Search Documents

By Thomas V. Falkie

These are exciting times for the coal mining community. Although the industry is in the middle of a healthy boom, there are strong forces tending to counteract or at least temper the rate of growth. There are many pushing and pulling factors of interest to mining people, and a few salient ones will be mentioned here. Primarily because of a tremendous demand for energy, a demand that can't be met by other fuels, the coal industry is in boomsville. Another contributing factor to this situation is the increased overseas demand for metallurgical coal. These demands are being counteracted by a lack of people, the lead-time required to develop new capacity and wildcat strikes, among other things.

Jan 1, 1971

By C. K. Donoho

SILICON is used in almost all commercial steels; up to about 0.20 pct in killed wrought steels and 0.50 pct in steel castings. Above about 0.50 pct in wrought steels and 0.70 pct in cast steels, silicon is considered an alloy. As an alloy, silicon is useful for several purposes: (I) for its effect on magnetic properties of parts for electrical apparatus; (2) for increasing the yield strength of carbon and low-alloy steels without too much sacrifice of ductility and weldability; (3) for adding hardness and toughness to spring and chisel steels; (4) for adding resistance to scaling and carburization to heat-resistant steels; and (5) for its graphitizing effect in graphitic steels. In acid electric steels for casting we are principally interested in the effect listed second; i.e., increase of strength with minimum sacrifice of ductility.

Jan 1, 1947

By Edward H. Robie

Jan 1, 1971

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,' Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o's. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze's (and McAdam's) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By Arthur West

It is the purpose of this paper to describe briefly some recent large power stations for blast furnaces, where the blast is exclusively supplied by gas engines using furnace gas. The stations are given in the chronological order in which they were designed, in order to indicate the various improvements suggested by experience. Fig. 1 shows the blowing-engine station of the Bethlehem Steel Co. at Bethlehem. Although the picture shows only five blowing engines, the house now contains 11 engines. In the diagrammatic plan the arrow shows the position and direction of camera. This station handles five modern blast furnaces of 450 to 500 ions capacity each. In this, as in all the other stations described in this paper, each furnace is blown by two single tandem gas engines. Ten engines are thus required for five furnaces, leaving one single tandem spare engine. This spare capacity has been shown by several years' experience at Bethlehem to be adequate to insure continuous operation. The engines in the Bethlehem station are right hand and left hand, arranged in pairs. The outboard bearings of each pair are close together so that there is not room for passageway between them. On the right of the picture are shown the inclined drums communicating with the cold-blast lines outside of building, so that any engine may be operated on any furnace. The illustration shows four cold-blast gate valves with pipes passing through wall, but since the photograph was taken the drums have been extended to take care of a fifth valve for a fifth furnace. At the extreme back of the picture can be seen the tubs of three twin vertical-horizontal Southwark steam blowing engines, which, although of modern design and as good as new, are not operated because of the greatly reduced blowing cost shown by the gas blowing engines. The next station built is shown in Fig. 2. This is the plant of the Minnesota Steel Co. at Duluth, Minn., and is at present constructed for five engines, to handle two furnaces, with one spare engine. The engines are of practically the same size as those at Bethlehem. Instead of being arranged in right-hand and left-hand pairs, as at Bethlehem, all the engines are of the same hand; this arrangement has some ad-

Jan 1, 1915

By Gail F. Moulton

The production of petroleum in Illinois in 1928 was approximately 6,500,000 bbl., a decline of about 500,000 bbl. from the previous year and of about 1,500,000 bbl. from 1924. Production increased about 200,000 bbl. in Indiana to slightly less than 1,000,000 bbl. Production for 1929 is estimated at approximately 6,000,000 bbl. for Illinois and 1,000,000 bbl. for Indiana. Illinois Because production from most of the wells in the state has declined to a small daily average and the low prices for crude oil discouraged wildcatting, the number of wells drilled fell below that for any previous year since the development of commercially important production in the state. The Ohio Oil Co. discovered a pool of apparent commercial importance in southwestern Illinois near Dupo, in St. Clair County, and favorable showings of oil were encountered in a well in southeastern Illinois, near Harrisburg in Saline County. New production from the Dupo area is expected to check the rate of decline for the state. Thc following tablel summarizes field developments for 1927 and 1928 (for important detail by counties see notes at foot of table): 1027 1928 Completions........................................... 162 145a Initial production, bbl.................................. 2244 1840b Dry holes........................................,.... 66 58" Gas well completions................................... 13 8d 0111 wells abandoned.................................... 45" a Crawford, 44; Lawrence, 28; Wabash, 40. b Crawford, 501; Lawrence, 403; St. Clair, 165 (4 completions); Wahash, 668. o Crawford, 12; Wabash, 19. d Crawford, 6. b Lawrence, 21; Wabash, 15. The discovery well in the Dupo field in St. Clair County, produced about 150 bbl. per day from the Trenton lime at 660 ft. It is located in a northern extension of the Columbia-Waterloo anticline on which the Waterloo pool was developed in 1921. The best information on the.

Jan 1, 1929

By R. A., D. L. Sponseller, Flinn

Using specially del'eloped titanium nitride crucibles and a pressurized syslem, it has been possible to determine the solzibilitv of liquid calcium in liquid iron and iron-base alloys. At 2925°F the solubility is 0.032 wt pet Ca in pure iron. The solubility is increased by aluminum, carbon, nickel, and silicon additions, and lowered by additions of gold. An inflection in the calcium-solubility curve occurs as carbon is added to iron. At approximately 0.87 Wt pet Ca the CaC, phase replaces liquid calcium, and the calcium concentration de- creases as more carbon is added to the iron. The maximum solubility, 0.36 wt pet Ca, was obtained in iron containing 10.5 wt pet Si. The data have important implications regarding the use of calcium in process metallurgy, as well as providing an interesting test of theories of metallic solutions. Reasonably good agreement is found with theories of Alcock and Richardson and of Wagner, and criteria are suggested which permit these theories to be applied more readily to systems of this type. AT the present time relatively little is known about the factors influencing solubility in liquid metals. Information of this type is important for such matters as the control of impurity levels in liquid metals, the use of magnesium in ductile-iron production, and the use of liquid-metal alloys as fuels and coolants in nuclear power plants. One important example of restricted solubility concerns the extent to which liquid calcium will dissolve in liquid iron. This is a matter of considerable interest in view of the strong potential of calcium for removing certain impurities in steel,. as well as the ability of calcium to desulfurize, inoculate, and produce spheroidal graphite in cast irons.' Since ferrous materials normally contain other elements in addition to iron, the interactions of third elements with the Fe-Ca system are of interest. In view of the foregoing, this investigation was conducted to determine the solubility of liquid calcium in liquid iron and the effects of various third elements upon the solubility. For reasons of theoretical and engineering importance, the elements investigated were aluminum, carbon, gold, nickel, and silicon. Numerous attempts were made in the early part of the present century to determine the solubility of calcium in both liquid iron and steel, employing a variety of open-melt and closed bomb-type systems.2-4 From the results of these tests Wever concluded that calcium is insoluble in liquid and solid iron.5 These investigations were unsatisfactory in that they failed to insure the presence of a liquid layer

Jan 1, 1964

By R. F. W. Pease, R. A. Ploc

A scanning electron microscope with a resolving power better then 100Å has been developed for the direct examination of surfaces. This instrument was used to study iron undergoing oxidation at 500°C. It was found that the electron current in the scanning electron microscope was low enough (about 10-atrzp) to have no observable effect on the growth of the oxide. "Armco " iron, when oxidized, exhibited an oxide film whose thickness and whiskey population varied with pain orientation; but purer iron, when oxidized, exhibited no such pain dependence and whisker occurrence appeared to be caused by impurities. UNTIL recently most surfaces of opaque specimens could either be studied with a light microscope or, if higher resolution was required, by viewing a replica of the surface in a transmission electron microscope. Direct electron microscopy of a surface has, in general, proved difficult owing to excessive foreshortening and the poor image quality obtained. The scanning electron microscope, however, offers an alternative method of directly viewing a surface without these disadvantages. At low magnification it offers a much larger depth of focus than the light microscope, and at high magnifications it offers much higher resolution (about 100Å). PRINCIPLE OF THE SCANNING ELECTRON MICROSCOPE A schematic diagram is shown in Fig. 1. The electron optical system consists of a gun followed by a series of lenses which focus the electron beam onto the surface of the specimen. The beam is scanned in a rectangular raster across the specimen surface and, by amplifying the secondary electron current from the 'pecimen, a picture of the specimen surface is built UP sequentially on the face of the display cathode-ray tube. The magnification of such a system is given by the ratio of the scan amplitude on the display cathode-ray tube to

Jan 1, 1965

By H. H. Podgurski

Above 200°C the observed increase in the apparent solubility of hydrogen in low alloy steels caused by cold work is attributed to the formation of methane in microvoids. This methane can be isolated quantitatively, and furthermore, the amount of methane is in accord with the equilibrium 2H2 + Fe3C = CH4 + 3Fe. The micro-void volume, calculated from the methane content via the equation of state for methane, corresponds approximately to that calculated from the measured density decrement produced by cold work. THIS investigation was undertaken with the intent of employing the hydrogen atom as a probe in detecting specific crystallographic defects in cold worked steel. It was expected that different degrees of chemical interaction of hydrogen with the various types of defects could be utilized. The original aim was to assign concentration values to defect sites. The success of this approach requires that experimental conditions can be attained under which lattice-dissolved hydrogen equilibrates primarily with only one type of defect. A set of experiments which appeared potentially to embody these requirements was described several years ago by Keeler and Davis.1 They noted in the case of a mild steel (low carbon) that the solubility of hydrogen between 200° and 400°C near atmospheric pressure was notably increased by cold working the steel. The observed solubility was an order of magnitude greater than the normal lattice solubility. * Although the Keeler and Davis studies suggested that the density decrement effected by their cold-working operation might be related to the anomalous solubility of hydrogen, they offered no explanation of the relationship between the two effects. Prior to this work, Darken and smith3 had noted a similar effect of cold work upon enhanced sorption of hydrogen by steel when charged by acid pickling. In the light of present-day concepts, interaction between lattice-dissolved hydrogen and dislocations was strongly suggested. More recently, Hill and Johnson,4 working with a

Jan 1, 1962

By D. M. Kehn

A method has been devloped for chromatographic analysis Of the vapor and liquid phases Of a a system containing methane to components having 20 or more carbon atoms. The method uses a windowed equilibrium cell in which volumetric phase behavior of the system can be observed accurately and from which small samples of gas or liquid can be withdrawn for analysis. Analyses are made using two chromatographs, one for the lighter and one for the heavier components in a sample. Combination of the two analyses yields a detailed analysis of the gas or liquid sample. The complexity of the condensate heavy ends is evident from the chromatograms of these fractions, and the predominance of the paraffin hydrocarborn serves as a useful marker in interpreting the chromatograms. The K-values obtained in this analytical method are presented for a high-pressure condensate system and predict closely the observed volumetric behavior of the system. INTRODUCTION Quantitative analysis of hydrocarbons from natural gas reservoirs is necessary for several reasons—to calculate the amount of sales gas produced, to calculate the amount of natural gasoline produced, to plan a liquid recovery system, or to calculate the potential economic value of a reservoir produced under one or more of several different conditions. Analysis of natural gas fluids produced to the surface consists of identifying and computing the mol fraction of each component of the mixture. Although methane is the predominant component, varying amounts of ethane, propane, butane, pentanes and heavier components are also present. Materials containing up to 30 carbon atoms occur in amounts which decrease with increasing molecular weight. However, the quantities of components in the 20 to 30 carbon atom range are usually so small that their importance is negligible, and they are undetect-able in natural gas by ordinary analytical methods. All the components up to those having 20 carbon atoms may sigsficantly affect phase behavior, however. Commonly, only the methane-through-pentane fraction is analyzed quantitatively for each component, while components heavier than Pentane are lumped and repored as "hexane- plus". Expensive, tedious techniques are required for analysis of this fraction. Consequently the detailed analyses needed for prediction of reservoir behavior are usually undertaken only when major gas fields are being developed. The need for complete analyses of condensate systems is apparent when it is recalled that most gas fields are produced by pressure depletion. As the pressure declines, some of the heavier hydrocarbons are lost as liquids which are in the reservoir. In many instances the amount of liquid in equilibrium with the gas phase at high pressure constitutes only 1 or 2 mol per cent of the total system. Flash calculations generally must predict the actual amount of liquid with an accuracy of a few per cent in order to be useful. This retrograde condensation has been understood for years, but accurate correlation methods to permit quantitative prediction of phase behavior in the retrograde region are not presently available. The increasing importance of natural gas has made accurate prediction of phase behavior and composition of produced natural gas streams an economic necessity. The work reported here was undertaken to provide a rapid, economical method for obtaining the vapor-liquid equilibrium information needed to predict accurately the composition of the fluids produced from a gas reservoir throughout its life. TO develop this method, a pressure cell equipped with windows was designed and built for observing the volumes of liquid and gas present at reservoir pressures and temperatures. Use was made of established chromatographic methods for rapid and detailed analysis of both phases. This paper describes the equipment and techniques developed for obtaining vapor-liquid equilibrium data, presents the results of analyses of a condensate system, and indicates the usefulness of these data in predicting hydrocarbon phase behavior. DESCRIPTION OF EQUIPMENT USED The equipment used in obtaining the required information on phase behavior and the complete analysis of hydrocarbon mixtures through C, will be described first, followed by a discussion of the operation of the equipment. It will be helpful, however, to consider first a brief outline of the technique used. A sample of separator gas and liquid is charged to the windowed cell (see Figs. 1 and 2) where volumetric equilibrium phase behavior at reservoir pressures and temperatures can be determined. Then samples of the coexisting phases are withdrawn. The methane-through-pentane fraction is analyzed with a chromatograph equipped with a hot-wire detector, and the pentane-plus fraction is analyzed with a second chromatograph equipped

Jan 1, 1965

By Robert H. Richards

Jan 1, 1883

By A. L. Slaughter

The Homestake mine, located in western South Dakota, was discovered in 1876. The first reported production was in I 878. Total production through 1965 is 6,554,249 troy ounces of silver and 27,961,276 troy ounces of gold, worth $987,000,000 at present prices. Precambrian sedimentary formations at Lead total 20,000 feet. The Poorman Formation, the oldest, is chiefly ankerite carbonate. The Homestake Formation is iron-magnesium carbonate. The younger formations are argillaceous with some quartzites. The Cambrian Deadwood Formation unconformably overlies the Precambrian. All are cut by Tertiary intrusives. Sideroplesite schist of the Homestake Formation was converted to cummingtonite schist in the zones of higher-grade metamorphism. The Precambrian rocks show the effects of extreme isoclinal folding. A second stage of folding ( cross folds) may have been caused by the Tertiary intrusives. All folds plunge to the southeast. The Homestake ore bodies are pipe-like replacements of the Homestake Formation in zones of cross folding. It is believed that dilatation of the schists has increased permeability in these zones. Chloritization of the schists is the most widespread effect of the mineralization which is divided into four stages. Principal minerals of the first stage are quartz, chlorite, and arsenopyrite; in the second stage, quartz, ankerite, and pyrrhotite. In the third stage only pyrrhotite was deposited. The fourth stage followed the intrusions of Tertiary dikes and deposited mostly pyrite and calcite. Gold accompanies all stages and is always the last mineral to be deposited. It is most closely associated with arsenopyrite of the first stage but can be interpreted as having been deposited during the fourth stage and superimposed on the products of the earlier stages.

Jan 1, 1968

By G. D. Rieck, M. M. P. Janssen

Chemical diffusion coefficients and heats of activation for diffusion in the NizAh fy), NiAl (6), and Ni3A1 (E) intermetallic phases and the solid solution of aluminum in nickel (( phase) were calculated from layer growth experiments. No finite diffusion coefficient for the NiAl3 ((3) inter metallic phase could be calculated. The values of the diffusion coefficients are dependent both on the method of calculation and the type of diffusion couple. The heat of activation for diffusion in the y phase was found to be 47 kcal per mole in the temperature range oj 428" to 610°C. Heats of activation of 41, 12, and 48 kcal per mole were found for diffusion in the 6, E, and ( phases, respectively , in the temperature range of 655" to 1000°C. Experiments with markers in the diffusion zone demonstrate a very pronounced Kirkendall effect. It appears that only aluminum atoms take an active part in the diffusion process during the formation of the 0 and y phases at temperatures of about 600°C. During the formation of the 6, E, and < phases at higher temperatures only nickel atoms are moving. It is suggested that the great stability of the intermetallic compounds in the Ni-A1 system governs the Kirkendall effect. SOME factors controlling layer growth during inter-diffusion in the Ni-A1 system (phase diagram, see Fig. 1) were studied by Castleman and Seig1e.l&apos;~ They found the NiA1, ((3) and NiAl3 (y) intermetallic compounds to appear in the diffusion zone of Ni-A1 couples at annealing temperatures of 400" to 625°C; the NiAl (6) and Ni3A1 (E) intermetallic compounds appeared in y-Ni couples at annealing temperatures of 800" to 1050°C. These authors carefully examined metallographically Ni-A1 couples after 340 hr annealing at 600°C. Besides the (3 and y phases they found very thin layers of the 6 and E phases. ~n~erman~ and Castleman and Froot4 observed a much more rapid growth of the 5 and E phases at 600°C in Ni-A1 couples in case a crack was present at the /3-A1 interface. Numerous layer thickness measurements carried out by Castleman and Seigle on the y phase prove that the layer growth of this phase obeys the parabolic law after a certain transient period. From this they concluded that the layer growth of the y phase is controlled by volume diffusion. The growth of the 13, 6, and E phases appeared to be volume-diffusion-controlled also. The authors estimated that at 600°C and at atmospheric pressure Dp was 1.8 x lo-"ll sq cm per sec, D, 9.1 x 10" ™ sq cm per sec, Qp 27 kcal per mole, and Qy 31 kcal per mole. The present work was carried out to obtain more quantitative data about the kinetics of growth of the phases of the Ni-A1 system and the reactions that occur during the formation of these phases. Because in this system the diffusion process results in the formation of several distinct intermetallic compounds, the current term reaction diffusion is used in the title of this paper. In order to obtain layers of the fl phase compound of uniform thickness, a new technique for preparing diffusion couples was developed. The kinetics of growth of the y phase in 6-Al, E-Al, and Ni-A1 diffusion couples was studied at different temperatures. The kinetics of growth of the 6, c, and ( phases in Ni-y, Ni-6, and Ni-c diffusion couples was also studied at different temperatures. The calculation of the diffusion coefficients Dp and Dy by Castleman and Seigle are critically considered in this paper; by means of a revised method of calculation more reliable val-ues of , and Dg were found. These values are in good agreement with the values of the diffusion coefficients obtained by the method of Boltzmann-Matano. From the temperature dependence of the diffusion coefficients the heats of activation for diffusion were calculated by means of an Arrhenius-type equation. The investigation of the Kirkendall effect has been used to obtain information about the ratio of the intrinsic diffusion coefficients of the separate atoms5 and the mechanism of diffusion. Moreover porosity as a result of a distinct Kirkendall effect would be of practical importance in connection with the bonding of diffusion coatings. The analyses of the diffusion couples were carried out by metallographic methods. The values of the concentrations at the phase boundaries and the concentration profile in each of the phases, which are needed for the calculation of diffusion coefficients, were obtained by electron-pro be X-ray microanalysis. EXPERIMENTAL PROCEDURE A) Materials for Diffusion Couples. The intermetallic compounds 6 (50 at. pct Ni) and E (74 at. pct Ni) were prepared from the pure metals by high-frequency induction melting in argon atmosphere. Use was made of aluminum wire (99.99 wt pct Al) and nickel sheet (99.95 wt pct Ni). The 6 and E phase melts and the nickel shiet (thickness 0.1 and 0.5 mm) used for preparing diffusion couples were annealed for 64 hr at 1200°~ for homogenization and grain coarsening (final crystal size 1 to 3 mm). composition and homogeneity of the intermetallic compounds were checked by mi-crohardness measurements and X-ray diffraction. From the 6 and E phase melts discs of 0.5 mm thickness were prepared by means of a water-cooled rotat-

Jan 1, 1968

By Robert E. Bush, E. S. Mardock

The objective of this paper is to present practical methods of applying radioactivity logs to problems of interest both to those engaged in evaluating fundamental reservoir data as well as to those engaged in subsurface structural work. The basic theories underlying the operation of radioactivity logging methods are briefly discussed along with some of the problems arising in the interpretation of the log. Relative methods of quantitative interpretation are described, with a discussion of relative reference lines and specific examples are given showing the application of these relative quantitative interpretation methods. To show the variation of the methods described, specimen wells penetrating formations widely divergent in point of geologic age were selected to demonstrate the application. A relative reference line is determined for the Neutron Curve and by comparison to known petrophysical data such as porosities from diamond cores, a direct quantitative relationship is developed. The application of this relative calibration curve to logs of unknown wells will permit a reasonably accurate determination of porosity in limestone and dolomite formations. Specific examples are given showing the application of these relative methods of interpretation to logs of the Smackover limestone in Louisiana, the Edwards limestone and dolomites of South Texas, and Permian dolomites of West Texas. Radioactivity logs have been used extensively by the petroleum industry for a number of years and recognition of their value has grown steadily, not only as tools to aid in the solution of specific stratigraphic problems, but also as potential sources of the basic data necessary for the estimation of net pay and reserves. The value of radioactivity logs for stratigraphic work has been pointed out in the literature,1,2,4,5,6 and now has long been recognized by the industry, but the quantitative application of the logs has advanced but little beyond the stage of a strong conviction that radioactivity logging curves will some day provide the information on such important quantities as the porosity and the liquid saturation of the formations. During the past few years the staffs of the Lane-Wells Company and Well Surveys, Incorporated, have devoted a great deal of time, thought, and experimentation to the relationships existing between radioactivity curves and the lithologic conditions encountered, and this paper is, in a manner of&apos; speaking, intended as a progress report of this work and includes suggestions which the authors have found useful in the interpretation of radioactivity logs. The section on theory is not intended as a complete exposition of the physical processes involved, but rather as a brief introduction to the reader of these processes so that he may acquire a better understanding of the behavior of the radioactivity curves under the varied conditions encountered in normal well logging. Three relative methods for using neutron logs for the quantitative estimation of porosity in limestone or dolomite are presented. These methods are based on the comparison of logs and porosity data from wells in Louisiana, South Texas, West Texas, and New Mexico. These areas were selected because not only were there more core data available from these areas but also the majority of these data were from limestone or dolomitic zones. The correlation between core data and logs is simpler for limestones and dolomites than it is for sandstones due to the fact that sandstones are more complex than limestones and differ more widely among themselves as to composition of cementing materials, siltiness, etc. When data applicable to the various types of sandstones are available, the authors hope to present a discussion similar to this paper covering sandstones or possibly a more general discussion covering all types of reservoir rocks. The relative methods for estimating porosity which are presented in this paper fall short of the absolute method sought. However, these methods possess the advantage that they can be applied to almost any neutron log as long as the range of application is held within the limits imposed by the local lithologic conditions which prevailed during calibration, i.e., these methods are for short range application only. THE THEORETICAL BASIS FOR RADIOACTIVITY LOGGING The two redioactivity logging curves commercially available today are the

Jan 1, 1950

By Carl F. Floe, John Chipman

The system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100" to 1500ºC., and pressures from about 20 mm. of mercury to somewhat above atmospheric. Review of Previous Work The solubility of gases in most liquids has been found to obey Henry&apos;s law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as O2, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts&apos; law. It may be recognized as a special case of Henry&apos;s law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: 2M+G2=2MG K=(MG)2 /M2 X PG2 [I] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: MG = K1 vPG2 [2 Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: 6Cu + SO2 = Cu2S + 2Cu2O [3] K= Cu2S X (Cu2O)2 i - (Cu)6(Pso2) [4] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: K1 =V3SO2 /Pso2 or

Jan 1, 1941

By Ian MacGregor

INTRODUCTION I retired in 1977 and have been enjoying myself ever since doing odd jobs for various people - on occasions, politicians. I commend it to you as post retirement - get involved in situations that nobody else will take on. It produces all sorts of excitement, it is a lot of fun and, courtesy of the media, you provide great raw material for their current Punch and Judy shows. The example of the adventures in the Escondida financing made me think about the history of the minerals industry in the United States. In order to see more clearly what is going to happen in the future, we have to look at the past and what we have learned, and try to extrapolate from that a scenario for the future. This paper is about global material cycles and the financial needs of the extractive industries. Since about 2,000 years B.C. we have been living in the Iron Age. Since about 4,000 B.C. we have been living in the Copper Age. These have been the two foundations of modern industrial society. Understanding the use of metals and materials helps us understand the civilization in which we live today. Let me focus more closely on the United States, particularly in this century. In the first two-thirds of this century the United States was growing and expanding and developing. It was providing for its inhabitants a society which was enjoying the benefits of a rising standard of living, improved opportunities and the ability to support a population growing at quite a dramatic rate. It is still growing. In the Department of Commerce, there is a clock that shows how many people there are in the United States. It turns all the time; the numbers are going up. On January 21,1980, when Ronald Reagan was sworn in as President, the number on that clock was a little over 220 million, and in the last week before he left, it was travelling towards 245 million. During his period in Washington, we have added , the equivalent of one total state such as California. That gives the dimensions of the U.S. appetite for raw material inputs. The inputs are of critical importance. COMPARATIVE ADVANTAGE During the first two-thirds of this century, the minerals sector enjoyed comparative advantages. There was a clear understanding of the importance of minerals enshrined in the tax legislation of the country from the early decades of this century - the depletion allowance. No other country identified as clearly that the supplies of minerals were finite. As they are used up, just as with a wearing-out machine, one must get capital back to replace the resource when the time comes. Within the last decade, that idea has been questioned and criticised. It is now seen as giving money away to a preferred part of the economy, instead of recognizing what depletion is all about. In previous times it insured that the U.S. always was able to regenerate the capital in its minerals industry, so that it could remain competitive. The U.S. had plenty of everything, including energy. We had a growing population. Equally important, we had an agriculture that led the world in productivity, even as far back as the turn of the century. It continues to do so. We still retain that comparative advantage, an ability to produce our foodstuffs in quantity and quality at excellent cost. Look at another ingredient of our comparative advantage, the energy position. We ran through the first two-thirds of the century with ever- decreasing energy costs. In the 1940s and 1950s the coal industry went into a decline. Why? Because the $3.00 - $5.00 a ton cost of mining coal in the U.S. represented relatively expensive energy. A ton of good grade bituminous coal contains 25 million BTU&apos;s. $0.20 a million BTU&apos;s represents $5.00 a ton at the pithead. That price was undermined by the increasing ability to find petroleum at even lower costs. At the apex of the growth of development of the American dominated

Jan 1, 1990

By T. W. Healy, P. Somasundaran, D. W. Fuerstenau

The flotation behavior of quartz in the presence of alkyl ammonium acetates as a function of alkyl chain length has been interpreted in terms of hemi-micelle formation at the solid-liquid interface. The van der Waals cohesive free energy that is responsible for hemi-micelle formation has been found from these results to be 1.0 kT per CH2 group. This is in excellent agreement with literature values obtained from research on the properties of micelles in bulk systems. Collectors of the type CH3(CH2)n-2CH2-P, where P is a polar group and n is the number of carbon atoms in the straight alkyl chain, will induce flotation of an appropriate mineral at lower concentrations as n increases. This reduction in collector concentration with increasing n has been reported for such systems as xanthates on sulfides1,2 and amines on quartz.&apos; The effect of chain length of alkyl surfactants on such solution properties as conductivity,&apos; surface tension,&apos; and solubility6 and such interfacial properties of solids as contact angle7 and electrokinetic potential8 have received considerable attention, but only limited quantitative descriptions of the effects have been given. The electrokinetic studies of alkyl amine salts on quartz indicated that the solution concentration of collector at which the marked change in electrokinetic potential of quartz occurs decreases systematically as the length of the alkyl chain increases. The aim of the present work was to obtain a quantitative description in terms of current theories of flotation of the effect of the hydrocarbon chain of alkyl ammonium acetates on the flotation behavior of quartz. BASIC PRINCIPLES The marked changes in electrokinetic potentials of quartz in dodecylammonium acetate (DAA) solutions were postulated to result from the association of adsorbed collector ions into two-dimensional aggregates, called hemi-micelles.9 Subsequently, the rapid increase in flotation rate of quartz was shown to coincide with hemi-micelle formation." We would like to discuss briefly the concept of hemi-micelles in terms of recent interpretations of micelles in bulk solution. Micelle hypothesis: In dilute solutions, alkyl ammonium and related salts behave as ordinary strong electrolytes, but at a certain concentration there is a marked change in physical properties of the solutions, e.g., in equivalent conductance, transport number, freezing point lowering and viscosity. To account for these phenomena, McBainl1 introduced the concept of micelles, which are aggregates of long-chain ions. It is believed that the ionic heads of the constituent ions of the micelle are in contact with water, whereas the nonpolar groups turn away from it and are in contact with each other. Work must be done to bring these charged polar groups together, but energy is gained (i.e., so called van der Waals cohesive energy) when hydrocarbon chains are expelled from the water and allowed to associate. For a given polar group, the tendency to form micelles will therefore strongly depend on the hydrocarbon chain length. Theoretical treatments of micelle formation by Shinoda12 and Phillips13 and others lead to the following expression for the concentration at which micelles form (the critical micelle concentration or cmc) in aqueous solutions of long- chain electrolytes

Jan 1, 1964

Discussion of the paper of B. H. Dunshee, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 30, August, 1913, pp. 1511 to 1531. GEORGE E. MOULTHROP, Butte, Mont.:-The recording for the first time by Mr. Dunshee, in a readily usable form, of the various systems of square-set framing applied in the Butte district is a valuable contribution to mining information. The many different methods of framing employed, due to the individual ideas of superintendents and foremen of segregated companies, have given full opportunity to determine the best framing for the conditions as found in these mines, and the final adoption of a system uniform for all the mines has come about through a study of these various methods and an experience covering a period of many years. The sawed 10 by 10 in. and 12 by 12 in. timbers undoubtedly give the best satisfaction; and the style of framing the sawed timber that under all conditions has given the best practical results is that used in the Anaconda group and other mines, described and recommended by Mr. Dunshee. In this framing the posts have a horn 2 in. high and 6 in. square, the cap end having dimensions of 3 by 6 in. Instead of the framed girt shown in the drawings of the Anaconda group, the 6 by 10 in. girt adopted at some other mines, which fits into the cap and post framing with no other preparation than cutting the timber to the necessary length, fills all the necessary requirements for strength and affects a material saving in timber and labor. This, as Mr. Dunshee states, is without doubt the type of framing which would be adopted as a standard for 10 by 10 in. sawed timbers if sawed timber sets were to be used in the future generally. But saw-timber for the mines was becoming scarce and expensive, and round timber for the square sets furnished an alternative which provided, at greatly reduced cost, material which in every way supplied the requirements of the mining conditions. The use of the round timber with a satisfactory framing makes available a conveniently located and large source of supply which up to this time has served no useful industrial purpose. Particularly is this true of small timber, which is still standing in great quantities in the forests where the trees more desirable for commercial purposes have already been cut and marketed.

Jan 11, 1913

By N. P. Peterson

THE Castle Dome copper deposit is of the porphyry type and occurs in a body of quartz monzonite intruded into the pre-Cambrian formations and possibly into the lower part of Paleozoic limestones. The hypogene sulphide minerals include pyrite, chalcopyrite, and a little molybdenite, sphalerite, and galena. Pyrite and chalcopyrite are disseminated or occur in small closely spaced veins. The hypogene mineralization shows distinct zoning in the distribution of pyrite and chalcopyrite, so that the mineralized area can be subdivided into pyrite and chalcopyrite zones. Supergene enrichment, though not extensive, played an important part in the formation of the ore body, the chalcopyrite zone being the protore. Several thin, gently dipping, diabase sills occur in the mineralized area, and the copper content of the rock in and near these sills is substantially higher than average. The formation of the ore body was caused by the combined effects of three forces: I. Zoning of the hypogene mineralization, 2. Richer copper metallization associated with the diabase sills, and 3. Supergene enrichment.

Jan 1, 1947

By M. Mathieu

The Rove tunnel is the means by which the canal from Marseilles to the Rhone Riverl penetrates the hills of Nerthe, lying between Mar- seilles harbor and Lake Berre, Fig. 1. The canal will communicate at sea level with both terminals. The original project planned a lock near the village of Marignane; but observations, pursued for more than three years, showed that the water surface gradient would average only 0.015

Jan 1, 1923