Search Documents

By R. S. Cartwright

Two types of automatic drilling controls, the Halliburton and the Hild, are now available and are coming into more or less general use in deep drilling. The primary function of both is to maintain a safe limit of torque on the drill pipe, this being accomplished by automatically controlling the weight or pressure on the cutting tool. Neither type will necessarily increase drilling speed, but by permitting advantage to be taken of "breaks" in the hole higher average cutting speed may be maintained. The control is essentially a safety device, and should be considered as such. It is not the purpose of this paper to discuss the merits of drilling controls, although the advantages over manual feed at the brake drum are obvious, but rather to point out some of the limitations. The Halliburton Control The Halliburton control is designed to operate during drilling through the agency of the draw works. Automatic and constant control. of the torque on the bit is governed by clutches on the control itself, and the line shaft to drum shaft drives on the draw works. In operations other than drilling the control is simply a jackshaft between prime mover and draw works. It is, of course, adaptable to any type of power. Because control of the torque on the bit is dependent upon the various ratios or clutch combinations available on the Halliburton control and the draw works, it follows that there are certain limitations in points of control. Table 1 shows the possible ratios which can be obtained with the control and a popular type of three-speed draw works, it being assumed that the highest possible gear combination-the combination which when engaged will suspend the least amount of weight-has a value of 1.00.

Jan 1, 1928

By O. W. Rees, Gilbert H. Cady

Unit coal calorific values represent a close approach to pure coal values; they possess characteristics theoretically inherent in the latter values. They are essentially uniform in the same seam for areas possessing essentially uniform geological environment. They are higher in older than in younger coals in most cases, and in deeper than in shallower coals. In general, they display characteristics closely in accordance with expectation assuming that they are essentially indices of rank. Because it possesses these characteristics, the unit coal value is essentially a standard value, characteristic of each bed in each local region. Hence it can be used as a basis for determining the accuracy of results in newly established laboratories, or when new equipment is installed, or in checking the results of different laboratories, or even in determining the character of coal as mined or prepared if ash, moisture and sulfur values are known. DISCUSSION (A. C. Callen presiding) R. P. Hunson,§ Wayland, Ky. (written discussion).—One of the interesting observatioris made by the authors is that there is a more or less definite correlation between unit coal calorific values and the geological environment of the coal bed. It is very interesting to note that, in general, the unit B.t.u. value increases with the increase in the probable original depth of burial, and that each seam tends to increase in calorific value toward the areas of diastrophic instability. It is generally conceded that Parr's formula, for determining unit coal values, is about as accurate as any formula subsequently proposed for the same purpose. In his formula, Professor Parr did not differentiate between the sulfur present as iron pyrites and that present as organic sulfur. However, the practical application of the formula has shown that this is of little consequence. I agree with the authors that unit coal calorific values are useful ill determining the accuracy of calorimetric determinations, and in determining the character of the

Jan 1, 1934

For four years your Committee has been engaged in the study of problems connected with the educational preparation of professional geophysicists. The Present report represents the conclusions drawn from the investigations and deliberations undertaken since it was first organized. These studies have shown that the evolution of geophysics has proceeded along lines that differed from those marking the advance of classical geology. The latter science developed as a descriptive one, dealing with directly observable terrestrial phenomena, and the elementary, rational explanations that could be offered therefor. The fact that these phenomena were also chemical and physical in nature was seldom given more than passing acknowledgment. During the last half century, however, a new approach to problems of terrestrial phenomena has become of greater significance. This new attack has come through the sciences of physics and chemistry, as the people trained therein have investigated the facts of the earth as problems in their respective sciences. This development has been chiefly at the hands of European investigators, and European universities have long recognized it by establishing departments or institutions of geophysics. In the universities of North America, their arbitrary departmentalization into fields of physics, chemistry, astronomy, geology, etc., has prevented the academic recognition of such domains of science as geophysics and geochemistry. In consequence, the development of these subjects in the United States has been largely at the hands of nonacademic institutions, while the universities themselves are evidently in a state of confusion as to how the subject should be handled. In some places an attempt to teach geophysics is made in the physics department, in others in the geology department, in some in the engineering school, and occasionally as a cooperative effort; a Department of Geophysics is seldom found in North America. In some instances, proper academic plan. ning has been precluded by interdepart. mental jealousies, or by lack of appreciation of the significance of the subject. For the background upon which these conclusions are based, the reader is referred to reports previously issued or SPonsored by Your Committee. The "First Report of the A.I.M.E. Mineral Industry Education Division's Committee of Geophysics Education, 1939," summarizes the replies received to question-

Jan 1, 1946

By Lap-yan Chan

Chan and Goodman (1983) presented a procedure for simulating joint traces and identifying key blocks on an excavation. This paper defines six measures of support requirements that characterize the number and dimensions of key blocks, taking into account the frictional properties of joints and actions of support systems. When correlated with case histories, these measures of support requirements can help in choosing an optimal design for shallow excavations in discontinuous hard rocks.

Jan 1, 1984

Jan 1, 1930

By Joseph H. Taylor

The Ducktown district is in the extreme southeastern corner of Tennessee, its principal railroad point being Copperhill, on the Blue Ridge division of the Louisville & Nashville Railroad, midway between Knoxville, Tenn., and Atlanta, Ga. The ore deposits were discovered about 1849 and development work was begun in the early fifties. Only the "black copper" ores, products of secondary enrichment, from beneath the gossan outcrops and overlying the massive sulphide deposits, were then mined and smelted for their copper content. Upon their exhaustion, attention was directed to the treatment of the pyritic ore remaining, resulting in the devising of a process consisting of open-heap roasting, followed by blast-furnace smelting, which was practised until 1903, when semi-pyritic smelting was adopted. In 1908, the companies operating in the district, on account of litigation brought about by alleged smoke damage to forests and vegetation in the adjoining counties of Georgia, were compelled to erect enormous acid plants to prevent the escape of the sulphur dioxide produced in the smelting operations. The utilization of this sulphur dioxide in the manufacture of sulphuric acid as a byproduct has added to the revenues of the companies, and at the same time has furnished a valuable source of supply of sulphuric acid to the fertilizer trade of the South, and more recently to the manufacturers of eyplosives for use in the production of war munitions. The steadily increasing demand for sulphuric acid for the manufacture of fertilizers and explosives, together with the decreasing imports of pyrites, from which the acid is generally produced, now makes it imperative that greatly extended resources of pyrite be developed. While the Ducktown deposits do not predominate in pyrite, they do contain an inexhaustible supply of pyrrhotite, admixed with pyrite, which can be satisfactorily employed to supplement or substitute for pyrite in acid making.

Jan 1, 1918

By H. Reginald Hardy, Y. S. Kim

Recent studies of inelastic behavior and acoustic emission in geologic materials further validate the concept that such materials may be considered to consist of an elastic media containing an array of pores and cracks. In the present paper this concept is investigated further by experiments in which the mechanical behavior of a number of geologic materials were studied in detail at low stress levels using ultrasonic pulse methods. Experiments were carried out on cylindrical test specimens of Indiana Limestone, Tennessee Sand- stone and Barre Granite under relatively low confining pressures (0-5000 psi). Analysis of data from these experiments indicated that there existed a low-level critical stress at which there appeared to be a transition in the mechanical behavior of the material. Under triaxial stress, results indicated that the differential critical stress was relatively independent of confining pressure, i.e., the mechanism responsible for the transition in mechanical behavior was governed by a maximum shear stress criteria.

Jan 1, 1971

By T. A. O’Hara

SINCE May 1948, when tungsten carbide bits were introduced at the Flin Flon mine, they have been popular with the miners because of their fast drilling speed and low gage loss. The high cost of commercial carbide bits and tipped drill steel, however, prevented their use except for the hardest rock. In an effort to extend the use of tungsten carbide on a basis economically competitive with detachable steel bits, experimental work was begun in 1950 to test the feasibility of making tungsten carbide tipped drill steel in the mine drill steel shop. This work showed that tipped drill steel could be made locally at less than half the cost of the commercial product. The performance of the local tipped drill steel was comparable to that obtained with commercial carbide bits and tipped drill steel and the cost per foot drilled was much lower.

Jan 3, 1954

By J. E. Warren, J. H. Hartsock

In the receipt of J. E. Warren and J. H. Hartsock's comments on our paper, "Aspects of Gas Deliverability", We wish to point out that all the physical characteristics we conceived as constant were absorbed in the gas deliverability constant of the individual well's performance, listed

By W. R. Hibbard

Pole figures, torque curves, and coercive force have been determined for the following rolled and annealed permanent magnet alloys: Cunife, Cunico, Silmanal, Vicalloy I, Vicalloy II, and Heusler's Alloy. IN the general category of precipitation-type permanent magnet alloys there is a group of ductile alloys, including Cunife, Cunico, Silmanal, Heusler's Alloy and Vicalloy, which can be extensively rolled and annealed to develop a preferred orientation in the crystals of the matrix material. The rolling and annealing textures of Cunifel and Vicalloy' have been previously investigated qualitatively, but no pole figures are available in the literature. In addition, the role of precipitation in these permanent magnet alloys is still somewhat controversial. It

Jan 1, 1957

By W. H. Bassett

THE modern smelting and refining of copper is distinctly an American development. The present demand for sound and perfect castings for rolling is due to the development of American industry. Prac-tically every article made from sheet metal or, for that matter, from any form of metal is made by mass produc-tion methods. Faulty material disturbs the orderly sequence of operations and in addition requires expen-sive inspection and unbearable rejection of finished product. This demand, therefore, is positive and will have to be met. Some mines produce ore that can be smelted and re-fined without the electrolytic process into satisfactory copper for the wrought metal industry, and some of these ores carry small amounts of impurities that are of use in hardening and toughening the copper. Most of the copper ore mined contains impurities that must be removed and, fortunately, precious metals which are separated at the same time make this re-moval profitable. The modern electrolytic refineries have their methods so well under control that the product meets all re-quirements without question if properly fire refined and cast. The "if" in this case is important, because there is evidence of carelessness or want of control at times in the material from some of the producers. It is nec-essary that the melted cathodes should be saturated with oxide to dispose of sulfur and that the copper should then be poled to the proper pitch or set. Sometimes statements leak out to the effect that it is unnecessary to oxidize completely the molten cathodes and a little less rabbling saves poles, which are expensive. The re-sult is that the rolling mill gets porous castings and produces seamy or slivered sheets or strips. The condition of the molds, their temperature, and the temperature of the metal are all important to good copper cakes, wedges, or wire bars. Cracked, and burned molds leave rough places and porous spots. Molds which are out of shape, or cracked, make shrink-age cracks which gap open when the castings are hot-rolled. Dampness means porosity. Drops of oil mean porous or honey-combed areas. Poor or irregular dress-ing means mold wash in the castings. Cold copper or slow pouring means cold sets.

Jan 4, 1928

By C. A. Hartnagel

The production of petroleum in New York in 1940, totaling 4,999,000 bbl., was only slightly under the amount produced in each of the previous three years. The year 1940 started auspiciously with a posted price on Jan. I of $2.75 a barrel. Four price reductions, beginning in May, resulted in August in a low of $1.85 a barrel, after which two increases brought the year's closing price to $2.15 a barrel. The favorable crude price at the beginning of the year stimulated an increased drilling program, especially in the water-flooding districts. In the Allegany County region, which accounts for about two-thirds of the state's oil production, 886 wells, including water-intake wells, were drilled; 200 more than in the preceding Year. During the closing months of the Year there was a marked decline in the number of wells drilled. The unfavorable position in which the industry found itself before midsummer was due largely to the loss of export markets for its high-grade lubricants, constituting approximately 25 per cent of its business. As a result of this situation, runs to refineries were curtailed as much as 30 Per cent at the middle of the Year. Improvement in market conditions toward the end of the Year found the stocks of available crude at an almost record low. Deep DRILLING with the gradual exhaustion of some of the important natural and flood-oil-produc-ing areas of the Allegany and Bradford pools, overproduction will not be a serious problem in the future. The possibility of finding new territory or deeper producing sands has been further lessened by the drilling of additional deep wells for gas in and about the present oil fields. Many of these wells drilled to the Oriskany sand-stone were over 4000 ft. deep and have tested the entire thickness of the Devonian formation, the upper 2000 ft. of which contain all the important oil-producing strata in the state. Water-flooding It is thus evident that the problem of the New york oil producers is not one of find-ing new supplies but of obtaining as much 6 oil as possible from the old developed fields that during the 60 years of their life have 1 produced I 3o,ooo,ooo bbl. of oil. Although a few floods were in operation before I9I9, when the production of oil by flooding was 1 made legal, the output for that year amounted to only 85I,000 bbl. From 1919 I on there has been an almost constant increase, which during the past four years has averaged well above 5,000,000 bbl. annually. During the last 22 years, which constitutes the period of important flooding operations, 651337,000 bbl. of oil have been produced in the state. Careful estimates indicate that between one-third and one-half of the oil fields are being flooded or are already watered out. Some of the flooded and watered-out areas include territory with unusually thick sands, which were highly productive during the early history of the fields. From a recent study of operations in the New York oil fields, it is estimated that about 65,ooo,oo bbl. of oil

Jan 1, 1941

By Frank T. Weems

The basic operating properties of the DorrClone are discussed and certain metallurgical applications which exploit these properties are presented. An effective method of controlling the consistency of the DorrClone underflow is described. THIS paper presents in a general manner some of the applications of the DorrClone (Dutch States Mines cyclone) in the metallurgical and heavy chemical fields. Technical or mathematical analyses of the design factors and of the mechanism whereby the cyclone effects its separation have been capably treated in a series of previous papers.'-' Engineering and operational aspects of a few installations and laboratory tests have been chosen to emphasize the unique classification characteristics of the DorrClone and to illustrate its utility in certain difficult situations. Its use in coal washing and heavy-media operations are not considered. Some 25 or more industrial installations and applications of the DorrClone in the metallurgical fields are operating at present, ranging from single trial units to complete batteries composed of a multiplicity of units. The data were obtained in part from some of these, and in part from operations of units at the Westport Mill, the laboratories and testing plant of the Dorr Co. at Westport, Conn. The DorrClone was developed, in principle, by the research dept. of the State Mines, Limburg, Holland, during World War 11. Its first use was to dewater a —50 micron sand used as a dense medium in coal washing. The metallurgical wet cyclone was first publicized by Driessen and Yancey and Geer.6 ince then the cyclone has been studied as a means of de-watering, heavy media concentration, and fine size classification. The DorrClone is shown in Figs. 1 and 2. pulp to be treated is pumped through the feed nozzle, A, into the feed cylinder, B. The feed nozzle is of rectangular cross-section, the outermost edge being tangent to the feed cylinder walls. Feed shims, C, may be attached to the innermost walls to adjust the open area of the feed nozzle available to entering pulp. The tangential injection of feed under pressure supports the vortex action of the pulp that has been detained in the cyclone; the centrifugal forces of this vortex throw the coarse particles to the walls of the cone, D, where they collect and pass downward and out through the adjustable apex opening, E. The fine particles contained in most of the water that entered with the feed pulp move to the inner spiral of the vortex and flow out through the vortex finder, F, contained in the orifice plate, G, which forms the top of cyclone chamber. The overflow pulp may then spray freely into a spray chamber, H, surmounting the cyclone or pass directly into a 90' elbow, I, of somewhat larger diameter than the vortex finder. Installation Where more than one cyclone is to be installed, best overall efficiency and ease of control are obtained with equal distribution of both pulp volume and weight of solids among the cyclones, and with the same pressure being maintained at each cyclone feed nozzle. Fig. 3 is a suggested arrangement for feeding two or more cyclones in parallel. Feed pressure control: Under normal operating conditions it is not unusual for some surge to exist in the feed that is to be sent to the cyclone. As will be discussed later, surges in the solids content of the pulp are usually not of great operational consequence, but surges in feed volume are a problem. Several systems have been devised for absorbing surges in feed volume, each involving a surge tank. If the surges are small and fairly rhythmical, a tank of sufficient size might be installed to dampen out

Jan 1, 1952

By W. D. Robertson, A. S. Tetelman

The technique of decorating dislocations was employed to investigate deformation and fracture resulting from Precipitation of hydrogen in Fe-3 pet Si single crystals. It is shown that cracks are produced on (100) planes inside crystals, as a consequence of the precipitation of hydrogen gas, either when crystals are quenched from a hydrogen atmosphere at elevated temperatures or cathodically charged with hydrogen at room temperature. Plastic deformation in the vicinity of cracks, observed as arrays of decorated dislocations, is in conformity with the calculated stress distribution about a crack containing an internal pressure, and the observations provide information permitting a detailed analysis of the mechanics of crack growth. The fracture characteristics of crystals containing internal cracks were evaluated at 25o and -196°C and the results are related to the mechanism of hydrogen embrittlement in terms of the growth of preexisting cracks. HYDROGEN in bee iron or steel produces two characteristic changes in mechanical properties: I), a decrease in ductility (macroscopic strain at fracture) that depends on temperature and strain rate, and 2), spontaneous fracture under static load that depends on time and apparent stress. Resolution of these phenomena into the microscopic processes that combine to produce the macroscopic effects is especially difficult in the Fe-H system in which the active component cannot be directly observed and only maintained in equilibrium with great difficulty in the temperature and pressure range in which embrittlement phenomena appear. As a result of these complications, verification of the numerous hypotheses'-5 that have been proposed to explain the microscopic mechanism of embrittlement depends on self-consistency with measured changes in macroscopic properties that are averaged over the volume of a specimen. It is obviously important to obtain a more direct evaluation of the microscopic processes that combine to produce embrittlement. Accordingly, the present investigation was designed to identify and observe, as directly as possible, the microscopic effects of introducting hydrogen into a bee crystal. It was concluded from a previous investigation6 of X-ray line broadening, produced by introducing hydrogen into pure iron at room temperature, that the only effect that could be associated with the introduction of hydrogen was plastic deformation; in particular, dilation of the lattice was not observed, within ± 0.01 pet, and no evidence was found that could be interpreted to support the idea7'* that hydrogen occupies tetrahedral interstitial sites in the iron lattice. The absence of lattice dilation is consistent with the extremely small solubility of hydrogen in bee iron9,10 (0.015 at. pet at 900oC and 1 atm pressure), and the evidence of plastic deformation is consistent with the fact that hydrogen, introduced by cathodic charging, eliminates the carbon yield point.11-13 Following this investigation, the immediate problem was to devise a method by which plastic deformation could be observed directly. The technique employed by Hibbard and Dunn14 to observe the movement of dislocations during bending and subsequent polygonization of Fe-3 pet Si single crystals was adopted and modified for the present purpose to include the observation of dislocation arrays in the volume of the crystal, and their association with the fracture process. EXPERIMENTAL PROCEDURE Single crystals of a high purity Fe-3 pet Si alloy, containing 0.007 pet C, were grown in vacuum by

Jan 1, 1962

By R. A. Burmeister, P. E. Greene

Two methods for the synthesis and growth of single crystals of B6 P are described: a solution-growth process employing nickel as the solvent, and a vapor-growth process employing BBr3 and pH3 as the reac-tants. Relevant portions of the Ni-B-P phase diagram have been examined and liquidus data are presented for an isobaric section at an equivalent P2 pressure of 3.8 Torr, and an isothertnal section at 1300°C. Solution-growth techniques are described and the purity and crystalline perfection of the resulting material is discussed. Epitaxial growth of BeP on &P substrates has been obtained using the vapor-phase system. Evidence is presented which supports the assignment of the stoichioknetry B6P to boron sub-plwsphide. THE B-P system differs from other III-V systems in that it contains two distinct compounds. The existence of the monophosphide (BP) has been known for some time,' whereas the subphosphide (B6P) was reported only recently.' Both of these compounds are large bandgap semiconductors (Eg = 2.0 ev for BP~ and 3.3 ev for B6P4), and are therefore of interest for optoelectronic applications. The crystal structure of B6P is quite different from those of most semiconductors, being derived from that of a-rhombohedral boron by the incorporation of the two phosphorus atoms in the intericosahedral sites of the a-boron unit cell?76 B6P also exhibits a number of unusual characteristics, including a high degree of chemical inertness, hardness, and high-temperature stability. No information concerning other physical properties is available in the literature. The present study is part of a broader investigation of the preparation and properties of B6P. This paper considers methods of growing single crystals of B6P of suitable size and quality for physical-property measurements. A detailed discussion of the electrical and optical properties of B6P will be given elsewhere.' GENERAL CONSIDERATIONS The method first used to synthesize B6P was the disproportionation of BP' according to the reaction The equilibrium P2 pressures corresponding to this reaction were also determined .'" It is therefore possible, in principle, to apply several of the reactions reported for the synthesis of BP to the synthesis of B6P merely by selecting lower phosphorus pressures or higher temperatures, in accordance with the equilibrium data. Other techniques for the direct synthesis of microcry stalline B8P have also been reported.1°

Jan 1, 1968

By Fred Witt, Milton Schwartz

ESTABLISHED methods for obtaining quantitative pole figures for flat sheets1"5 can be extended to apply to thin films on a substrate. The mode of scanning the sample is exactly the same as described in the references? but consideration is given to the fact that the scattered X-ray intensities are due to both the thin film and its substrate with appropriate attenuation factors. The purpose of this paper is to describe a method to obtain the scattered intensities from the film alone for subsequent pole-figure determinations. Fig. 1 shows the four possible general positions of the film (f) and its substrate (s) with respect to the incident X-ray beam (I,). In this paper it will be assumed that the plane of the sample is normal to the plane of the diffractometer. In the diagrams the line jV is the normal to the flat sample and the line P is the trace of the diffracting crystallographic planes in the plane of the diffractometer. The angle of tilt, a, is the positive acute angle measured from the line N to the line P; if this angle is measured clockwise then a is said to be in the positive a region; if this angle is measured counterclockwise then a is said to be in the negative a region. For the reflection cases, the total scattered intensity, at the proper Bragg angle for a particular set of planes, is due to that scattered by the film Vf) and that scattered by the substrate. The beam incident on

Jan 1, 1967

By F. J. Fayers, S. A. Hovanessian

The one-dimensional displacement equation for a homogeneous porous medium, including the effects of gravity and capillaty forces, has been solved by a numerical method. A finite-difference scheme is developed for obtaining saturation, pressure and fractional flow profiles in waterflood recovety problems. From the numerical examples given, it is concluded that the gravitational forces have a pronounced effect on the saturation profiles and the pressure distribution curves of the system. INTRODUCTION Within the past 20 years, a number of papers have appeared in the literature dealing with the quantitative treatment of waterflood recovery problems. In their celebrated paper, Buckley and Leverett1 described a method for calculating saturation profiles when the effects of capillary pressure and gravity are excluded. Terwilliger, et al,2 included the effect of gravity in their theoretical and experimental investigation of oil recovery problems and obtained close correlation between experiment and theory. welge3 described a simplified method for obtaining the average saturation and the oil recovery from an oil reservoir. The effect of gravity can be included in this calculation. More recently (1958) Douglas, et al,4 presented a method for calculating saturation profiles which includes the effect of capillary pressure. The authors start with the one-dimensional displacement equation (which is nonlinear in the derivative) and, by a change of variable, transform this equation to a semi-linear partial differential equation. This equation is then solved by a finite-difference method on a high-speed digital computer. Fayers and Sheldon5 obtained the solution of the one-dimensional displacement equation by directly replacing the differential equation by a finite-difference equation. The effects of capillary pressure and gravity were in- cluded in their solution. Here, since the movement of the foot of the saturation front is governed by a separate equation, the elapsed time in attaining a particular saturation profile cannot be obtained. The results of these two papers indicate that the inclusion of capillary forces eliminates the triple-valued Buckley-Leverett saturation profiles. In the present paper, the one-dimensional displacement equation for a homogeneous permeable medium, including the effects of capillary and gravity forces, is solved. The method of solution resembles that described in the paper by Douglas, et al, since it involves a similar transformation of variable. However, it extends their work in that the effect of gravity is included and, in addition, pressure profiles may be calculated. Also, the functions of saturation [kro(S), krw(S) and Pc (S) ] required are entered in tabular form rather than as low-order polynomials. This simplifies data preparation and permits the use of a greater range of function types. Unlike the method of Fayers and Sheldon, the corresponding elapsed time required for the development of each saturation profile is calculated and, also, saturation profiles may be calculated after breakthrough. THEORETICAL CONSIDERATIONS The dimensionless form of the one-dimensional displacement equation for a homogeneous porous medium as obtained from Darcy's law and material balance relations can be written as follows.

By Arthur F. Taggart

The following conclusions on the work of the Hardinge mill are based on data furnished to the writer by the Hardinge Conical Mill Co. in the form of the mesh cards hereto appended. Energy units (E. U.) and relative mechanical efficiencies (R. M. E.) are computed by the "volume method" of Stadler.' Screen apertures used are the average apertures of testing screeps of the meshes given. i . Card 122. June 28, 1912. Vipond Porcupine Mines Co., Ltd., Schumacher, Ont., Canada. Ore from mill bin. Gangue, quartz and basalt. 4.5 ft. by 13 in. ball mill, Capacity, 48 tons per 24 hr. Charge, 4,000 lb. balls. Speed, 33 rev. per minute. Horsepower, 15 to 17. Water, 100 per cent. by weight. (50 per cent. ?) Product deslimed and oversise reground in pebble mill, see Card 113. Feed to mill through 2-in. mesh. Mesh Feed, Per Cent. Discharge, Per Cent.. + 1in. 5.50 ....... + 3/4. 28.00 + in. 30.00 ...... + 1/4in. 19.72 ....... + 10 10.87 2.10 + 20 2.42 8.00 -20 3.51 .....,. + 40 ....... 22.68 + 60 ...___ 10.50 4-80 ....... 11.80 + 100 ....... 3.90 -100 ....... 40.15

Jan 1, 1916

By Morgan Walker

INTERMITTENT injection of gas in gas-lift pumping is a variation of the common practice in that the gas is' .delivered to the well for a short, period, called the "on time," followed by a period during which none is admitted, called the "off time," instead of being admitted continuously at a constant rate or by intermittent flowing in which it is occasionally delivered to the well in just sufficient quantity to flow off the accumulated head of fluid. The term "gas" is used throughout this discussion but it should be remembered that in so far as the operation is concerned either air or natural gas may be used. The equipment at the well is the same as commonly used in gas-lift installations and gas may be admitted to either the tubing or the casing. It seldom occurs that all the wells on a lease can be pumped economically by intermittent injection from one header. Wells that. have flow characteristics which permit their being handled together have their intake lines grouped at a central compressor station. Well groups may consist of two or more wells. The total volume of gas delivered by each group of compressors goes to one well at a time through a quick opening valve, each well connected to the header receiving its charge of gas in turn. Special cases may require a deviation from this arrangement. The distribution of the gas to the different wells is effected by an automatic timing device which operates quick-opening valves on the intake lines. The timing mechanism may be actuated by electricity, liquid or gas pressure. The essential factor in the operation of the timing mechanism is that as one intake valve is closed another must be opened.

Jan 1, 1928

By James M. Stapleton

IT has long been recognized by blast- furnace men that correct top distribution of materials is very important in efficient and economical furnace operation. Thousands of experiments on top design, filling, sizing, and other operations have been carried out to improving furnace performance by securing uniform distribution. Many of these experiments have worked out satisfactorily and have been passed along to the industry. Many of them have been discarded and forgotten. It has been the custom to judge the results of such experimentation by the results shown in improved or lowered furnace efficiency. While the effect on furnace practice will have to continue to be the final criterion of experimental changes, it has always been a desire of blast-furnace men to ascertain the reason for failure or success. Efficiency in the blast furnace approaching the maximum can be measured in several ways: (I) by actual operating results as revealed in the coke rate and tonnage figures, and (2), in the degree to which the top gas approaches the limiting ratio of CO/C02 for the reduction of iron oxide by CO gas. This ratio is shown in the equilibrium curve in Fig. I for the system Fe-O-C and CO2-CO-C. The closer the top gases approach this limiting ratio (set at 1.08 by Martin1 because of the effect of limestone calcination) the more efficiently we may expect a furnace to operate. The fact that low CO/C02 ratios parallel eficient operating performance caused us to investigate the cause of good or poor distribution and the effect of filling and other changes on furnace operation. Heretofore it has been possible to take a sample of furnace gas (usually from the dust catcher) and from it determine how closely the reducing gases were to the ideal or limiting value as set by the equilibrium diagram. However, to find just where in the top area the distribution was distorted and the top-gas CO/CO2 ratios were distant from equilibrium values has been a difficult and expensive investigational procedure. In an effort to overcome this difficulty, apparatus was designed to take gas samples and temperatures across the top radius of the furnace. It was hoped that with the aid of this apparatus traverse sampling of the ascending gases could be simplified, and the cost of sampling substantially lowered. Routine experimenting could then be maintained and results checked with furnace operation. It must be emphasized that a traverse sampling is necessary for a true picture, as single samples at any one point are unreliable. This statement can be verified by an examination of Tables 3 to 6, showing results obtained at our furnaces in a large number of tests. APPARATUS The design of the equipment for taking the samples was governed by the need for providing a simple, routine test that could be performed fairly quickly without adversely affecting normal furnace operation.

Jan 1, 1943