~sl~.~ Specimens from wire samples were prepared from longitudinal sections and in some cases from transverse sections. To evaluate the substructural characteristics of rolled materials, thin foil samples were prepared of both the face and edge sections. Results. One of the more familiar ways of expressing work hardening in mechanical working is by the flow stress as a function of reduction in cross-sectional area. Fig. 1 shows such a plot for Ferrovac E eutectoid carbon steel and for copper. The curve for Ferrovac E is characterized by an initial stage of rapid work hardening and a final stage of rapid work hardening separated by an intermediate stage with a low rate of work hardening. This behavior is typical of many ferrous materials and the drawn pearlite wire previously investigated by Embury and Fisher is a more pronounced example. Copper shows an initial

Jan 1, 1967

By T. Egleston

The necessity of using a refractory material capable of much greater resistance to chemical action and having a far higher melting-point than those which contain silica, which melt and sweat off in the furnace even when not exposed to bases forming with silica more or less fusible compounds, has led to a careful practical study of all those materials which contain very refractory bases. The results of these researches, extending over several years, and made on a very large scale in many of the largest works in Europe, are of the highest interest, not only considered as a step in the progress of the study of the materials themselves, but in the application of refractory materials to metallurgical uses in general. The result of the experience of the last seven years with these basic materials, as in general with all such substanccs, is that natural products cannot be used as such. They are either too uncertain in their quality, contain substances which may in certain cases be very injurious, or, when in a condition in which they might be used, are so rare as to become practically unavailable for employment on a large scale. The materials that may he used are therefore not only limited in number. but they must be prepared artificially. When the use of basic artificial material is further extended, no doubt the number of these substances will not only be greatly increased, but the methods of preparation will be both perfected and cheapened to such an extent as to permit their application in processes for which they have hitherto proved too expensive. The quantity of refractory materials required for making ingots will he from 130 to 150 Ibs. per ton, or between 6 and 8 per cent. of the metal produced. In an establishment producing 2000 to 3000 tons of steel per week, considerable space is required to handle the basic materials properly. It is proposed in this paper to briefly discuss these basic materials and their application in the only two metallurgical processes where they have as yet been applied. These are the basic Bessemer and the basic open-hearth process, known as the Thomas-Gilchrist processes.

Jan 1, 1886

By Raphael Titi-Manyaka, I. Iwasaki

Chlorination and chloridization behaviors of pyrite, pyrrhotite, chalcocite, covellite, chalcopyrite, bornite, heazlewoodite, millerite, and pentlandite in chlorine, gaseous ferric and sulfur chlorides were investigated by thermogravimetric analysis. The reaction mechanisms are discussed in terms of theoretical weight changes, thermodynamic calculations, and X-ray analyses of reaction products. The experimental findings are in direct application to the development of a scheme for producing nonferrous metal chlorides, elemental sulfur, and ferric oxide from complex sulfide flotation concentrates.

Jan 1, 1977

By F. Keller, A. H. Geisler

Although the subject of precipitation from solid solution appears to be one of the more profitable fields in metallurgy for study with the electron Microscope, few comprehensive studies have yet been made. Occasionally electron micrographs have been published that illustrated alleged precipitation in various alloys, but frequently the apparent size, shape and distribution of the particles do not fully agree with those expected from theory or from observations of the Precipitate when the particles have grown to a size resolvable with the light microscope. The presence of a Widmanstatten pattern for submicroscopic precipitate particles has been demonstrated for only a few aged a1loys.l The initial problem has been the development of suitable techniques for applying the transmission-type instrument to a field that has been inherently associated with reflection-type microscopes. The various techniques have been the subjects of numerous publications, and instead of describing them individually here it will sufficc to say that the oxide film method has proved to be the most satisfactory method yet found for studying the microstructure of aluminum alloys with the electron microscope. This method has the definite characteristic advantage that the actual surface layer of the specimen is examined and not a plastic or silica replica. Doubtless suitable methods for forming and removing the oxide film could be developed for alloys of other metals. The purpose of this report is to point out the characteristics of the oxide film method that have been observed during the studies of numerous aged aluminum alloys and to present the results of these studies. Preparation OF Specimens The oxide film method for preparing specimens of aluminum alloys for examination in the electron microscope has been described in detail previously,¹,² Briefly, the procedure consists of preparing the metallographic specimen, forming the film by anodic oxidation and removing the film from the prepared surface of the oxidized specimen, The specimen is polished accordillg to the usual procedure for microscopic examination.³ he specimen may then be etched to remove flowed metal but etching to attack the alloy constituents or to leave them in relief as in the replica processes is not necessary. Electrolytic polishing is not generally recommended, Deep-etched specimens are used frequently, however, since they provide information that is not revealed by polished specimens and frequently present the same information more clearly than do the polished specimens, The surface preparation of specimens to be deep-etched is not important, since specimens that have been subjected to the first wet PoliShing operation are generally used, but frequently the as-rolled surface is Suitable. These specimens are then etched using a suitable macroetching reagent.

Jan 1, 1947

[ ]

Jan 1, 1938

Bill S.1431 for the creation of a Department of Natural Resources has received a propitious hearing before the Senate Committee on Government Operations. Interior Secretary Rogers C. B. Morton was one of the prominent witnesses who testified in favor. The department had been proposed, Morton said, with "the conviction that the development of all natural resources would be harmonized with the most practicable possible means to protect and preserve the environment, consistent with the social and economic needs of the Nation." Another opinion on the pro side came from Atomic Energy Commissioner Clarence E. Larson, who said that a "total picture" had become essential to the establishment of a policy for developing energy resources in the best public interest. Commissioner James T. Ramey, on the other hand, was one of the AEC dissenters. Ramey said he believed the reorganization of resource responsibilities would hinder efforts to deal with energy-environmental problems and prevent the use of AEC "expertise and facilities" to the greatest advantage. As Arnold Weber, associated director of the Office of Management and Budget, pointed out, however, retiring AEC Chairman Glenn T. Seaborg is in favor of the new department. Another supporter, and one who can cast a vote on the bill, is Sen. Frank E. Moss. Final Standards for emissions from new stationary sources will be published by the Environmental Protection Agency on October 27. The initial proposals, appearing in the Federal Register on August 17, called for limiting emissions per million Btu of heat input (maximum 2-hr average) to 0.2 lb of particulate matter, and, where solid fuel is burned, to 1.2 lb of sulfur dioxide and 0.7 lb of nitrogen dioxide. While the new rules are mainly for new plants, the EPA is also proposing them for "existing plants which are modified in such a way as to increase or alter. . . their emissions."

Jan 1, 1971

A. G. Cockbain—The paper by Burlingame, Bitsianes and Joseph is of great interest in extending the work done on high grade sinters, particularly that of Hessle, and the development and application to them of the technique of McBriar, Johnson, Andrews and Davies on ironstone sinters. In this laboratory the work of McBriar et al. has also been continued and extended to cover high grade sinters, and a sectioning technique similar to that used by McBriar et al. was attempted on sinter cakes made in the laboratory sinter unit, using magnetite concentrates (containing 64 pct Fe). In these experiments no attempt was made to flush out the products of combustion with nitrogen before cooling. It was considered that free air penetration would occur on only a limited scale with the size of sinter cake made (14 in. sq x 12 in. deep). Chemical analyses of the zones showed generally similar features of those described by Burlingame et al. and especially the FeO rich region at and just behind the flame front, i.e. zones of ignition and combustion. This seems to indicate that the nitrogen atmosphere does not materially affect the states of oxidation in the sinter cake or at least that special care is not required unless the sinter cake is small. Burlingame et al. consider that FeO present has some significant part to play in the mechanism of sintering. This view does not find favor with the author. The reduction of iron oxides in the presence of red hot coke is a well known phenomenon, whether conducted in an atmosphere of nitrogen or in a crucible in air, and in view of the presence of some carbon in the hot sinter, especially just at the ignition zone, cessation of the progress of the flame front will in no way affect the reduction of iron oxides near hot coke. Even in a nitrogen atmosphere some CO and CO, will be generated by reduction and by continual oxidation and reduction of CO as the transfer agent, the oxidation state of the iron oxides can be lowered quite rupidly so long as free carbon exists with enough heat. Knowing the composition of the gas at the flame front (obtainable by probes), it would be possible to calculate the static oxidation state of Fe2O3/Fe3O2 in equilibrium with it and hence obtain a check on the chemical analyses to see if in fact direct reduction of the Fe2O3/Fe2O1 to FeO has taken place. Have the authors attempted this? It appears to this writer that what is required is some means of reducing rapidly the heat content of the ignition zone and immediately behind, and at the same time insuring no oxidation by the air. In ironstone sinters the difficulty of oxidation state of the iron did not arise on account of the very large slag bulk. However, in high grade sinters knowledge of this, and also the mechanism whereby high oxidation states can be obtained in the final sinter, is of great interest. R. D. Burlingame (author's reply)—The question has been raised as to whether the high FeO content found in high-fuel sinters is due to actual reduction at the advancing flame front or due to unavoidable direct reduction during the quenching period. For such direct reduction to have taken place in the freshly-formed sinter, a considerable amount of solid carbon would have had to escape combustion and be available throughout the hot sinter zone during the quenching period. A simple stoichiometric calculation with the limited data available indicates that a zone of freshly-formed sinter over 2 in. wide must have averaged roughly 2 pct C to accomplish the amount of reduction found. Furthermore, the presence of this amount of carbon would indicate that the fuel in the charge had not burned over a narrow front but over a zone at least 2 in. thick. In contrast to such a condition, the data of the present investigation indicate that the combustion of fuel is confined mainly to a narrow front in which high temperatures and reducing conditions favor. the formation of excess ferrous iron.

Jan 1, 1959

Jan 1, 1985

By Richard F. Hinds, F. O. Reudelhuber

Application of the conventional depletion drive calculation methods to volatile oil reservoirs results in erroneous estimates of ultimate recovery. In view of the increasing number and importance of volatile oil reservoirs, a special technique has been developed which will result in more realistic predictions using laboratory data obtained from reservoir fluid studies of a specific type. The experimental data are designed to permit continuous material accounting and, therefrom, provide the hy-clrocarbon composition of both the flowing oil and gas phases. The resultant well-stream composition data are then used directly in surface recovery calculations utilizing equilibrium ratios. A step by step procedure, specifically designed for routine use by the practicing reservoir engineer, is presented in an appendix. An actual study performed on a deep Mid-Continent reservoir is used ay an il-lustrathe example. INTRODUCTION It has been a practice for many years to utilize the conventional ma- terial balance methods in conjunction with relative permeability concepts for the prediction of recovery from solution gas drive reservoirs.' Those who have performed such calculations recognize that compromises of several types are necessary in order to reduce the calculations to a reasonable degree of complexity. The most serious assumption involved results from the necessity of treating the produced oil and gas as separate fluids, independent of each other in their behavior. It is further assumed that the gas which is evolved in the reservoir as a result of pressure decline will not yield liquid upon the reduction of pressure and temperature resulting from production through surface equipment. Although these shortcomings have been recognized,' it has been difficult to attempt refinement of calculation procedures since the laboratory data available normally were not of the proper type or extent to permit such calculations. Three general procedures have been available for depletion drive calculations when laboratory fluid data are of the conventional type. Differential Procedure The most simple, and most widely used, method requires use of the formation volume factor and gas sol- ubility data obtained from a differential liberation performed at reservoir temperature. This procedure ignores the differences existing between the fluid behavior in the reservoir and its behavior as it is produced through surface separation equipment. The errors introduced are not serious when dealing with very low volatility fluids and this method may be utilized if the laboratory data indicate only slight differences between the differential data and the flash data obtained from separator tests. Modified Differential Procedure This method was developed when it became apparent that medium volatility fluids evidenced a wide difference between the flash and differential data. The differential data are adjusted by changing from a residual oil basis to a stock tank oil basis. All that is required is multiplication of the differential data by the ratio of residual oil to stock tank oil relative volumes existing for the original reservoir fluid at the determined saturation pressure. This procedure generally results in increased calculated ul-timate recovery; however, such results should be viewed critically. Upon examination it may become apparent that the results are influenced by errors in reservoir liquid

Jan 1, 1958

By Robert Linton

THE PURCHASE of silver by the United States Government under the provisions of the Pittman Act is practically completed. Producers of silver in this country will now have to market their silver in competition with the rest of the world. It therefore becomes of interest to study such data as are available and endeavor to obtain such suggestions as may be afforded therefrom as to the probable future market position of the metal. Conditions influencing the marketing of silver are numerous and complex. It is a commodity entering. into the arts and manufactures, and therefore influenced by the condition of various lines of business which make use of it; it is currency-being used by all countries for subsidiary coins and even as the founda-tion of the system by a very few; and it serves as a frequent basis for speculation. The various factors involved can easily set up so many cross-currents in the flow of the metal that predictions in regard to the market position of silver can never be safely made, although it may be possible to form some idea of prob-able trends over a sufficiently long period. Of course price is determined, as is the case with all commodities, by the inexorable workings of the law of supply and demand.

Jan 6, 1923

By George Stone

THE stack gases from regenerative furnaces are very seldom utilized for the production of steam. If the temperature of the gases is not higher than 300° C. (572° F.) there is no economy in their use for this purpose, as the amount of available heat is very small and the temperature is so little above that of the steam that the interchange is too slow. With higher temperatures of the waste gases, however, good results can be obtained. At the plant of the New Jersey Zinc Co. (of Pa.) at Palmerton there are a number of return tubular boilers, each 6 ft. in diameter and 20 ft. long, with 96 3.5-in. tubes, which are heated by the waste gases from the spelter furnaces. These furnaces have continuous regenerators heating the air only and the stack gases reach the boilers at a temperature of about 450°. The gas producers for one of these furnaces require 14 tons of anthracite (a mixture of Nos. 2 and 3 buckwheat), and the waste heat from the furnace gives a little more than 42 h.p. in steam. The boilers are not well adapted for the purpose, as they are much too large for the amount of heat going to them and the area of the tubes is not sufficient to take the gas from two furnaces without causing an objectionable amount of back pressure. The plant was built without any idea of using waste-heat boilers, and it was impossible to place the latter as close to the furnaces as they should be. Furnace and boiler are connected by an underground brick flue in which the temperature of the gas drops about 100°, losing 40 per cent. of its available heat. If the .boilers were close to the furnaces the horse power of each would be 70 instead of 42. Even under these unfavorable conditions the boilers have been very advantageous, as one boiler easily supplies the steam necessary for two batteries of producers. With such low gas temperatures the heating surface of the boilers is, of course, not as efficient and the flue areas need to be considerably larger than for coal firing.

Jan 10, 1913

By Hans Lundberg

FOR the last 20 years, geophysical methods have been in practical use. The results accumulated during this time have been broad enough to enable us to formulate some general rules for conducting geophysical surveys to the best advantage. It is a well established fact that electrical and magnetic methods have aided the geologist to outline bodies of ore, to differentiate between various types of rocks hidden from view and also to determine the thick-ness of the layer of drift that covers the bedrock. Fundamental require-ments for a successful solution of a geophysical problem is the existence of physical differences between the various formations under investiga-tion. If such conditions exist, our problem becomes a physical, mathe-matical and geological analysis of the effects of these differences upon the structure of an arbitrarily produced, or already existing, field of force. Experience has shown that reliable and consistent results in analyzing such fields of force are obtained only if: (1) the methods and apparatus used are scientifically sound and designed to provide information with a maximum amount of accuracy, reliability, sensitivity, simplicity and speed of operation, and (2) the interpretation of the results of such an investigation is guided not only by rigid mathematical rules but also by common sense, based upon sound geological knowledge and imagination. Today, a number of methods are based upon sound principles, are highly sensitive and are well suited for field work. The instrumental developments have resulted in self-contained instruments, which permit the determination of field ratios and intensities with great accuracy. Magnetic surveys have almost become standardized. The electrical methods, mostly based on the determination of potential-drop ratios, or electromagnetic field ratios, are built as bridge circuits and it is easy to determine amplitude, as well as phase relationship of the various electrical and electromagnetic fields.

Jan 1, 1938

By C. E. Jackson, E. C. Nelson, A. L. Christenson

Much information regarding the transfornlatio~lal characteristics of a steel as it cools in a known manner from the austenitic state can be obtained from dilatometric studies. This method has received more arid more attention because of its great flexibility, accuracy, and ease of interpretation. 'The method is entirely applicable to any rate of heating and cooling although the experumental procrdures for high rates of cooling have offered some difficulties. This paper presents a description of equipment employing cooling rates up to 500 °C. per secorld and the results of dilatometric observations on six commercial steels are included. French and Klopsch1 studied the cooling transformations of a serirs OF carbon steel, using the thermal arrest method. This was followed by the systematic investigatiol1 of Esser and co-workers on the effect of carhon2 and other alloying additions. in which the transforlnation temperature\ were determined by magnetic induction measurements indicated by a string galranoineter. Emphasis was placed on determining Ar' trailsformations and the critical cooling rates for these steels. The maglietic measurements wrere used in an effort to obtain more accurate data at higher cooling rates. Measurements of thermal arrest were made also to check the validity of the magnetic indications, and good correlation was found between the two, although Esser's,Ar' temperature measurements on iron-carbon alloys were about 200°F. lower than the measurements made by Fresnch and Klopsch. A notable contril~ution by Esser was the introduction gas quenching. wever and Rose4 used a moving-coil galranometcr in the study of the .Ar and Ar" of iron-carbon alloys by the thermal arrest method and obtained somewhat lover Ar" temperatures than those observed by Esser below I per cent carbon and considerably higher ahove. They concluded that the cooling rate had little influcncc on the Ar" temperatures above 0.4 per cent carbon, although Esser had observed a decrease in the -4r" temperature with increasing cooling rate with similar steels. Digges determined the .Ar" temperature4 for a scries of high-purity iron-carbon alloys, and close agreement with his results was obtained by Greninger. The thermal arrest method. together with metallographic observation used in both these studies, represents the latest investigations of this type. Any investigation by thermal analyses is dependent on the heat of reaction and the specific heat of the

Jan 1, 1945

By C. R. Austin

In a recent paper1 the authors presented information on a refinement of the Rohn type of creep test with data on pure iron that exemplified the behavior of the apparatus. The present paper extends that work to nickel and cobalt and to the examination of the comparative high-temperature properties of two widely used commercial alloys. Careful attention has been given to the effect of plastic deformation in decreasing creep rate, using the elementary metals iron, nickel and cobalt for purposes of analysis. In any endeavor to develop new materials for high-temperature service one soon encounters a real problem as to the sort of test to be employed in evaluating the commercial possibilities of the alloys. At one time it was considered satisfactory to determine the tensile strengths at elevated temperatures and to use these values as a criterion for the commercial application of the alloys. More recently the proportional limit has been used as a means of classification. Data obtained from a form of bend test have also shown promise as providing a "merit index" of high-temperature serviceability.= Koerber and Pomp3 state that since the influence of testing time is small, the high-temperature yield point of steel furnishes sufficiently reliable and concordant values up to about 350" C. (and a maximum of 450" C. for alloy steels) to serve as a suitable basis for comparison evaluations of materials and for judging permissible stresses. Koerber and Pomp consider, however, that above these temperatures creep limit must be substituted for the high-temperature yield point as the all-important characteristic of the material. Whatever may be their definition of

Jan 1, 1934

By L. Douglass Anderson

Fox some years past the annual reviews of the metallurgy of lead have almost uniformly stated that there have been no great changes, such as there were, being more particularly noticeable in the refinement of details. While this is quite true, nevertheless these changes in details are gradually bringing about a condition that, taken as a whole, constitutes a considerable advance in the art. Local circumstances have often -compelled metallurgists to adopt certain peculiarities of practice which -upon trial have been found advantageously applicable to more than the restricted district of origin. This paper will deal with some of the more novel features developed in recent years at the United States smelter, Midvale, Utah, particularly with reference to the influence of the bag house. The plant is equipped with six blast furnaces, 48 by 160 in., mechanically fed; four Wedge furnaces for roasting matte and sulphide ores; four Dwight-Lloyd sintering machines; 20 converter boxes for blast roasting; storage bins for ore, fuel, and fluxes; "oxide" and "sulphide" sampling mills; bag house taking all the gases of the plant; arsenic plant for treating the dust gathered there; laboratory, shops, etc. The most marked feature of the plant is its complete bag-house system. Of the many schemes thus far tried for preventing damage to surrounding agricultural interests the writer is aware of none as yet quite as efficient as the bag house. A common remark of visitors upon approaching the plant and viewing the clear stacks is that it appears to be shut down, whereas once inside all the evidences of industry are found.

Jan 7, 1914

By H. H. Stoek

Danville, the county seat of Montour county, Pa., was one of the earliest and best-known centers of the iron intlustry in the State. It is situated on the north bank of the north branch of the Sosquehanna river, twelve miles east of the confluence of the north and west branches of that river at Northurnberlttnd. The ore-belt, extending for a distance of twelve miles along the north bank, has been developed in a number of places, but nowhere so extensively as in the immediate vicinity of Danville. Hence, a description of the mines in that locality will suffice, as typical of the workings of the entire section. Geology. The Montour ridge consists of an anticlinal fold extending from the source of Wapwollopen creek on the east to the west branch of the Susquehanna, which it reaches at the mouth of Chilisquaque creek. According to the reports of the First Geological Survey of Pennsylvania, the length of the ridge is nearly twenty-seven miles, with an average breadth of three-fourths of a mile, and a maximum elevation of six hundred feet in the vicinity of Danville, where it also attains its greatest width. Just north of Danville the Mahoning creek cuts through it, exposing the iron-ore on the hill-side, where advantage has been taken of this to work the beds on the southern slope of the ridge by means of drifts. The sections given in Fig. 1 are taken from the reports of the First Geological Survey of Pennsylvania, made in 1858, by H. D Rogers, whose description of the Moatour ridge was so complete and accurate that the entire report was reprinted as an appendix to Vol. G 7 of the Second Geological Survey. The approximate crosssection shows that near Danville the top of the ridge is of Clinton vol, xx.—24

Jan 1, 1892

By Robert D. Pehlke, Robert G. Blossey

The solubility of nitrogen in liquid iron alloys containing chromium and nickel has been measured in the temperature range 1550° to 1700°C at nitrogen pressures to 1 ah. The solubility surface has been determined for the iron corner of the liquid metallic ternary to 21 pct Cr and 11 pct Ni. The nitrogen solubility increases markedly with increasing chromium concentration. The effect of nickel and the bilinear effect of chromium and nickel are less pronounced. The solubility data are presented, and interaction coefficients are determined from them. THE solubility of nitrogen has been determined in liquid Fe-Cr-Ni binary and ternary alloys. The work in this laboratory has been directed toward a relatively limited composition range, that is to 20 pct Cr and 10 pct Ni. Humbert and Elliott1 studied the entire ternary; but their investigation was, understandably, limited in this region. The region considered here is of the greatest commercial interest. Knowledge of the solubility in these alloys is important for accurate control of the nitrogen levels in various stainless alloys. Also, the solution behavior is of theoretical interest because of its deviations from ideal dilute solution rules at moderate chromium levels. The nitrogen solubility in the iron binaries has been reviewed extensively by Pehlke and Elliott,2 particularly with respect to the dilute solution interaction parameters. More recently, there has been some interest in accurate descriptions of solute interactions in non-dilute solutions. Most of the investigators have adopted a power series fit to accommodate any non-linearity of the data. The Taylor series expansion is adopted here, using Scimar's notation3 for the interaction coefficients. An alternate method, instead of requiring higher-order expansions, is to restrict the range of the composition variables. A planar solubility surface may be fitted to the data and its range of validity determined. If the axes of this region are displaced from the usual origin—the solvent pure iron—a change in standard state is required for the solution reaction. The standard state for nitrogen in iron is commonly taken as the hypothetical 1 wt pct solution of nitrogen in pure iron. However, for an alloy of appreciable solute concentration, e.g., 13 pct Cr or 18 pct Cr-8 pct Ni, it would be convenient to use that base composition as the solvent and redefine the solution reaction in terms of that particular solvent. A brief derivation follows, defining the free energy of solution in an alloy solvent. Following the treatment by Darken and Gurry,4 for a nitrogen pressure of 1 atm: N (pure component) = N (1 wt pct in solvent) [l] AG=RT ln100/ wt pct N in solvent Taking this reaction for an alloy solvent less the same reaction for a pure iron solvent the relation between nitrogen in pure iron and an alloy is: N (1 wt pct in Fe) = N (1 wt pct in alloy) [2] AG = RT[ln(wt pct N in Fe) - ln(wt pct N in alloy)] Adding ½ N2(g) to each side and subtracting N (1 wt pct in Fe) = ½N2(g), the total free energy for solution of nitrogen in an alloy, referred to nitrogen at infinite dilution, is given by: ½N2 (g) = N (wt pct in alloy) L3] AG°3 = -RT ln(wt pct N in alloy )PN =1 atm Interaction parameters have their usual meaning when ?G°/RT is differentiated with respect to the proper composition coordinate. If desired, the dilute alloy treatment may be utilized with the new reference composition as the solvent. This has. indeed, been done by Small and pehlke5 in their analysis of nitrogen solution in liquid 18-8 alloys. The Sieverts' technique was used for this investigation on an apparatus previously described.6 The materials used in this program were: Ferrovac-E iron, 99.95 pct, Crucible Steel Co.: chromium, 99.95 pct, Union Carbide Metals Co.; nickel, 99.9 pct, International Nickel Co. Recrystallized alumina crucibles were used with no evidence of crucible-melt reaction. RESULTS The locations of the ternary compositions investigated are shown in Fig. 1. The data of Turnock7 and small8 have been alluded to in other papers.5'6 There were no departures from Sieverts' law observed for

Jan 1, 1969

By Charles Austin

IN an earlier series of studies on 18-8 stainless steel at 600°, 700°, and 800°C.1 one pretreatment was used throughout; viz., 15 min. in hydrogen at 950°C., followed by an air quench. Several manufacturers of this alloy since have expressed doubt as to the suitability of the temperature employed, recommending instead the more customary Strauss treatment as promising superior results. In this subsequent investigation on the effects of the temperature of pretreatment several interesting points have arisen, which are described in this paper. Previous work on our equipment had shown a marked difference between alloys of "similar chemical composition" that had been manu-factured by different companies. Accordingly, one mill-bar length was selected from which to prepare all specimens. It could then be assumed that any marked differences in creep characteristics would be due to effects resulting from variations in the pretreatment of the alloy. The material was furnished by the Allegheny-Ludlum Steel Co. in the form of 5/16-in, dia. rod, finished by air cooling from a mill anneal at 1950°F. (1066°C.). It was analyzed only for the elements shown: carbon, 0,07 per cent; chromium, 18.73; nickel, 9.46; manganese, 0.40. Three pretreating temperatures were chosen, the specimens being held for 15 min. in hydrogen at either: (1) 1150°C., to conform to the recom-mended Strauss treatment; (2) 950°C., to compare with the results of previous tests; or (3) 750°C., to initiate precipitation of carbides in the material before testing. As the test cross sections were only 1/8 -in. dia., air cooling followed the annealing treatment. These treatments per-mitted two direct comparisons: (1) between the 1150° and 950°C. treat-ments to indicate the effect of grain size when all carbides were probably in solution at the start of the test; and (2) between the 950° and 750°C. treatments to indicate the effect of carbide "nucleation" for similar grain sizes.

Jan 1, 1940