Search Documents

By S. K. Bose, P. K. Sahoo, S. C. Sircar, P. K. Jena

High grade manganese ores are utilized in metallurgical, chemical, and battery industries, whereas the low grade ores are not accepted for these purposes and hence get accumulated at the minehead. In the present study an attempt was made to solubilize the manganese value as its sulfate by roasting the low grade ore with a suitable sulfatizing agent followed by water leaching. The different parameters were determined in the laboratory scale. Based on these, kilogram scale experiments were conducted where an appreciable amount of manganese goes into solution during leaching.

Jan 1, 1981

[Alphabetic Section (Page 689): The letter immediately following the member's name indicates grade: M-Member, A-Associate, J-Junior. The numerals following member's grade indicate year of election. The letter following year of election indicates primary Divisional affiliation: A-Mining & Exploration F-Coal B-Minerals Beneficiation G-Petroleum C-Iron and Steel H-Industrial Minerals D-Extractive Metallurgy J-Council o f Education E-Institute of Metals K-Council o f Economics]

Jan 1, 1961

Jan 1, 1909

By H. H. Waller, D. L. Monroe, D. P. R. Smyth

ORIGINALLY slusher drift development was conventional, advancing the drift full 10x13-ft size at 6 ft per round. This proved dangerous and costly because the weak fractured rock of the orebody cannot be left raw for any length of time without its reacting with air to cause spalling. With this method of drift development ground conditions were worsened by many blasts and the length of time it was necessary for the drift to remain open. The problem was practically solved by driving 5x7-ft pilot drifts, then enlarging to 10x13-ft raw size by slashing with 50 to 60-ft diamond drill holes. Calculated explosive charges are used to avoid wall and roof shattering. Still more recently jacklegs and sectional steel replaced the diamond drills, resulting in the same work for less than half the cost, see Figs. 1 and 2. Crosscuts at right angles to the main haulage drifts, which cross through the center of the ore-body, divide the ore into 200-ft blocks. Eight slusher drifts on 50-ft centers draw from one block. The slusher floor is 11 ft above the rail, inclined at 1 pct grade, and the top is 18 ft below the undercut. The finished slusher drift is 102.5 or 120 ft long, depending on whether it is north or south of the crosscut. Drawpoints are staggered on each side at 17.5-ft centers. The completed drift is concreted and has an inclined ramp and a vent at the back. When crosscuts and gangways have been excavated and concreted and slusher stations installed, slusher drift development is carried out in 10 clear-cut stages: 1—Pilot drift is driven full length, 5x7 ft. 2—Station is excavated at half-way point in pilot drift. 3—Pilot drift is enlarged to slusher drift size by drilling. 4—Lower part of slash is blasted and mucked for floor concrete. 5—Floor is poured. 6—Inside upper half of slusher drift is blasted, mucked, and concreted. 7—Outside upper half of slusher drift is blasted, mucked, and concreted. 8—Drawpoints are excavated. 9—Drawpoints are concreted. 10—Concrete ramp and sheave protection recess are constructed at back end of slusher drift. A 5x7-ft pilot drift is driven full length on the center line of the proposed slusher drift using a jackleg and detachable bits on 7/8-in. hexagon steel. A 10-hp air-driven slusher and 36-in. scraper pull muck directly into cars in the main haulage crosscut, see Fig. 2. Operations are on a three-shift basis. One man mucks the previous round, drills, and blasts his round in a shift. Average advance is 5 ft per shift. When the pilot drift is completed, 7 ft of drift in the center section is enlarged to full raw slusher drift size of 10x13 ft, for the set-up to drill long slash holes. The pilot drift is slashed to full raw size from this station with jacklegs and tungsten carbide chisel bits on 7/8-in. sectional steel. Crews line the holes without trouble, working from controls established by the engineers, and the pattern of holes for the slash is arranged to give the least shattering effect

Jan 1, 1955

By Frederick C. Hull, Robert F. Mehl, Robert A. Colton

IT is known that pearlite forms from austenite by a process of nucleation and growth, and that the rate of formation of pearlite may be described by a rate of nucleation and a rate of growth 12 The manner in which these two quantities operate to produce the observed isothermal reaction curve has been analyzed in a paper published in 1939 3 Two types of process were described (I) that in which nucleation occurs at the grain boundaries of the parent phase, with the nodules growing toward the centers of the grains, initially as hemispheres and then after impingement as roughly radial-columnar structures, and (2) that in which nucleation occurs generally, with the nodules growing to full spheres until impingement with other growing nodules restricts growth Both cases are met in the formation of pearlite from austenite (Fig 1),2,3 the former, occurring near the knee of the S-curve has been named "grain-boundary transformation," and the latter, occurring at temperatures near AeI, has been named "group-nodule transformation " In developing our knowledge of the factors that determine the rate of formation of pearlite from austenite, it is important''' to obtain data on the rate of nucleation and the rate of growth of pearlite Such data, when obtained near the knee of the S-curve, will furnish information of use in understanding the actors that affect hardenability, when obtained at higher temperatures, such data will be useful in understanding the behavior of steels that during heat-treatment react to pearlite 2 It is the purpose of this paper to present data on the rate of nucleation and the rate of growth of pearlite in dependence upon composition, grain size, temperature,, and the degree of homogeneity of the parent austenite The studies are restricted chiefly to plain carbon commercial steels PREVIOUS DATA ON RAID OF NUCLEATION AND RATE OF GROWTH Data on the rate of nucleation and the rate of growth of pearlite have been published by Scheil and Lange-Weise,5 by Mirkin and Blanter,6,7 by Mehl,1 and by Dorn, De Garmo and Flanigan22 It is difficult to interpret the data, for in most cases too little information is given on austenitizing temperatures and times, the state of homogeneity of the austenite (presence or absence of carbide, etc ), austenite grain size, and mode of formation of pearlite at the temperatures given

Jan 1, 1942

By E. M. Frizzell

Introduction In 1956, the first mobile crusher was installed in a limestone quarry in Hover, Germany. These early mobile crushers solved the problem of wet and soft ground conditions that did not permit the use of haulage trucks due to the high cost of building and maintaining the haulage roads. Quarry operators also wanted to take advantage of continuous belt conveyor haulage systems and the resulting cost savings. European mines, particularly the coalfields, are in soft materials that allow use of bucket wheel excavators and their following continuous haulage system of belt conveyors. Quarry operators, with this background knowledge of belt conveyors in mining, easily accepted the conveyor concept, once in-pit mobile crushing solved the problem of size reduction of mine-run-rock required for conveyor application. Four years after the initial mobile crusher installation, the first report published on the subject appeared in the December 1960 issue of Mining Engineer (Kochanowsky, 1960). With this early background and basis for direction, mobile in-pit crushing and conveying have increased to more than 74 installations. The capacity, type of crusher, and material being processed appear in Table 1. These data in Table 1 indicate that experience to data has been heavily influenced by limestone installations of less than 1 kt/h (1102 stph). Most of these installations were directly fed by a mine face excavator because of the limestone quarry ground conditions. Crusher Configurations Crushers systems developed to date have varying mobility capabilities. These range from fully mobile units that are used continuously in this mode to fixed, permanently located in-pit crushers. The following terms are presented to help distinguish the range of mobility within the configurations of "mobile" crusher systems planned or now in use. Mobile Crusher The crusher works at the mine face, is directly fed by an excavator, and moves in unison with the excavator on its own transport mechanism as the mining progresses. An example is the unit delivered in 1976 to Yamama Cement Co. in Reyadh, Saudi Arabia.

Jan 1, 1986

By W. T. Hicks

The oxidation of CbO was studied by a gravimetric technique from 400° to 1200°C in oxygen. In this temperature range the oxidatiotz is characterized by an irlductive period of low oxidation rate, which becomes shorter as the temperature increases, followed by a rapid parabolic oxidation. The oxidation of CbO cannot be rate controlling in the oxidation of Cb metal in the temperature range, 800° to 1200°C. A thin optically inactive layer has been observed between the metal and Cb2O5 layer of Cb oxidized at 700°C or higher temperatures. Figs. 1(a) and 1(b) show the edge of a sample of Cb reacted to 50 pct of complete oxidation at 800°C. Fig. l(a) taken under bright field illumination shows a layer of oxide adhering to the unoxidized metal core. Fig l(b) taken under polarized light shows that this oxide layer is

Jan 1, 1962

By Persifor Frazer

The '(author's edition" of the following paper, "subject to re vision," was received by him, and copies sent to Professor Geikie and others about two weeks before the date of the meeting at which it was to be read. A telegram, and subsequently a letter (both of which unfortunately arrived too late), apprised the present writer that the Director General objected to certain views ascribed to him as the reverse of those which he really held. These views, however interesting, had no very important bearing on the object of the fol lowing notes, which, as must be evident, are devoted to the conside ration of the close analogies between the Welsh and American rocks. Without being able, therefore, to account for the circumstance which Professor Geikie has mentioned, it is thought better in the present revised edition to omit all allusion to Professor Geikie, or Mr. Peach, or their views, except in this place, where I desire to thank them for their courtesy during the time which I had the pleasure of spending in their society. It appears sufficiently throughout the body of the paper that the writer had not the slightest intention of entering the controversy, which was about to commence, concerning the proper horizons of the St. David's rocks, for many reasons; and amongst others because he did not feel that a sojourn of a few days in a difficult region, which had been already studied by many of the foremost geologists of England, would warrant him in adding to the literature on the sub ject. The discussion of the analogies between these rocks and those of the Eastern Appalachians, which he has studied for twelve years, of which eight were spent in the service of the Second Geological Survey of Pennsylvania, was much more to his taste as it was more within his ability, and if he has added anything to the evidence of these analogies, the paper, however imperfect, will not have been written entirely in vain. Right or wrong, he assumes the entire responsibility of what follows.

Jan 1, 1883

By E. Buehler, E. Berry

HE magnetic properties of dilute palladium alloys are of fundamental interest.''' Neutron diffraction studies3 have indicated that a better understanding of the behavior of these alloys could be realized with the availability of high-purity single crystals of palladium. Crucible melts of 99.999 pct pure palladium were found inadequate for such research. In a successful effort to fill this need, floating zone refining of palladium was undertaken. In this note the results of the initial experiments are reported. Zoning was accomplished in an argon atmosphere using 450 kc rf generator for an energy source. Samples 5 to 6 mm in diam were suspended in a gastight quartz envelope which could be moved vertically through the rf coil. A nominal upward traverse rate of 1.5 mm per min was maintained during a pass. Close coupling was found to be essential for stable retention of the liquid in the zone. Single crystals averaging 3.5 cm in length were obtained. Laue photography showed them to be continuous single crystals without gross imperfections. Several criteria were used for evaluation of the purity of the zoned material: magnetic behavior, low-temperature specific heat and residual resistivity ratios. Table I shows the residual resistance ratios obtained for two samples, one subjected to a single pass, the other zoned four times. It is appilrent that palladium can be zone refined with the electrically active impurities being transported toward the tail end. A decrease in susceptibility for zone-melted specimens over any previously measured material from 1.5" to 80'~ has been obserted by H. J. Williams and R. C. Sherwood4 substantiating the residual resistance data. The specific heat measurements are currently being made3 and will be published at some later date. Discussions with J. H. Wernick and S. C. Abrahams are acknowledged. We also wish to thank G. F. Brennert for the residual resistance measure ments.

Jan 1, 1962

[*DAVID THOMAB ...................... 1871 *R. W. RAYMOND .1872-1874 *A. L. HOLLEY ....................... 1876 *Asurn 8. H~WITT ................... 1876 *T.ST~RYHUNT ..................... 1877 *ECKLBY B. COXB .1878-1879 *WILLIAM P. BHINN .................. 1880]

Jan 1, 1946

By H. W. Weart, S. Sarian

The effect of temperature, impurities, and capillarity on the morphology of solid particles in a liquid matrix is investigated. For the NbC-liquid iron system, at least, it is found that those particles which are dissolving will assume a spherical shape; all others will take the equilibrium shape. An aniso-tropic-isotropic transition in the interfacial tension is observed at about 1725°C and is believed to be due to cooperative roughening of the interface on an atomic scale. The presence of boron as an impurity lowers the transition temperature. It is the purpose of this paper to present some observations on the shape of particles in a system consisting of solid particles of nonuniform size in a liquid matrix and to propose an explanation for these observations. Although qualitative only, these observations, which were made largely in the course of a study of particle-growth kinetics,' are presented separately to draw attention to them. They reveal the effect of particle size, temperature, and surface-active impurities on particle shape in the solid NbC-liquid iron system, and are unique in demonstrating for the first time the reversible effect of temperature and impurity concentration on the anisotropy of the energy of the solid-liquid interfaces involved. Some of the changes are readily demonstrated with the few particles whose shapes can be clearly shown in a single photomicrograph, but others are more subtle, and their recognition depends upon some experience and the study of a much larger sample. For this reason, a certain amount of judgment must be acknowledged to underlie their detection, but every effort was made to maintain proper scientific objectivity in evaluating the observations. The observations will be presented first, and then an explanation rationalizing them will be offered. Brief reminders of the relevant theories will be inserted into the discussion at the appropriate points. EXPERIMENTAL The observations were made of the shape of NbC particles dispersed in liquid iron. All specimens were prepared by pressing NbC powder and car- bony1 iron powder treated according to standard powder-metallurgical procedures. Except as noted, all specimens were heated to 1900°C for 1/2 hr. In investigating the effect of temperature, specimens were quenched from 1900°C to various lower temperatures, and held long enough (48 hr) to allow shape changes to be completed. Boron, in the form of amorphous powder, and oxygen, in the form of niobium oxide powder, were added as impurities to some specimens. Nitrogen was introduced into some specimens as an impurity by heat treating the samples under a partial pressure of nitrogen gas. Effect of Temperature. It was first observed that increasing temperature had a marked effect in rounding the corners and edges of the particles. At 1900°C the particles are all very nearly spherical and remain so even when the holding time is extended to 48 hr. As can be seen from Fig. 1, there is virtually no evidence of the presence of low-index planes. At 1300°C, however, most of the particles are prismatic with very slightly rounded edges and corners, Fig. 2. (In making these shape comparisons, attention should be focused on the larger particles, even though the smaller ones would be expected to be the first to change shape, owing to the shorter diffusion distances involved. The cause of the mixed particle shape will be explored later.) It was established that these structures are re-

Jan 1, 1965

By Will Coghill

FLOTATION has been so closely allied with the sulfide minerals and their early and associated oily reagents that the term "oil flotation" has erroneously been applied to the entire flotation process. Today, the term "chemical flotation" might be used to advantage. Flotation literature has dealt primarily with the removal of sulfides from non-sulfide gangues, and the separation of one sulfide from another. Now, the application of the process to the separation of nonsulfide minerals is coming to the fore; and from the standpoint of the number of commercial minerals involved, the flotation of nonsulfides offers the larger field. Here, soap or soap-forming substances, such as the fatty acids and their derivatives, are used; hence there may well be a subdivision of the chemical flotation process called "soap flotation." Early experimenters learned that it was easy to form a froth or foam that would carry a part or all of the ore charge over the lip of the flotation machine; but this could not be regarded as flotation because of the lack of selectivity. Doubtless soap was one of the first reagents tried, and doubtless it was rejected on account of its gangue-carrying properties. Now this same gangue-carrying ability makes soap an acceptable reagent, for we are dealing with that, which among sulfides, is considered "gan-gue." As in the flotation of sulfides, so in the flotation of nonsulfides, the selective flocculation of the mineral and the dispersion of the gangue are the first objectives. In fact, these two phenomena epitomize flotation. They depend upon the unlike surface properties of the respective miner-als; and as long as the components of an ore have unlike surface proper-ties, a separation is possible, at least in theory. Often in nonsulfide flotation it makes little difference which mineral floats and which is depressed; generally only a separation is sought.

Jan 1, 1932

By William C. Brice

Minnesota is involved in planning controversies related to taconite and potential copper-nickel mining. Mine facility planning includes the Reserve dining on-land tailings disposal issue and the potential for a new copper-nickel mining district. Both provide a unique opportunity for innovative planning in the attempt to be responsive to public and private interests. Concerns that emanate as a result of mineral resource activities include environmental protection, land use competition, land exchanges, highway and utility extensions, and legal constraints on public or private lands. The purpose of this newly-developed planning approach is to anticipate such issues and provide a rational information base for dealing with them. The result will be a framework plan for guiding public planning, and an impact assessment for reviewing the implications of industrial project proposals. The approach uses a computer-stored resource inventory of natural and cultural information. Geographic data is mapped and entered into a computer storage and retrieval system. This enables systematic analysis of mineral resources along with environmental and land use considerations. Computer mapping describes the relationship of each activity and allows identification of potential conflicts; it also shows geographical extent in the form of statistical compilations. Resource data is being collected and compiled using a standard metric grid (Universal Transverse Mercator). Individual cells are 100 m. squares and represent areas of about 2.5 acres. The study area contains about 145,000 cells. Data inventories are being compiled in 25 natural and cultural resource categories. Geologic variables include Bedrock Geology, Taconite Reserves and Potential Resources, Depth to the Duluth Complex Contact and two soil inventories. Topographic and hydrologic variables include elevation, slope, slope orientation, surface hydrology, and watersheds. There are also 6 biological data variables and 7 land use inventories.

Jan 1, 1977

By T. Egleston

SOME months ago samples of black oxide of copper and of pig copper from Colorado were sent to me to examine for arsenic and

Jan 1, 1882

By Robert A. Colten, Frederick C. Hull, Robert F. Mehl

It is known that pearlite forms from austenite by a process of nucleation and growth, and that the rate of formation of pearlite may be described by a rate of nucleation and a rate of growth.l,2 The manner in which these two quantities operate to produce the observed isothermal reaction curve has been analyzed in a paper published in I939.3 Two types of process were described: (I) that in which nucleation occurs at the grain boundaries of the parent phase, with the nodules growing toward the centers of the grains, initially as hemispheres and then after impingement as roughly radial-columnar structures; and (2) that in which nucleation occurs generally, with the nodules growing to full spheres until impingement with other growing nodules restricts growth. Both cases are met in the formation of pearlite from austenite (Fig. I);2,4 the former, occurring near the knee of the S-curve, has been named "grain-boundary transformation," and the latter, occurring at temperatures near Ael, has been named "group-nodule transformation." In developing our knowledge of the factors that determine the rate of formation of pearlite from austenite, it is important1,2 to obtain data on the rate of nucleation and the rate of growth of pearlite. Such data, when obtained near the knee of the S-curve, will furnish information of use in understanding the factors that affect hardenabil-ity; when obtained at higher temperatures, such data will be useful in understanding the behavior of steels that during heat-treatment react to pearlite.2 It is the purpose of this paper to present data on the rate of nucleation and the rate of growth of pearlite in dependence upon composition, grain size, temperature, and the degree of homogeneity of the parent austenite. The studies are restricted chiefly to plain carbon commercial steels." Previous Data on Rate of nucleation and rate of Growth Data on the rate of nucleation and the rate of growth of pearlite have been published by Scheil and Lange-Weise,5 by Mirkin and Blanter,6,7 by Meh1,l and by Dorn, De Garmo and Flanigan.2, It is difficult to interpret the data, for in most cases too little information is given on austenitizing temperatures and times, the state of homogeneity of the austenite (presence or absence of carbide, etc.), austenite grain size, and mode of formation of pearlite at the temperatures given. Except for the approximations of Mehl and the work of Dorn, austenite grain size was disregarded, though it is well known

Jan 1, 1942

By Louise Reber

THE town of Jerome is located in Yavapai County in north central Arizona. It has a population of over 6000 people and the two important mines of the district, the United Verde and the United Verde Extension, lie almost within its limits. Perched high on the southwest side of the Verde Valley, at elevations of 4800 and 5500 ft.. (1463 and 1676 m.), both mines have long tunnels from their lower levels through which ore is hauled to their respective smelters. The two smelter towns of Clarkdale and Verde, out in. the center of the valley and about 2000 ft. (609 m.) below, form part of the wide panorama that meets the eye at Jerome. This panorama and the topographic and surface features and the geologic formations are shown in a separate pamphlet. In the vicinity of Jerome, the great southern escarpment of the Arizona plateau forms the northeast side of the Verde valley. The general level of this escarpment, or "the rim" as it is called, is about 4000 ft. above the Verde River. A corresponding elevation is reached only by the, highest parts of the Black Hills, which bound the valley to the southwest. The two lava-capped mesas, known as Mingus and Woodschute Mountains, form the culmination of the Black Hills. That part of the old Black Hills mining district which lies between their crests -and the Verde River is now known as the Jerome or Verde copper district. However, if the smelters are not included, a strip about 7 mi. long and 3 mi. wide (11 by 5 km.) embraces practically all the properties belonging to the Jerome district. This strip lies parallel to and along the side of the Verde valley from about First View, 2 mi. northwest of Jerome, to the neighborhood of Allen Spring, near the south end of Mingus. Mountain. The rank of the district in copper production, as well as features of peculiar geologic interest in connection with the ore occurrences, entitle the district to much more consideration than it has received in the literature of copper mining. Arizona stands preeminent as a copper-producing state. In 1918, it produced four-tenths of the total amount produced in the United States, and nearly equaled the, combined production of its three chief competitors, Montana, Michigan, and Utah. The production of the Jerome district places it in the sixth place among the copper

Jan 8, 1920

By C. K. Leith

The question as to what grades of ore it pays to conserve for the future, and the valuation of low-grade reserves, are becoming immediate and definite as applied to the individual ore deposits, and seems to call for some sort of quantitative answer.

Jan 1, 1915

Organization Place Date 1917 American Institute of Architects Philadelphia., Pa. Dec. 26-29 American Society of Mechanical Engineers New York City. Dec. 4-7 American Mining Congress State Chapter Phoenix, Ariz. Dec. 26-29 1918 American Society of Civil Engineers New York, N. Y. Jan. 22-25 American Institute of Mining Engineers New York, N. Y. Feb. 18-21

Jan 12, 1917

Jan 1, 1935

By A. E. Back, S. F. Ravitz

When manganese ores are leached with sulphur dioxide, a large part of any zinc in the ore usually is extracted with the manganese.1 In the dithionate process,2,3 in which the manganese ore is leached with dilute sulphur dioxide gas and the manganese is subsequently precipitated by adding lime to the pregnant solution, the zinc is precipitated with the manganese. These facts suggested the possibility of applying the dithionate process to the recovery of zinc from oxidized ores or calcined sulphide concentrates. Accordingly, an investigation was begun, and preliminary tests were made on several ores and concentrates. The results were encouraging, but the need to devote available funds and personnel to other projects made it necessary to drop the work before the various factors involved in the process could be studied in detail. A brief mention of the process,4 however, elicited a number of inquiries, so that it appeared desirable to report the results of the preliminary work. The dithionate process as applied to zinc may be summarized briefly as follows: The ore or calcined concentrate is leached with dilute SO2 gas to dissolve the zinc, largely as zinc sulphate, in accordance with the following equation in which [ZnO] represents the "oxide zinc" in the ore or calcine: [ZnO] + SO2(g) + 1/2 O2 = Zn++SO4— [1] If, in the leaching step, the ore or calcine is suspended in calcium dithionate solution, the sulphate ion, as it is formed, is precipitated immediately as calcium sulphate, which is subsequently filtered off with the insoluble ore residue: Zn++SO4— + Ca++S2O6— = CaSO4(s) + Zn++S2O6- [2] An alternative procedure is to suspend the ore in water, filter off the insoluble ore residue after leaching, add calcium dithionate to the resulting zinc sulphate solution, and then filter off the calcium sulphate precipitate. In either event the zinc is obtained in the form of a pregnant solution of zinc dithionate, from which it can be precipitated as relatively pure zinc hydroxide by adding milk of lime: Zn++S2O6— + Ca(OH), = Zn(OH)2(s) + Ca++S2O6- [3] The zinc hydroxide precipitate is calcined to form the final zinc oxide product: Zn(OH)2 = ZnO(s) + H2O(g) [4] Theoretically the process is completely cyclic with respect to dithionate ion, the calcium dithionate required for reaction 2 being replaced by that formed in reaction 3. In practice, of course, small amounts of dithionate would be lost in the various filter cakes, depending on the economic washing limits. In the leaching step, however, some of the SO2 is oxidized to dithionale instead of sulphate, accord- ing to the following overall reaction: ZnO + 2SO2(g) + 1/2 O2(g) = Zn++S2O6-, [5] so that the dithionate losses are made up, at least in part. Ores and Concentrates Tested The analyses of the ores and concentrates tested are summarized in Table 1, which also includes the analyses of the calcines produced from the concentrates. The concentrates were roasted in a laboratory muffle furnace at the temperatures indicated until evolution of SO2 could no longer be detected; shallow clay dishes ordinarily were used; but calcines 2a and 2c were prepared in iron dishes, with the result that these two calcines were badly contaminated with iron scale. The "complex" concentrate, sample 1, consisted essentially of sphalerite grains containing inclusions of pyrite and other sulphide minerals too minute to be liberated by grinding within economic limits. In the " marmatitic" concentrate, sample 2, the iron was present largely as marmatite (that is, as iron sulphide in solid solution in zinc sulphide) rather than as pyrite inclusions. The zinc was present largely as the carbonate in the two "oxidized" ores, samples 3 and 4, and as the silicate in the "willemite" ore, sample 5. Leaching Tests The leaching cell was a 3-liter glass beaker placed in an electrically heated water bath manually controlled to maintain a temperature of 35°C in the leach slurry. The slurry was agitated by means of a flat paddle-type stirrer

Jan 1, 1950