Search Documents

By M. Garfinkle

LITERATURE data1'3 have suggested that the resolved shear stress necessary to initiate slip in a particular slip system in tungsten single crystals is strongly dependent on the tensile orientation of the crystals. This orientation dependence is contrary to the critical resolved shear stress criterion. Because the Schmid factors for slip on particular {110}( I l l), {112}(Ill), or {123}(111) slip systems in a (100) oriented tungsten crystal are virtually identical to the respective Schmid factors for a (110) oriented crystal, slip should initiate on the same system in both orientations, independent of the values of the critical resolved shear stresses. Thus, it would be expected that, for a critical resolved shear stress model to hold, the proportional-limit stress for these two orientations must be similar. The expectation of similar proportional -limit stresses has not been borne out by reported experimental observations. Rose et nl.' reported that the proportional-limit stress for crystals near the (110) orientation was 92,000 psi, approximately three times that of (100) oriented crystals (31,000 psi). Garlick and probst2 reported greater than a fourfold difference. Most recently, Beardmore and ~ull~ examined tungsten crystals with orientations along the edge of the standard stereographic triangle and showed a gradual increase in proportional-limit stress from 28,000 psi for the (100) orientation to 93,000 psi for the (110) orientation. Again, the difference was more than threefold. As has been emphasized by these investigators, the apparent gross variation of proportional-limit stress with orientation precludes any meaningful analysis of slip mechanics using a simple critical resolved shear stress relation. The purpose of the present communication is to report that, by use of refined strain-measuring techniques, the proportional-limit stresses for the (100) and (110) orientations are quite similar. Obviously, to determine accurately the value of the proportional-limit stress, which is by definition the stress at which nonlinear stress-strain behavior first occurs, the method of measuring strain must be capable of high accuracy. The investigators cited used as the measured elongation the crosshead displacement of the tensile machine. This method, however, introduces extraneous strain contributions from the load train. Because these extraneous contributions are considerable in the initial portions of loading (as has been well-documented in the literature) the proportional-limit stress measurement, dependent on the deviation of a line from linearity, can be significantly affected. During the course of a recent study, room-temperature strain was measured directly on several (100)-and (110)-oriented tensile specimens axially oriented within 5 deg of the desired direction. Each specimen was fitted with two foil strain gages mounted on opposite sides of the 0.08-in.-diam reduced section. The tensile specimens were loaded at a crosshead speed of 0.01 in. per min on an Instron Universal Testing Machine. Strain was monitored through an external bridge circuit in which the specimen strain gages comprised two arms. The bridge output was recorded against the applied load. A strain of 2 x 10"" could be readily detected by this method. Some specimens were subjected to conventional loading while the load for others was cycled between zero and continually increasing values until the first deviation from linearity was observed. The results of these methods were similar, and the stress at which nonlinear behavior occurred was considered the proportional-limit stress. The proportional-limit stresses measured in this study are approximately 5000 and 6500 psi for the ( 100) - and ( 110) -oriented crystals, respectively, a range of values almost a magnitude less than those reported previously. Representative curves are presented in Fig. 1. Because of the nature of the measurements made, the point of departure of a line from linearity is often debatable. While the load-strain curve for the (100) -oriented crystals made a relatively abrupt deviation from linearity, the curve for the (110) -oriented crystal was more gradual, so that the actual point of tangency may be at a lower load than reported. Thus, the difference in values for the proportional-

Jan 1, 1967

By Thomas T., Read

E DUCATION for the mineral industry was at first a single comprehensive curriculum, but it was early recognized that the main basis of mining is physics, while that of metallurgy is chemistry. The first school to offer curricula leading to degrees in mineral industry education in the United States (1853) had separate ones in mining and metallurgy. The Columbia School of Mines (the first really successful one) had only a single curriculum when it opened in 1864, but within a few years had so reorganized its work that it offered curricula in mining, metallurgy, geology, chemistry, and civil engineering. Interest in the metallurgy or geology curricula was slight at first, and for the next 30 years the great majority of Columbia students took the mining curriculum, probably partly because it contained nearly as much geology as the geology curriculum, practically all the metallurgy, and most of the chemistry, and partly because of the degree awarded for it. Other schools kept their mining curricula equally broad, and as late as 1900-1910 men were graduating as mining engineers who were practically as well prepared to make geology or metallurgy their life work, as they were for mining. Gradually, however, the subject matter of mining geology and metallurgy became so enriched through research and development that separate curricula in them became worth while; their progressive development is the subject of another chapter. Mining curricula also began to be somewhat diversified, and schools in areas where coal mining was of outstanding importance began to offer options in coal mining, the earlier curricula having been chiefly aimed at metal mining. The petroleum industry began its meteoric rise about the same time as mineral instruction in this country, but little more of applied science attended its birth than had attended such ancient practical arts as copper and iron

Jan 1, 1941

By Terkel Rosenqvist

Few subjects in iron metallurgy and steelmaking have caused so much discussion and have resulted in so many divergent and partly contradictory statements as the theory of the distribution of sulphur between molten iron and slag. An interesting survey of the different points of view is given by Grant and Chipman.1 Grant and Chipman themselves conclude in their paper that, at least in the open hearth and electric steel furnaces, the governing reaction is a simple distribution like: FeS steel ? FeS alas [Ia] and MnS steel ? MnS alas [Ib] They conclude that no significant reaction takes place according to the more classical scheme: FeS steel + CaO slag ? FeOslag + CaS slag [2a] This is the reaction which is regarded by most investigators as the primary sulphur reaction in the blast furnaces, where it is accompanied by the reaction with carbon: FeO slag + C ? Fe + CO [2b] The writer suggests an alternative to the reactions mentioned above. It is the opinion of the writer that the a priori assumption of defined molecular compounds being present in molten steel as well as in molten slag, has retarded rather than promoted a solution of the sulphur problem. As for the constituents of molten steel, it is taking too much for granted to mention the presence of FeS and MnS. If this infers that the melt contains diatomic molecules, the statement must be made that at least such molecules do not exist in the solid state at room temperature. Solid FeS crystallizes in the nickel-arsenide structure, and MnS (high temperature form) in the sodium-chloride structure. In these structures the sulphur is surrounded by six metal neighbors, and no molecular groups can be isolated. When sulphur is dissolved in molten steel, it is expected to maintain the same coordination number as in the solid state. We know that sulphur in steel has a certain chemical potential and a chemical activity which can be expressed by the reaction: S steel + H2 ? H2S where the activity A. is proportional to the ratio PH2S/Ph2. We know also that this activity is influenced by the presence of other constituents. For instance, there is reason to assume that carbon and silicon increase the sulphur activity and manganese decreases it. However, the exact relationship here is scarcely known, and further investigations are needed. Concerning the molten slags, if anything should be assumed a priori it would be that they are composed of ionic rather than molecular parts. There are indications of this in that solid silicates form ionic structures, and molten slags show high electric conductivity and can be electrolyzed.2 It has been claimed by Taylor and Chipman3 that their activity investigations

Jan 1, 1949

By C. H. Stein

The Pennsylvania Legislature, on March 13, 1837, passed an act authorizing the Lehigh Coal & Navigation Co. to construct a railway to connect the North Branch Division of the Pennsylvania Canal with the slack water navigation of the Lehigh River; the navigation company accepted this act on May 10, 1837. Edwin A. Douglas, chief engineer for the navigation company, located the route for this railway from White Haven to Wilkes-Barre, which was called the Lehigh & Susquehanna Railroad. The object was to transport coal from the Wyoming Valley, of Pennsylvania, to the Atlantic seaboard. This railway was considered a marvelous piece of engineering, as it included a tunnel nearly 55 mi. long, and a series of inclines, or planes, up which the cars laden with coal were raised from the vicinity of Ashley to the summit of the mountain near Solomon's Gap, whence they were taken to White Haven by rail. There the coal was transferred to canal boats. In June, 1862, floods almost completely destroyed the upper division of the canal, so on March 4, 1863, the Pennsylvania Legislature passed an act prohibiting its restoration, but granted a charter for the construction of a railway from White Haven to Mauch Chunk to connect with the line from White Haven to Wilkes-Barre, previously built. On March 16, 1864, a supplementary act was passed extending the Lehigh & Susquehanna Railroad to Easton, Pa. This completed a direct all-rail route from Wilkes-Barre to the New York harbor (by way of the Central Railroad of New Jersey). Up to this time, all freight and passenger traffic passed over the planes, but in 1866 and 1867 there was constructed what was known as the "back track" down the mountain side between Solomon's Gap and Ashley over which all the passenger traffic and empty cars thereafter passed; it is now known as part of the main line. For the handling of the heavy coal traffic, however, this would have involved a continuous climb from Ashley, 170.27 mi., from New York, to Solomon's Gap, 157.8 mi. from New York, or a distance of 12.47 mi., and a total ascent of 1013.75 ft., composed of grades 95.61, 83, and 51.4 ft. per mi., respectively, and

Jan 1, 1922

By Joseph Pogue

PRORATION in the petroleum industry has come to mean a method for curtailing the production of crude petroleum by artificial effort, and it is in this sense that the term is employed throughout this paper. Although a contrived curb on supply has been invoked at various times in the past in particular fields and to meet specific situations, it is not until the past few years that this procedure has become general and assumed a dominant role in the oil business. In the sense that we now understand it, proration had its inception in the Seminole area of Okla-homa in 1927, from which time and place the practice spread to include practically all the flush oil fields of the country, especially those of California, Kansas, Oklahoma and Texas. At present there is perhaps no phase of the oil business that commands more attention than proration, nor one that engages more time and effort on the part of executives in the business. The practice of proration, indeed, has not only become an integral part of the policy of most companies and operators, but it has also taken on the aspects of a "movement" involving two schools of thought with considerable feeling, and at times some bitterness, on both sides. In this atmosphere it is difficult to find calm, dispassionate consideration of proration, for most discussions are either vigorous exhortations by its proponents, or else sharp condemnations by its opponents; although it appears that the majority of the industry is clearly "in favor of" proration. It is hoped that this analysis will be taken as an attempt to appraise the movement as an economic force, without bias and without regard to the incidence of the conclusions upon any preconceptions that the industry may entertain.

Jan 1, 1932

By Henry M. Howe

Jan 1, 1908

By C. C. Furnas

IT is well known that particles of different sizes are not distributed evenly throughout the average charge in an iron blast furnace. Just how great the disparity in particle size in different parts of a single plane in a furnace may be is indicated by the results of some recent investigations1 conducted by the Bureau of Mines on a furnace operating on Lake ores. The wide variations found in gas velocity, gas composition, and temperature from the periphery to the center of the upper charge column were caused by the great variation in particle size of the raw materials used and were also greatly influenced by the methods of charging. This paper summarizes the results of an investigation of the influence of different methods of charging and of the treatment of raw materials upon the size distribution of the solid particles in the blast furnace. A more complete report will appear later as a Bureau of Mines technical paper.

Jan 1, 1929

By Charles Austin

IT has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent C0 and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their pro-portional limits and yield points are rela-tively low. Published data1 for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the results shown in the lower section of Fig. I. TABLE I.-Analysis of Material I Percentages Constituent Sample Sample Sample 3125 3124 3123 Si 0.25 0.51 o.6o Fe 4.15 10.70 13.17 Ti I.15 3.58 4.70 Mn 0.30 0.41 0.42 Co (by difference)^ 94.15 84.80 81.71 The cobalt from all three samples, united and tested for nickel, gave 0.54 per cent Ni based on the weight of cobalt. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deforma- tion characteristics in moderately long-time tests at 600°, 700° and 800°C. after quenching from various solution tempera-tures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain in- FIG. 1.-EFFECT OF VARYING AMOUNTS OF FERROTITANIUM (FE2TI) ON PHYSICAL PROPER-TIES OF COMMERCIAL COBALT. (C. R. Austin.1) Upper section. Tested at 600°C. after water-quenching from 950°C. Lower section. Tested at 600°C. after water-quenching from 950°C. and aging 72 hr. at 650°C. FIG. 2.-PORTION OF QUASI-BINARY DIAGRAM COBALT-FE2TI AS DETERMINED METALLOGRAPH-ICALLY. formation on the quasi-binary system Cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufac-turing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table I. The alloys, when originally made up,1 were based upon an iron-titanium com-pound, Fe3Ti, as indicated by the work of

Jan 1, 1940

By Frank Julian

After the solution of an iron ore, or metallic iron, in an acid, for the determination of phosphorus, it is necessary to evaporate the solution to dryness and to heat the residue to effect the complete separation of silica. Authorities differ as to the temperature required, some recormmentling not over 100' C., others as high as dull redness. For the purpose of securing some indications as to the degree of heat which may be safely or advantageously employed, I selected a gray pig-iron, a piece of Bessemer steel rail, and a sample of Ludington ore having the following composition; the phosphorus in the pig and steel being determined by Giutl's ferric chloride method:

Jan 1, 1884

To Install Waste Heat Boiler at White Pine White Pine Copper Co.'s smelter 18 miles southwest of Ontonagon, Mich., will have a six story high boiler utilizing what otherwise would be waste heat from a copper reverberatory furnace. Designed and under construction by the Babcock & Wilcox Co., the boiler will supply steam to a turbo-generator furnishing power for the projected development. The boiler will be in line with and following the reverberatory furnace. Using waste heat from the furnace in place of fuel for steam generation, about 50 pct of heat in the fuel originally supplied to the furnace will be recovered by the waste heat boiler. Exploration conducted over the past 15 years at White Pine, wholly owned subsidiary of Copper Range Co., has disclosed reserves of 309 million tons averaging 21.3 lb of copper per ton. Ore mineral is chiefly chalcocite (Cu2s).

Jan 5, 1953

By H. I. Young

Inasmuch as there has been a great deal of activity in this district recently, a paper of this kind should treat of all the various phases of mining, namely, prospecting, developing, and operating. Prospecting .. Where ore is found at a depth of 100 ft. (30 m.) or more, the prospect work is done by churn drilling. Several makes of churn drills are used in this work, both steam- and gasoline-driven machines being used. The drilling is usually started with a 6-in. bit, and the size of the bit is reduced, if necessary, as the hole is advanced. It is general practice to drill from 100- to 400-ft. holes, but this is governed entirely by the location and formation of the ground. In drilling sheet ground, close spacing of drill holes is unnecessary, but in narrow orebodies, the holes are spaced from 15 to 50 ft. (4.6 to 15 m.) apart. Ten years ago, very few assays were kept of the drilling, but during recent years records have been kept very accurately, showing the location, elevation, assays, and also the vertical section of the hole. After the orebody is reached, cuttings are taken every 2 or 3 ft. (0.6 to 0.9 m.) samples being sometimes taken by pouring the water off the cuttings and taking a portion of the coarse material for assay. It has been found, however, that very often the sludge material poured off with the water contains high mineral values. To overcome this, cuttings from each 2 or 3 ft. are put in a container, and, after the water is evaporated, sample for assay is taken by means of Jones samplers. Permanent records of cuttings showing various formations are kept in glass jars or glued on large cards. Drilling at present is costing from $1.25 to $1.50 per foot. In pre-war times, the drilling costs ran from 75c. to $1 per foot. Development After proving property by drilling, shafts are put down to the ore-body. These are usually vertical shafts, either single or double compart-

Jan 1, 1918

Exploration by AS&R of the Nuestra Senora lead-zinc-silver property, located in Cosala District, Sinaloa, Mexico, has proved sufficient ore to warrant placing the mine on an operating basis. Installation of mine plant, concentrator, and townsite, is expected to commence late in 1951. Opening of a lead-zinc property in Nigeria is also being contemplated by AS&R. Private enterprise is being urged by Secretary of Interior Chapman to start a synthetic fuels industry, it is reported. Based on tests at the Louisiana, Mo., plant which produces quality gasoline at costs up to 144 per gal, he predicts that a commercial plant would pay for itself in 10 years.

Jan 4, 1951

By O. H. Eschholz

THE electrostatic process of fume precipitation is an excellent example of the successful application of scientific knowledge to an industrial operation. Originally proposed for the precipitation of sulphuric acid mists, it has been extended until at present there is practically no fume carrying gas to which the method cannot be applied. Among the more common applications are: the recovery of non-ferrous smelter flue-dust, iron blast-furnace dust, cement dust, and potash fume. It should be borne in mind that the process is restricted to the precipitation of suspended particles, either liquid or solid, and does not separate gaseous constituents. However, -by proper temperature control, mixtures of vapors having different temperatures of condensation to either solids or liquids may he selectively precipitated. The process consists essentially of subjecting suspended particles, including those too minute to be effectively acted upon by centrifugal or gravitational forces, to such an electrical force that they are driven from the gas stream, acting as a conveyer, and deposited upon a suitable receiving surface. This directional impulse is obtained front the interaction of charged particles and an electrostatic field of definite intensity gradient existing between two dissimilar electrodes, known as discharge and receiving electrodes. In principle, the equipment is equally simple. As shown diagrammatically in Fig. 1, it consists of: (1) A source of high-potential direct current, requiring: (a.) Source of alternating-current energy. (b) Means of transforming from tow voltage to high voltage. (c) Means of converting alternating to direct current. (2) Precipitation chamber having: (a) Transmission tubes for fume-laden gases. (b) Suitably designed and disposed electrodes. (c) Means for affecting removal of deposited solids.

Jan 8, 1918

By Robert F. Mehl

THE gamma-alpha transformation in iron and iron-rich alloys is of such practical and theoretical importance that many papers have been published upon the subject relating to critical temperatures, transforma-tion rates and accompanying property changes. Although crystallo-graphic studies are of less immediate practical usefulness, the opportunities which these offer to furnish data, on the basic atomic movements which characterize the transformation are not to be neglected1. The early work on the crystallography of this transformation has been reviewed in the fourth paper of this series2 since then several important papers have appeared. Our present, knowledge may be briefly summarized as follows. Kurdjumow and Sachs, working with a 1.4 per cent carbon steel3, established the orientation relationships subsisting between the face-cen-tered gamma and the metastable tetragonal lattices in freshly quenched martensite, and between the face-centered gamma and the body-Centered alpha lattices in tampered martensite. The orientation relationship observed in the latter case may be stated in terms of planes and directions observed to lie parallel in the two lattices: { 111 }Y//{110}a [110]Y//[111]a

Jan 1, 1937

By J. Burbank

A TECHNIQUE has been developed for the microscopic study of the three-dimensional structure of the Pb-Sb alloys by the formation of a chemical replica in which the internal structure of the metal may be seen directly. In the replica process one of the phases present in the structure as-cast is converted into a translucent material, and the second phase remains virtually unaffected, permitting microscopic examination by transmitted light. Alloys of lead and antimony were made from the chemically pure metals, cast in a sooted and pre-

Jan 1, 1954

By H. C. Stumpf, L. A. Willey, V. L. Fink

Very few studies of the aluminum-sodium system have been reported. Heycock and Neville1 were unable to detect any solubility of sodium in liquid aluminum. Mathewson2 prepared an equilibrium diagram consisting of two horizontal lines at the melting points of the two metals. He was unable to detect solubility at either end of the system. Scheuer3 first developed a method for the chemical determination of sodium in aluminum and then studied the solubility of sodium in liquid aluminum. His method involved heating aluminum with excess sodium under hydrogen until the two liquids were at equilibrium, chilling the melt, and analyzing the aluminum-rich layer. He reported the solubility to be 0.10 pct sodium at 700°C, 0.115 pct at 750°C, and 0.128 pct at 800°C. This paper on the aluminum-sodium system is the twenty-first in a series from the Aluminum Research Laboratories describing equilibrium relations in aluminum alloy systems. Materials The alloys for this investigation were prepared from electrolytically refined aluminum (99.99 pct) and sodium of reagent quality conforming to specifications of the American Chemical Society. Chemical analysis of the aluminum showed the fol- lowing impurities: 0.002 pct Si, 0.002 pct Fe, 0.002 pct Cu, <0.001 pct Mn, 0.002 pct Mg and 0.001 pct Na. The sodium content of all alloys was determined by either chemical or spectro-graphic standard procedures5 No. IIA and No. SI I respectively. Determination of Miscibilitv The boundary of the miscibility gap was determined by a modification of the method of Scheuer3 and of that used by Henry and Cordiano. As finally developed the method was as follows: A fused alumina crucible 25 mm id with 75 mm depth and 1.5 mm wall thickness was placed on the bottom of a container made from a 4-in. length of 1 1/2-in. iron pipe and pipe caps. ?&apos;he space around the sides of the crucible was filled with 40 mesh crystalline alun-dum. A charge of 60 g of aluminum and 10 to 15 g of sodium was placed in the crucible, the sodium first being trimmed and rinsed with iso-pentane to remove kerosene. The container was tightly capped, filled with argon (99.6 pct pure), and heated to the desired temperature (between 670 and 800°C). A positive pressure of argon (about 8 mm of mercury) was maintained through a small pipe to the upper cap. After soaking for from 2 to 5 hr, the container was quenched by directing a stream of water onto the base, so that solidification of the aluminum-rich layer was rapid and essentially unidirectional. Analyses were made on drillings taken from the bottom of the ingots after machining off the surface layers. Pre-

Jan 1, 1949

Jan 1, 1965

By D. W. Gentry, H. E. Sherer

Determining the age at which to replace a specific piece of mining equipment, and choice of the best possible replacement, is a problem common to nearly all mining operations. This paper examines the data required for intelligent equipment replacement decisions and discusses how to predict future repair cost from historic data, determine the total cost of various replacement alternatives, and evaluate the different replacement alternatives. Various operations research and computer methods were used to develop this easily-used, practical equipment replacement method.

Jan 1, 1984

By P. D. Bush, E. H. Gates, M. D. Vijayaraghavan, L. F. Engle

The process developed over the last few years by Republic Steel Corporation in conjunction with Colorado School of Mines Research Institute has been used as a basis for the conceptual engineering of full size plants. The paper will cover the equipment design criteria, equipment design itself, and the integration of the complex unit operations. There are unique features of agitation and use of gas media through- out. The paper will provide an illustrative example of the process requirements for a variety of raw material feeds. It will discuss the materials of construction approach required.

Jan 1, 1973

By J. Burns Read, Charles H. Fulton

A previous article1 by the authors contained a general description of the new roasting furnace herein described but it did not go into detail as to the metallurgical behavior or the results obtained. Believing that such information would be of great value, they have elaborated on the subject and have given many unpublished details. The furnace described applies the principle of roasting finely divided zinc-sulfide ores, now produced in large quantity by the flotation process, in gaseous suspension; that is, the ore particles are carried, in suspension, in a current of air and gaseous products of the roast. The relatively great fineness of flotation concentrate presents difficulties and problems of roasting in furnaces of the ordinary type; the fine ore is forwarded through the furnace in the form of a shallow bed and its very fineness leads to dense impervious bedding which prevents oxygen from reaching the interior of the bed, thus unduly lengthening the time of roasting and preventing the elimination of the last of the sulfur. The fineness of the concentrate, normally, should lead to a rapid and complete roast, for the speed of roasting is a function of the surface exposed to oxygen, which surface is greatest, per unit of weight, in very fine material. The difficulty in bed roasting is to get the oxygen to the particle. If the fine ore, during the roasting, could be freely suspended in oxidizing gases, full advantage could be taken of the great surface conferred by its fineness. This fundamental idea, of course, is not new, for the Stedtefelt furnace, familiar to the older metallurgists, is an example of it; but the manner in which this is accomplished may be new. The numerous efforts to roast in gaseous suspension show that the idea is attractive; in fact, an analysis would indicate that it is the most reason-

Jan 1, 1925